8T7171 SEAL-FACE Caterpillar parts
966D, 980C, D10, D4H, D9L
Rating:
Alternative (cross code) number:
CA8T7171
8T-7171
8T7171
CA8T7171
8T-7171
8T7171
Weight: 0.01 pounds 0 kg.
TRACK-TYPE TRACTOR, WHEEL LOADER,
Compatible equipment models: 8T7171:
Number on catalog scheme:
13
For full view, you need register
Information:
Double Plate Clutch
Illustration 1 g00511415
Typical IllustrationNote: After clutch has been installed on engine, hit output shaft sharply on the end to relieve any preload that may result due to resistance of pilot bearing being pressed into the flywheel. (1) Bearing Adjustment (End Clearance) Tighten bearing retainer until there is no clearance between cup and cone. Back off retainer two or three notches and assemble the lock. Strike output end of shaft to seat the inner bearing cup against the bearing retainer. Adjust to the following end play. ... 0.15 to 0.25 mm (.006 to .010 inch)Clutch Engagement Check on the Engine
A torque of 295 to 392 N m (214 to 291 lb ft) on the splined clutch lever shaft is required in order to engage the clutch.
Illustration 1 g00511415
Typical IllustrationNote: After clutch has been installed on engine, hit output shaft sharply on the end to relieve any preload that may result due to resistance of pilot bearing being pressed into the flywheel. (1) Bearing Adjustment (End Clearance) Tighten bearing retainer until there is no clearance between cup and cone. Back off retainer two or three notches and assemble the lock. Strike output end of shaft to seat the inner bearing cup against the bearing retainer. Adjust to the following end play. ... 0.15 to 0.25 mm (.006 to .010 inch)Clutch Engagement Check on the Engine
A torque of 295 to 392 N m (214 to 291 lb ft) on the splined clutch lever shaft is required in order to engage the clutch.
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
826C, 980C
826C, 980C
980C
980C
980C
16, 772, 777, D10
D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
D10N, D10R, D10T, D10T2, D9L
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
D10N, D10R, D8L, D9L, D9N, D9R
966D, 980C
980C
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 336D L, 336D LN, 336E HVG, 568 FM LL, 980C, 980F, 980F II
966G, 972G, 972G II, 980C, 980F, D10N, D10R
966G, 972G, 972G II, 980C, 980F, D25D, D350E, D400E
5130, 5130B, 950H, 980C, 980F, 980F II, R1600, R1600G, R1600H
994, 994D, 994F, 994H
785, 994
9X2530
SEAL
814B, 815B, 826C, 950B, 950F, 966F, 980C, 980F
814B, 815B, 826C, 950B, 950F, 966F, 980C, 980F
5V8467
SEAL
815B, 826C, 950B, 966D, 980C
815B, 826C, 950B, 966D, 980C
5V8657
SEAL
815B, 826C, 950B, 966D, 980C
815B, 826C, 950B, 966D, 980C
120G, 12G, 130G, 140G, 14G, 16G, 966D, 980C