AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

7C-6703 TURBOCHARGER GP S/N 60M2883-5160 PART OF 4P-9356, 5N-8530 KIT-ENGINE PARTS, 1N-4776 TURBOCHARGER GP ALSO AN ATTACHMENT 3412


AIR INLET AND EXHAUST SYSTEM
TURBOCHARGER GP
LINES GP-AIR
FUEL SYSTEM
CONTROL GP-GOVERNOR
FILTER GP-FUEL
CONTROL GP-GOVERNOR
CONTROL GP-FUEL RATIO

MARINE ENGINE 3412 MARINE ENGINE 60M
 3412B Marine Engine 60M00001-05160 SEBP1098 3412 60M   (1976)

AIR INLET AND EXHAUST SYSTEM

TURBOCHARGER GP
TURBOCHARGER GP
7C-0693 TURBOCHARGER GP
TURBOCHARGER GP
7C-2731 TURBOCHARGER GP
TURBOCHARGER GP
7C-6703 TURBOCHARGER GP
 

#SEBP10980420
 

7C-6703: TURBOCHARGER GP

7C-6703 TURBOCHARGER GP
S/N 60M2883-5160
PART OF 4P-9356, 5N-8530 KIT-ENGINE PARTS, 1N-4776 TURBOCHARGER GP
ALSO AN ATTACHMENT
i00386785 SEBP1098
7C6703 TURBOCHARGER GP Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-8123 [1] COVER-COMPRESSOR  
3. 2S-1304 [1] CLAMP AS (COMPRESSOR)  
4. 5S-4517 [1] CLAMP AS (TURBINE)  
6. 7C-6705 [1] HOUSING AS (TURBINE)  
7. 3B-0551 [4] PLUG-PIPE  
8. 9L-8412 [7] PLUG-PIPE  
9. 4N-7601 Y [1] CARTRIDGE GP-TURBOCHARGER  
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP10980421
 

7N-0228: VALVE GP-AIR CONTROL

7N-0228 VALVE GP-AIR CONTROL
AN ATTACHMENT
i01424988 SEBP1098
7N0228 VALVE GP-AIR CONTROL Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7N-0227 [1] TUBE AS  
2. 4N-3410 [1] VALVE AS-CONTROL (STARTING)  
3. 5K-9243 [1] ELBOW-FLARED  
4. 6L-3616 [1] CONNECTOR  
5. 7N-0226 [1] TUBE AS  
6. 9S-7703 [2] ELBOW-FLARED  
7. 7N-0015 [1] TUBE AS  
8. 0S-1571 [2] BOLT (3/8-16X1.75-IN)  
9. 3H-2137 [2] LUG  
10. 2B-2404 [4] CLIP  
11. 5M-2894 [2] WASHER-HARD (10.2X18.5X2.5-MM THK)  
12. 7N-0013 [1] TUBE AS  
 

#SEBP10980422
 

5N-3220: ACTUATOR GP-AIR

5N-3220 ACTUATOR GP-AIR -GOVERNOR CONTROL
PART OF 3N-8029, 3N-8146 CONTROL GP-GOVERNOR
AN ATTACHMENT
i00384777 SEBP1098
5N3220 ACTUATOR GP-AIR Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 0S-1619 [4] BOLT (3/8-16X3-IN)  
  3B-4506 [4] LOCKWASHER  
2. 8F-8454 [1] ORIFICE  
3. 1B-4201 [4] NUT-FULL (1/4-28-THD)  
    -OR-
  6V-8185 C [4] NUT (1/4-20-THD)  
4. 5P-0537 C [4] WASHER-HARD (7.2X14.5X2-MM THK)  
5. 9F-0978 [1] CLAMP AS-DIAPHRAGM  
6. 2W-0956 C [1] CLAMP AS-DIAPHRAGM  
7. 3B-4504 [3] LOCKWASHER  
8. 7F-9958 [1] SPRING  
9. 2L-7287 [1] HOUSING-ACTUATOR  
10. 3N-9096 C [1] NUT-RETAINER  
11. 6V-8185 [3] NUT (1/4-20-THD)  
12. 2L-6726 [1] RING-RETAINING  
13. 5N-3219 [1] SHAFT  
14. 011-3580 C [2] SETSCREW-SQUARE HEAD  
15. 5K-0906 [1] BOLT (5/16-18X0.625-IN)  
  3F-9556 [1] LOCKWASHER  
16. 2N-6005 [1] SPRING  
17. 2L-6744 [1] PLUNGER  
18. 2L-7289 [1] HOUSING-END  
19. 112-5360 [1] DIAPHRAGM  
20. 9F-0981 [1] GUIDE-DIAPHRAGM  
21. 6V-8801 C [2] NUT (3/8-16-THD)  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP10980423
 

295-1571: BRACKET GP-MOUNTING

295-1571 BRACKET GP-MOUNTING
AN ATTACHMENT
i02849534 SEBP1098
2951571 BRACKET GP-MOUNTING Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2F-4967 [2] SPACER (10.5X19X5.512-MM THK)  
2. 8N-3971 [1] BRACKET AS-FUEL FILTER  
3. 0T-0065 [1] BOLT (3/8-16X3.5-IN)  
4. 3B-1915 [1] BOLT (3/8-16X1.375-IN)  
5. 4B-4043 [4] BOLT (5/8-11X1.375-IN)  
6. 5M-2894 [2] WASHER-HARD (10.2X18.5X2.5-MM THK)  
7. 5P-8247 [4] WASHER-HARD (17X32X3.5-MM THK)  
 

#SEBP10980424
 

4L-6460: CABLE AS-GOVERNOR CONTROL

4L-6460 CABLE AS-GOVERNOR CONTROL
POSITIVE LOCK
FIELD INSTALLATION
i01506927 SEBP1098
4L6460 CABLE AS-GOVERNOR CONTROL Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
    (NO SERVICED PARTS)
 

#SEBP10980425
 

1W-5889: CONTROL GP-FUEL RATIO

1W-5889 CONTROL GP-FUEL RATIO
Type 1
FOR USE WITH 746 KW MARINE ENGINE
AN ATTACHMENT
i00352602 SEBP1098
1W5889 CONTROL GP-FUEL RATIO Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8L-5008 [1] ELBOW-PIPE  
2. 3N-7268 EI [1] HOSE AS (142CM)  
3. 8M-2773 [2] CLIP (LOOP)  
4. 1B-2790 [2] BOLT (5/16-18X1.375-IN)  
  9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
5. 9L-5125 [1] ELBOW  
6. 4N-8112 [2] BOLT (5/16-18X3.250-IN)  
  8F-7242 [2] WASHER (8.7X15.9X1.6-MM THK)  
  3B-4505 [2] LOCKWASHER  
7. 2P-8643 [1] GASKET  
8. 2W-6808 CY [1] CONTROL GP-FUEL RATIO  
  C   CHANGE FROM PREVIOUS TYPE
  E   ORDER BY THE CENTIMETER
  I   REFER TO HYDRAULIC INFORMATION SYSTEM
  Y   SEPARATE ILLUSTRATION
 

#SEBP10980426
 

1W-5889: CONTROL GP-FUEL RATIO

1W-5889 CONTROL GP-FUEL RATIO
Type 2
FOR USE WITH 746 KW MARINE ENGINE
AN ATTACHMENT
i00352604 SEBP1098
1W5889 CONTROL GP-FUEL RATIO Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8L-5008 [1] ELBOW-PIPE  
2. 3N-7268 I [1] HOSE AS  
3. 8M-2773 [2] CLIP (LOOP)  
4. 1B-2790 [1] BOLT (5/16-18X1.375-IN)  
5. 9M-1974 [1] WASHER-HARD (8.8X16X2-MM THK)  
6. 2N-1287 [1] ELBOW-FLARED  
7. 2P-8643 [1] GASKET  
8. 2W-3157 Y [1] CONTROL GP-FUEL RATIO  
9. 4N-8112 [2] BOLT (5/16-18X3.250-IN)  
10. 3B-4505 [2] LOCKWASHER  
11. 8F-7242 [2] WASHER (8.7X15.9X1.6-MM THK)  
  I   REFER TO HYDRAULIC INFORMATION SYSTEM
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP10980427
 

2W-3157: CONTROL GP-FUEL RATIO

2W-3157 CONTROL GP-FUEL RATIO
S/N 60M2038-4457
PART OF 6N-6209, 8N-5021 CONTROL GP-FUEL RATIO
i00107869 SEBP1098
2W3157 CONTROL GP-FUEL RATIO Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2P-8939 [1] VALVE (FUEL CHECK)  
2. 6V-2627 [3] BOLT-12 POINT HEAD  
  9S-5282 [3] WASHER-HARD (8.8X14.5X2-MM THK)  
3. 4J-2506 [1] SEAL-O-RING  
4. 6L-5766 [1] GASKET  
5. 2P-8226 [1] COVER-DIAPHRAGM  
6. 1W-4797 [1] DIAPHRAGM  
7. 2P-8875 [1] RETAINER AS  
8. 6N-0515 [1] SPRING (INNER)  
9. 7N-5715 [1] PIN  
10. 2P-8225 [1] HOUSING-DIAPHRAGM  
11. 2W-3156 [1] VALVE AS-LIMITER (FUEL RATIO CONTROL)  
12. 7N-8512 [1] SEAL  
13. 1W-2567 [1] RETAINER-SPRING  
14. 7N-0209 [1] SPRING (OUTER)  
15. 2P-8803 [1] WASHER (1.094X1.883X0.036-IN THK)  
16. 4B-3388 [2] BOLT (5/16-18X1.125-IN)  
  8F-7242 [2] WASHER (8.7X15.9X1.6-MM THK)  
17. 6N-0513 [1] SPRING  
18. 6N-7148 [1] COVER  
 

#SEBP10980428
 

2W-3157: CONTROL GP-FUEL RATIO

2W-3157 CONTROL GP-FUEL RATIO
S/N 60M4458-5160
PART OF 1W-5889, 8N-5021 CONTROL GP-FUEL RATIO
ALSO AN ATTACHMENT
i00107870 SEBP1098
2W3157 CONTROL GP-FUEL RATIO Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2W-3156 [1] VALVE AS-LIMITER (FUEL RATIO CONTROL)  
2. 2P-8225 [1] HOUSING-DIAPHRAGM  
3. 4P-1639 C [1] SEAL-CONTROL  
4. 4P-0246 C [1] VALVE (FUEL CHECK)  
5. 1W-2567 [1] RETAINER-SPRING  
6. 7N-0209 [1] SPRING (OUTER)  
7. 6N-0515 [1] SPRING (INNER)  
8. 110-2469 [1] EXTENSION  
9. 124-4668 [1] GASKET-FUEL RATIO CONTROL  
10. 125-8828 [1] COVER-FUEL RATIO CONTROL  
11. 9S-8748 [1] NUT-FULL (1/4-28-THD)  
12. 110-2468 [1] RETAINER  
13. 2P-8226 [1] COVER-DIAPHRAGM  
14. 6N-0513 [1] SPRING  
15. 2P-8803 [1] WASHER (1.094X1.883X0.036-IN THK)  
16. 1W-4797 [1] DIAPHRAGM  
17. 5B-7040 [3] BOLT (1/4-20X1-IN)  
18. 5P-0537 [3] WASHER-HARD (7.2X14.5X2-MM THK)  
19. 4B-3388 [2] BOLT (5/16-18X1.125-IN)  
20. 8T-4224 [2] WASHER-HARD (8.8X16X2-MM THK)  
21. 9N-1754 C [1] SPRING  
22. 3E-6760 [1] SEAL-O-RING  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP10980429
 

2W-6808: CONTROL GP-FUEL RATIO

2W-6808 CONTROL GP-FUEL RATIO
PART OF 1W-5889 CONTROL GP-FUEL RATIO
AN ATTACHMENT
i00360004 SEBP1098
2W6808 CONTROL GP-FUEL RATIO Parts scheme
  For full view, you need register

Parts for your 3412 MARINE ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2P-8939 [1] VALVE  
2. 9S-5282 [3] WASHER-HARD (8.8X14.5X2-MM THK)  
3. 4J-2506 [1] SEAL-O-RING  
4. 6L-5766 [1] GASKET  
5. 2P-8226 [1] COVER-DIAPHRAGM  
6. 1W-4797 [1] DIAPHRAGM  
7. 2P-8875 [1] RETAINER AS  
8. 6N-0515 [1] SPRING (INNER)  
9. 7N-8512 [1] SEAL  
10. 2P-8225 [1] HOUSING-DIAPHRAGM  
11. 2W-3156 [1] VALVE AS-LIMITER  
12. 6V-2627 [3] BOLT-12 POINT HEAD  
13. 1W-2567 [1] RETAINER-SPRING  
14. 7N-0209 [1] SPRING (OUTER)  
15. 2P-8803 [1] WASHER (1.094X1.883X0.036-IN THK)  
16. 4B-3388 [2] BOLT (5/16-18X1.125-IN)  
  8F-7242 [2] WASHER (8.7X15.9X1.6-MM THK)  
17. 6N-0513 [1] SPRING  
18. 6N-7148 [1] COVER  
19. 7N-5715 [1] PIN  
 

Information:

Engine News
Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning
1979/08/22
New Basic Turbocharger Group Prevents Possible Failures Of Compressor Wheel
1981/11/25
Stronger Turbine Wheel Used In Turbocharger Shaft And Wheel Assemblies
1982/08/25
Use Of 9S3265 Retaining Compound On AiResearch Turbocharger Compressor Wheel Retainer Nuts
1983/04/27
Special Instructions Packaged With Turbocharger Cartridge Repair Kits May Be Incorrect
1986/02/01
Stop Engine If There Is A Turbocharger Bearing Failure
1987/04/01
Be Sure To Correctly Tighten Turbocharger Clamp Assemblies
1987/09/01
Tightening Procedure For Turbocharger Compressor Nut
1989/09/01
New Bolt Improves Retention Of Backplate To Housing Assembly In Turbocharger Cartridge Groups
1991/04/01
"Off-Size" Bearing Kits Available
1991/10/01
Compressor Nut Torque For Schwitzer Turbochargers
1993/07/01
Water Cooled Turbine Housings May Require Larger Core Plugs{1065,1050}
1994/11/01
Adapter For Disassembly And Assembly Of Turbocharger Cartridge
1977/01/28
Clip Now Used To Hold Coolant Line For The Turbocharger
1977/03/15
Changes To Retainer Nut Torque And Assembly Procedures For Turbocharger Compressor Wheels
1977/03/15
Silicone Grease Now Used In Seal Ring Groove In Turbochargers
1978/05/24
Improved Seal Rings For Turbine End Of Turbochargers
1978/07/05
Salvage Of Turbocharger Compressor Housing During Reconditioning
1978/10/18
A Revised Special Instruction Provides Information on Service Replacement of the Turbocharger (for Turbocharged Engines Only) {1052}
2003/03/01
Policy for Reusing the Turbocharger Turbine Housing {1052, 1065, 7754}
2003/07/01
Prevent the Possibility of Contamination in order to Ensure Longer Life of Turbochargers {1052}
2003/12/01
Magnetic Cover for the Turbocharger Oil Supply Line {1052, 1307}
2006/02/20
New Gaskets for the Turbocharger Oil Lines are Now Used {1052, 1307}
2005/07/04
Packaging the Turbocharger {1052}
2007/02/26
Troubleshooting the Wastegate Canister {1052, 1057}
2008/12/22
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Special Instruction
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
2W726 Turbocharger Cartridge Repair Kit{1053}
2W726 Turbocharger Cartridge Repair Kit{1053}
2W727 Turbocharger Cartridge Repair Kit{1053}
2W727 Turbocharger Cartridge Repair Kit{1053}
2W715 Turbocharger Cartridge Repair Kit{1053}
2W715 Turbocharger Cartridge Repair Kit{1053}
7W4874 Turbocharger Cartridge Repair Kit{1053}
7W4874 Turbocharger Cartridge Repair Kit{1053}
Instructions for the Service Replacement of the Turbochargers{1052}
Instructions for the Service Replacement of the Turbochargers{1052}
Proper Remanufactured Turbocharger Housing Adjustment and Alignment for Caterpillar Engines {1052, 1053}
Proper Remanufactured Turbocharger Housing Adjustment and Alignment for Caterpillar Engines {1052, 1053}
Specifications
Air An Exhaust Lines
3412 INDUSTRIAL AND MARINE ENGINES
Turbocharger Impeller Installation
3412 INDUSTRIAL AND MARINE ENGINES
Turbocharger T12
3412 INDUSTRIAL AND MARINE ENGINES
Turbocharger TW81
3412 INDUSTRIAL AND MARINE ENGINES
Turbocharger TV81
3412 INDUSTRIAL AND MARINE ENGINES
Turbocharger TW91
3412 INDUSTRIAL AND MARINE ENGINES
Turbochargers F452, F555 & F552
3412 INDUSTRIAL AND MARINE ENGINES
Turbochargers 4MFW and 4MF
3412 INDUSTRIAL AND MARINE ENGINES
Turbocharger
3408C and 3412C Marine Engines
Reuse And Salvage Guidelines
Reuse and Salvage for Turbochargers {0760, 0767, 1052}
Reuse and Salvage for Turbochargers {0760, 0767, 1052}
Information Release Memo
CATERPILLAR REMAN PRODUCTS GROUP ANNOUNCES EXPANDED TURBOCHARGER COVERAGE FOR CERTAIN ENGINE MODELS
CATERPILLAR REMAN PRODUCTS GROUP ANNOUNCES EXPANDED TURBOCHARGER COVERAGE FOR CERTAIN ENGINE MODELS
CAT REMAN ANNOUNCES AN ADVANCED SALVAGE TECHNIQUE WHICH WILL AFFECT THE APPEARANCE OF CERTAIN TURBOCHARGERS
CAT REMAN ANNOUNCES AN ADVANCED SALVAGE TECHNIQUE WHICH WILL AFFECT THE APPEARANCE OF CERTAIN TURBOCHARGERS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Disassembly and Assembly
Turbocharger
3408C & 3412C MARINE ENGINES
Turbocharger (Industrial Engine)
3412 INDUSTRIAL & MARINE ENGINES
Turbocharger (Marine Engine)
3412 INDUSTRIAL & MARINE ENGINES
Turbocharger (T12)
3412 INDUSTRIAL & MARINE ENGINES
Turbocharger
3412 INDUSTRIAL & MARINE ENGINES
Service Magazine
Remove Piston Cooling Tubes Before Removal Of Pistons And Connecting Rods{1214,1218,1201,1225,1307}
1981/07/13
New Basic Turbocharger Group Prevents Possible Failures Of Compressor Wheel{1052}
1981/11/09
Carbon Build-Up In Combustion And Inlet Areas{1058,1101,1105,1214,1104}
1982/03/22
Stronger Turbine Wheel Used In Turbocharger Shaft And Wheel Assemblies{1053,1052}
1982/06/14
Caterpillar Recommends Against The Use Of Alcohol Mist Injection Systems{1050,1250}
1982/06/28
Use Care When Handling Turbocharger Compressor Wheels{1052,1077}
1985/12/16
Special Instructions Packaged With Turbocharger Cartridge Repair Kits May Be Incorrect{1053}
1986/02/03
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Adapter For Disassembly And Assembly Of Turbocharger Cartridge{0620,1053}
1977/01/24
Clip Now Used To Hold Coolant Line For The Turbocharger{1052,1380}
1977/02/28
Changes To Retainer Nut Torque And Assembly Procedures For Turbocharger Compressor Wheels{0374,1052}
1977/02/28
Stop Engine If There Is A Turbocharger Bearing Failure{1052,1318}
1987/04/06
Be Sure To Correctly Tighten Turbocharger Clamp Assemblies{1052}
1987/09/07
Silicone Grease Now Used In Seal Ring Groove In Turbochargers{1052,1053,1077}
1978/05/15
Improved Seal Rings For Turbine End Of Turbochargers{1052}
1978/07/03
Salvage Of Turbocharger Compressor Housing During Reconditioning{1052}
1978/10/09
Use Of 9S3265 Retaining Compound On Schwitzer Turbocharger Compressor Wheel Retainer Nuts{1052,1053}
1979/06/25
Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20
Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/09/03
6V2055 High Vacuum Grease Gives Better Oil Seal {1052,1053,1077,0682}
1979/09/10
Different Thrust Bearing And Thrust Rings Now Used In Turbochargers{1052,1053}
1979/10/22
Tightening Procedure For Turbocharger Compressor Nut{1052,1060}
1989/09/18
New Bolt Improves Retention Of Backplate To Housing Assembly In Turbocharger Cartridge Groups{1052,1053,1056,7553}
1991/04/08
New Plug And O-Ring Can Help Prevent Oil Leakage At The Flywheel Housing Gasket{1157,1307}
1992/09/21
Compressor Nut Torque For Schwitzer Turbochargers{1052}
1993/07/26
Troubleshooting the Wastegate Canister {1052, 1057}
2008/12/22
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}

Caterpillar Parts SIS Catalog 3412 :

TURBOCHARGER GP
7C-2731 TURBOCHARGER GP
TURBOCHARGER GP
7C-0693 TURBOCHARGER GP
TURBOCHARGER GP
7C-0693 TURBOCHARGER GP
TURBOCHARGER GP
6N-7972 TURBOCHARGER GP
TURBOCHARGER GP
6N-7963 TURBOCHARGER GP
TURBOCHARGER GP
6N-7963 TURBOCHARGER GP
TURBOCHARGER GP
6N-2931 TURBOCHARGER GP
TURBOCHARGER GP
6N-2020 TURBOCHARGER GP
VALVE GP-AIR CONTROL
7N-0228 VALVE GP-AIR CONTROL
ACTUATOR GP-AIR
5N-3220 ACTUATOR GP-AIR
BRACKET GP-MOUNTING
295-1571 BRACKET GP-MOUNTING
CABLE AS-GOVERNOR CONTROL
4L-6460 CABLE AS-GOVERNOR CONTROL
CONTROL GP-FUEL RATIO
1W-5889 CONTROL GP-FUEL RATIO
CONTROL GP-FUEL RATIO
1W-5889 CONTROL GP-FUEL RATIO
CONTROL GP-FUEL RATIO
2W-3157 CONTROL GP-FUEL RATIO
CONTROL GP-FUEL RATIO
2W-3157 CONTROL GP-FUEL RATIO

Truck sale:

Caterpillar 3412, mobile generator sets, Construction
95,720 
Caterpillar 3412, mobile generator sets, Construction
- mobile generator sets
FINANZAUTO S.A.
Caterpillar 3412, mobile generator sets, Construction
96,795 
Caterpillar 3412, mobile generator sets, Construction
- mobile generator sets
FINANZAUTO S.A.
Caterpillar 3412, mobile generator sets, Construction
93,569 
Caterpillar 3412, mobile generator sets, Construction
- mobile generator sets
FINANZAUTO S.A.
Caterpillar 3412, Stationary Generator Sets, Construction
60,000 
Caterpillar 3412, Stationary Generator Sets, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY
Caterpillar 3412, Stationary Generator Sets, Construction
159,600 
Caterpillar 3412, Stationary Generator Sets, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.