9J1340 SEAL ASSEM. (fire resistant) Caterpillar parts
235, 245, 988G
Rating:
Alternative (cross code) number:
CA9J1340
9J-1340
9J1340
CA9J1340
9J-1340
9J1340
Weight: 0.05 pounds 0 kg.
EXCAVATOR, WHEEL LOADER,
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3070 Fuel Injector Installer and Removal Tooling 2 Start By:
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the plug at the rear of the cylinder head. Allow the engine oil to drain from the hole in the cylinder head before the unit injector is removed.
Illustration 1 g01148880
Use a small flat head screwdriver to disconnect harness assembly (2) from unit injector (1).
Remove socket head bolts (3).
Illustration 2 g03030620
Install Tooling (A). Use Tooling (A) to remove unit injector (1) from the cylinder head. Note: Do not use a wire brush on the tip of the unit injector. Damage to the unit injector will occur.
Illustration 3 g01137291
Remove O-ring seals (6), (7), and (8) from unit injector (1). Remove backup rings (4), (5), and (9) from unit injector (1).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3070 Fuel Injector Installer and Removal Tooling 2 Start By:
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the plug at the rear of the cylinder head. Allow the engine oil to drain from the hole in the cylinder head before the unit injector is removed.
Illustration 1 g01148880
Use a small flat head screwdriver to disconnect harness assembly (2) from unit injector (1).
Remove socket head bolts (3).
Illustration 2 g03030620
Install Tooling (A). Use Tooling (A) to remove unit injector (1) from the cylinder head. Note: Do not use a wire brush on the tip of the unit injector. Damage to the unit injector will occur.
Illustration 3 g01137291
Remove O-ring seals (6), (7), and (8) from unit injector (1). Remove backup rings (4), (5), and (9) from unit injector (1).
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
235, 245, 5230, 657B, 657E
215, 235, 621, 621B, 621E, 627B, 627E, 773B, 936, 963, 973, 977K, 977L, 980, G936
225, 227, 229, 229D, 231D, 235, 235B, 235C
127, 172, 183, 184, 225, 227, 229, 235, 235B, 24, 25, 46, 910, 918F, 924F, IT18F, IT24F, PR-450C
4S8391
SEAL 76 in.
120, 12F, 12G, 140, 14E, 225, 768B, 769, 824B, 826B, 834, 950, 966C, 980B, 988, D5
120, 12F, 12G, 140, 14E, 225, 768B, 769, 824B, 826B, 834, 950, 966C, 980B, 988, D5
5P0594
SEAL 52 in.
225, 613
225, 613
235
235, 235C, 245
235, 235B, 235C, 245, 245D
235, 235B, 235C, 235D, 245, 245B, 245D
235, 235B, 235C, 245
235, 235C, 245