8T5919 SEAL-LIP TYPE Caterpillar parts
120G, 130G, 3304, 3306, 3306B, D250B, D4E, D5B, D5H, G3304, G3306, G936
Rating:
Alternative (cross code) number:
CA8T5919
8T-5919
8T5919
CA8T5919
8T-5919
8T5919
Weight: 0.05 pounds 0 kg.
ARTICULATED TRUCK, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$10.91
29 Dec 2023
US: Florida-Parts-Z
8T5919 - Seal 8C5210 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$10.91
30 Mar 2022
US: Florida-Parts-Z
8T5919 - Seal 8C5210 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 8T5919:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
B 1P-0820 Hydraulic Puller 1
8B-7548 Push-Puller Tool Group 1
8B-7559 Adapter 2
5H-1504 Hard Washer 3
9U-6600 Hand Hydraulic Pump 1
C 125-0200 Camshaft Pilot As 2
D 125-0201 Camshaft Guide As 1
E 8T-3169 Crank Assembly 1 Start By:
Remove the valve cover base. Refer to Disassembly and Assembly, "Valve Cover Base - Remove and Install".
Remove the speed/timing sensor. Refer to the Service Manual, "Electronic Troubleshooting" module.
Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module (ECM) and Personality Module (PM) - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01007161
Remove tube assemblies (1).
Remove bolts (3) and covers (2) from both sides of the engine.
Illustration 2 g00914348
Remove covers (4) from both sides of the front housing.
Illustration 3 g01053356
Pull valve lifters (5) away from the camshaft. Hold valve lifters (5) in position with O-ring seals.
Illustration 4 g01053366
Remove covers (6) for the camshaft drive gears from the flywheel housing.
Illustration 5 g01053357
Remove the bolt and plate (7) that fastens camshaft drive gear (8) to the camshaft.
Illustration 6 g00914453
Place the three washers from Tooling (B) behind plate (7) and install the bolt.
Do not apply more than 51675 kPa (7500 psi) pressure to the hydraulic puller. The adapters are rated at 6 1/2 tons each and the hydraulic puller is rated at 17 tons at 68900 kPa (10000 psi). If too much pressure is applied, the gear may be damaged.
Install Tooling (B) on camshaft drive gear (8). Apply 51675 kPa (7500 psi) to Tooling (B). Strike the screw on Tooling (B) with a hammer until camshaft drive gear (8) is free from the camshaft. Remove Tooling (B) and camshaft drive gear (8).
Illustration 7 g00613686
Remove bolts (9) and thrust washers (10) that fasten the camshaft to the engine block.
Perform Steps 5 through 9 for the camshaft on the other side of the engine.
Illustration 8 g00914454
Remove timing ring (11) from the camshaft.
Illustration 9 g00914462
Install Tooling (C) on each end of the camshaft. Note: Tooling (D) can be installed on the flywheel housing in order to remove the camshaft from the rear. Tooling (D) can also be installed on the front housing in order to remove the camshaft from the front of the engine.
Install Tooling (D) on the flywheel housing.
Install Tooling (E) on the end of Tooling (C). Note: The following Step is for 3508B Engines.Note: The weight of the camshaft for 3508 Engines is approximately 46 kg (101 lb). The camshaft is one piece.
Rotate the camshaft with Tooling (E). Pull the camshaft out of the engine until
Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
B 1P-0820 Hydraulic Puller 1
8B-7548 Push-Puller Tool Group 1
8B-7559 Adapter 2
5H-1504 Hard Washer 3
9U-6600 Hand Hydraulic Pump 1
C 125-0200 Camshaft Pilot As 2
D 125-0201 Camshaft Guide As 1
E 8T-3169 Crank Assembly 1 Start By:
Remove the valve cover base. Refer to Disassembly and Assembly, "Valve Cover Base - Remove and Install".
Remove the speed/timing sensor. Refer to the Service Manual, "Electronic Troubleshooting" module.
Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module (ECM) and Personality Module (PM) - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01007161
Remove tube assemblies (1).
Remove bolts (3) and covers (2) from both sides of the engine.
Illustration 2 g00914348
Remove covers (4) from both sides of the front housing.
Illustration 3 g01053356
Pull valve lifters (5) away from the camshaft. Hold valve lifters (5) in position with O-ring seals.
Illustration 4 g01053366
Remove covers (6) for the camshaft drive gears from the flywheel housing.
Illustration 5 g01053357
Remove the bolt and plate (7) that fastens camshaft drive gear (8) to the camshaft.
Illustration 6 g00914453
Place the three washers from Tooling (B) behind plate (7) and install the bolt.
Do not apply more than 51675 kPa (7500 psi) pressure to the hydraulic puller. The adapters are rated at 6 1/2 tons each and the hydraulic puller is rated at 17 tons at 68900 kPa (10000 psi). If too much pressure is applied, the gear may be damaged.
Install Tooling (B) on camshaft drive gear (8). Apply 51675 kPa (7500 psi) to Tooling (B). Strike the screw on Tooling (B) with a hammer until camshaft drive gear (8) is free from the camshaft. Remove Tooling (B) and camshaft drive gear (8).
Illustration 7 g00613686
Remove bolts (9) and thrust washers (10) that fasten the camshaft to the engine block.
Perform Steps 5 through 9 for the camshaft on the other side of the engine.
Illustration 8 g00914454
Remove timing ring (11) from the camshaft.
Illustration 9 g00914462
Install Tooling (C) on each end of the camshaft. Note: Tooling (D) can be installed on the flywheel housing in order to remove the camshaft from the rear. Tooling (D) can also be installed on the front housing in order to remove the camshaft from the front of the engine.
Install Tooling (D) on the flywheel housing.
Install Tooling (E) on the end of Tooling (C). Note: The following Step is for 3508B Engines.Note: The weight of the camshaft for 3508 Engines is approximately 46 kg (101 lb). The camshaft is one piece.
Rotate the camshaft with Tooling (E). Pull the camshaft out of the engine until
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
9D6582
SEAL-LIP TYPE
120G, 12G, 130G, 14G
120G, 12G, 130G, 14G
9D1521
SEAL
120G
120G
9D1520
SEAL
120G
120G
8D3902
SEAL-LIP TYPE
12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 160M, 160M 2,...
12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 160M, 160M 2,...
6V8081
SEAL-LIP TYPE
12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 160G
12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 160G
4D5497
SEAL-D-RING
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 16, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 16, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
7D8436
SEAL-D-RING
120H, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
120H, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
8D1791
SEAL
12G, 130G, 140G, 160G
12G, 130G, 140G, 160G
7D8884
SEAL
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, ...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, ...
7D8883
SEAL
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, ...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, ...
5F4258
SEAL
120G, 12G, 14G, 16G
120G, 12G, 14G, 16G
6G6242
SEAL
130G
130G
5F1053
SEAL-FOOT VALVE
3304, 3306, 3306B, 3406, 3406B, 3406E, 3408, 3412, 3412D, 3412E, C15, C18, D315, D364
3304, 3306, 3306B, 3406, 3406B, 3406E, 3408, 3412, 3412D, 3412E, C15, C18, D315, D364
7T5830
SEAL-RING
426, 428, 966R
426, 428, 966R
6V1902
SEAL-O-RING
3126B, 3176, 3176B, 3406B, 345B II, 345B II MH, 345B L, 375, 375 L, 5080, 5130, 5130B, 5230, 623E, 631E, 631G, 633E II, 637E, 637G, 7211, 7221, 725, 725C, 730, 730C, 735, 75, 793F, 793F AC, 793F CMD, ...
3126B, 3176, 3176B, 3406B, 345B II, 345B II MH, 345B L, 375, 375 L, 5080, 5130, 5130B, 5230, 623E, 631E, 631G, 633E II, 637E, 637G, 7211, 7221, 725, 725C, 730, 730C, 735, 75, 793F, 793F AC, 793F CMD, ...
2H5001
SEAL
120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14E, 16, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 1674, 1676, 215, 2...
120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14E, 16, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 1674, 1676, 215, 2...
7W9064
SEAL
428
428
6V1890
SEAL
215B, 215D, 225, 231D, 235, 235B, 235C, 245, 322, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 416, 428, 621E, 623E, 627E, 631E, 633E II, 637E, 651E, 657E, 795F AC, D9T
215B, 215D, 225, 231D, 235, 235B, 235C, 245, 322, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 416, 428, 621E, 623E, 627E, 631E, 633E II, 637E, 651E, 657E, 795F AC, D9T
5P7069
SEAL
426, 428, 613B, 615
426, 428, 613B, 615
8T1174
SEAL-LIP TYPE
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 517, 5...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 517, 5...
5P5937
SEAL
446, 613, 814, 815, 816, 931, 950, 966C, 980B, D4D
446, 613, 814, 815, 816, 931, 950, 966C, 980B, D4D
5S6296
SEAL-LIP TYPE
120G, 1673C, 235, 3304, 3306, 627, 920, 950, 950B, 955K, 963, 966C, 973, D250B, D25C, D300B, D30C, D350C, D35C, D4D, D4E, D6C, D6D, D6H, D7F, G3306, G936
120G, 1673C, 235, 3304, 3306, 627, 920, 950, 950B, 955K, 963, 966C, 973, D250B, D25C, D300B, D30C, D350C, D35C, D4D, D4E, D6C, D6D, D6H, D7F, G3306, G936