8C4895 SEAL-HEAD Caterpillar parts
D11N, D11R, D11T, R1700 II, R1700G
Rating:
Alternative (cross code) number:
CA8C4895
8C-4895
8C4895
CA8C4895
8C-4895
8C4895
Weight: 0.03 pounds 0 kg.
Information:
ID
248.92
mm
MATERIAL
Urethane Rubber - 90 Duro
RADIAL HEIGHT
2.2
mm
CS<br>STYLE
Rect Rd
AXIAL WIDTH
5.5
LOAD HAUL DUMP, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 8C4895:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: This procedure assumes that the housing (front) is still on the engine. Do not follow this procedure if the housing (front) has been removed from the engine. Refer to this Disassembly and Assembly Manual, "Housing (Front) - Install" if the housing (front) has been removed from the engine.
Clean the oil seal housing (8) and inspect the oil seal housing for damage. If necessary, replace the housing (front). Refer to this Disassembly and Assembly Manual, "Housing (Front) - Remove and Housing (Front) - Install".
Check the face on the pulley that contacts the crankshaft front seal for wear. If necessary, repair the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Wear Sleeve (Front) - Remove and Crankshaft Wear Sleeve (Front) - Install" for further details. Note: A sleeve (5) is attached to the new crankshaft front seal (6). Do not remove the sleeve (5) at this time. Discard the new crankshaft front seal (6) if the sleeve (5) is not installed on the new crankshaft front seal.
Illustration 1 g01148784
The Tooling (A) includes items 1, 2, 3, 4, 7 and 9.
Install the fastener plate (7) onto the front of the crankshaft. Install the nut (1) and the pressure plate (2) onto the threaded bar (3). Note: Do not lubricate the crankshaft front seal (6). Do not lubricate the oil seal housing (8).
Ensure that the lip of the crankshaft front seal that is spring loaded is facing toward the inside of the front housing and that it is square with the bore of the housing for the crankshaft front seal.
Align the assembly of the sleeve (5) and the crankshaft front seal (6) to the front of the oil seal housing (8).
Install the adapter (4) onto the sleeve (5).
Install the pressure plate (2) onto the adapter (4) and tighten the threaded bar (3) onto the fastener plate (7). Check the alignment of the assembly and the crankshaft front seal (6) to the oil seal housing (8).
Insert a suitable rod through the hole (9) in the threaded bar (3) in order to prevent the threaded rod from turning as the nut (1) is tightened. Tighten the nut (1) in order to push the crankshaft front seal (6) into the oil seal housing (8). Continue to tighten the nut (1) until contact is made with the bottom face of the oil seal housing (8).
Turn the sleeve (5) counterclockwise and pull the sleeve at the same time in order to remove the sleeve from the oil seal housing (8). Remove the adapter (7).
Immediately install the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Pulley - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: This procedure assumes that the housing (front) is still on the engine. Do not follow this procedure if the housing (front) has been removed from the engine. Refer to this Disassembly and Assembly Manual, "Housing (Front) - Install" if the housing (front) has been removed from the engine.
Clean the oil seal housing (8) and inspect the oil seal housing for damage. If necessary, replace the housing (front). Refer to this Disassembly and Assembly Manual, "Housing (Front) - Remove and Housing (Front) - Install".
Check the face on the pulley that contacts the crankshaft front seal for wear. If necessary, repair the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Wear Sleeve (Front) - Remove and Crankshaft Wear Sleeve (Front) - Install" for further details. Note: A sleeve (5) is attached to the new crankshaft front seal (6). Do not remove the sleeve (5) at this time. Discard the new crankshaft front seal (6) if the sleeve (5) is not installed on the new crankshaft front seal.
Illustration 1 g01148784
The Tooling (A) includes items 1, 2, 3, 4, 7 and 9.
Install the fastener plate (7) onto the front of the crankshaft. Install the nut (1) and the pressure plate (2) onto the threaded bar (3). Note: Do not lubricate the crankshaft front seal (6). Do not lubricate the oil seal housing (8).
Ensure that the lip of the crankshaft front seal that is spring loaded is facing toward the inside of the front housing and that it is square with the bore of the housing for the crankshaft front seal.
Align the assembly of the sleeve (5) and the crankshaft front seal (6) to the front of the oil seal housing (8).
Install the adapter (4) onto the sleeve (5).
Install the pressure plate (2) onto the adapter (4) and tighten the threaded bar (3) onto the fastener plate (7). Check the alignment of the assembly and the crankshaft front seal (6) to the oil seal housing (8).
Insert a suitable rod through the hole (9) in the threaded bar (3) in order to prevent the threaded rod from turning as the nut (1) is tightened. Tighten the nut (1) in order to push the crankshaft front seal (6) into the oil seal housing (8). Continue to tighten the nut (1) until contact is made with the bottom face of the oil seal housing (8).
Turn the sleeve (5) counterclockwise and pull the sleeve at the same time in order to remove the sleeve from the oil seal housing (8). Remove the adapter (7).
Immediately install the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Pulley - Remove and Install".
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
9X7391
SEAL-O-RING
CB-44B, D11R, D11T
CB-44B, D11R, D11T
2227007
SEAL AS
5130, 5130B, D11N, D11R, D11T
5130, 5130B, D11N, D11R, D11T
1627864
SEAL GP-DUO-CONE
D10N, D10R, D10T, D10T2, D11R, D11T
D10N, D10R, D10T, D10T2, D11R, D11T
1725093
SEAL GP-DUO-CONE
D11R, D11T
D11R, D11T
8P8796
SEAL AS
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
8P8797
SEAL AS
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
7T1448
SEAL
D11N
D11N
9X4590
SEAL AS
D11N, D11R, D11T
D11N, D11R, D11T
8T1115
SEAL-PIVOT SHAFT
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
9W7234
SEAL GP-DUO-CONE
D11N, D11R
D11N, D11R
8T2863
SEAL-U-CUP
D11N, D11R, D11T
D11N, D11R, D11T
1804363
SEAL-RECTANGULAR
D10N, D10R, D11R
D10N, D10R, D11R
1665452
SEAL-PISTON
R1700 II, R1700G
R1700 II, R1700G
1619836
SEAL-D-RING
R1700G
R1700G
1619835
SEAL-D-RING
R1700G
R1700G
1619834
SEAL-D-RING
R1700G
R1700G
2565098
SEAL
R1700G
R1700G
2928260
SEAL
R1700G
R1700G
2020663
SEAL-RING
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
1237276
SEAL-RING
793D, 793F, 793F-XQ
793D, 793F, 793F-XQ
2027482
SEAL-O-RING
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
2963460
SEAL-LIP TYPE
789D, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
789D, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
2287098
SEAL-O-RING
793D
793D
5P0559
SEAL
793D
793D