8U3899 SEAL-O-RING Caterpillar parts
205B, 206B, 211B, 212B, 224B, 924G, 924GZ, CWAC-40, M312, M313C, M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C, MP15, P215, P360, S305, S365B, S465, VHC-30, VHP-30, VHS-50, VHS-60/3, VT30, VT...
Rating:
Alternative (cross code) number:
CA8U3899
8U-3899
8U3899
CA8U3899
8U-3899
8U3899
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
1.5
mm
ID
7
mm
MATERIAL
Nitrile (NBR) Rubber - 75 Duro
OD
0
mm
CRUSHER, WHEELED EXCAVATOR,
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8H-0663 Bearing Puller 1
5F-7345 Screw 1
126-7183 Crossblock 1
126-7177 Puller Leg 2 Start By:
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft gear may be a sliding fit on the crankshaft or an interference fit on the crankshaft.
Illustration 1 g01367358
Typical example
Illustration 2 g01341488
Typical example
If the crankshaft gear is a sliding fit on the crankshaft, remove crankshaft gear (1) from crankshaft (2). If the crankshaft gear is an interference fit on the crankshaft, use Tooling (A) in order to remove crankshaft gear (1) from crankshaft (2).
If necessary, remove key (3) from crankshaft (2). Note: Do not remove the key from the crankshaft unless the key is damaged.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged.
Illustration 3 g01367359
If necessary, install a new key (3) to crankshaft (2). Note: The crankshaft gear may be a sliding fit on the crankshaft or an interference fit on the crankshaft.
Hot parts or hot components can cause burns or personal injury. Do not allow hot parts or components to contact your skin. Use protective clothing or protective equipment to protect your skin.
If the crankshaft gear is a sliding fit on the crankshaft, align the keyway on crankshaft gear (1) with key (3) in the crankshaft. Install crankshaft gear (1) to crankshaft (2). If the crankshaft gear is an interference fit on the crankshaft, heat crankshaft gear (1) in an oven to 150° 50°C (302° 90°F). Align the keyway on crankshaft gear (1) with key (3) in the crankshaft. Install crankshaft gear (1) to crankshaft (2).Ensure that shoulder (4) of crankshaft gear (1) is toward the front of the engine.End By:
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8H-0663 Bearing Puller 1
5F-7345 Screw 1
126-7183 Crossblock 1
126-7177 Puller Leg 2 Start By:
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft gear may be a sliding fit on the crankshaft or an interference fit on the crankshaft.
Illustration 1 g01367358
Typical example
Illustration 2 g01341488
Typical example
If the crankshaft gear is a sliding fit on the crankshaft, remove crankshaft gear (1) from crankshaft (2). If the crankshaft gear is an interference fit on the crankshaft, use Tooling (A) in order to remove crankshaft gear (1) from crankshaft (2).
If necessary, remove key (3) from crankshaft (2). Note: Do not remove the key from the crankshaft unless the key is damaged.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged.
Illustration 3 g01367359
If necessary, install a new key (3) to crankshaft (2). Note: The crankshaft gear may be a sliding fit on the crankshaft or an interference fit on the crankshaft.
Hot parts or hot components can cause burns or personal injury. Do not allow hot parts or components to contact your skin. Use protective clothing or protective equipment to protect your skin.
If the crankshaft gear is a sliding fit on the crankshaft, align the keyway on crankshaft gear (1) with key (3) in the crankshaft. Install crankshaft gear (1) to crankshaft (2). If the crankshaft gear is an interference fit on the crankshaft, heat crankshaft gear (1) in an oven to 150° 50°C (302° 90°F). Align the keyway on crankshaft gear (1) with key (3) in the crankshaft. Install crankshaft gear (1) to crankshaft (2).Ensure that shoulder (4) of crankshaft gear (1) is toward the front of the engine.End By:
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA...
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H NA, 16H ...
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 211B, 214B, 215, 225, ...
120M, 120M 2, 12M, 216, 228, 236, 2384C, 247, 2470C, 248, 2484C, 2570C, 267, 2670C, 287, 3034, 3054, 3054B, 3054C, 3054E, 3056, 3056E, 307, 312, 312B L, 312C, 312E, 312E L, 314E CR, 314E LCR, 315, 315...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14H, ...
3054, 3054B, 3054C, 3054E, 3056, 3056E, 307, 312, 312B L, 312C, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315, 315B L, 315C, 317, 318D2 L, 414E, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E,...
120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M...
120M, 12G, 12M, 140, 140M, 141, 14G, 14H, 14H NA, 14M, 153, 16, 160M, 163, 16G, 16H, 16H NA, 16M, 191, 215, 215B, 225, 227, 229, 235, 235B, 235C, 235D, 24H, 24M, 30/30, 307, 330B L, 330C FM, 330C MH, ...
206B, 212B, 572R, 572R II, M312, M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C
CB-14, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325D MH, M330D
621H, 623H, 627H, D250B, D25C, D300B, D30C, D350C, D35C, D35HP, D400, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D...
8U6058
SEAL-O-RING
206B, 212B, M312, M313C, M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C
206B, 212B, M312, M313C, M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C
5W8380
SEAL
206, 212, 214B, 224B, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D, M322D MH
206, 212, 214B, 224B, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D, M322D MH
M315, M315C, M316C, M318
M315, M315C, M316C, M318, M318C
206B, 212B, 572R, 572R II, M312, M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C
206B, 212B, M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C
206B, 212B, 365B, 365B II, 735, 735B, 740, 740B, 776D, 777D, 777F, 777G, 834K, 836K, 844, 924K, 930K, 938K, 950 GC, 950H, 962H, 963D, 973D, 986H, 990 II, 993K, D10T, D10T2, D11T, D6T, D6T LGP, D6T XL,...
M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C
906H, 906H2, 907H, 907H2, 908H, 908H2, CP-533E, CP-54B, CS-533E, CS-54, CS-54B, CS-64B, M312, M313C, M313D, M315, M315C, M315D, M316C, M316D, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D...
515, 517, 525, 525B, 525C, 527, 535B, 535C, 545, 545C, D6N, GSH15, GSH15-60, GSH9, GSH9B, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH...