9T-3096 VALVE GP-CHECK -DEAD ENGINE LOWER PART OF 219-5140 LINES GP-PILOT 826G II LANDFILL COMPACTOR

Pos.	Part No	Qty	Parts name
1.	4V-8256	[4]	SPRING
2.	117-4492	[1]	ROD
3.	136-1544	[1]	LATCH AS-LH
4.	156-5545	[1]	LATCH AS-RH
5.	164-4531	[1]	ROD
6.	170-1112	[1]	PLATE AS
7.	170-1114	[1]	HANDLE (SLIDE ADJUSTMENT)
8.	170-1115	[1]	HANDLE (TILT ADJUSTMENT)
9.	132-0338	[2]	WASHER-PLASTIC
10.	2K-4973	[2]	LOCKNUT (3/8-16 THD)
11.	7X-0608	[2]	WASHER-HARD (10.2X16X2.0MM THK)

#SEBC13660042

187-3675: AIR CONDITIONER AR

AIR CONDITIONER AR

187-3675 AIR CONDITIONER AR
PART OF 219-5156 CAB AR-ENCLOSED ROPS

i01305219 SEBC1366

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9X-8117	[2]	TUBE AS
2.	115-0627 Y	[1]	AIR CONDITIONER GP
3.	131-1270 Y	[1]	LINES GP-HEATER
4.	131-1274 Y	[1]	LINES GP-AIR CONDITIONER
5.	9X-2040 M	[4]	SCREW-TRUSS HEAD (M10X1.5X25MM)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBC13660043

115-0627: AIR CONDITIONER GP

AIR CONDITIONER GP

115-0627 AIR CONDITIONER GP
PART OF 187-3675 AIR CONDITIONER AR

i00574048 SEBC1366

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	2V-3216 C	[1]	CLIP
2.	3B-4501	[2]	LOCKWASHER (#8)
3.	3E-0400	[2]	WHEEL-BLOWER
4.	3E-5464	[1]	SWITCH AS-THERMOSTAT (REFRIGERANT)
5.	174-1494	[1]	MOTOR GP-ELECTRIC (27 VOLT)
	3E-3365	[1]	WEDGE-RECEPTACLE LOCK (2 PIN)
	9W-0852	[2]	PIN-CONNECTOR
	102-8802	[1]	KIT-RECEPTACLE (2 PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
6.	3S-2093	[4]	STRAP-CABLE
7.	5C-9553 CM	[19]	BOLT (M6X1X16MM)
8.	9X-2488 C	[2]	CLAMP-HOSE
9.	5P-4115	[5]	WASHER-HARD (7.2X19X2MM THK)
10.	6V-1668	[2]	WASHER (6.5X29.1X3MM THK)
11.	6V-7646	[1]	WASHER-HARD (7.2X25X2MM THK)
12.	8C-3756	[1]	FILM-IDENTIFICATION (GROUP & SEQUENCE NO.)
13.	8C-4586	[2]	CLAMP
14.	6V-7728 M	[1]	BOLT (M6X1.0X45MM)
15.	8P-5141	[2]	PLATE-ORIFICE
16.	8T-0337 M	[3]	SCREW-MACHINE (M4X0.7X12MM)
17.	8T-4205	[30]	WASHER-HARD (7.2X14.5X2MM THK)
18.	8T-6631	[2]	SCREW-MACHINE (8-32X0.5 IN)
19.	9G-1950	[1]	RESISTOR
20.	9M-8406 C	[2]	CLIP
21.	9X-2185	[4]	SCREW (8-15X0.44 IN)
22.	9X-8498 M	[1]	BOLT (M6X1.0X180MM)
23.	068-8993	[1]	GROMMET
24.	113-8113	[1]	ROD
25.	126-5606	[1]	COIL AS-EVAPORATOR
26.	126-5607	[1]	COIL AS-HEATER
27.	126-5608	[1]	HOUSING AS
28.	126-5609	[1]	PLATE AS
29.	211-9047	[1]	VALVE AS-WATER
30.	220-1828	[1]	MOTOR-ACTUATOR
31.	126-5612	[1]	HARNESS AS-HEATER & AIR COND
	8T-8737	[4]	PLUG-SEAL
	102-8801	[1]	KIT-RECEPTACLE (12 PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	155-2255	[1]	KIT-CONNECTING PLUG (12 PIN)
	155-2270	[2]	KIT-CONNECTING PLUG (2 PIN)
			(TO BLOWER MOTOR & WATER VALVE MOTOR)
	155-2274	[1]	KIT-CONNECTING PLUG (6 PIN)
			(EACH KIT INCLUDES PLUG AS & WEDGE)
32.	126-6006	[1]	DOOR AS
33.	126-6009	[1]	COVER
34.	126-6010	[1]	CONTROL AS
35.	127-6422	[1]	PLATE AS
36.	127-6423	[1]	PLATE
37.	129-3178 M	[12]	LOCKNUT (M6X1 THD)
38.	130-1888	[1]	GASKET
39.	130-1890	[6]	GASKET
40.	131-0820	[1]	GASKET
41.	131-0821	[1]	GASKET
42.	131-0822	[1]	GASKET
43.	131-3093	[1]	BUSHING
44.	126-8472 E	[2]	SEAL (38.1CM EACH)
45.	136-1953 BCE		HOSE
46.	4F-2320	[3]	WASHER
47.	8T-4138 CM	[2]	BOLT (M6X1X20MM)
48.	6V-2496 BD		SEAL
49.	5P-5908 BD		SEAL
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER
	M		METRIC PART

#SEBC13660044

219-5156: CAB AR-ENCLOSED ROPS

CAB AR-ENCLOSED ROPS

219-5156 CAB AR-ENCLOSED ROPS -CUSTOM
PART OF 219-5157 OPERATOR AR

i01880528 SEBC1366

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Part No	Qty	Parts name
Y	[1]	AIR CONDITIONER AR
160-5003	[1]	BRACKET AS
207-7875 Y	[1]	CONDENSER & MTG GP-REFRIGERANT
214-4796 Y	[1]	CONTROL GP-ELECTROHYDRAULIC (JOYSTICK, SINGLE FUNCTION)
169-8257 Y	[1]	CONTROL GP-FOOT BRAKE
109-8193 Y	[1]	CONTROL GP-PARKING BRAKE
141-4940 Y	[1]	CONTROL GP-STEERING (STIC)
4E-8413 Y	[1]	CONTROL GP-STIC
164-4237 Y	[1]	COVER GP-DASH
219-5082 Y	[1]	DUCT & FILTER GP-AIR
187-3689 Y	[1]	INSTALLATION GP-RADIO
198-8845 Y	[1]	LIGHTING GP-FLOOD
201-9755 Y	[1]	LINER GP-CAB
187-0738 Y	[1]	LOCK GP-STIC CONTROL
187-3683 Y	[1]	PANEL GP-INSTRUMENT (UPPER)
219-5081 Y	[1]	PANEL GP-INSTRUMENT (LOWER)
141-4645 Y	[1]	PEDAL GP-GOVERNOR
187-3685 Y	[1]	ROPS GP-ENCLOSED
117-1410 Y	[1]	SEALING GP-GLASS
200-3174 Y	[1]	SEAT GP-SUSPENSION
219-5086 Y	[1]	SUPPORT GP-HYDRAULIC CONTROL
173-1905 Y	[1]	SUPPORT GP-SEAT
171-3897 Y	[1]	SUPPORT GP-STEERING CONTROL
Y	[1]	SUPPRESSION GP-SOUND
109-8196 Y	[1]	WIPER GP-WINDOW
Y	[1]	WIRING GP-CAB

		***STANDARD REMOVAL***
192-3277 J	[1]	BRACKET AS
J		PART OF STANDARD ROPS GP-ENCLOSED
Y		SEPARATE ILLUSTRATION

#SEBC13660045

207-7875: CONDENSER & MTG GP-REFRIGERANT

CONDENSER & MTG GP-REFRIGERANT

207-7875 CONDENSER & MTG GP-REFRIGERANT
PART OF 219-5156 CAB AR-ENCLOSED ROPS

i01871142 SEBC1366

2077875 CONDENSER & MTG GP-REFRIGERANT Parts scheme

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	8D-3932	[4]	MOUNTING
2.	103-9527 Y	[1]	CONDENSER GP-REFRIGERANT
3.	107-3157	[8]	WASHER (22X76.2X6MM THK)
4.	117-8996	[1]	PLATE
5.	134-0165	[4]	WASHER (13.8X45X3MM THK)
6.	174-2407	[1]	INSULATION
7.	174-2408	[1]	INSULATION
8.	179-5562	[4]	SPACER
9.	199-5510	[1]	ROOF
10.	207-4648	[1]	BRACKET AS (RH)
	8T-3597 M	[2]	NUT-WELD (M12X1.75 THD)
11.	207-4653	[1]	BRACKET AS (LH)
	8T-3490 M	[1]	NUT-WELD (M10X1.5 THD)
	8T-3597 M	[2]	NUT-WELD (M12X1.75 THD)
12.	093-2064	[4]	GROMMET
13.	7X-0515	[4]	WASHER-HARD (17X35X5MM THK)
14.	8T-4140 M	[4]	BOLT (M16X2X60MM)
15.	8T-4194 M	[4]	BOLT (M12X1.75X50MM)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBC13660046

103-9527: CONDENSER GP-REFRIGERANT

CONDENSER GP-REFRIGERANT

103-9527 CONDENSER GP-REFRIGERANT
PART OF 207-7875 CONDENSER & MTG GP-REFRIGERANT

i01080207 SEBC1366

1039527 CONDENSER GP-REFRIGERANT Parts scheme

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-5239	[1]	RELAY AS (24 VOLT)(CONDENSER BLOWER MOTOR)
2.	3S-2093	[7]	STRAP-CABLE
3.	7K-1181 C	[2]	STRAP-CABLE
4.	7T-5856	[4]	CLAMP
5.	8C-3756	[1]	FILM-IDENTIFICATION (GROUP & SEQUENCE NO.)(REFRIGERANT CONDENSER)
6.	8P-6363	[1]	PLUG
7.	9X-3452	[2]	GUARD AS-FAN
8.	124-8490 C	[1]	HARNESS AS (CONDENSER BLOWER MOTORS)
	155-2270	[1]	KIT-CONNECTING PLUG (2 PIN)
			(INCLUDES PLUG AS & WEDGE)
	102-8803	[1]	KIT-RECEPTACLE (3 PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	9X-1054	[1]	PLUG AS-CONNECTOR (4 PIN)
9.	142-8620	[2]	FAN AS
10.	174-1495	[2]	MOTOR GP-ELECTRIC (CONDENSER BLOWER)
			(EACH INCLUDES)
	3E-3365	[1]	WEDGE-RECEPTACLE LOCK (2 PIN)
	9W-0852	[2]	PIN-CONNECTOR
	102-8802	[1]	KIT-RECEPTACLE (2 PIN)
			(INCLUDES WEDGE & RECEPTACLE AS)
11.	203-2070 C	[8]	MOUNT
12.	204-9530 C	[4]	TUBE
13.	204-9531 C	[1]	COIL-CONDENSER
14.	204-9532 C	[1]	CASE AS
	8T-3490 M	[12]	NUT-WELD (M10X1.5 THD)
	9G-9151	[2]	CLIP
	7T-1099	[4]	LINK
	8T-3597 M	[12]	NUT-WELD (M12X1.75 THD)
15.	4P-8134 C	[2]	CLIP
16.	5C-2890 M	[1]	NUT (M6X1 THD)
17.	5P-1075	[8]	WASHER-HARD (10.2X22.5X3MM THK)
18.	5P-8441	[1]	GROMMET
19.	7X-0578	[4]	WASHER-HARD (10.2X32X2.5MM THK)
20.	8T-4121 C	[4]	WASHER-HARD (11X21X2.5MM THK)
21.	8T-4133 M	[4]	NUT (M10X1.5 THD)
22.	8T-4137 M	[8]	BOLT (M10X1.5X20MM)
23.	8T-4192 M	[12]	BOLT (M12X1.75X25MM)
24.	8T-4205	[1]	WASHER-HARD (7.2X14.5X2MM THK)
25.	8T-4223	[12]	WASHER-HARD (13.5X25.5X3MM THK)
26.	8T-6685 CM	[4]	BOLT (M10X1.50X110MM)
27.	9X-7373	[1]	GROMMET
28.	5P-5924 BD		SEAL (.9DM EACH)
29.	5P-5672 BCD		SEAL (5.64DM EACH)
30.	5P-5908 BD		SEAL (1.10DM EACH)
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	D		ORDER BY THE METER
	M		METRIC PART

#SEBC13660047

154-7443: CONTROL GP-MONITOR

CONTROL GP-MONITOR

154-7443 CONTROL GP-MONITOR
CATERPILLAR MONITORING SYSTEM
PART OF 219-5081 PANEL GP-INSTRUMENT

i01028554 SEBC1366

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name	Comments
			(NO SERVICED PARTS)

#SEBC13660048

103-5526: CONTROL GP-MONITOR SYS DIMMER

CONTROL GP-MONITOR SYS DIMMER

103-5526 CONTROL GP-MONITOR SYS DIMMER
PART OF 187-3683 PANEL GP-INSTRUMENT

i00089832 SEBC1366

1035526 CONTROL GP-MONITOR SYS DIMMER Parts scheme

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	5P-9132	[2]	SCREW-WASHER HEAD (HEX)(6-32X.19 IN)
2.	3E-3383 J	[1]	WEDGE-RECEPTACLE LOCK
3.	186-3735	[6]	PIN-CONNECTOR

			AVAILABLE REPAIR KIT(S):
	102-8805 J	[1]	KIT-RECEPTACLE (6 PIN)
			(INCLUDES RECEPTACLE AS & PART MARKED J)
	J		KIT MARKED J INCLUDES PART MARKED J

#SEBC13660049

164-4237: COVER GP-DASH

COVER GP-DASH

164-4237 COVER GP-DASH
STIC STEERING
PART OF 219-5156 CAB AR-ENCLOSED ROPS

i01573201 SEBC1366

For full view, you need register

Parts for your 826G II LANDFILL COMPACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	6V-2491	[24]	RIVET-POP
2.	129-7184	[1]	FILM-INSTRUCTION (ENGINE RUN, ON/OFF)
3.	203-7143 C	[1]	PLATE AS
4.	173-5791	[1]	COVER
5.	9X-2042 M	[14]	SCREW-TRUSS HEAD (M6X1X12MM)
6.	9X-2045 M	[2]	SCREW-TRUSS HEAD (M6X1X20MM)
7.	5C-2890 CM	[2]	NUT (M6X1 THD)
8.	9X-8256 C	[2]	WASHER (6.6X12X2MM THK)
9.	203-6481 C	[1]	PLATE AS
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART

Information:

HYDRAULIC SYSTEM

VALVE GP-CHECK

Specifications

Check Valve (Dead Engine Lower)
824G Series II Wheel Tractor, 825G Series II Soil Compactor and 826G Series II Landfill Compactor Electrohydraulic System