8T7295 SEAL-FACE Caterpillar parts
651E, 657E, 785, 789, D10N, D11N, D7H, D8N
Rating:
Alternative (cross code) number:
CA8T7295
8T-7295
8T7295
CA8T7295
8T-7295
8T7295
Weight: 0.01 pounds 0 kg.
TRACK-TYPE TRACTOR, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$8.13
08 Feb 2022
US: Florida-Parts-Z
5W1871 - O Ring PK-20 4J0528 2W7002 8T7295 fits Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Number on catalog scheme:
3
For full view, you need register
Compatible equipment models: 8T7295:
Information:
Remove Left Camshaft Housing
preparatory steps: a) remove left air cleaner housingb) remove left valve coverc) remove fuel injection lines (left side)1. Rotate the crankshaft to top dead center compression stroke No. 1 piston. See LOCATING TOP DEAD CENTER COMPRESSION POSITION FOR NO. 1 PISTON in TESTING AND ADJUSTING. 2. Remove the camshaft housing end cover (1) and Service Meter as a unit. 3. Remove the camshaft housing mounting bolts (4), nuts (3), and locks.4. Remove the inner fuel injection lines (2).5. Remove the remaining camshaft housing-to-cylinder head mounting bolts.6. Install two 3/8" -16 NC forged eyebolts in camshaft housing. Attach a hoist, and remove the camshaft housing - weight 120 lbs. (54 kg).Install Left Camshaft Housing
1. Adjust all valve lash adjustment screws for maximum valve clearance.2. Align the phasing gear timing marks, and install the camshaft timing pin in inlet camshaft timing slot.3. Check to be sure that crankshaft is at TDC compression position No. 1 piston. The crankshaft will also be in this position if: (a) The timing pin can be inserted into slot in fuel injection pump camshaft as outlined in FUEL INJECTION PUMP CAMSHAFT TIMING in TESTING AND ADJUSTING.(b) The timing pin for the right camshaft housing will drop into timing slot in right inlet camshaft (if housing hasn't been disturbed).
If above procedure relating to valve lash, camshaft timing marks, and crankshaft position is not followed, damage to the engine can result.
4. Attach a hoist, and position camshaft housing on engine making sure that exhaust camshaft gear and drive gear are meshed. Install camshaft housing retaining bolts, nuts, and locks.5. Install the inner fuel injection lines. Tighten retaining nuts to 30 5 lb. ft. (4,1 0,7 mkg).6. Install the camshaft housing end cover and Service Meter.7. Remove all timing pins from their timing slots. Install timing pins in their respective storage positions.concluding steps: a) install fuel injection lines (left side)b) install left air cleaner housingc) adjust valve clearanced) install left valve cover
preparatory steps: a) remove left air cleaner housingb) remove left valve coverc) remove fuel injection lines (left side)1. Rotate the crankshaft to top dead center compression stroke No. 1 piston. See LOCATING TOP DEAD CENTER COMPRESSION POSITION FOR NO. 1 PISTON in TESTING AND ADJUSTING. 2. Remove the camshaft housing end cover (1) and Service Meter as a unit. 3. Remove the camshaft housing mounting bolts (4), nuts (3), and locks.4. Remove the inner fuel injection lines (2).5. Remove the remaining camshaft housing-to-cylinder head mounting bolts.6. Install two 3/8" -16 NC forged eyebolts in camshaft housing. Attach a hoist, and remove the camshaft housing - weight 120 lbs. (54 kg).Install Left Camshaft Housing
1. Adjust all valve lash adjustment screws for maximum valve clearance.2. Align the phasing gear timing marks, and install the camshaft timing pin in inlet camshaft timing slot.3. Check to be sure that crankshaft is at TDC compression position No. 1 piston. The crankshaft will also be in this position if: (a) The timing pin can be inserted into slot in fuel injection pump camshaft as outlined in FUEL INJECTION PUMP CAMSHAFT TIMING in TESTING AND ADJUSTING.(b) The timing pin for the right camshaft housing will drop into timing slot in right inlet camshaft (if housing hasn't been disturbed).
If above procedure relating to valve lash, camshaft timing marks, and crankshaft position is not followed, damage to the engine can result.
4. Attach a hoist, and position camshaft housing on engine making sure that exhaust camshaft gear and drive gear are meshed. Install camshaft housing retaining bolts, nuts, and locks.5. Install the inner fuel injection lines. Tighten retaining nuts to 30 5 lb. ft. (4,1 0,7 mkg).6. Install the camshaft housing end cover and Service Meter.7. Remove all timing pins from their timing slots. Install timing pins in their respective storage positions.concluding steps: a) install fuel injection lines (left side)b) install left air cleaner housingc) adjust valve clearanced) install left valve cover
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
D10N, D10R, D9R
D10N, D10R, D10T, D10T2, D9L
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
D10N, D8L, D9N
D11N, D11R, D11T
D10, D11N, D11R, D11T
D11N, D11R
D11N, D11R, D11T
D10N, D10R, D8L, D9L, D9N, D9R
D10N
10, 10S, D10, D11N
2Y5823
SEAL
120B, 930R, 966R
120B, 930R, 966R
D6D, D6E, D6F SR
651E, 657E, D10N, D11N, D6D, D7H
D5B, D6D
980C, D6D
D8N
651E, 657E, 769C, 773B, 775B, 824C, 826C, 990, 992C, 992D
D5H
8T8978
SEAL-FACE
651E, 657E, D6H
651E, 657E, D6H
D6H, D7H, D8N
D7H, D8N, IT28, IT28B
9T5947
SEAL
D7H, D8N
D7H, D8N