9X7422 SEAL-O-RING Caterpillar parts
Rating:
Alternative (cross code) number:
CA9X7422
9X-7422
9X7422
CA9X7422
9X-7422
9X7422
Weight: 0.01 pounds 0 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$625.00
01 Jun 2021
12.0[5.40] Pounds
US: OCEAN ENGINE PA
Cylinder Head Gasket Set for Caterpillar C15 Acert 1999-2007 618639 9Y6186 1548587 1013125 1085803 9X7422
HHP HIGHWAY & HEAVY PARTS We have ASE certified techs on staff to help you with all your gasket set neets. || Cylinder Head Gasket Set includes correct materials to ensure proper sealing. || Caterpillar C15 Diesel Gasket Set provides top engine performance from the right material selection. || Image(s) is for illustration purposes only and may not represent the actual part. || Caterpillar Diesel gasket set is manufactured in an ISO 9001: 2015 Certified facility.
HHP HIGHWAY & HEAVY PARTS We have ASE certified techs on staff to help you with all your gasket set neets. || Cylinder Head Gasket Set includes correct materials to ensure proper sealing. || Caterpillar C15 Diesel Gasket Set provides top engine performance from the right material selection. || Image(s) is for illustration purposes only and may not represent the actual part. || Caterpillar Diesel gasket set is manufactured in an ISO 9001: 2015 Certified facility.
For full view, you need register
Information:
130-1643 Control Group (Cat Monitoring System)
Trucks shipped without rear axle oil cooling as monitored with the new 130-1643 Control Group (Cat Monitoring System) should already be reworked by this writing and includes the rear axle filter group on 793B Trucks. The harness codes need to be verified as early production trucks with Rear Axle Pressure Lube & Filter System may have been incorrect.
Again, this update must be complete before the listed configurations can be used.
PROCEDURE:
On VIMS Trucks:
In the rear of the cab, you will find secured to a plate:1 - 100-5566 Bezel4 - 7Y-7256 Screw
1. Remove the four screws and bezel from the plate.2. A 40-pin Deutsch DRC connector can be found nearby which must be connected to this Cat Monitoring System Control; tighten the jack screw of this connector to secure connector to control.3. Position Cat Monitoring System Control in plate; place bezel over face of control; secure bezel to plate using four screws.4. Check that the proper "code harness" is connected to this same harness. To do so, scroll to mode 1 in this control. The following codes should appear based upon the truck setup. If the proper code does not appear, then the harness code plug is incorrectly configured and it will be necessary to rework the code plug to reflect only continuity between the contacts specified. Using improper coding will result in service hours being displayed incorrectly for Fan usage and/or false diagnostics.793B VIMS rear axle cooling - w/o Fan - 33 (131-5098 Harness - Contacts 2, 3, 4, 5, 7 are all connected)793B VIMS rear axle cooling - with Fan - 34 (126-4495 Harness - Contacts 1, 3, 4, 5, 7 are all connected)On EMS Trucks:
The Cat Monitoring System Control mounts on the right portion of the dash in the cab. You will find at this position:1 - 100-5566 Bezel4 - 7Y-7256 Screw
1. Remove the four screws and bezel from the plate.2. A 40-pin Deutsch DRC connector can be found nearby which must be connected to this Cat Monitoring System Control; tighten the jack screw of this connector to secure connector to the control.3. Position Cat Monitoring System Control in dash; place bezel over face of the control; secure bezel to plate using four screws.4. Check that the proper "code harness" is connected to this same harness. To do so, scroll to mode 1 in this control. The following code should appear based upon the truck setup. If the proper code does not appear, then the harness code plug is incorrectly configured and it will be necessary to rework the code plug to reflect only continuity between the contacts specified. Using improper coding will result in hours being displayed incorrectly for Fan usage and/or false diagnostics.793B EMS rear axle cooling - w/o Fan - 17 (131-5103 Harness - Contacts 2, 3, 4, 6, 7 are all connected)793B EMS rear axle cooling - with Fan- 18 (130-5488 Harness - Contacts 1, 3, 4, 6, 7 are all connected)Chart 3 lists the 793B
Trucks shipped without rear axle oil cooling as monitored with the new 130-1643 Control Group (Cat Monitoring System) should already be reworked by this writing and includes the rear axle filter group on 793B Trucks. The harness codes need to be verified as early production trucks with Rear Axle Pressure Lube & Filter System may have been incorrect.
Again, this update must be complete before the listed configurations can be used.
PROCEDURE:
On VIMS Trucks:
In the rear of the cab, you will find secured to a plate:1 - 100-5566 Bezel4 - 7Y-7256 Screw
1. Remove the four screws and bezel from the plate.2. A 40-pin Deutsch DRC connector can be found nearby which must be connected to this Cat Monitoring System Control; tighten the jack screw of this connector to secure connector to control.3. Position Cat Monitoring System Control in plate; place bezel over face of control; secure bezel to plate using four screws.4. Check that the proper "code harness" is connected to this same harness. To do so, scroll to mode 1 in this control. The following codes should appear based upon the truck setup. If the proper code does not appear, then the harness code plug is incorrectly configured and it will be necessary to rework the code plug to reflect only continuity between the contacts specified. Using improper coding will result in service hours being displayed incorrectly for Fan usage and/or false diagnostics.793B VIMS rear axle cooling - w/o Fan - 33 (131-5098 Harness - Contacts 2, 3, 4, 5, 7 are all connected)793B VIMS rear axle cooling - with Fan - 34 (126-4495 Harness - Contacts 1, 3, 4, 5, 7 are all connected)On EMS Trucks:
The Cat Monitoring System Control mounts on the right portion of the dash in the cab. You will find at this position:1 - 100-5566 Bezel4 - 7Y-7256 Screw
1. Remove the four screws and bezel from the plate.2. A 40-pin Deutsch DRC connector can be found nearby which must be connected to this Cat Monitoring System Control; tighten the jack screw of this connector to secure connector to the control.3. Position Cat Monitoring System Control in dash; place bezel over face of the control; secure bezel to plate using four screws.4. Check that the proper "code harness" is connected to this same harness. To do so, scroll to mode 1 in this control. The following code should appear based upon the truck setup. If the proper code does not appear, then the harness code plug is incorrectly configured and it will be necessary to rework the code plug to reflect only continuity between the contacts specified. Using improper coding will result in hours being displayed incorrectly for Fan usage and/or false diagnostics.793B EMS rear axle cooling - w/o Fan - 17 (131-5103 Harness - Contacts 2, 3, 4, 6, 7 are all connected)793B EMS rear axle cooling - with Fan- 18 (130-5488 Harness - Contacts 1, 3, 4, 6, 7 are all connected)Chart 3 lists the 793B
Parts seal Caterpillar catalog:
9X7375
SEAL-0-RING
Caterpillar
Caterpillar
9X7355
SEAL-LIP TYPE
Caterpillar
Caterpillar
9X7351
SEAL
Caterpillar
Caterpillar
9X7343
SEAL
Caterpillar
Caterpillar
9X7303
SEAL-U-CUP
Caterpillar
Caterpillar
9X7302
SEAL-U-CUP
Caterpillar
Caterpillar
9X7524
SEAL
Caterpillar
Caterpillar
9X7520
SEAL
Caterpillar
Caterpillar
9X7517
SEAL
Caterpillar
Caterpillar
9X7451
SEAL ASSEMBLY
Caterpillar
Caterpillar
9X7445
SEAL AS
Caterpillar
Caterpillar
9X7427
SEAL-LIP
Caterpillar
Caterpillar