AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

613B TRACTOR 38W00001-UP (MACHINE) POWERED BY 3208 ENGINE BASIC ENGINE Caterpillar SIS



WHEEL TRACTOR 613B WHEEL TRACTOR 38W
 613B TRACTOR 38W00001-UP (MACHINE) POWERED BY 3208 ENGINE SEBP1071 613B 38W   (1976)

Parts group 613B:

  For full view, you need register
BASIC ENGINE
AIR COMPRESSOR GP
COMPRESSOR GP
6N-3709 COMPRESSOR GP
6N3709 AIR COMPRESSOR GROUP--Type 1
4N7634 Air Compressor parts are shown on Pages 32 & 32A
COMPRESSOR GP
6N-3709 COMPRESSOR GP
6N3709 AIR COMPRESSOR GROUP--Type 2
4N7634 Air Compressor parts are shown on Page 32
AIR COMPRESSOR GP
4N-7634 AIR COMPRESSOR GP
4N7634 AIR COMPRESSOR GROUP--Type 1
Part of 6N3709 Air Compressor Group shown on Page 31
AIR COMPRESSOR GP
4N-7634 AIR COMPRESSOR GP
4N7634 AIR COMPRESSOR GROUP--Type 2
Part of 6N3709 Air Compressor Group shown on Page 31
BELT TIGHTENER GP
PULLEY GP-IDLER
6N-3692 PULLEY GP-IDLER
6N3692 IDLER PULLEY GROUP
CAMSHAFT GP
CAMSHAFT GP-SINGLE
9N-0728 CAMSHAFT GP-SINGLE
9N728 CAMSHAFT GROUP
CRANKSHAFT GP
CRANKSHAFT GP
9N-2133 CRANKSHAFT GP
9N2133 CRANKSHAFT GROUP
Engine Serial No. 79V2557 to 79V8034 inclusive
CRANKSHAFT GP
9N-6222 CRANKSHAFT GP
9N6222 CRANKSHAFT GROUP
Engine Serial No. 79V8035 To 79V8281 Inclusive
CRANKSHAFT GP
9N-6222 CRANKSHAFT GP
9N6222 CRANKSHAFT GROUP
Engine Serial No. 79V8282-Up
CRANKSHAFT GP
2W-0085 CRANKSHAFT GP
2W0085 SERVICE CRANKSHAFT GROUP
Field Installation
CRANKSHAFT GP
9N-2017 CRANKSHAFT GP
9N2017 CRANKSHAFT GROUP
Part of 9N2139 and 9N5190 Short Block Group listed on Pages 7 and 7A
SEAL GP-CRANKSHAFT
9N-0542 SEAL GP-CRANKSHAFT
9N542 CRANKSHAFT SEAL GROUP
CRANKSHAFT BEARING REPLACEMENT
CRANKSHAFT BEARING REPLACEMENT
CRANKSHAFT BEARING REPLACEMENT
CYLINDER BLOCK GP
CYLINDER BLOCK GP
9N-3120 CYLINDER BLOCK GP
9N3120 CYLINDER BLOCK GROUP
Engine Serial No. 79V2557 to 79V4883 inclusive
Also part of 9N2139 Short Block Group & 9N1255 Cylinder Block Service Group listed on Pages 7 & 7A
CYLINDER BLOCK GP
9N-3551 CYLINDER BLOCK GP
9N3551 CYLINDER BLOCK GROUP
Engine Serial No. 79V4884 to 79V5313 inclusive
Also part of 9N2139 Short Block Group & 9N1255 Cylinder Block Service Group listed on Pages 7 & 7A
CYLINDER BLOCK GP
9N-3551 CYLINDER BLOCK GP
9N3551 CYLINDER BLOCK GROUP
Engine Serial No. 79V5314 to 79V5380 inclusive
Also part of 9N2139 Short Block Group and 9N1255 Cylinder Block Service Group listed on Pages 7 and 7A
CYLINDER BLOCK GP
9N-3761 CYLINDER BLOCK GP
9N3761 CYLINDER BLOCK GROUP
Engine Serial No. 79V5381 to 79V10269 inclusive
Also part of 9N5190 Short Block Group and 9N3763 Cylinder Block Service Group listed on Pages 7A and 7B
CYLINDER BLOCK GP
9N-3761 CYLINDER BLOCK GP
9N3761 CYLINDER BLOCK GROUP
Engine Serial No. 79V10270-Up
Also part of 9N5190 Short Block Group and 9N3763 Cylinder Block Service Group listed on Pages 7A and 7B
COVER GP-CYLINDER BLOCK
9L-6065 COVER GP-CYLINDER BLOCK
9L6065 CYLINDER BLOCK COVER GROUP
Also part of 9N2139 & 9N5190 Short Block Groups and 9N1255 & 9N3763 Cylinder
Block Service Groups listed on Pages 7, 7A & 7B
9N-2139 BLOCK GP-SHORT
9N2139 SHORT BLOCK GROUP--Field Installation
Replaced by 9N5190 Short Block Group listed on Page 7A
9N-5190 BLOCK GP-SHORT
9N5190 SHORT BLOCK GROUP--Field Installation
9N-1255 CYLINDER BLOCK GP
9N1255 CYLINDER BLOCK SERVICE GROUP
Replaced by 9N3763 Cylinder Block Service Group listed on Page 7B. Provides
Field Replacement for 9N3120 or 9N3551 Cylinder Block Group shown on
Pages 6, 6A and 6B
9N-3763 SERVICE GP-CYLINDER BLOCK
9N3763 CYLINDER BLOCK SERVICE GROUP
Provides Field Replacement for 9N3761 Cylinder Block Group shown on Page 6C
CYLINDER HEAD GP
CYLINDER HEAD GP
9N-1105 CYLINDER HEAD GP
9N1105 CYLINDER HEAD GROUP
Engine Serial No. 79V2557 to 79V4136 inclusive
CYLINDER HEAD GP
9N-1105 CYLINDER HEAD GP
9N1105 CYLINDER HEAD GROUP*R
Engine Serial No. 79V4137 to 79V8713 inclusive
CYLINDER HEAD GP
9N-1105 CYLINDER HEAD GP
9N1105 CYLINDER HEAD GROUP
Engine Serial No. 79V8714 To 79V9369 Inclusive
1W6221--Page 11B.04
CYLINDER HEAD GP
9N-1105 CYLINDER HEAD GP
9N1105 CYLINDER HEAD GROUP
Engine Serial No. 79V9370 To 79V10843 Inclusive
1W4241--Page 11B.05
CYLINDER HEAD GP
9N-1105 CYLINDER HEAD GP
9N1105 CYLINDER HEAD GROUP
Engine Serial No. 79V10844-Up
1W4241--Page 11B.06
CYLINDER HEAD GP
1W-6221 CYLINDER HEAD GP
1W6221 CYLINDER HEAD GROUP
Engine Serial No. 79V8714 To 79V9369 Inclusive
Part Of 9N1105 Cylinder Head
CYLINDER HEAD GP
1W-4241 CYLINDER HEAD GP
1W4241 CYLINDER HEAD GROUP
Engine Serial No. 79V9370 To 79V10843 Inclusive
Part Of 9N1105 Cylinder Head
CYLINDER HEAD GP
1W-4241 CYLINDER HEAD GP
1W4241 CYLINDER HEAD GROUP
Engine Serial No. 79V10844-Up
Part Of 9N1105 Cylinder Head
DRIVE GP-FAN
DRIVE GP-FAN (BELT)
4W-3777 DRIVE GP-FAN (BELT)
4W3777 FAN BELT DRIVE GROUP-FIELD INSTALLATION
FLYWHEEL GP
FLYWHEEL GP
4N-8850 FLYWHEEL GP
4N8850 FLYWHEEL GROUP
GEAR GP
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V2557 to 79V2830 inclusive
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V2831 to 79V2964 inclusive
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V2965 to 79V3016 inclusive
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V3017 to 79V8491 inclusive
HOUSING GP-FRONT
9N-5211 HOUSING GP-FRONT
9N5211 FRONT HOUSING GROUP
Serial No. 79V8492-Up
HOUSING GP-FLYWHEEL
FLYWHEEL HOUSING GROUP
4N-8929 FLYWHEEL HOUSING GROUP
4N8929 FLYWHEEL HOUSING GROUP
Engine Serial No. 79V2557 to 79V3692 inclusive
HOUSING GP-FLYWHEEL
9N-0529 HOUSING GP-FLYWHEEL
9N529 FLYWHEEL HOUSING GROUP
Engine Serial No. 79V3693 to 79V10377 inclusive
HOUSING GP-FLYWHEEL
9N-0529 HOUSING GP-FLYWHEEL
9N0529 FLYWHEEL HOUSING GROUP
Engine Serial No. 79V10378-Up
For Field Replacement Of 9N6298 Order 1W8950--Page 17B.02
HOUSING GP-FLYWHEEL
1W-8950 HOUSING GP-FLYWHEEL
1W8950 FLYWHEEL HOUSING GROUP
Field Replacement For 9N6298
COVER GP-FLYWHEEL HOUSING
6N-0807 COVER GP-FLYWHEEL HOUSING
6N807 FLYWHEEL HOUSING COVER GROUP
Engine Serial No. 79V2557 to 79V7125 inclusive
COVER GP-FLYWHEEL HOUSING
8N-4671 COVER GP-FLYWHEEL HOUSING
8N4671 FLYWHEEL HOUSING COVER GROUP
Engine Serial No. 79V7126-Up
HOUSING GP-FRONT
COVER GP-FRONT HOUSING
9N-0560 COVER GP-FRONT HOUSING
9N560 FRONT HOUSING COVER GROUP
Serial No. 79V2557 to 79V9269 inclusive
COVER GP-FRONT HOUSING
9N-0560 COVER GP-FRONT HOUSING
9N560 FRONT HOUSING COVER GROUP
Serial No. 79V9270-Up
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V2557 to 79V2830 inclusive
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V2831 to 79V2964 inclusive
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V2965 to 79V3016 inclusive
HOUSING GP-FRONT
9N-1080 HOUSING GP-FRONT
9N1080 FRONT HOUSING GROUP
Engine Serial No. 79V3017 to 79V8491 inclusive
HOUSING GP-FRONT
9N-5211 HOUSING GP-FRONT
9N5211 FRONT HOUSING GROUP
Serial No. 79V8492-Up
LIFTING GP-ENGINE
LIFTING GP
9N-0191 LIFTING GP
9N191 LIFTING EYE GROUP--2 Required
MOUNTING GP-ENGINE
SUPPORT GP-ENGINE
9N-0122 SUPPORT GP-ENGINE
9N122 ENGINE SUPPORT GROUP
Engine Serial No. 79V2557 to 79V8491 inclusive
SUPPORT GP-ENGINE
6N-7831 SUPPORT GP-ENGINE
6N7831 SUPPORT GROUP
SUPPORT GP-ENGINE
9N-5224 SUPPORT GP-ENGINE
9N5224 SUPPORT GROUP
Engine Serial No. 79V8492-Up
PAN GP-OIL
PAN GP-OIL
9N-0565 PAN GP-OIL
9N565 OIL PAN GROUP
PISTON & ROD GP
PISTON & ROD GP
9N-0150 PISTON & ROD GP
9N150 CONNECTING ROD AND PISTON GROUP--8 Required
Engine Serial No. 79V2557 to 79V3454 inclusive
Also part of 9N2139 Short Block Group listed on Page 7
PISTON & ROD GP
9N-2613 PISTON & ROD GP
9N2613 CONNECTING ROD AND PISTON GROUP--8 Required
Engine Serial No. 79V3455 to 79V5380 inclusive
Also part of 9N2139 Short Block Group shown on Page 7
PISTON & ROD GP
9N-3538 PISTON & ROD GP
9N3538 CONNECTING ROD AND PISTON GROUP--8 Required
Engine Serial No. 79V5381 to 79V8572 inclusive
Also part of 9N5190 Short Block Group listed on Page 7A
PISTON & ROD GP
9N-6435 PISTON & ROD GP
9N6435 CONNECTING ROD AND PISTON GROUP--8 Required--Type 1
Engine Serial No. 79V8573-Up
Also part of 9N5190 Short Block Group listed on Page 7A
PISTON & ROD GP
9N-6435 PISTON & ROD GP
9N6435 CONNECTING ROD AND PISTON GROUP--8 Required--Type 2
Engine Serial No. 79V8573-Up
PISTON & ROD GP
9N-6435 PISTON & ROD GP
9N6435 CONNECTING ROD AND PISTON GROUP--TYPE 3
Engine Serial No. 79V8573-Up
2W4841--Page 10C
PISTON GP
2W-4841 PISTON GP
2W4841 PISTON GROUP
Engine Serial No. 79V8573-Up
Part Of 9N6435 Connecting Rod And Piston
PULLEY GP
PULLEY GP-IDLER
6N-3692 PULLEY GP-IDLER
6N3692 IDLER PULLEY GROUP
PULLEY GP-AUXILIARY DRIVE
9N-0543 PULLEY GP-AUXILIARY DRIVE
9N543 AUXILIARY DRIVE PULLEY GROUP
Engine Serial No. 79V2557 to 79V8491 inclusive
PULLEY GP-AUXILIARY DRIVE
1N-3855 PULLEY GP-AUXILIARY DRIVE
1N3855 AUXILIARY DRIVE PULLEY GROUP
Engine Serial No. 79V8492-Up
VALVE MECHANISM GP
VALVE MECHANISM GP
9N-0487 VALVE MECHANISM GP
9N0487 VALVE MECHANISM GROUP
Engine Serial No. 79V2557 To 79V7343 Inclusive & 79V11951-Up
VALVE-MECHANISM GP
9N-5780 VALVE-MECHANISM GP
9N5780 VALVE MECHANISM GROUP
Engine Serial No. 79V7344 To 79V11030 Inclusive
VALVE-MECHANISM GP
9N-5780 VALVE-MECHANISM GP
9N5780 VALVE MECHANISM GROUP
Engine Serial No. 79V11031 To 79V11950 Inclusive
1W5719--Page 12A.02
ROCKER ARM GP-VALVE
1W-5719 ROCKER ARM GP-VALVE
1W5719 VALVE ROCKER ARM GROUP
Engine Serial No. 79V11031 To 79V11950 Inclusive
Part Of 9N5780 Valve Mechanism
COVER GP-VALVE MECHANISM
9N-0730 COVER GP-VALVE MECHANISM
9N0730 VALVE MECHANISM COVER GROUP
Engine Serial No. 79V2557 To 79V12440 Inclusive
COVER GP-VALVE MECHANISM
9N-0730 COVER GP-VALVE MECHANISM
9N0730 VALVE MECHANISM COVER GROUP
Engine Serial No. 79V12441-Up
4W6968, 4W6972--Page 12D
COVER GP-VALVE MECHANISM
4W-6968 COVER GP-VALVE MECHANISM
4W6968 VALVE MECHANISM COVER GROUP
Engine Serial No. 79V12441-Up
9L8790--Page 33
COVER GP-VALVE MECHANISM
4W-6972 COVER GP-VALVE MECHANISM
4W6972 VALVE MECHANISM COVER GROUP
Engine Serial No. 79V12441-Up
Part Of 9N0730 Valve Mechanism Cover

Information:

(For parts list, see above)

General Service Information
Tu-Flo 300 Compressor
AIR COMPRESSORS TU-FLO 300, 400, 500, 501, 600, 700 & 1000 C
Tu-Flo 400, 500, 1000 Compressors
AIR COMPRESSORS TU-FLO 300, 400, 500, 501, 600, 700 & 1000 C
Tu-Flo 501 Compressor
AIR COMPRESSORS TU-FLO 300, 400, 500, 501, 600, 700 & 1000 C
Tu-Flo 600 Compressor
AIR COMPRESSORS TU-FLO 300, 400, 500, 501, 600, 700 & 1000 C
Tu-Flo 700 Compressor
AIR COMPRESSORS TU-FLO 300, 400, 500, 501, 600, 700 & 1000 C
Truck Engine News
A New Special Instruction , "Troubleshooting Compressed Air System Components and Performance" Is Available {1803, 5500}
2002/09/01
Special Instruction
Air Compressor Installation Instructions{1803}
Air Compressor Installation Instructions{1803}
Troubleshooting Compressed Air System Components and Performance{1803, 5500}
Troubleshooting Compressed Air System Components and Performance{1803, 5500}
Specifications
Air Compressor
3208 VEHICULAR ENGINE
Air Compressor Governor
613B WHEEL TRACTOR-SCRAPER AIR SYSTEM AND BRAKES
Disassembly and Assembly
Air Compressor Governor
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Air Compressor
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
Air Line For Air Compressor Governor Now Connected To Outlet For Wet Air Tank{4272,1065,4278}
1978/01/30
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
New Idler Pulley Assembly Used In Air Compressor Group {1803}
1990/02/05
A New Special Instruction, REHS1428 , "Troubleshooting Compressed Air System Components and Performance" Is Available {1803, 5500}
2002/09/23
Repair Guidelines for Air Compressors {1803}
2003/08/25
A New Diagnostic Kit for the Evaluation of Air Compressor Operation is Introduced {1803}
2004/11/15
Specifications
V-Belt Tension Chart
3208 VEHICULAR ENGINE
Disassembly and Assembly
Belt Tightener
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Belt Tightener (Water Pump)
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
Stronger Idler Pulley Assembly Used With Fan Belts{1358}
1978/05/22
New Idler Pulley Assembly Used In Air Compressor Group {1803}
1990/02/05
Information that Improves the Service Life of the Remanufactured Air Conditioning Compressor {1357, 1358, 1397, 1802, 1805, 1809, 7320, 7342, 7343}
2008/03/10
Exhaust Brakes Can Not Be Installed On All Remanufactured 3208 Engine Arrangements {1119}
1993/12/20
Special Instruction
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Specifications
Camshaft
3208 VEHICULAR ENGINE
Reuse And Salvage Guidelines
Reuse and Salvage for Camshafts {1210, 1210}
Reuse and Salvage for Camshafts {1210, 1210}
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Disassembly and Assembly
Camshaft
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Camshaft Bearings
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
Lubricant Gives Protection To Camshaft And Roller During Initial Start-Up{1210,1209}
1981/09/21
Identification Of Camshaft Groups And Valve Mechanism Groups{1210,1102}
1984/11/26
Maximum Wear Limits Established For Camshaft Roller Followers{1209}
1985/09/30
New 8T2998 Lubricant Available{0645,1210}
1986/02/17
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures{1209}
1977/05/16
Remanufactured Camshafts And Cam Kits Available For Parts Service{1210,1211,1212}
1990/12/17
Improved Cylinder Head Gasket{1101,1201}
1984/05/21
Do Not Use Plastic Tubing With Brass Couplings As A Fuel Supply Line{1274}
1977/10/03
Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03
Special Instruction
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installing Crankshaft Bearing Caps On 4.5" Bore V8 Direct Injection Engines{1200}
Installing Crankshaft Bearing Caps On 4.5" Bore V8 Direct Injection Engines{1200}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Special Handling Information And Installation Instructions For Crankshaft Seal Groups That Have Hydrodynamic Grooves In The Sealing Lip{1160, 1161}
Special Handling Information And Installation Instructions For Crankshaft Seal Groups That Have Hydrodynamic Grooves In The Sealing Lip{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Specifications
Crankshaft
3208 VEHICULAR ENGINE
Tool Operating Manual
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
Reuse And Salvage Guidelines
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Reuse and Salvage for Crankshafts {0674, 1202}
Reuse and Salvage for Crankshafts {0674, 1202}
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
Reuse and Salvage for Engine Dampers {1202, 1205}
Reuse and Salvage for Engine Dampers {1202, 1205}
Disassembly and Assembly
Crankshaft Main Bearings
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Crankshaft Pulley
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Crankshaft Front Seal
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Crankshaft Rear Seal And Wear Sleeve
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Crankshaft And Gear
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
1980 Caterpillar Remanufactured Products Catalog Is Now Available{0374}
1980/06/23
Comparison And Applications Of Six And Eight Counterweight Crankshafts{1202,1156}
1981/08/17
New Crankshaft Seal Group Has Assembled Rear Seal And Wear Sleeve{1161}
1982/01/25
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
List Of Main And Connecting Rod Bearings Currently Available{1203,1219,1230,1226,1227}
1982/06/07
Engine Ground Straps Necessary To Prevent Electrical Discharge Damage To Crankshaft Bearings{1202,1203,1400,1405}
1982/06/21
Wider Crankshaft Gear Used{1202,1204,1206}
1982/10/11
New Crankshaft Seal Group Has Assembled Rear Seal And Wear Sleeve{1161}
1982/10/18
6V6142 And 6V6143 Installers Can Be Used To Install Crankshaft Seals And Wear Sleeves{0622,0626,1160,1161}
1982/11/01
Check Cylinder Bores For Chamfer During Reconditioning{1202,1222,1223}
1983/02/14
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Reuse Of Engine Bearings{1230}
1983/05/16
Crankshaft Failures{1202,1230}
1983/11/21
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Remanufactured Undersize Crankshafts Are Available{1202}
1983/11/21
New Main And Connecting Rod Bearings Have Copper Bond Material{1203,1219,1230}
1984/10/01
Rebuilt Standard Size Crankshafts Used In Some Remanufactured Engines{1202}
1984/12/10
New Rear Crankshaft Seal Has Longer Service Life{1161}
1985/01/21
Installing New Copper Bonded Bearings Can Extend Engine Life{1230,1203,1219}
1985/04/29
Remanufactured Crankshafts Are Available In Standard And Two Undersize Dimensions (U.S. and Canada){1202,7754}
1985/11/18
Put Grease On Front Crankshaft Seal Before Installing The Crankshaft Pulley And Damper{1160}
1986/01/13
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
Caterpillar Crankshaft Heat Code Locations{1202}
1986/10/20
Lightening Holes Not Drilled In Some Crankshafts{1202}
1977/01/24
Tools To Install Crankshaft Seal And Wear Sleeve{1160,1161,0622}
1977/07/11
Check For Extra Holes In Crankshaft Flange If Oil Leaks From Between The Flywheel And Crankshaft Flange{1156,1202}
1977/09/05
Improved Main, Thrust And Connecting Rod Bearings Have Aluminum Alloy With More Strength{1230}
1977/10/17
Crankshaft Support Groups Are Available To Measure Bent Crankshafts{0653,1202}
1977/11/07
Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12
Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28
New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04
Engines Can Use Crankshafts With Either Six Or Eight Counterweights {1202}
1979/09/10
New Pistons Used With Two Keystone Compression Rings{1156,1205,1214,1215}
1989/06/19
New Connecting Rod and Main Bearing Kits Available{1230,1203,1219}
1989/10/30
Checking Crankshaft Journal Surface Hardness On Remanufactured Crankshafts{1202}
1991/01/07
Use the 171-7212 Wear Sleeve to Repair the Crankshaft Hub {1160}
2011/09/20
40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16
Special Instruction
Installation Of 4W6143 Sleeve{1201}
Installation Of 4W6143 Sleeve{1201}
Installation of 3208T Remanufactured Engine for Industrial, Truck and Electrical Power Generation (EPG) Engines{1200}
Installation of 3208T Remanufactured Engine for Industrial, Truck and Electrical Power Generation (EPG) Engines{1200}
Installation of Dipstick Guide - 0R0724 and 0R0725 Remanufactured Short Blocks for 3204 Engines{1201, 1300, 7450}
Installation of Dipstick Guide - 0R0724 and 0R0725 Remanufactured Short Blocks for 3204 Engines{1201, 1300, 7450}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installing Crankshaft Bearing Caps On 4.5" Bore V8 Direct Injection Engines{1200}
Installing Crankshaft Bearing Caps On 4.5" Bore V8 Direct Injection Engines{1200}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
installation of 9n6275 cylinder sleeve{1222}
installation of 9n6275 cylinder sleeve{1222}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Cylinder Block Cleaning Procedure{1201}
Cylinder Block Cleaning Procedure{1201}
Installation Of Short Block Group And Cylinder Block Service Group For 1100, 3100 And 3208 Naturally Aspirated Engines Or 3208 Turbocharged Engines{1200, 1201}
Installation Of Short Block Group And Cylinder Block Service Group For 1100, 3100 And 3208 Naturally Aspirated Engines Or 3208 Turbocharged Engines{1200, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Specifications
Cylinder Block
3208 VEHICULAR ENGINE
Bearings For Connecting Rods And Mains
3208 VEHICULAR ENGINE
Tool Operating Manual
Setup and Operation of the 368-8645 Tool Kit (CRANKCASE PRESSURE){1317}
Setup and Operation of the 368-8645 Tool Kit (CRANKCASE PRESSURE){1317}
Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}
Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
Reuse And Salvage Guidelines
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for 3200 Engine Cylinder Blocks {1201}
Reuse and Salvage for 3200 Engine Cylinder Blocks {1201}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}
Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Cylinder Block Salvage Procedure Using Belzona&reg; 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Disassembly and Assembly
Crankshaft Main Bearings
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Flywheel Housing
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Camshaft Bearings
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
New Cylinder Sleeve Is Available For Repairs Of Worn And/Or Damaged Cylinders{1216,1201}
1980/06/02
1980 Caterpillar Remanufactured Products Catalog Is Now Available{0374}
1980/06/23
Resurfaced Cylinder Blocks And Heads{1201,1101,1000}
1982/03/08
Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
List Of Main And Connecting Rod Bearings Currently Available{1203,1219,1230,1226,1227}
1982/06/07
Engine Ground Straps Necessary To Prevent Electrical Discharge Damage To Crankshaft Bearings{1202,1203,1400,1405}
1982/06/21
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Wider Crankshaft Gear Used{1202,1204,1206}
1982/10/11
Resurfaced Cylinder BlocksAnd Heads{1201,1101,1000}
1982/10/25
Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29
New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29
Improved Cylinder Head Gasket{1101,1201}
1983/01/24
Check Cylinder Bores For Chamfer During Reconditioning{1202,1222,1223}
1983/02/14
New Reconditioning Specifications For Cylinders Decrease Piston Scuffing And Seizure {0374,1223,1216,1201}
1983/04/18
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Reuse Of Engine Bearings{1230}
1983/05/16
New Procedure And New Tool Can Be Used To Remove Cylinder Sleeves From The Cylinder Block{1222,1223}
1983/08/08
Broken Edge Filter Or Plugged Cylinder Head Adapter Can Cause Rough Engine Operation Or Low Power{1252}
1983/10/17
Sleeve Can Be Used For Reconditioning The Mounting Bore For The Fuel Pump Housing In The Cylinder Block{1201}
1983/11/21
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Improved Cylinder Head Gasket{1101,1201}
1984/05/21
New Relief Valve Guide Used In Oil Pump{1315}
1984/07/16
New Main And Connecting Rod Bearings Have Copper Bond Material{1203,1219,1230}
1984/10/01
Check Cylinder Block And Head Flatness Whenever There Is A Head Gasket Failure{1100,1200}
1985/04/01
Improved Cylinder Head Gasket{1101,1201}
1986/03/24
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Flywheel Housing With 6&deg; Offset Transmission Mounting Holes Must Be Used In GMC Trucks{1000,1157}
1986/06/09
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20
Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12
New Information On Reusable Cylinder Liners{1216}
1978/06/19
Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28
New Engine Cylinder Block Used{1201}
1979/03/05
New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Recommendation For Use Of A FLEX-HONE On 1100, 3100 and 3200 Series Engines {1201}
1979/09/10
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
New Connecting Rod and Main Bearing Kits Available{1230,1203,1219}
1989/10/30
Parts Service Information For Pistons{1214,1225,1331}
1990/05/14
Remanufactured Camshafts And Cam Kits Available For Parts Service{1210,1211,1212}
1990/12/17
Checking Crankshaft Journal Surface Hardness On Remanufactured Crankshafts{1202}
1991/01/07
Compression Ratio Increased On Remanufactured OR1094 &amp; OR1095 Engines To Reduce Amount Of White Smoke On Cold Weather Start-Ups{1000,1254,1290}
1991/09/30
Special Instruction
Installation of Head Gasket (With New Torque Procedure){1100}
Installation of Head Gasket (With New Torque Procedure){1100}
Adaptability of 7C1599 Cylinder Head Gasket{1100}
Adaptability of 7C1599 Cylinder Head Gasket{1100}
Installation Of Remanufactured Cylinder Head Groups{1101}
Installation Of Remanufactured Cylinder Head Groups{1101}
Using The 6V-7770 Valve Guide Kit And 6V-7755 Spring Seat Guide{670, 1104}
Using The 6V-7770 Valve Guide Kit And 6V-7755 Spring Seat Guide{670, 1104}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V7028 Spring Seat Enlarger For 3200 Cylinder Heads{1101}
Use Of 6V7028 Spring Seat Enlarger For 3200 Cylinder Heads{1101}
Installation Of 1W4259 Valve Spring{1108}
Installation Of 1W4259 Valve Spring{1108}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Installation Of Replacement Cylinder Head Groups (Non-Turbocharged){1101}
Installation Of Replacement Cylinder Head Groups (Non-Turbocharged){1101}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Installation Of Replacement Cylinder Head Assemblies{1101}
Installation Of Replacement Cylinder Head Assemblies{1101}
Installation Of Replacement Cylinder Head Groups (Turbocharged){1101}
Installation Of Replacement Cylinder Head Groups (Turbocharged){1101}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Service Letter-NACD
Remanufactured Cylinder Heads Need To Be Removed From Parts Stock And Returned For Rework
Remanufactured Cylinder Heads Need To Be Removed From Parts Stock And Returned For Rework
Service Letter-Australia
Service Letter-CFEL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Valve Covers
3208 VEHICULAR ENGINE
Valves<BR> (Engines with Serial Numbers 79V1-79V1407)
3208 VEHICULAR ENGINE
Valve Seats And Inserts<BR> (Engines with Serial Numbers 79V1-79V1407)
3208 VEHICULAR ENGINE
Valves<BR> (Engines with Serial Numbers 79V1408-Up)
3208 VEHICULAR ENGINE
Valve Seats And Inserts<BR> (Engines with Serial Numbers 79V1408-Up)
3208 VEHICULAR ENGINE
Cylinder Head
3208 VEHICULAR ENGINE
Tool Operating Manual
Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767}
Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767}
Operating Instructions for 148-2997 Valve Recession Tool Group Used On 3600, G3600, and C175 Engines{0374, 0599, 0701, 0703, 0759}
Operating Instructions for 148-2997 Valve Recession Tool Group Used On 3600, G3600, and C175 Engines{0374, 0599, 0701, 0703, 0759}
188-3922 Broken Exhaust Bolt and Stud Removal Group for 3114, 3116, 3126, 3126B, 3176, 3176B, C-10, and C12 Engines{0374, 0599, 0701, 0702, 0703}
188-3922 Broken Exhaust Bolt and Stud Removal Group for 3114, 3116, 3126, 3126B, 3176, 3176B, C-10, and C12 Engines{0374, 0599, 0701, 0702, 0703}
CRB Valve Spring Testers 8S-2263 and 4C-9496{0374, 0599, 0700, 0701, 1108}
CRB Valve Spring Testers 8S-2263 and 4C-9496{0374, 0599, 0700, 0701, 1108}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
Service Letter-China
Remanufactured Cylinder Heads Need To Be Removed From Parts Stock And Returned For Rework
Remanufactured Cylinder Heads Need To Be Removed From Parts Stock And Returned For Rework
Service Letter-Asia
Reuse And Salvage Guidelines
Engine Valve Failure Modes{1100, 1105}
Engine Valve Failure Modes{1100, 1105}
Reuse and Salvage for Cylinder Head Assemblies {1100, 1101, 1103, 1104, 1105, 1106, 1108, 1109, 1115, 1117, 1121, 1124, 1125}
Reuse and Salvage for Cylinder Head Assemblies {1100, 1101, 1103, 1104, 1105, 1106, 1108, 1109, 1115, 1117, 1121, 1124, 1125}
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Applied Failure Analysis
Engine Valve Failure Modes{1100, 1105}
Engine Valve Failure Modes{1100, 1105}
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Service Letter-APD
Remanufactured Cylinder Heads Need To Be Removed From Parts Stock And Returned For Rework
Remanufactured Cylinder Heads Need To Be Removed From Parts Stock And Returned For Rework
Disassembly and Assembly
Cylinder Heads
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
Larger Valve Springs{1108,1101,1252}
1981/05/04
New Spacers Used With Larger Valve Springs{1108,1101}
1981/08/10
Higher Torque Used With Later Head Bolts {1000,1101}
1981/09/14
Resurfaced Cylinder Blocks And Heads{1201,1101,1000}
1982/03/08
Improved Relief Valve Guide Decreases Maximum Oil Pressure During Cold Weather Starts{1315,1304}
1982/04/26
Vacuum Tester Checks For Leaks Between Valve Face and Seat{0651,1103,1105}
1982/09/06
Resurfaced Cylinder BlocksAnd Heads{1201,1101,1000}
1982/10/25
New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29
Improved Cylinder Head Gasket{1101,1201}
1983/01/24
Engine Valve Stem &quot;Use Again&quot; Specifications{0653,1105}
1983/02/28
Improved Valve Springs Available{1108}
1983/04/04
Broken Edge Filter Or Plugged Cylinder Head Adapter Can Cause Rough Engine Operation Or Low Power{1252}
1983/10/17
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1983/10/17
Correct Installation Of New Valve Springs{1108}
1983/11/21
Replacement Valve Guides Can Be Used To Recondition Cylinder Heads{1104}
1983/12/19
Remanufactured Cylinder Head Assemblies{1100,1101}
1984/02/13
Improved Cylinder Head Gasket{1101,1201}
1984/05/21
Remanufactured Cylinder Head Groups{1100,1101,7554}
1984/11/19
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Check Cylinder Block And Head Flatness Whenever There Is A Head Gasket Failure{1100,1200}
1985/04/01
Head Gasket Replacement Procedure{0350,1100}
1985/08/05
Improved Cylinder Head Gasket{1101,1201}
1986/03/24
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Valve Lash Adjustment Interval Is Changed {1105}
1986/07/07
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures{1209}
1977/05/16
Tools Now Available To Ream And/Or Hone 0.500&quot; (12.70 mm) Diameter Valve Guides{0663}
1977/08/22
Intake Valve Seals Used{1105,1300}
1987/11/23
Tolerance Added To Valve Clearance Specifications{1105,0374}
1978/01/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1978/01/30
Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/06
Engine Valve Springs Are Now Made Of Carbon Steel Alloy{1101,1108}
1979/02/19
A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
New Head Gasket Used {1124}
1989/05/15
New Pistons Used With Two Keystone Compression Rings{1156,1205,1214,1215}
1989/06/19
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads{1105,1101}
1990/10/08
Compression Ratio Increased On Remanufactured OR1094 &amp; OR1095 Engines To Reduce Amount Of White Smoke On Cold Weather Start-Ups{1000,1254,1290}
1991/09/30
Clarify Usage Of Parts Service Cylinder Head Gaskets{1124}
1994/01/10
Caterpillar Warranty Claims on Cylinder Head Valves {1105}
2005/10/03
Specifications
Pulley And Damper
3208 VEHICULAR ENGINE
Reuse And Salvage Guidelines
Reuse and Salvage for Cast Iron & Steel Pulleys and Stub Shafts {1205, 1207, 1384, 1425}
Reuse and Salvage for Cast Iron & Steel Pulleys and Stub Shafts {1205, 1207, 1384, 1425}
Reuse and Salvage for Engine Dampers {1202, 1205}
Reuse and Salvage for Engine Dampers {1202, 1205}
Disassembly and Assembly
Crankshaft Pulley
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
Put Grease On Front Crankshaft Seal Before Installing The Crankshaft Pulley And Damper{1160}
1986/01/13
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
8T5314 Socket Adapter Available To Correctly Install Alternator Pulley Nut {0601}
1988/01/25
New Pistons Used With Two Keystone Compression Rings{1156,1205,1214,1215}
1989/06/19
Dampers Prevent Failure Of Retaining (Stack) Bolts In Transmission Clutch Housings {3155,3169}
1989/08/07
Disassembly and Assembly
Fan And Fan Drive
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
New Fan Drive Group Has Tapered Roller Bearings{1359}
1984/05/21
New Design Fan Group Gives Longer Service Life{1356,1359}
1978/12/11
Special Instruction
Water Pump Reconditioning Using The 9N3139 Rebuild Kit And 5P7361 Tool Group{1361}
Water Pump Reconditioning Using The 9N3139 Rebuild Kit And 5P7361 Tool Group{1361}
Installation Of 2W0172 Water Pump Seal Assembly With 5P9722 Driver{1361}
Installation Of 2W0172 Water Pump Seal Assembly With 5P9722 Driver{1361}
Technical Information Bulletin
Remanufactured Water Pumps For 3204 And 3208 Engines
Remanufactured Water Pumps For 3204 And 3208 Engines
Specifications
Pump Drive For Supplemental Steering<BR> (Part of Differential and Bevel Gear Group)
613B WHEEL TRACTOR-SCRAPER STEERING SYSTEM
Disassembly and Assembly
Governor And Fuel Injection Pump Drive
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
1980 Caterpillar Remanufactured Products Catalog Is Now Available{0374}
1980/06/23
Troubleshooting: Water Pump Failures {1361,1350}
1981/09/14
Holes Added To Water Pump Impeller{1361}
1982/05/17
New Water Pumps Use New Seal And Impeller {1361}
1982/09/13
Use FT1783 Fixture To Drill Vent Holes In Impeller{0665,1361}
1983/02/28
Use Vacuum Tester For Quality Control Check Of Water Pump Seal{0652,1361}
1983/02/28
Special Tools For Complete Repair Of Water Pump In Direct Injection Engines{0620,1361}
1977/05/02
Improved Water Pump Group Now Used{1361}
1978/01/09
A Washer With Closer Tolerances Is Now Used In The Governor And Fuel Pump Drive Group{1288,7462}
1978/11/20
New Water Pump Assemblies Use An Improved Seal Assembly{1361}
1979/06/25
Special Instruction
Water Pump Reconditioning Using The 9N3139 Rebuild Kit And 5P7361 Tool Group{1361}
Water Pump Reconditioning Using The 9N3139 Rebuild Kit And 5P7361 Tool Group{1361}
Installation Of 2W0172 Water Pump Seal Assembly With 5P9722 Driver{1361}
Installation Of 2W0172 Water Pump Seal Assembly With 5P9722 Driver{1361}
Technical Information Bulletin
Remanufactured Water Pumps For 3204 And 3208 Engines
Remanufactured Water Pumps For 3204 And 3208 Engines
Service Magazine
1980 Caterpillar Remanufactured Products Catalog Is Now Available{0374}
1980/06/23
Troubleshooting: Water Pump Failures {1361,1350}
1981/09/14
Holes Added To Water Pump Impeller{1361}
1982/05/17
New Water Pump Uses New Seal And Impeller{1361}
1982/09/06
New Water Pumps Use New Seal And Impeller {1361}
1982/09/13
Use FT1783 Fixture To Drill Vent Holes In Impeller{0665,1361}
1983/02/28
Use Vacuum Tester For Quality Control Check Of Water Pump Seal{0652,1361}
1983/02/28
Special Tools For Complete Repair Of Water Pump In Direct Injection Engines{0620,1361}
1977/05/02
Improved Water Pump Group Now Used{1361}
1978/01/09
New Water Pump Assemblies Use An Improved Seal Assembly{1361}
1979/06/25
Special Instruction
Troubleshooting Engine Vibration In Vehicular Equipment{1000}
Troubleshooting Engine Vibration In Vehicular Equipment{1000}
Instructions For 3208 Engine Tune-Up{1000}
Instructions For 3208 Engine Tune-Up{1000}
Instructions For 3208 Engine Oil Filter Base Installation{1306}
Instructions For 3208 Engine Oil Filter Base Installation{1306}
Installation of 3208 Remanufactured Engine (Natural Aspiration) for Industrial, Vehicular or Lift Truck Applications{1000}
Installation of 3208 Remanufactured Engine (Natural Aspiration) for Industrial, Vehicular or Lift Truck Applications{1000}
Installation of 3208T Remanufactured Engine for Industrial, Truck and Electrical Power Generation (EPG) Engines{1200}
Installation of 3208T Remanufactured Engine for Industrial, Truck and Electrical Power Generation (EPG) Engines{1200}
Installation of Dipstick Guide - 0R0724 and 0R0725 Remanufactured Short Blocks for 3204 Engines{1201, 1300, 7450}
Installation of Dipstick Guide - 0R0724 and 0R0725 Remanufactured Short Blocks for 3204 Engines{1201, 1300, 7450}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Installation Of Short Block Group And Cylinder Block Service Group For 1100, 3100 And 3208 Naturally Aspirated Engines Or 3208 Turbocharged Engines{1200, 1201}
Installation Of Short Block Group And Cylinder Block Service Group For 1100, 3100 And 3208 Naturally Aspirated Engines Or 3208 Turbocharged Engines{1200, 1201}
Oil and Your Engine {1000}
Oil and Your Engine {1000}
Service Magazine
Real Value Available Through Caterpillar Remanufacturing Programs{0374}
1980/02/04
1980 Caterpillar Remanufactured Products Catalog Is Now Available{0374}
1980/06/23
Higher Torque Used With Later Head Bolts {1000,1101}
1981/09/14
Reference Chart For Major Production Changes On 3208 Engines{0374,0375,1000}
1981/10/19
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Resurfaced Cylinder Blocks And Heads{1201,1101,1000}
1982/03/08
Separate Valve Stem Gauges Available{0653,1000}
1982/06/07
Analyzing A Major Engine Failure{1000}
1982/07/19
Reference Chart for Engine Improvements{0374,1000}
1982/10/25
Additions To Reference Chart For Major Production Changes {0374,0375,1000}
1985/01/14
New Index Lists Engine Special Instructions By SMCS Code{1000,0374}
1986/04/07
Flywheel Housing With 6&deg; Offset Transmission Mounting Holes Must Be Used In GMC Trucks{1000,1157}
1986/06/09
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Testing The Starter On The Engine{1401,1450}
1987/05/04
The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
Microfiche For Replacement Engine Bills Of Material {0374,1000}
1987/10/26
Explanation Of Nomenclature Used In Engine Performance{1000,0374}
1978/05/15
Lubrication For A Rebuilt Engine{0374,1000}
1978/06/19
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24
Check The Radiator Fan Spider Assembly When Doing Yearly General Maintenance{1356}
1989/07/24
Engine Coolant Can Be Recycled{1395}
1989/11/13
Compression Ratio Increased On Remanufactured OR1094 &amp; OR1095 Engines To Reduce Amount Of White Smoke On Cold Weather Start-Ups{1000,1254,1290}
1991/09/30
Engine Storage and Engine Start-Up After Storage {1000, 1300, 1348, 7418}
Engine Storage and Engine Start-Up After Storage {1000, 1300, 1348, 7418}
Reuse And Salvage Guidelines
Inspection and Reuse of Critical Fasteners Used in All Engines {7553, 7553}
Inspection and Reuse of Critical Fasteners Used in All Engines {7553, 7553}
Specifications
Flywheel
3208 VEHICULAR ENGINE
Flywheel Runout
3208 VEHICULAR ENGINE
Flywheel Housing Runout
3208 VEHICULAR ENGINE
Flywheel Housing Bore
3208 VEHICULAR ENGINE
Reuse And Salvage Guidelines
Reuse and Salvage for Flywheel Assemblies {1156}
Reuse and Salvage for Flywheel Assemblies {1156}
Disassembly and Assembly
Flywheel
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Flywheel Housing
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
Comparison And Applications Of Six And Eight Counterweight Crankshafts{1202,1156}
1981/08/17
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Wider Crankshaft Gear Used{1202,1204,1206}
1982/10/11
Flywheel Housing With 6&deg; Offset Transmission Mounting Holes Must Be Used In GMC Trucks{1000,1157}
1986/06/09
Check For Extra Holes In Crankshaft Flange If Oil Leaks From Between The Flywheel And Crankshaft Flange{1156,1202}
1977/09/05
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Engine News
An Improved Front Gear Train Timing Procedure Is Used for 3406E, 3456, C-15, C-16, C15, and C18 Engines {1206}
2012/12/14
Reuse And Salvage Guidelines
Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}
Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}
Disassembly and Assembly
Crankshaft Front Seal
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Timing Gear Cover And Oil Pump
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Crankshaft And Gear
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
6V3100 Diesel Timing Indicator Group Available To Check Engine/Fuel System Timing And Mechanical Advance During Operation{0653,1206,1156}
1981/08/31
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Wider Crankshaft Gear Used{1202,1204,1206}
1982/10/11
Tachometer Drive Is Now An Attachment{1166,1250,7450,7452,7487}
1985/08/12
Put Grease On Front Crankshaft Seal Before Installing The Crankshaft Pulley And Damper{1160}
1986/01/13
An Improved Front Gear Train Timing Procedure Is Used for 3406E, 3456, C-15, C-16, C15, and C18 Engines {1206}
2012/12/13
Specifications
Flywheel Housing Runout
3208 VEHICULAR ENGINE
Flywheel Housing Bore
3208 VEHICULAR ENGINE
Disassembly and Assembly
Crankshaft Rear Seal And Wear Sleeve
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Flywheel Housing
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
New Crankshaft Seal Group Has Assembled Rear Seal And Wear Sleeve{1161}
1982/01/25
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine{0651,0654,1250}
1982/03/22
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
New Crankshaft Seal Group Has Assembled Rear Seal And Wear Sleeve{1161}
1982/10/18
New Rear Crankshaft Seal Has Longer Service Life{1161}
1985/01/21
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
Flywheel Housing With 6&deg; Offset Transmission Mounting Holes Must Be Used In GMC Trucks{1000,1157}
1986/06/09
Use The 6V2034 Micrometer Adapter To Measure Lip Thickness Of Engine Valves {0653,1105}
1979/10/29
Disassembly and Assembly
Crankshaft Front Seal
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Timing Gear Cover And Oil Pump
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
6V3100 Diesel Timing Indicator Group Available To Check Engine/Fuel System Timing And Mechanical Advance During Operation{0653,1206,1156}
1981/08/31
Wider Crankshaft Gear Used{1202,1204,1206}
1982/10/11
Tachometer Drive Is Now An Attachment{1166,1250,7450,7452,7487}
1985/08/12
Put Grease On Front Crankshaft Seal Before Installing The Crankshaft Pulley And Damper{1160}
1986/01/13
Special Instruction
Installation Of 4W6143 Sleeve{1201}
Installation Of 4W6143 Sleeve{1201}
Installation of Dipstick Guide - 0R0724 and 0R0725 Remanufactured Short Blocks for 3204 Engines{1201, 1300, 7450}
Installation of Dipstick Guide - 0R0724 and 0R0725 Remanufactured Short Blocks for 3204 Engines{1201, 1300, 7450}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Cylinder Block Cleaning Procedure{1201}
Cylinder Block Cleaning Procedure{1201}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Installation Of Short Block Group And Cylinder Block Service Group For 1100, 3100 And 3208 Naturally Aspirated Engines Or 3208 Turbocharged Engines{1200, 1201}
Installation Of Short Block Group And Cylinder Block Service Group For 1100, 3100 And 3208 Naturally Aspirated Engines Or 3208 Turbocharged Engines{1200, 1201}
Service Magazine
Real Value Available Through Caterpillar Remanufacturing Programs{0374}
1980/02/04
Crankcase Capacity Increased And New Oil Level Gauges Used; Specifications For Conversion Of Existing Gauges{1318,1302}
1980/04/21
New Cylinder Sleeve Is Available For Repairs Of Worn And/Or Damaged Cylinders{1216,1201}
1980/06/02
High Concentration Of Aluminum In Oil Analysis Can Be The Result Of Rocker Arm Support Wear{1318,1102}
1981/03/02
Check Oil Level Carefully To Prevent Operation With Too Much Oil In Engine Crankcase{1316}
1981/03/02
Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08
Comparison And Applications Of Six And Eight Counterweight Crankshafts{1202,1156}
1981/08/17
6V3100 Diesel Timing Indicator Group Available To Check Engine/Fuel System Timing And Mechanical Advance During Operation{0653,1206,1156}
1981/08/31
Lubricant Gives Protection To Camshaft And Roller During Initial Start-Up{1210,1209}
1981/09/21
Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22
New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine{0651,0654,1250}
1982/03/22
Holes Added To Water Pump Impeller{1361}
1982/05/17
Separate Valve Stem Gauges Available{0653,1000}
1982/06/07
List Of Main And Connecting Rod Bearings Currently Available{1203,1219,1230,1226,1227}
1982/06/07
Engine Ground Straps Necessary To Prevent Electrical Discharge Damage To Crankshaft Bearings{1202,1203,1400,1405}
1982/06/21
Use Correct Torque To Prevent Broken Rocker Arm Shafts{1102}
1982/07/05
New Water Pump Uses New Seal And Impeller{1361}
1982/09/06
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Wider Crankshaft Gear Used{1202,1204,1206}
1982/10/11
New Crankshaft Seal Group Has Assembled Rear Seal And Wear Sleeve{1161}
1982/10/18
Resurfaced Cylinder BlocksAnd Heads{1201,1101,1000}
1982/10/25
Reference Chart for Engine Improvements{0374,1000}
1982/10/25
6V6142 And 6V6143 Installers Can Be Used To Install Crankshaft Seals And Wear Sleeves{0622,0626,1160,1161}
1982/11/01
Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08
Use the 6V6167 Contact Point to Measure Wear Steps on Piston Pins{0653}
1982/11/22
New Piston Design Decreases Oil Consumption{1214,1215}
1982/12/20
Improved Cylinder Head Gasket{1101,1201}
1983/01/24
Check Cylinder Bores For Chamfer During Reconditioning{1202,1222,1223}
1983/02/14
Use FT1783 Fixture To Drill Vent Holes In Impeller{0665,1361}
1983/02/28
Engine Valve Stem &quot;Use Again&quot; Specifications{0653,1105}
1983/02/28
Use Vacuum Tester For Quality Control Check Of Water Pump Seal{0652,1361}
1983/02/28
New Shutoff Solenoid Group Used{1259}
1983/03/21
New Reconditioning Specifications For Cylinders Decrease Piston Scuffing And Seizure {0374,1223,1216,1201}
1983/04/18
Installation Of Bearing For Connecting Rod Piston Pin{1219}
1983/05/09
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Reuse Of Engine Bearings{1230}
1983/05/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1983/10/17
Sleeve Can Be Used For Reconditioning The Mounting Bore For The Fuel Pump Housing In The Cylinder Block{1201}
1983/11/21
Crankshaft Failures{1202,1230}
1983/11/21
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Remanufactured Undersize Crankshafts Are Available{1202}
1983/11/21
Correct Installation Of New Valve Springs{1108}
1983/11/21
Replacement Valve Guides Can Be Used To Recondition Cylinder Heads{1104}
1983/12/19
Remanufactured Cylinder Head Assemblies{1100,1101}
1984/02/13
New Relief Valve Guide Used In Oil Pump{1315}
1984/07/16
New Main And Connecting Rod Bearings Have Copper Bond Material{1203,1219,1230}
1984/10/01
Identification Of Camshaft Groups And Valve Mechanism Groups{1210,1102}
1984/11/26
New Rear Crankshaft Seal Has Longer Service Life{1161}
1985/01/21
Check Cylinder Block And Head Flatness Whenever There Is A Head Gasket Failure{1100,1200}
1985/04/01
Installing New Copper Bonded Bearings Can Extend Engine Life{1230,1203,1219}
1985/04/29
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
Tachometer Drive Is Now An Attachment{1166,1250,7450,7452,7487}
1985/08/12
Maximum Wear Limits Established For Camshaft Roller Followers{1209}
1985/09/30
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Remanufactured Crankshafts Are Available In Standard And Two Undersize Dimensions (U.S. and Canada){1202,7754}
1985/11/18
Put Grease On Front Crankshaft Seal Before Installing The Crankshaft Pulley And Damper{1160}
1986/01/13
New 8T2998 Lubricant Available{0645,1210}
1986/02/17
Improved Cylinder Head Gasket{1101,1201}
1986/03/24
New Index Lists Engine Special Instructions By SMCS Code{1000,0374}
1986/04/07
Increase Piston Reuse With Keystone Piston Ring Gauge Group{1214,1215}
1986/06/16
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
Check Connecting Rods After Engine Failures Involving Hydraulic Lock{1218,1225}
1986/10/20
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Lightening Holes Not Drilled In Some Crankshafts{1202}
1977/01/24
Improved Shut-Off Solenoids For Engines Equipped With Sleeve Metering Fuel Systems{1259}
1977/03/07
New Engine Mount Keeps Forces Caused From Engine Side-To-Side Movement Away From The Frame Of The Vehicle{1152}
1977/03/21
Special Tools For Complete Repair Of Water Pump In Direct Injection Engines{0620,1361}
1977/05/02
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
Tools Now Available To Ream And/Or Hone 0.500&quot; (12.70 mm) Diameter Valve Guides{0663}
1977/08/22
Check For Extra Holes In Crankshaft Flange If Oil Leaks From Between The Flywheel And Crankshaft Flange{1156,1202}
1977/09/05
Improved Main, Thrust And Connecting Rod Bearings Have Aluminum Alloy With More Strength{1230}
1977/10/17
Crankshaft Support Groups Are Available To Measure Bent Crankshafts{0653,1202}
1977/11/07
Excessive Oil Consumption Can Be Caused By Dirt In Air Inlet System Or By Flaking Of The Piston Compression Ring{1213,1215}
1977/12/12
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20
Microfiche For Replacement Engine Bills Of Material {0374,1000}
1987/10/26
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
Improved Water Pump Group Now Used{1361}
1978/01/09
Tolerance Added To Valve Clearance Specifications{1105,0374}
1978/01/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1978/01/30
Air Line For Air Compressor Governor Now Connected To Outlet For Wet Air Tank{4272,1065,4278}
1978/01/30
Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/06
Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24
Explanation Of Nomenclature Used In Engine Performance{1000,0374}
1978/05/15
Stronger Idler Pulley Assembly Used With Fan Belts{1358}
1978/05/22
Procedures And Cautions For Use Of A Flex-Hone On 3204 And 3208 Engines{1201}
1978/06/05
Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28
A Washer With Closer Tolerances Is Now Used In The Governor And Fuel Pump Drive Group{1288,7462}
1978/11/20
New 6V87 Gauge Measures Valve Stem Wear{0653,1105}
1979/01/08
Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22
Engine Valve Springs Are Now Made Of Carbon Steel Alloy{1101,1108}
1979/02/19
New Engine Cylinder Block Used{1201}
1979/03/05
New Piston And Connecting Rod Are Tapered In Area Of Piston Pin{1213,1214,1218,1219}
1979/03/05
5P3519 Piston Ring Gauge Has Improved Design For Better Accuracy And Easier Use; Corrected Information For Use On Pistons That Have Two Ring Grooves{0653,1214}
1979/05/14
A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28
New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03
Recommendation For Use Of A FLEX-HONE On 1100, 3100 and 3200 Series Engines {1201}
1979/09/10
Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
New Pistons Used With Two Keystone Compression Rings{1156,1205,1214,1215}
1989/06/19
Check The Radiator Fan Spider Assembly When Doing Yearly General Maintenance{1356}
1989/07/24
New Connecting Rod and Main Bearing Kits Available{1230,1203,1219}
1989/10/30
Engine Coolant Can Be Recycled{1395}
1989/11/13
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads{1105,1101}
1990/10/08
Installation Of Zinc Rods In Caterpillar Marine Engines{1350,1388}
1990/12/24
Checking Crankshaft Journal Surface Hardness On Remanufactured Crankshafts{1202}
1991/01/07
Exhaust Brakes Can Not Be Installed On All Remanufactured 3208 Engine Arrangements {1119}
1993/12/20
Identification Of External Terminals On Alternators {1405,1406,1400}
1998/12/07
Specifications
Front Support For Engine<BR> (225 Excavator)
3208 VEHICULAR ENGINE
Disassembly and Assembly
Engine Front Support
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Engine Rear Supports
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
6V3100 Diesel Timing Indicator Group Available To Check Engine/Fuel System Timing And Mechanical Advance During Operation{0653,1206,1156}
1981/08/31
Flywheel Housing With 6&deg; Offset Transmission Mounting Holes Must Be Used In GMC Trucks{1000,1157}
1986/06/09
New Engine Mount Keeps Forces Caused From Engine Side-To-Side Movement Away From The Frame Of The Vehicle{1152}
1977/03/21
0R5207 Remanufactured Starter May Not Fit In Some Applications{1453}
1993/11/29
Specifications
Manifolds And Crankcase Ventilation Valve
3208 VEHICULAR ENGINE
Oil Pan
3208 VEHICULAR ENGINE
Contamination Control Guidelines
Obtaining Oil Sample for Analysis {1302, 1348, 3030, 3080, 3278, 4011, 4070, 5050, 5056, 5095, 7542}
Obtaining Oil Sample for Analysis {1302, 1348, 3030, 3080, 3278, 4011, 4070, 5050, 5056, 5095, 7542}
Disassembly and Assembly
Crankcase Ventilator Valve
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Crankcase Guard
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Oil Pan
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
Crankcase Capacity Increased And New Oil Level Gauges Used; Specifications For Conversion Of Existing Gauges{1318,1302}
1980/04/21
Check Oil Level Carefully To Prevent Operation With Too Much Oil In Engine Crankcase{1316}
1981/03/02
Excessive Oil Consumption: Check The Accuracy Of The Oil Level Gauge{1302,1316,1318}
1984/06/04
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Spanner Wrench is Available for Ecology Drain Valves {1302, 1353, 1372, 5076, 5613}
2006/03/20
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
Special Instruction
Use of Piston Pin Bearing Removal and Installation Tools{1218}
Use of Piston Pin Bearing Removal and Installation Tools{1218}
Piston Cleaning Procedure{1214}
Piston Cleaning Procedure{1214}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Technical Information Bulletin
Specifications
Connecting Rod
3208 VEHICULAR ENGINE
Pistons And Rings
3208 VEHICULAR ENGINE
Bearings For Connecting Rods And Mains
3208 VEHICULAR ENGINE
Tool Operating Manual
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
Reuse And Salvage Guidelines
Reuse and Salvage for Connecting Rods {1218}
Reuse and Salvage for Connecting Rods {1218}
Inspection Procedures and Specifications for Pistons and Piston Pins {1214, 1214}
Inspection Procedures and Specifications for Pistons and Piston Pins {1214, 1214}
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
Disassembly and Assembly
Connecting Rod Bearings
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Pistons
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
1980 Caterpillar Remanufactured Products Catalog Is Now Available{0374}
1980/06/23
Top Rings For Pistons Have Two Designs{1215,1214}
1981/07/13
Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18
Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
Carbon Cutting On Piston Top Land {1213,1214}
1982/05/31
List Of Main And Connecting Rod Bearings Currently Available{1203,1219,1230,1226,1227}
1982/06/07
New Bearing Standard: Quantity Of One Part Number Now Has Both Halves Of The Bearing{7551}
1982/08/09
Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08
Use the 6V6167 Contact Point to Measure Wear Steps on Piston Pins{0653}
1982/11/22
New Piston Design Decreases Oil Consumption{1214,1215}
1982/12/20
Parts Service Information For Pistons{1214,1225}
1983/01/31
New Reconditioning Specifications For Cylinders Decrease Piston Scuffing And Seizure {0374,1223,1216,1201}
1983/04/18
Installation Of Bearing For Connecting Rod Piston Pin{1219}
1983/05/09
Reuse Of Engine Bearings{1230}
1983/05/16
New Piston Oil Rings{1215}
1983/09/05
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Parts Service Information For Pistons{1214,1225}
1984/01/09
Remanufactured Connecting Rod Assemblies{1218}
1984/01/23
New Main And Connecting Rod Bearings Have Copper Bond Material{1203,1219,1230}
1984/10/01
Installing New Copper Bonded Bearings Can Extend Engine Life{1230,1203,1219}
1985/04/29
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Increase Piston Reuse With Keystone Piston Ring Gauge Group{1214,1215}
1986/06/16
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
Check Connecting Rods After Engine Failures Involving Hydraulic Lock{1218,1225}
1986/10/20
Improved Main, Thrust And Connecting Rod Bearings Have Aluminum Alloy With More Strength{1230}
1977/10/17
Excessive Oil Consumption Can Be Caused By Dirt In Air Inlet System Or By Flaking Of The Piston Compression Ring{1213,1215}
1977/12/12
Use Only Paint To Mark Connecting Rod Caps For Torque-Turn Method {1218,1219}
1987/06/01
Testing Connecting Rod Eye Bushings When Overhauling Engines{1218}
1987/07/06
Locating Bushings For The 5P3550 Rod Boring Machine Will Now Hold Tapered Piston Pin Bushings {0626}
1978/04/17
Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
5P9705 Tapered Rod Tool Group Used For Removal And Installation Of Piston Pin Bearings In Tapered Connecting Rods{0622,1214,1218}
1979/01/15
New Piston And Connecting Rod Are Tapered In Area Of Piston Pin{1213,1214,1218,1219}
1979/03/05
Connecting Rods For Remanufactured 1160 Truck Engines Changed For Use In Remanufactured 3208 Engines{1218}
1979/03/26
5P3519 Piston Ring Gauge Has Improved Design For Better Accuracy And Easier Use; Corrected Information For Use On Pistons That Have Two Ring Grooves{0653,1214}
1979/05/14
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
New Pistons Used With Two Keystone Compression Rings{1156,1205,1214,1215}
1989/06/19
New Connecting Rod and Main Bearing Kits Available{1230,1203,1219}
1989/10/30
Parts Service Information For Pistons{1214,1225,1331}
1990/05/14
Installation Of Zinc Rods In Caterpillar Marine Engines{1350,1388}
1990/12/24
Verification of Connecting Rod Eye Bushing Retention When Overhauling Engines{1218}
1994/10/31
Piston Ring Groove Gauges To Quickly And Accurately Determine Reusability Of Pistons{1214,0763}
1997/01/13
New Guidelines for Inspecting Pistons {1214}
2006/01/02
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Check The Radiator Fan Spider Assembly When Doing Yearly General Maintenance{1356}
1989/07/24
Engine Coolant Can Be Recycled{1395}
1989/11/13
Special Instruction
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Specifications
Pulley And Damper
3208 VEHICULAR ENGINE
Reuse And Salvage Guidelines
Reuse and Salvage for Cast Iron & Steel Pulleys and Stub Shafts {1205, 1207, 1384, 1425}
Reuse and Salvage for Cast Iron & Steel Pulleys and Stub Shafts {1205, 1207, 1384, 1425}
Disassembly and Assembly
Fan And Fan Drive
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Crankshaft Pulley
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23
Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01
Put Grease On Front Crankshaft Seal Before Installing The Crankshaft Pulley And Damper{1160}
1986/01/13
Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04
Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04
Check Alternator Output Connection Prior To Machine Delivery{1405}
1987/05/18
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
Stronger Idler Pulley Assembly Used With Fan Belts{1358}
1978/05/22
New Design Fan Group Gives Longer Service Life{1356,1359}
1978/12/11
8T5314 Socket Adapter Available To Correctly Install Alternator Pulley Nut {0601}
1988/01/25
New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
New Pistons Used With Two Keystone Compression Rings{1156,1205,1214,1215}
1989/06/19
New Idler Pulley Assembly Used In Air Compressor Group {1803}
1990/02/05
Identification Of External Terminals On Alternators {1405,1406,1400}
1998/12/07
Reuse And Salvage Guidelines
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073}
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073}
Removing and Installing Bushings and Pressure Plates in Hydraulic Gear Pumps {5073}
Removing and Installing Bushings and Pressure Plates in Hydraulic Gear Pumps {5073}
Bench Test Procedures
Bench Test Procedure for Gear Pumps {5073}
Bench Test Procedure for Gear Pumps {5073}
Special Instruction
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Use of Piston Pin Bearing Removal and Installation Tools{1218}
Use of Piston Pin Bearing Removal and Installation Tools{1218}
Using The 4S6553 Engine Evaluation Test Group{0781}
Using The 4S6553 Engine Evaluation Test Group{0781}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Using the 1U5470 Engine Pressure Group{0781}
Using the 1U5470 Engine Pressure Group{0781}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Using the 4C6821 Injection Line Speed Pickup Group{0781}
Using the 4C6821 Injection Line Speed Pickup Group{0781}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Technical Information Bulletin
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
Tool Operating Manual
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
Using the 198-4240 Digital Pressure Indicator Group{0599, 0738, 0788, 1000, 3000, 4000, 5000, 6000}
Using the 198-4240 Digital Pressure Indicator Group{0599, 0738, 0788, 1000, 3000, 4000, 5000, 6000}
Setup and Operation of the 368-8645 Tool Kit (CRANKCASE PRESSURE){1317}
Setup and Operation of the 368-8645 Tool Kit (CRANKCASE PRESSURE){1317}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}
Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}
NEHS0566 <NOBR> 4C-9832</NOBR> Large Engine Roll-Over Stand {0599, 0701}
NEHS0566 4C-9832 Large Engine Roll-Over Stand {0599, 0701}
9U-7370 Belt Tension Tester {0599, 0701}
9U-7370 Belt Tension Tester {0599, 0701}
Using the 143-2099 Sleeve Replacement Tool Group on 3114, 3116, and 3126 Engines{0374, 0599, 0701, 0706, 0781}
Using the 143-2099 Sleeve Replacement Tool Group on 3114, 3116, and 3126 Engines{0374, 0599, 0701, 0706, 0781}
146-1738 Precision Borescope (Hawkeye){0599, 0614, 0644, 0701, 0706, 0708, 0727, 0738}
146-1738 Precision Borescope (Hawkeye){0599, 0614, 0644, 0701, 0706, 0708, 0727, 0738}
Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767}
Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767}
Operating Instructions for 148-2997 Valve Recession Tool Group Used On 3600, G3600, and C175 Engines{0374, 0599, 0701, 0703, 0759}
Operating Instructions for 148-2997 Valve Recession Tool Group Used On 3600, G3600, and C175 Engines{0374, 0599, 0701, 0703, 0759}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
188-3922 Broken Exhaust Bolt and Stud Removal Group for 3114, 3116, 3126, 3126B, 3176, 3176B, C-10, and C12 Engines{0374, 0599, 0701, 0702, 0703}
188-3922 Broken Exhaust Bolt and Stud Removal Group for 3114, 3116, 3126, 3126B, 3176, 3176B, C-10, and C12 Engines{0374, 0599, 0701, 0702, 0703}
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
CRB Valve Spring Testers 8S-2263 and 4C-9496{0374, 0599, 0700, 0701, 1108}
CRB Valve Spring Testers 8S-2263 and 4C-9496{0374, 0599, 0700, 0701, 1108}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
Reuse And Salvage Guidelines
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Reuse and Salvage for Crankshafts {0674, 1202}
Reuse and Salvage for Crankshafts {0674, 1202}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
Cylinder Block Salvage Procedure Using Belzona&reg; 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Service Magazine
Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18
Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03
6V6142 And 6V6143 Installers Can Be Used To Install Crankshaft Seals And Wear Sleeves{0622,0626,1160,1161}
1982/11/01
Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08
Make Change To 6V2100 Multitach And 5P9698 Calibrator{0651}
1982/11/15
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
New Engine Timing Indicator Group Available {0781,0782}
1986/07/07
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
New Special Instruction For Troubleshooting 5P2150 Engine Horsepower Meter{0651,1250}
1977/01/17
Troubleshooting The Tachometer System Of The 4S6553 Engine Instrument Group{0651}
1977/10/10
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20
Procedures And Cautions For Use Of A Flex-Hone On 3204 And 3208 Engines{1201}
1978/06/05
Four New Contact Points Added To 5P6524 Engine Timing Indicator Group{0653}
1978/08/07
Extraction Tools For &quot;Live Oil Sampling&quot;{7770,0770,0781,0783,0784}
1988/04/18
Installation Of Valves For Live Oil Sampling{7770,0770,0781,0783,0784}
1988/06/06
New 6V87 Gauge Measures Valve Stem Wear{0653,1105}
1979/01/08
Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22
6V117 And 6V2001 Bushings Used In 9S8140 Pressurizing Pump Group Are Available For Parts Service{0651}
1979/06/25
Use the 171-7212 Wear Sleeve to Repair the Crankshaft Hub {1160}
2011/09/20
40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16
Spanner Wrench is Available for Ecology Drain Valves {1302, 1353, 1372, 5076, 5613}
2006/03/20
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Information that Improves the Service Life of the Remanufactured Air Conditioning Compressor {1357, 1358, 1397, 1802, 1805, 1809, 7320, 7342, 7343}
2008/03/10
Truck Engine News
Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08
Engine News
Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08
Special Instruction
Installation of Head Gasket (With New Torque Procedure){1100}
Installation of Head Gasket (With New Torque Procedure){1100}
Adaptability of 7C1599 Cylinder Head Gasket{1100}
Adaptability of 7C1599 Cylinder Head Gasket{1100}
Installation Of Remanufactured Cylinder Head Groups{1101}
Installation Of Remanufactured Cylinder Head Groups{1101}
Using The 6V-7770 Valve Guide Kit And 6V-7755 Spring Seat Guide{670, 1104}
Using The 6V-7770 Valve Guide Kit And 6V-7755 Spring Seat Guide{670, 1104}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Installation Of Replacement Cylinder Head Groups (Non-Turbocharged){1101}
Installation Of Replacement Cylinder Head Groups (Non-Turbocharged){1101}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Installation Of Replacement Cylinder Head Assemblies{1101}
Installation Of Replacement Cylinder Head Assemblies{1101}
Installation Of Replacement Cylinder Head Groups (Turbocharged){1101}
Installation Of Replacement Cylinder Head Groups (Turbocharged){1101}
Service Letter-NACD
Product Support Program For Excessive Valve Train Wear On Certain Remanufactured 1160 And 3208 Engines
Product Support Program For Excessive Valve Train Wear On Certain Remanufactured 1160 And 3208 Engines
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Valve Covers
3208 VEHICULAR ENGINE
Valve Rocker Arms And Cam Followers
3208 VEHICULAR ENGINE
Valves<BR> (Engines with Serial Numbers 79V1-79V1407)
3208 VEHICULAR ENGINE
Valves<BR> (Engines with Serial Numbers 79V1408-Up)
3208 VEHICULAR ENGINE
Tool Operating Manual
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767}
Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767}
Operating Instructions for 148-2997 Valve Recession Tool Group Used On 3600, G3600, and C175 Engines{0374, 0599, 0701, 0703, 0759}
Operating Instructions for 148-2997 Valve Recession Tool Group Used On 3600, G3600, and C175 Engines{0374, 0599, 0701, 0703, 0759}
CRB Valve Spring Testers 8S-2263 and 4C-9496{0374, 0599, 0700, 0701, 1108}
CRB Valve Spring Testers 8S-2263 and 4C-9496{0374, 0599, 0700, 0701, 1108}
Service Letter-China
Product Support Program For Excessive Valve Train Wear On Certain Remanufactured 1160 And 3208 Engines
Product Support Program For Excessive Valve Train Wear On Certain Remanufactured 1160 And 3208 Engines
Service Letter-Asia
Reuse And Salvage Guidelines
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Service Letter-APD
Product Support Program For Excessive Valve Train Wear On Certain Remanufactured 1160 And 3208 Engines
Product Support Program For Excessive Valve Train Wear On Certain Remanufactured 1160 And 3208 Engines
Disassembly and Assembly
Valve Covers
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Rocker Shafts And Push Rods
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Rocker Shafts
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Valve Lifters
3208 VEHICULAR ENGINE FOR 613B WHEEL TRACTOR
Service Magazine
High Concentration Of Aluminum In Oil Analysis Can Be The Result Of Rocker Arm Support Wear{1318,1102}
1981/03/02
Lubricant Gives Protection To Camshaft And Roller During Initial Start-Up{1210,1209}
1981/09/21
Use Correct Torque To Prevent Broken Rocker Arm Shafts{1102}
1982/07/05
New Thrust Washer Can Prevent Wrong Oil Sample Readings{1102}
1982/08/23
New Rocker Arm Assemblies Used {1102}
1982/09/13
Improved Cylinder Head Gasket{1101,1201}
1983/01/24
Engine Valve Stem &quot;Use Again&quot; Specifications{0653,1105}
1983/02/28
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1983/10/17
Correct Installation Of New Valve Springs{1108}
1983/11/21
Replacement Valve Guides Can Be Used To Recondition Cylinder Heads{1104}
1983/12/19
Remanufactured Cylinder Head Assemblies{1100,1101}
1984/02/13
Tune-Up Kit And Remanufactured Nozzles Available{1254,1074,1107}
1984/09/03
Remanufactured Cylinder Head Groups{1100,1101,7554}
1984/11/19
Identification Of Camshaft Groups And Valve Mechanism Groups{1210,1102}
1984/11/26
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Check Cylinder Block And Head Flatness Whenever There Is A Head Gasket Failure{1100,1200}
1985/04/01
Head Gasket Replacement Procedure{0350,1100}
1985/08/05
Maximum Wear Limits Established For Camshaft Roller Followers{1209}
1985/09/30
Valve Lash Adjustment Interval Is Changed {1105}
1986/07/07
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures{1209}
1977/05/16
Tools Now Available To Ream And/Or Hone 0.500&quot; (12.70 mm) Diameter Valve Guides{0663}
1977/08/22
Tolerance Added To Valve Clearance Specifications{1105,0374}
1978/01/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1978/01/30
Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/06
Engine Valve Springs Are Now Made Of Carbon Steel Alloy{1101,1108}
1979/02/19
A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads{1105,1101}
1990/10/08
Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Flywheel Housing With 6&deg; Offset Transmission Mounting Holes Must Be Used In GMC Trucks{1000,1157}
1986/06/09
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23

Truck sale:

Caterpillar 613B, Construction
 
Caterpillar 613B, Construction
- Scrapers
NMC
CATERPILLAR 613B 1982
 
CATERPILLAR 613B 1982
- WHEEL TRACTOR SCRAPERS
NMC CAT
11002 Sapp Bros. Dr. - Omaha - Nebrask
CATERPILLAR 613B 1900
 
CATERPILLAR 613B 1900
- WHEEL TRACTOR SCRAPERS
GREGORY POOLE
4807 Beryl Road P. O. Box 469 (27602) - Raleigh
 
USD $8,000 
1977 CAT 613B

ALTORFER INC
Springfield, Illinois
 
 
1972 CAT 613B

Iron Bound Solutions
Texas
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.