8T9588 SEAL-O-RING Caterpillar parts
3176, 3176B, 374F L, 390F L, 735B, 740B, 75, 770G, 770G OEM, 772G, 772G OEM, 773G, 773G OEM, 775G, 775G OEM, 777G, 824K, 825K, 826K, 834K, 836K, 844K, 854K, 988K, 990K, 992K, 993K, C15, C18, C27, C32,...
Rating:
Alternative (cross code) number:
CA8T9588
8T-9588
8T9588
CA8T9588
8T-9588
8T9588
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.53
mm
DASH SIZE
224
ID
44.04
mm
MATERIAL
(EPDM) 70 Duro
OD
0
mm
ARTICULATED TRUCK, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$6.73
30 Jan 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
CATERPILLAR SEAL 8T9588 NEW
$8.14
27 May 2022
0.1102[0.05] Pounds
US: ProperBuy
CTP Caterpillar Epdm (70) O-Ring (8t9588) Aftermarket
CTP
CTP
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 8T9588:
Information:
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.Note: Do not strike the diodes. The shock of such an impact can damage the diodes. Use proper tools in order to press the diodes in the mountings.
Illustration 1 g00628072
Install 3 diodes (11) in heat sink (12) .
Illustration 2 g00628068
Note: Do not strike the bushing. Shocks from striking the housing can cause damage.
Press bushing (43) in housing (14) .
Install 3 diodes (13) in housing (14) .
Illustration 3 g00628067
Press collar (42) on rotor (39) .
Slide retainer (41) on rotor (39) .
Press bearing (40) on rotor (39) .
Illustration 4 g00628063
Press housing (31) on rotor (39) and bearing (40) .
Install 4 screws (38) in housing (31) .
Illustration 5 g00628057
Note: Do not strike the bearing. Shocks from striking the housing can cause damage.
Install the inner race. Press bearing (37) into the housing.
Illustration 6 g00628043
Press cap (36) in housing (14) .
Illustration 7 g00628041
Install the coil and support (34) in housing (14). Guide the field leads and the grommet through the hole as the coil is installed in housing (14). Install 3 screws (33) .
Illustration 8 g00628037
Press the stator (32) and housing (14) together. Guide the stator leads and the grommet through the hole as the stator is installed in housing (14) .
Illustration 9 g00628035
Note: Do not damage exposed stator windings or field windings. Bumping the windings or scraping the windings may break the insulation. Broken insulation may create a short circuit or a ground.
Join housing (31) and housing (14). Install 4 bolts (30) .
Illustration 10 g00627853
Note: Many of the alternator's internal components are covered with dielectric grease. If the grease is removed, reapply the grease.
Illustration 11 g00627855
Install Insulator (29). Install the heat sink and diode assembly (12) in housing (14) .
Illustration 12 g00627840
Install separator (28) .
Install alternator output terminal (27). Install insulator (26). Install the nut and washer (25) .
Install diode trio (24) and install screw (23) .
Illustration 13 g00627832
Install the 3 screws and insulators (18). Connect wire (19) .
If the "R" terminal is used, install the following components: nut (20), lead (21), the washer and terminal (21) .
Illustration 14 g00627820
Install the screw and insulator (16). Connect capacitor lead (17) .
Illustration 15 g00627810
Note: The 3 output diodes (11) are located in heat sink (12). These diodes are identical in polarity. Diode (11) has red insulation on the wire. The 3 ground diodes (13) are located in housing (14). These diodes are identical in polarity. Diode (13) has black insulation on the wire.
Connect 6 diode leads. Connect 3 phase leads. Connect 3 stator phase leads. Install 3 nuts (15).
Table 1
Alternator Ground Current Flow of the Output Diodes Current Flow of the Ground Diodes
Negative Lead to the Heat Sink Housing to the Lead
Red Wire Black Wire
Illustration 16 g00627808
Install mounting plate
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.Note: Do not strike the diodes. The shock of such an impact can damage the diodes. Use proper tools in order to press the diodes in the mountings.
Illustration 1 g00628072
Install 3 diodes (11) in heat sink (12) .
Illustration 2 g00628068
Note: Do not strike the bushing. Shocks from striking the housing can cause damage.
Press bushing (43) in housing (14) .
Install 3 diodes (13) in housing (14) .
Illustration 3 g00628067
Press collar (42) on rotor (39) .
Slide retainer (41) on rotor (39) .
Press bearing (40) on rotor (39) .
Illustration 4 g00628063
Press housing (31) on rotor (39) and bearing (40) .
Install 4 screws (38) in housing (31) .
Illustration 5 g00628057
Note: Do not strike the bearing. Shocks from striking the housing can cause damage.
Install the inner race. Press bearing (37) into the housing.
Illustration 6 g00628043
Press cap (36) in housing (14) .
Illustration 7 g00628041
Install the coil and support (34) in housing (14). Guide the field leads and the grommet through the hole as the coil is installed in housing (14). Install 3 screws (33) .
Illustration 8 g00628037
Press the stator (32) and housing (14) together. Guide the stator leads and the grommet through the hole as the stator is installed in housing (14) .
Illustration 9 g00628035
Note: Do not damage exposed stator windings or field windings. Bumping the windings or scraping the windings may break the insulation. Broken insulation may create a short circuit or a ground.
Join housing (31) and housing (14). Install 4 bolts (30) .
Illustration 10 g00627853
Note: Many of the alternator's internal components are covered with dielectric grease. If the grease is removed, reapply the grease.
Illustration 11 g00627855
Install Insulator (29). Install the heat sink and diode assembly (12) in housing (14) .
Illustration 12 g00627840
Install separator (28) .
Install alternator output terminal (27). Install insulator (26). Install the nut and washer (25) .
Install diode trio (24) and install screw (23) .
Illustration 13 g00627832
Install the 3 screws and insulators (18). Connect wire (19) .
If the "R" terminal is used, install the following components: nut (20), lead (21), the washer and terminal (21) .
Illustration 14 g00627820
Install the screw and insulator (16). Connect capacitor lead (17) .
Illustration 15 g00627810
Note: The 3 output diodes (11) are located in heat sink (12). These diodes are identical in polarity. Diode (11) has red insulation on the wire. The 3 ground diodes (13) are located in housing (14). These diodes are identical in polarity. Diode (13) has black insulation on the wire.
Connect 6 diode leads. Connect 3 phase leads. Connect 3 stator phase leads. Install 3 nuts (15).
Table 1
Alternator Ground Current Flow of the Output Diodes Current Flow of the Ground Diodes
Negative Lead to the Heat Sink Housing to the Lead
Red Wire Black Wire
Illustration 16 g00627808
Install mounting plate
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
D10R, D10T, D10T2, D9R, D9T
D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
824G, 824G II, 824H, 826G, 826G II, 826H, 844, 844H, 844K, D8L, D9N, D9R
D10R, D10T, D10T2, D9R, D9T
D9R, D9T
330C, 330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 374F L
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
365C, 374D L, 374F L, 385B, 385C, 385C L, 390D, 390D L, 390F L
3176, 3176B, 3306C, 3508, 3508C, 3512, 3512B, 3516, 3516B, 3516C, 3612, 3616, 75, C30, C32, CG137-08, G3508, G3512, G3516, G3516B, PMG3516
206B, 214B, 3114, 3116, 3406E, 3408, 3456, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 385B, 5090B, 5130, 5130B, 5230, 5230B, 621F, 621G, 623G, 627F, 627G, 657B, 735, 740, 776C, 776D, ...
120G, 12G, 16G, 623E, 65, 797, 797B, 824G, 825G, 902, 904B, 904H, 906, 918F, 924F, 928F, 928G, 938F, 938G, 938G II, 980G, 994, 994D, 994F, 994H, AP-1000, AP-1050, CB-334D, CB-334E, CB-335D, CP-563, CS...
3W9089
SEAL
65, 75
65, 75
8R6793
SEAL
65, 75
65, 75
10, 215, 30/30, 613, 65, 65C, 75, 854G, 950 GC, 950G, 950G II, 950H, 950K, 955K, 955L, 962G, 962G II, 962H, 962K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 97...
3176, 3508, 3512, 3516, 75, C-10, C-12, D337, D346, D348, D349, D375D, D379A, D379B, D397D, D399, G399, R1700 II
120G, 12G, 130G, 140G, 14G, 16G, 227, 235, 245, 426, 428, 613B, 613C, 615, 615C, 621B, 621E, 623E, 627E, 631E, 637D, 637E, 651E, 657E, 769C, 771C, 772B, 773B, 775B, 785, 834B, 836, 931B, 955L, 988B, 9...
5P6606
SEAL
428
428
7W2645
SEAL
212, 428, AP-800, CS-323, PR-75, PS-110
212, 428, AP-800, CS-323, PR-75, PS-110
3176, 3176B, 633E II, 75, 953, 953B, 953C, 953D, D8H, D8K
214B, 215, 3114, 3116, 3126, 3126B, 3176, 3176B, 320 L, 3204, 3208, 325, 613B, 613C, 75, 918F, 924F, 938F, 943, 950F, 950F II, 953, 960F, CB-434, CB-634, CP-563, D250D, D4HTSK II, E200B, FB221, IT28, ...