3404929 SEAT GP-SUSPENSION Caterpillar parts
CB-434D, CB-534D, CB-54, CB-564D, CB-64, CD-54
Rating:
Alternative (cross code) number:
CA3404929
340-4929
3404929
CA3404929
340-4929
3404929
VIBRATORY COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Sunsong 3404929 Power Steering Reservoir Hose
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit
Sunsong 3404929 Power Steering Reservoir Hose
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit
Sunsong 3404929 Power Steering Reservoir Hose
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit
Sunsong Return Hoses exceed original equipment performance standards (SAE J189) with a max working pressure of 250 psi and are suitable for low pressure high temperature operations || All tubing is manufactured from high grade steel, with zinc electroplate coating, providing corrosion and rust resistance against elements such as moisture and acidity. || Each hose is precision engineered to exact form, fit and function as required for to ensure that all wearable parts are restored to original condition || Hoses are made from reinforced rubber with a synthetic rubber coating that is highly resistant to oil, ozone, and heat. Hoses have an operating temperature of -40 to 350 degrees Fahrenheit
Number on catalog scheme:
For full view, you need register
Compatible equipment models: 3404929:
Information:
1. Remove four bolts (1) and the washers from the rocker shaft assembly.2. Remove rocker shaft assembly (3) from the cylinder head assembly.3. Remove push rods (2) from the engine. Put identification marks on the push rods as to their location in the engine.Install Rocker Shaft Assembly And Push Rods
1. Install push rods (4) in their original location in the cylinder block, and in the valve lifters.
Loosen adjusting screws (2) used to set the valve clearance. This will prevent a bent valve or push rod during installation.
Make sure the O-ring seal in the rear rocker arm support bracket is not damaged when the rear bolt is installed in the support bracket.2. Install a new O-ring seal in the rear rocker arm support bracket. Put 2P2506 Thread Lubricant on all of the bolts that hold the rocker shaft assembly in position except for the bolt that goes through the rear rocker arm support bracket.3. Put rocker shaft assembly (3) in position on the engine. Make sure the dowels located in the support brackets are in alignment with the dowel holes in the cylinder head assembly. Make sure the rocker arms are engaged with the push rods.4. Install four bolts (1) and washers that hold the rocker shaft assembly in position, and tighten them until they are finger tight. 5. Tighten the bolts that hold the rocker shaft assembly as follows:a. Tighten the bolts in number sequence to a torque of 155 N m (115 lb.ft.).b. Tighten the bolts in number sequence to a torque of 250 17 N m (185 13 lb.ft.).c. Tighten the bolts in number sequence to a torque (hand torque only) to 250 17 N m (185 13 lb.ft.). 6. The assembled length of springs (5) at both ends of the rocker shaft assembly must be 1.50 0.25 mm (.059 .010 in.). Remove or install the washers behind the springs to obtain the correct assembled length of the springs.7. Make an adjustment to the valves until the intake valve clearance is 0.38 mm (.015 in.) and the exhaust valve clearance is 0.64 mm (.025 in.). Tighten the nuts on adjustment screws (2) to a torque of 29 7 N m (21 5 lb.ft.). For the complete valve adjustment procedure, see Valve Clearance in Testing And Adjusting.End By:a. install valve cover
1. Install push rods (4) in their original location in the cylinder block, and in the valve lifters.
Loosen adjusting screws (2) used to set the valve clearance. This will prevent a bent valve or push rod during installation.
Make sure the O-ring seal in the rear rocker arm support bracket is not damaged when the rear bolt is installed in the support bracket.2. Install a new O-ring seal in the rear rocker arm support bracket. Put 2P2506 Thread Lubricant on all of the bolts that hold the rocker shaft assembly in position except for the bolt that goes through the rear rocker arm support bracket.3. Put rocker shaft assembly (3) in position on the engine. Make sure the dowels located in the support brackets are in alignment with the dowel holes in the cylinder head assembly. Make sure the rocker arms are engaged with the push rods.4. Install four bolts (1) and washers that hold the rocker shaft assembly in position, and tighten them until they are finger tight. 5. Tighten the bolts that hold the rocker shaft assembly as follows:a. Tighten the bolts in number sequence to a torque of 155 N m (115 lb.ft.).b. Tighten the bolts in number sequence to a torque of 250 17 N m (185 13 lb.ft.).c. Tighten the bolts in number sequence to a torque (hand torque only) to 250 17 N m (185 13 lb.ft.). 6. The assembled length of springs (5) at both ends of the rocker shaft assembly must be 1.50 0.25 mm (.059 .010 in.). Remove or install the washers behind the springs to obtain the correct assembled length of the springs.7. Make an adjustment to the valves until the intake valve clearance is 0.38 mm (.015 in.) and the exhaust valve clearance is 0.64 mm (.025 in.). Tighten the nuts on adjustment screws (2) to a torque of 29 7 N m (21 5 lb.ft.). For the complete valve adjustment procedure, see Valve Clearance in Testing And Adjusting.End By:a. install valve cover
Caterpillar SIS machinery equipment:
Caterpillar SIS
CB-534D CB-534DXW Vibratory Compactor EAA00001-UP (MACHINE) POWERED BY 3054C Engine »
340-4929
SEAT GP-SUSPENSION
CB-434D CB-434DXW Vibratory Compactor CNH00001-UP (MACHINE) POWERED BY 3054C Engine »
340-4929
SEAT GP-SUSPENSION
CB-564D Vibratory Compactor C6D00001-UP (MACHINE) POWERED BY 3054C Engine »
340-4929
SEAT GP-SUSPENSION
CB534D CB534D XW Vibratory Compactor B5M00001-UP (MACHINE) POWERED BY 3054C Engine »
340-4929
SEAT GP-SUSPENSION
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine »
340-4929
SEAT GP-SUSPENSION
CD54 Vibratory Compactor J5R00001-UP (MACHINE) POWERED BY 3054C Engine »
340-4929
SEAT GP-SUSPENSION
CB-534D CB-534DXW Vibratory Compactor FEA00001-UP (MACHINE) POWERED BY 3054C Engine »
340-4929
SEAT GP-SUSPENSION
CB54 Vibratory Compactor JLM00001-UP (MACHINE) POWERED BY C4.4 Engine »
340-4929
SEAT GP-SUSPENSION
CB64 Vibratory Compactor DJM00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine »
340-4929
SEAT GP-SUSPENSION
CB54 Compactor K3J00001-UP (MACHINE) POWERED BY C4.4 Engine »
340-4929
SEAT GP-SUSPENSION
CB64 Compactor CB500001-UP (MACHINE) POWERED BY C4.4 Engine »
340-4929
SEAT GP-SUSPENSION
CS12 Vibratory Soil Compactor GCS00001-UP (MACHINE) POWERED BY C4.4 Engine »
340-4929
SEAT GP-SUSPENSION
CS11 Vibratory Soil Compactor RK800001-UP (MACHINE) POWERED BY C4.4 Engine »
340-4929
SEAT GP-SUSPENSION
CS10 Vibratory Soil Compactor T8F00001-UP (MACHINE) POWERED BY C4.4 Engine »
340-4929
SEAT GP-SUSPENSION
Caterpillar parts catalog:
Parts seat Caterpillar catalog:
1916162
SEAT GP-SUSPENSION
CB-434D, CB-534D, CB-564D, CD-54
CB-434D, CB-534D, CB-564D, CD-54
3404931
SEAT GP-SUSPENSION
CB-434D, CB-534D, CB-564D
CB-434D, CB-534D, CB-564D
1915351
SEAT GP-SUSPENSION
CB-434D, CB-534D, CB-54, CB-564D, CB-634D, CB-64, CD-54
CB-434D, CB-534D, CB-54, CB-564D, CB-634D, CB-64, CD-54
3906849
SEAT GP-SUSPENSION
CB-434D, CB-534D, CB-54, CB-564D, CB-64, CD-54
CB-434D, CB-534D, CB-54, CB-564D, CB-64, CD-54
3906850
SEAT GP-SUSPENSION
CB-434D, CB-534D, CB-564D
CB-434D, CB-534D, CB-564D
2306367
SEAT BELT GP
AP-1055D, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, CB-434B, CB-434C, CB-434D, CB-534D, CB-54, CB-564D, CB-634D, CB-64, CD-54, C...
AP-1055D, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, CB-434B, CB-434C, CB-434D, CB-534D, CB-54, CB-564D, CB-634D, CB-64, CD-54, C...
3706865
SEAT GP-SUSPENSION
CB-434D, CB-534D, CB-54, CB-564D, CB-64, CD-54
CB-434D, CB-534D, CB-54, CB-564D, CB-64, CD-54
3706866
SEAT GP
CB-434D, CB-534D, CB-564D
CB-434D, CB-534D, CB-564D
5G5490
SEAT & SUPPORT GP
D3B, D3C
D3B, D3C
3456319
SEAT AR-SUSPENSION
236D, 242D, 246D, 257D, 259D, 262D, 272D, 277D, 279D, 287D, 289D, 299D
236D, 242D, 246D, 257D, 259D, 262D, 272D, 277D, 279D, 287D, 289D, 299D
1346520
SEAT GP-SUSPENSION
517, 527, 572R, 572R II, 583R
517, 527, 572R, 572R II, 583R
3621768
SEAT GP-SUSPENSION
769D, 771D, 773D, 773E, 775D, 777D, 784C, 785C, 793B, 793C
769D, 771D, 773D, 773E, 775D, 777D, 784C, 785C, 793B, 793C
2301389
SEAT GP-SUSPENSION
621G, 623G, 627G, 631G, 637G, 657G
621G, 623G, 627G, 631G, 637G, 657G
2679433
SEAT GP-SUSPENSION
924G, 938G II, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT28G, IT38G II, IT62H
924G, 938G II, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT28G, IT38G II, IT62H
3456055
SEAT & MOUNTING GP
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
2584055
SEAT GP-SUSPENSION
246C, 256C, 262C, 262C2, 272C, 272D, 272D XHP, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 299D, 299D XHP
246C, 256C, 262C, 262C2, 272C, 272D, 272D XHP, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 299D, 299D XHP
2493237
SEAT GP-SUSPENSION
CP-44, CP-56, CP-64, CP-76, CS-44, CS-54, CS-64, CS-74
CP-44, CP-56, CP-64, CP-76, CS-44, CS-54, CS-64, CS-74
4328930
SEAT GP-SUSPENSION
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
236D, 242D, 246D, 257D, 259D, 262D, 272D, 272D XHP, 277D, 279D, 287D, 289D, 299D, 299D XHP
2621331
SEAT & MOUNTING GP
CP-44, CP-56, CP-64, CP-76, CS-44, CS-54, CS-64, CS-74
CP-44, CP-56, CP-64, CP-76, CS-44, CS-54, CS-64, CS-74
2621330
SEAT & MOUNTING GP
CP-44, CP-56, CP-64, CP-76, CS-44, CS-54, CS-64, CS-74
CP-44, CP-56, CP-64, CP-76, CS-44, CS-54, CS-64, CS-74