AVSPARE.COM
parts catalog

SEAL-LIP TYPE 9X7702 - Caterpillar


9X7702 SEAL-LIP TYPE Caterpillar parts 24H, 24M, 5110B
Rating:
84
Alternative (cross code) number:
CA9X7702
9X-7702
9X7702
Caterpillar 9X7702 SEAL-LIP TYPE
Weight: 0.30 pounds 0 kg.
Information:
AXIAL WIDTH  8  mm
BORE DIAMETER  224  mm
MATERIAL  Polyurethane - 90 Duro 
SEAL OD  224.2  mm
SHAFT OD  199.85  mm

Buy SEAL-LIP TYPE 9X7702 Caterpillar genuine, new aftermarket tractor parts with delivery
MINING EXCAVATOR, MOTOR GRADER,

Compatible equipment models: 9X7702:

MINING EXCAVATOR  5110B  
MOTOR GRADER  24H   24M   Caterpillar
Number on catalog scheme: 8
  For full view, you need register

Information:

Quality and Contamination
Table 12
Description
(1) Do the current methods and procedures comply with the procedures outlined in the Undercarriage Reconditioning Bulletins and Wall Charts?
(2) Are the disassembled components protected from contamination of dirt or debris?
(3) Is the general condition of the work area clean and orderly?
(4) Is any welding or grinding separated from the Disassembly and Assembly area?
(5) Are the work benches neat and clean?
(6) Do all the components being reconditioned meet the specifications that are outlined in the Undercarriage Reconditioning Bulletins?
(7) Are periodic inspections performed during the pin and bushing turn in a sealed and lubricated track link assembly?
(8) Is the track cleaned with high-pressure water before disassembly?
(9) Are the track pins and bushings marked and numbered prior to disassembly?
(10) Is the track press and contact tooling properly setup to ensure correct alignment and assembly dimensions?
(11) Is the link counterbore cleaned with a high-speed rotary wire brush?
(12) Do the pin and bushing projections equal the correct dimensions for the link assembly being rebuilt?
(13) Is the end play allowance on each assembled joint held to 0.03 mm to 0.20 mm (0.001 inch to 0.008 inch) for a wet turn?
(14) Is the track pin and bushing rotated horizontally by 180 degrees? Is the bushing rotated around the track pin by 180 degrees to achieve a correct pin and bushing turn?
(15) Is the proper assembly force being set and maintained on the track press?
(16) Is a pressure test performed on each track joint prior to lubrication?
Comments:
Literature and Materials
Table 13
Description
(1) Is Undercarriage Reconditioning Guide, SEBF8599 current and complete?
(2) Is Servicing Handbook, PEKP9400, "Custom Track Service Handbook" current and available to the track press operator?
(3) Is Parts Sales Kit, PECP3003 current and available to the track press operator?
(4) Is the track press operator or supervisor maintaining a Track Service Logbook? (Other methods include service report, track form, and so forth)
(5) Is the media listed in the "References" section current and available?
Comments:
Recommendations
Table 14
Notes
Table 15

Caterpillar parts catalog:

Caterpillar parts catalog
24 Motor Grader N9Z00001-UP (MACHINE) POWERED BY C27 Engine
24 Motor Grader E9Z00001-UP (MACHINE) POWERED BY C27 Engine
24H Motor Grader 7KK00001-UP (MACHINE) POWERED BY 3412E Engine
24M Motor Grader B9K00001-UP (MACHINE) POWERED BY C18 Engine
24M Motor Grader B9300001-UP (MACHINE) POWERED BY C18 Engine
5110B Excavator AAA00001-UP (MACHINE) POWERED BY 3412E Engine
5110B L Excavator AAK00001-UP (MACHINE) POWERED BY 3412E Engine
5110B MH Excavator AAT00001-UP (MACHINE) POWERED BY 3412E Engine


Parts seal Caterpillar catalog:

9T8059 SEAL
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
0536950 SEAL
24H, AP-800C, AP-800D, BG-225B, CB-224C, CB-334D, CB-335D, CB-434B, CB-434C, CB-534B, CB-534C, CB-544, CB-545, CB-634C, CP-433C, CP-563, CS-431C, CS-433C, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, ...
0951728 SEAL-O-RING
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385...
2227001 SEAL AS
5110B, CB-414, D10N, D10R, D10T, D10T2
1672496 SEAL-WIPER
365C, 375 L, 385B, 385C, 385C L, 5110B
4J9964 SEAL
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...
8J2330 SEAL
120G, 120H, 120H ES, 120H NA, 12E, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 24H
1731007 SEAL
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
1010509 SEAL-INTEGRAL
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H
2227001 SEAL AS
5110B, CB-414, D10N, D10R, D10T, D10T2
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.