9H2258 SEAL-LIP TYPE Caterpillar parts
16, 508, 561B, 561C, 914G, 916, 924G, 924GZ, 924H, 924HZ, 924K, 926, 928F, 928G, 928H, 928HZ, 930G, 930K, 931B, 977D, D3B, D4D, D4E, D5, D5B, D5C, D5E, D9E, IT14G, IT18B, IT28, IT28F, IT28G
Rating:
Alternative (cross code) number:
CA9H2258
9H-2258
9H2258
CA9H2258
9H-2258
9H2258
Weight: 0.010 pounds 0 kg.
Information:
AXIAL WIDTH
12.7
mm
BORE DIAMETER
0
mm
CONSTRUCTION TYPE
SBI
MATERIAL
Nitrile Rubber (NBR) - 75 Duro
SEAL OD
73.13
mm
SHAFT OD
50.8
mm
COMPACT WHEEL LOADER, WHEEL SKIDDER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
BRAIN DUMP Inner Rear AXLE Seal Fits Massey Ferguson MF TEA-20 TO-30 195555M1, 81717512, 957E4233B, 9H2258, 9H-2258
BRAIN DUMP Aftermarket INNER REAR AXLE SEAL || Fits Massey Ferguson MF TEA-20 TO-30 || Tech Info: -ID : 2.0'' -BORE : 2.875'' -THICKNESS : 0.313'' || Replaces Part Number(s): 195555M1, 81717512, 957E4233B, 9H2258, 9H-2258
BRAIN DUMP Aftermarket INNER REAR AXLE SEAL || Fits Massey Ferguson MF TEA-20 TO-30 || Tech Info: -ID : 2.0'' -BORE : 2.875'' -THICKNESS : 0.313'' || Replaces Part Number(s): 195555M1, 81717512, 957E4233B, 9H2258, 9H-2258
MURNELAP for Inner Rear AXLE Seal for Part 195555M1 81717512 957E4233B 9H2258 9H-2258
MURNELAP For INNER REAR AXLE SEAL FOR PART 195555M1 81717512 957E4233B 9H2258 9H-2258 || Ensure a tight seal with the INNER REAR AXLE SEAL for part numbers 195555M1, 81717512, 957E4233B, 9H2258, and 9H2258, preventing leaks and maintaining optimal performance. || Pect your vehicle's rear axle from and damage by replacing worn seals with this INNER REAR AXLE SEAL compatible with various part numbers. || Ensures consistent and dependable operation of your lawn mower. || Verify Fit: For optimal performance, please review the product's appearance in the photo and verify it against the specified dimensions to ensure a precise fit.
MURNELAP For INNER REAR AXLE SEAL FOR PART 195555M1 81717512 957E4233B 9H2258 9H-2258 || Ensure a tight seal with the INNER REAR AXLE SEAL for part numbers 195555M1, 81717512, 957E4233B, 9H2258, and 9H2258, preventing leaks and maintaining optimal performance. || Pect your vehicle's rear axle from and damage by replacing worn seals with this INNER REAR AXLE SEAL compatible with various part numbers. || Ensures consistent and dependable operation of your lawn mower. || Verify Fit: For optimal performance, please review the product's appearance in the photo and verify it against the specified dimensions to ensure a precise fit.
195555M1, 81717512 Inner Rear AXLE Seal Fits Massey Ferguson MF TEA-20 TO-30 957E4233B, 9H2258, 9H-2258
Generic Replaces Part Number(s): 195555M1, 81717512, 957E4233B, 9H2258, 9H-2258 || Fits Massey Ferguson MF TEA-20 TO-30 || Tech Info: -ID : 2.0'' -BORE : 2.875'' -THICKNESS : 0.313'' || Aftermarket INNER REAR AXLE SEAL || 957E4233B, 9H2258, 9H-2258
Generic Replaces Part Number(s): 195555M1, 81717512, 957E4233B, 9H2258, 9H-2258 || Fits Massey Ferguson MF TEA-20 TO-30 || Tech Info: -ID : 2.0'' -BORE : 2.875'' -THICKNESS : 0.313'' || Aftermarket INNER REAR AXLE SEAL || 957E4233B, 9H2258, 9H-2258
Number on catalog scheme:
12
For full view, you need register
Compatible equipment models: 9H2258:
Information:
Access to C175 secondary and tertiary speed sensors require removal of components.
Remove air cleaner components.
Illustration 1 g02561819
(1) Access cover
Remove access panel (1).
Remove speed sensor cover.
Illustration 2 g02608836
Location of the secondary and tertiary speed sensors after access panel and cover removed.
(2) Speed sensors The secondary and tertiary speed sensors (2) are mounted in the top of the flywheel housing.
Illustration 3 g02562160
(3) Primary speed sensor The primary speed sensor (3) is located on the left side of the flywheel housing.
Remove the speed sensors from the housing. Check the condition of the plastic end of the speed sensors for wear and/or contaminants.
Clean the metal shavings and other debris from the face of the speed sensors. Use the procedure in the Service Manual in order to calibrate the speed sensors. The magnetic pickup (4) has a threaded end, and screws directly into the flywheel housing.
Illustration 4 g01890113
Remove the sensor. Inspect the condition of the end of the magnet. Look for signs of wear and contaminants.
Clean any debris from the face of the magnet.
Check the tension of the sliphead. Gently extend sliphead (5) for a minimum of 4 mm (0.16 inch). Then push back the sliphead. When the sliphead has the correct tension, at least 22 N (5 lb) of force is required to push in the sliphead from the extended position.
The sliphead must be fully extended when the speed/timing sensor is installed so that the sensor maintains the correct clearance with the speed-timing wheel. If the correct clearance is not maintained, the signal from the sensor will not be generated.Do not install the sensor between the teeth of the speed-timing wheel. Damage to the sensor would result. Before installing the sensor, ensure that a tooth of the wheel is visible in the mounting hole for the sensor.
Install the engine speed sensor.
Remove air cleaner components.
Illustration 1 g02561819
(1) Access cover
Remove access panel (1).
Remove speed sensor cover.
Illustration 2 g02608836
Location of the secondary and tertiary speed sensors after access panel and cover removed.
(2) Speed sensors The secondary and tertiary speed sensors (2) are mounted in the top of the flywheel housing.
Illustration 3 g02562160
(3) Primary speed sensor The primary speed sensor (3) is located on the left side of the flywheel housing.
Remove the speed sensors from the housing. Check the condition of the plastic end of the speed sensors for wear and/or contaminants.
Clean the metal shavings and other debris from the face of the speed sensors. Use the procedure in the Service Manual in order to calibrate the speed sensors. The magnetic pickup (4) has a threaded end, and screws directly into the flywheel housing.
Illustration 4 g01890113
Remove the sensor. Inspect the condition of the end of the magnet. Look for signs of wear and contaminants.
Clean any debris from the face of the magnet.
Check the tension of the sliphead. Gently extend sliphead (5) for a minimum of 4 mm (0.16 inch). Then push back the sliphead. When the sliphead has the correct tension, at least 22 N (5 lb) of force is required to push in the sliphead from the extended position.
The sliphead must be fully extended when the speed/timing sensor is installed so that the sensor maintains the correct clearance with the speed-timing wheel. If the correct clearance is not maintained, the signal from the sensor will not be generated.Do not install the sensor between the teeth of the speed-timing wheel. Damage to the sensor would result. Before installing the sensor, ensure that a tooth of the wheel is visible in the mounting hole for the sensor.
Install the engine speed sensor.
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
12E, 16, 769, 772, 773
16, 768B, 769, 769C, 772, 773, 773B, D35HP, D400
16, 772, 777, D10
120B, 12E, 140, 140B, 14E, 16, 824, 834
D9E
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 16, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
14E, 16
14E, 16
12E, 16
14E, 16
16
153, 611, 613, 613B, 615, 621, 621B, 621E, 623, 623B, 623E, 627B, 627E, 631E, 633C, 633D, 633E II, 637D, 637E, 651E, 657E, D5B, D5E, D6D
621, 621B, 621E, 627B, 627E, 630B, 631B, 631D, 631E, 631G, 633, 633D, 633E, 637D, 637E, 637G, 641B, 651, 651E, 657E, 657G, 8A, 8B, 8D, 977, 977H, 980, 980B, 983, 983B, 988, D5B, D5E, D6D, D6E, D6F SR,...
2503990
SEAL AS
953C, D5E
953C, D5E
D5E
561B, 561C, 633, 941, 951B, 955H, 955K, 955L, D4D, D4E, D4E SR, D5, D5B, D5E
561B, 561C, 777F, 910, 941, 951B, 955H, 955K, 955L, D4D, D4E, D4E SR, D5, D5B, D5E
561M, 561N, 939C, D4H, D4H XL, D4HTSK III, D5C III, D5G, D5M, D5N
561H, D4H, D4H XL, D4HTSK II, D4HTSK III, D5C, D5C III, D5G
561M, 561N, D4H, D4H XL, D4HTSK II, D5M, D5N
517, 561M, 561N, D3B, D4H, D4H XL, D4HTSK II, D4HTSK III, D5M, D5N, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
9X7541
SEAL-LIP TYPE
517, D4H XL, D4HTSK II, D4HTSK III
517, D4H XL, D4HTSK II, D4HTSK III
977, D5B, D5E, D6D, D6E, D6G, D6G SR, D6G2 XL