8C9182 SEAL AS Caterpillar parts
312D2, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 5130B, CR20, P16, S25
Rating:
Alternative (cross code) number:
CA8C9182
8C-9182
8C9182
CA8C9182
8C-9182
8C9182
Weight: 0.22 pounds 0 kg.
CRUSHER, SHEAR-DEMOLITION/SCRAP,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$41.39
25 Apr 2022
US: Florida-Parts-Z
8C9182 - Seal AS fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$36.82
28 Nov 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL AS 8C9182 NEW
$23.33
16 Dec 2017
31 Hundredths Pounds
CTP: CTP
Caterpillar Piston Seal (8C9182)
8C9182 Caterpillar, Cylinder Seals Weight(lbs): 0.30 Length(cm): 25.4000 Width(cm): 30.4800 Depth(cm): 2.5400
8C9182 Caterpillar, Cylinder Seals Weight(lbs): 0.30 Length(cm): 25.4000 Width(cm): 30.4800 Depth(cm): 2.5400
This part in 2 request:
Show.
This information for suppliers only!
2023-08-07
2017-12-04
Number on catalog scheme:
16
For full view, you need register
Compatible equipment models: 8C9182:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 5P-3526 Piston Ring Compressor 1
C 8T-3052 Degree Wheel 1
D 4C-5593 Anti-Seize Compound
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the face of the connecting rod bearings for final assembly.
Apply clean engine oil to the cylinder liner bore, to the piston rings, and to the outer surface of the piston.Note: The piston and connecting rod are matched to a specific cylinder. Ensure that the connecting rod and pistons are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Illustration 1 g01103923
Note: Be careful not to damage the cylinder liner, the crankshaft journal during installation of the piston and the connecting rod.
Use Tooling (B) to install piston (3) and the connecting rod in the cylinder liner.Note: Install the connecting rod so that the bearing tab is located on the side of the piston cooling jet.
Install the upper connecting rod bearing in the connecting rod.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Pull the connecting rod onto the crankshaft journal.
Install the lower connecting rod bearing in the connecting rod bearing cap.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Illustration 2 g01103925
Position connecting rod bearing cap (2) on the connecting rod.Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side of the piston cooling jet.
Apply Tooling (D) to the threads of bolts (1). Install the bolts and tighten to a torque of 90 8 N m (66 6 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 5P-3526 Piston Ring Compressor 1
C 8T-3052 Degree Wheel 1
D 4C-5593 Anti-Seize Compound
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the face of the connecting rod bearings for final assembly.
Apply clean engine oil to the cylinder liner bore, to the piston rings, and to the outer surface of the piston.Note: The piston and connecting rod are matched to a specific cylinder. Ensure that the connecting rod and pistons are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Illustration 1 g01103923
Note: Be careful not to damage the cylinder liner, the crankshaft journal during installation of the piston and the connecting rod.
Use Tooling (B) to install piston (3) and the connecting rod in the cylinder liner.Note: Install the connecting rod so that the bearing tab is located on the side of the piston cooling jet.
Install the upper connecting rod bearing in the connecting rod.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Pull the connecting rod onto the crankshaft journal.
Install the lower connecting rod bearing in the connecting rod bearing cap.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Illustration 2 g01103925
Position connecting rod bearing cap (2) on the connecting rod.Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side of the piston cooling jet.
Apply Tooling (D) to the threads of bolts (1). Install the bolts and tighten to a torque of 90 8 N m (66 6 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
385B, CR20
325B L, 330, 330 FM L, 330 L, 330B L, 350, 350 L, CR20, P16
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
385B, 385C, 385C L, 390D, 390D L
328D LCR, 345B II, 345B L, 345C, 345C L, 345D L, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, E650
345B II, 345B L, 350, 365B, 365B II, 365B L
365B, 365B L
365C, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
3673933
SEAL-U-CUP
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
312D2, 385B, 385C, 385C L, 390D, 390D L, 988K
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 988K
3673932
SEAL-BUFFER
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
312D2, 374D L, 374F L, 385C L, 390D, 390D L, 390F L
1659295
SEAL-LIP TYPE
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
312D2, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
312D2, 350, 350 L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
4180993
SEAL
306E, 307E
306E, 307E
3857944
SEAL-AIR
318D2 L
318D2 L
312D2, 365B II, 365C, 365C L, 375, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 5110B
312D2, 365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
312D2, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B
115, 312D2, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B, 5110B, 901C, 902C, 903C, CR20, E70, H140CS, P16, S25