8C3831 SEAL-V RING Caterpillar parts
245
Rating:
Alternative (cross code) number:
CA8C3831
8C-3831
8C3831
CA8C3831
8C-3831
8C3831
Weight: 0.05 pounds 0 kg.
Information:
INSTALLED WIDTH
15.49
mm
MAXIMUM CONTACT DIAMETER
0
mm
MAXIMUM RPM
0
MAXIMUM SHAFT OD
146.05
mm
MINIMUM CONTACT DIAMETER
0
mm
MINIMUM SHAFT OD
146.05
mm
MATERIAL
NITRILE
EXCAVATOR,
Compatible equipment models: 8C3831:
Number on catalog scheme:
12
For full view, you need register
Information:
Removal Procedure
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01261423
Disconnect tube assembly (1). Remove bolts (3) and fuel transfer pump (2) and the O-ring seal.Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 2 g01261423
Connect tube assembly (1). Position fuel transfer pump (2) and the O-ring seal. Install bolts (3) .
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01261423
Disconnect tube assembly (1). Remove bolts (3) and fuel transfer pump (2) and the O-ring seal.Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 2 g01261423
Connect tube assembly (1). Position fuel transfer pump (2) and the O-ring seal. Install bolts (3) .
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
120G, 120H, 12E, 12G, 12H, 12H NA, 130G, 140, 140G, 140H, 140H NA, 141, 14G, 14H, 14H NA, 153, 16, 160G, 163, 1693, 16G, 16H, 16H NA, 172, 183, 184, 191, 214B, 215, 215B, 225, 225D, 227, 229, 229D, 23...
1673C, 1693, 16G, 245, 3176, 3176B, 3176C, 3196, 3208, 3306, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3456, 613, 621E, 623F, 651E, 657E, 7155, 772B, 773B, 776, 785, 824C, 980B, 980C...
12E, 12F, 140, 141, 14E, 153, 16, 163, 1673, 1673B, 1676, 1693, 16M, 172, 173B, 183B, 191, 193, 215, 225, 225D, 227, 229, 229D, 231D, 235, 235B, 235C, 245, 245B, 24M, 30/30, 301.5, 3116, 3126, 3126B, ...
235, 245, 583T, 587R, 587T, 65C, 75C, 773E, 775E, 789D, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 85C, 992C, CB-334D, CB-334E, CB-335D, CG137-08, CG137-12, CP-433C, CS-431C, CS-433C, D6F SR, D6G SR, G3...
12G, 236D, 242D, 245, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP, 308E2 CR, 3181, 3306, 3306B, 3406, 3406B, 3406E, 3408, 623E, 65C, 65E, 75C, 75D, 75E, 784B, 784C, ...
120G, 120M, 12G, 12M, 130G, 140G, 140M, 14M, 160M, 1673C, 16G, 16H NA, 16M, 215, 225, 231D, 235, 245, 24M, 3160, 318C, 3208, 320C, 320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320...
173B, 183B, 235, 245, 300.9D, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 3...
245, 3406, 3408, 3412, 637D, 657E, 768C, 834B, 980C, 988B
120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16M...
245, 621, 623, 631C, 641B, 650B, 769, 772, 773, 777, 824, 824B, 824C, 825B, 826C, 834, 953, 980, 980C, 980F, 983, 988, 992, D10, D346, D348, D349, D375D, D397D
120G, 120M, 120M 2, 12G, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14E, 14M, 153, 160M, 160M 2, 160M 3, 160M 3 AWD, 163, 16G, 16M, 173B, 183B, 215, 225, 235, 245, 245B, 245...
245, 245B
215D, 229D, 231D, 235C, 235D, 245B, 245D, 621B, 627B, 637D, 776C, 777B, 784B, 785, 785B, 789, 789B, 793, 793B, 814B, 815B, 816B, 824C, 826C, 834B, 836, 916, 918F, 926, 928F, 936, 936F, 938F, 941, 943,...
215D, 225, 225D, 227, 229D, 330C, 330C MH, 330D MH, 623F, 623G, 834G, 834H, 854G, 854K, 938F, 938G, 938G II, 953, 953C, 963, 980K, 992G, 992K, D10T2
231D, 235B, 235C, 235D, 330B L, 330C FM, 330D FM, 568 FM LL, 836, 963, 963B, 963C, 973, D5H XL, D5R LGP, D6H, D6H XL, D6H XR, D6N, D6N LGP, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL, D7H, D7...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 231...
235, 235C, 245, 245B, 365B, 365B II, 365C, 365C L, 385B, 385C L, 5230, 5230B, 980G, 980G II, 980H, D11N, D11R, D11T
9X3582
SEAL-LIP TYPE
235, 235C, 245B
235, 235C, 245B
225, 225D, 227, 229, 229D, 836, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 960F, 962G, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 973, D10N, D10R, D11N, D8L, D9L, D9N, D9R, R1600
6E1693
SEAL-SHAFT
229D, 231D, 350, 375, 375 L, 5080, 5130, 5130B, 5230, 844, 854G, 990, 990 II, 992G
229D, 231D, 350, 375, 375 L, 5080, 5130, 5130B, 5230, 844, 854G, 990, 990 II, 992G
235C, 245B
9X7268
SEAL-LIP TYPE
235C, 245B
235C, 245B
4E5808
SEAL
235C, 235D
235C, 235D
235C, 235D, 245, 245D