8C9135 SEAL-LIP TYPE Caterpillar parts
225, 225D, 227, 229D, 963, D11N, D11R
Rating:
Alternative (cross code) number:
CA8C9135
8C-9135
8C9135
CA8C9135
8C-9135
8C9135
Weight: 0.24 pounds 0 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Compatible equipment models: 8C9135:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2 Start By:
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01255892
Attach Tooling (A) and a suitable lifting device to flywheel housing (3). The weight of flywheel housing (3) is approximately 39 kg (85 lb).
Remove bolts (1) that attach flywheel housing (2) to the cylinder block.
Remove bolts (3) and (4) that attach flywheel housing (2) to the engine oil pan.
Remove flywheel housing (3) with the suitable lifting device. If necessary, tap the flywheel housing with a soft faced hammer in order to separate the flywheel housing from the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the rear face of the cylinder block and the mating surface of flywheel housing (2).
Illustration 2 g01255903Note: Inspect the dowels in the cylinder block that align flywheel housing (2). Replace the dowels, if necessary.
Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (3) is approximately 39 kg (85 lb). Position flywheel housing (2).
Install bolts (1) that attach the flywheel housing (3) to the cylinder block.
Install bolts (3) and (4) that attach the flywheel housing (2) to the engine oil pan. Tighten bolts (1), (3), and (4) to the following torque: M10 "8.8" ... 44 N m (33 lb ft)M10 "10.9" ... 63 N m (46 lb ft)M12 "8.8" ... 75 N m (55 lb ft)M12 "10.9" ... 115 N m (85 lb ft)
Remove Tooling (A) and the suitable lifting device from flywheel housing (2).
Check the alignment of the flywheel housing with the cylinder block. Refer to Testing and Adjusting, "Flywheel Housing - Inspect". End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2 Start By:
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01255892
Attach Tooling (A) and a suitable lifting device to flywheel housing (3). The weight of flywheel housing (3) is approximately 39 kg (85 lb).
Remove bolts (1) that attach flywheel housing (2) to the cylinder block.
Remove bolts (3) and (4) that attach flywheel housing (2) to the engine oil pan.
Remove flywheel housing (3) with the suitable lifting device. If necessary, tap the flywheel housing with a soft faced hammer in order to separate the flywheel housing from the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the rear face of the cylinder block and the mating surface of flywheel housing (2).
Illustration 2 g01255903Note: Inspect the dowels in the cylinder block that align flywheel housing (2). Replace the dowels, if necessary.
Attach Tooling (A) and a suitable lifting device to flywheel housing (2). The weight of flywheel housing (3) is approximately 39 kg (85 lb). Position flywheel housing (2).
Install bolts (1) that attach the flywheel housing (3) to the cylinder block.
Install bolts (3) and (4) that attach the flywheel housing (2) to the engine oil pan. Tighten bolts (1), (3), and (4) to the following torque: M10 "8.8" ... 44 N m (33 lb ft)M10 "10.9" ... 63 N m (46 lb ft)M12 "8.8" ... 75 N m (55 lb ft)M12 "10.9" ... 115 N m (85 lb ft)
Remove Tooling (A) and the suitable lifting device from flywheel housing (2).
Check the alignment of the flywheel housing with the cylinder block. Refer to Testing and Adjusting, "Flywheel Housing - Inspect". End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
3E6758
SEAL-LIP TYPE
AP-1055B, AP-655C, AP-655D, AP1055E, BG-2455D, BG1055E, BG655D, D10N, D10R, D10T, D10T2, D11R, D11T
AP-1055B, AP-655C, AP-655D, AP1055E, BG-2455D, BG1055E, BG655D, D10N, D10R, D10T, D10T2, D11R, D11T
9X7391
SEAL-O-RING
CB-44B, D11R, D11T
CB-44B, D11R, D11T
2227007
SEAL AS
5130, 5130B, D11N, D11R, D11T
5130, 5130B, D11N, D11R, D11T
1627864
SEAL GP-DUO-CONE
D10N, D10R, D10T, D10T2, D11R, D11T
D10N, D10R, D10T, D10T2, D11R, D11T
1725093
SEAL GP-DUO-CONE
D11R, D11T
D11R, D11T
8P8796
SEAL AS
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
8P8797
SEAL AS
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
7T1448
SEAL
D11N
D11N
9X4590
SEAL AS
D11N, D11R, D11T
D11N, D11R, D11T
8T1115
SEAL-PIVOT SHAFT
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
9W7234
SEAL GP-DUO-CONE
D11N, D11R
D11N, D11R
8T2863
SEAL-U-CUP
D11N, D11R, D11T
D11N, D11R, D11T
8T7321
SEAL-FACE
235B
235B
8T7157
SEAL-FACE
245, 508, D8L, D9N
245, 508, D8L, D9N
6Y0518
SEAL GP-DUO-CONE
235C, 245B
235C, 245B
9W7211
SEAL GP-DUO-CONE
14G, 215C, 235C, 235D, 245B, 518, 528
14G, 215C, 235C, 235D, 245B, 518, 528
8T7199
SEAL-FACE
225
225
8C9127
SEAL AS
215D, 225D, 229, 245B, 5230, 824G, 980C, 980F, 980F II, 980G, 988F II, D10N, D11N, D11R, D25D, D300E, D350E, D400E, D40D, D8L, D8N, D9N, D9R, R1600, R1600G
215D, 225D, 229, 245B, 5230, 824G, 980C, 980F, 980F II, 980G, 988F II, D10N, D11N, D11R, D25D, D300E, D350E, D400E, D40D, D8L, D8N, D9N, D9R, R1600, R1600G
9W6717
SEAL GP
245B
245B
8T7286
SEAL-FACE
120G, 235, 637E
120G, 235, 637E
8T7327
SEAL-FACE
120G, 12G, 140G, 16G, 235, 943
120G, 12G, 140G, 16G, 235, 943
9W6649
SEAL GP-DUO-CONE
235C, 517, 527, 578, 583R, 973, D5HTSK II, D6H, D6H XL, D6R, D7H, D7R, D8L, D8N, D8R, D9N, OEMS
235C, 517, 527, 578, 583R, 973, D5HTSK II, D6H, D6H XL, D6R, D7H, D7R, D8L, D8N, D8R, D9N, OEMS
1460780
SEAL-LIP TYPE
235C, 5110B, 5230, 5230B, 657G, 793D, 963C, 993K
235C, 5110B, 5230, 5230B, 657G, 793D, 963C, 993K
8C9128
SEAL AS
225, 225D, 227, 229D, 963, D11N, D11R
225, 225D, 227, 229D, 963, D11N, D11R