9X7313 SEAL-O-RING Caterpillar parts
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
Rating:
Alternative (cross code) number:
CA9X7313
9X-7313
9X7313
CA9X7313
9X-7313
9X7313
Weight: 0.20 pounds 0 kg.
Information:
BORE DIAMETER
714
mm
ID
701
mm
MATERIAL
(PTFE) Plastic - Glass filled
OD
711.66
mm
RADIAL HEIGHT
5.33
mm
CS ORIENTATION
CURVED OD
AXIAL WIDTH
3.53
TRACTOR, TRUCK,
Compatible equipment models: 9X7313:
Number on catalog scheme:
9
For full view, you need register
Information:
Introduction
This procedure is intended to give information on inspecting the flywheel.Refer to the Specifications Manual for any dimensions or specifications that are used for this procedure.Required Tools
Table 1
Required Tools
Part Number Part Description Qty
8T-5096 Dial Indicator Group 1 Inspection Procedure
Alignment of the Flywheel Face
Illustration 1 g00295952
Install the dial indicator in Illustration 1, as shown.
Set the pointer of the dial indicator to 0 mm (0 inch).
Turn the flywheel. Read the dial indicator for every 90 degrees. Note: During the check, keep the crankshaft pressed toward the front of the engine in order to remove any end clearance.
Calculate the difference between the lowest measurement and the highest measurement of the four locations. This difference must not be greater than 0.03 mm (0.001 inch) for every 25 mm (1.0 inch) of the radius of the flywheel. The radius of the flywheel is measured from the axis of the crankshaft to the contact point of the dial indicator. Flywheel Runout
Illustration 2 g00295954
Install the dial indicator in Illustration 2, as shown.
Set the pointer of the dial indicator to 0 mm (0 inch).
Turn the flywheel. Read the dial indicator for every 90 degrees.
Calculate the difference between the lowest measurement and the highest measurement of the four locations. This difference must not be greater than 0.30 mm (0.012 inch).
This procedure is intended to give information on inspecting the flywheel.Refer to the Specifications Manual for any dimensions or specifications that are used for this procedure.Required Tools
Table 1
Required Tools
Part Number Part Description Qty
8T-5096 Dial Indicator Group 1 Inspection Procedure
Alignment of the Flywheel Face
Illustration 1 g00295952
Install the dial indicator in Illustration 1, as shown.
Set the pointer of the dial indicator to 0 mm (0 inch).
Turn the flywheel. Read the dial indicator for every 90 degrees. Note: During the check, keep the crankshaft pressed toward the front of the engine in order to remove any end clearance.
Calculate the difference between the lowest measurement and the highest measurement of the four locations. This difference must not be greater than 0.03 mm (0.001 inch) for every 25 mm (1.0 inch) of the radius of the flywheel. The radius of the flywheel is measured from the axis of the crankshaft to the contact point of the dial indicator. Flywheel Runout
Illustration 2 g00295954
Install the dial indicator in Illustration 2, as shown.
Set the pointer of the dial indicator to 0 mm (0 inch).
Turn the flywheel. Read the dial indicator for every 90 degrees.
Calculate the difference between the lowest measurement and the highest measurement of the four locations. This difference must not be greater than 0.30 mm (0.012 inch).
Cat SIS web machinery list:
Parts seal Caterpillar catalog:
793, 793B, 793C
793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
789, 789B, 793, 793B
789B, 789C, 789D
785, 785C, 789, 789B, 789C, 789D
785, 789, 789B, 789C, 789D
789, 789B, 789C, 789D
769C, 769D, 771C, 771D, 785
793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ
550, 550B, 554, 560B, 564, 570, 570B, 574, 574B, 580, 580B, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, R1600, R1600G, R1600H, W330B, W345B II, W345C MH
120H, 120K, 12H, 12K, 135H, 140H, 140K, 143H, 160H, 160K, 163H, 793F
785
789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
1616770
SEAL
793C, 797, 797B
793C, 797, 797B
773B, 773D, 775D, 776D, 777D, 789B, 789C, 793B, 793C
793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 797, 797B
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ
24H, 69D, 768C, 769C, 769D, 770, 771C, 771D, 772, 772B, 773B, 773D, 773F, 775B, 775D, 775F, 776C, 776D, 777, 777B, 777D, 784B, 784C, 785, 785B, 785C, 789, 789B, 789C, 793, 793B, 793C, 797, 797B, AD40,...
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ