AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

6N4654 FUEL RATIO CONTROL GP PART OF 6N6268 GOVERNOR & FUEL INJECTION PUMP AN ATTACHMENT 3304 INDUSTRIAL ENGINE


FUEL SYSTEM
GOVERNOR GP
TORQUE CONTROL GP
GOVERNOR GP

INDUSTRIAL ENGINE 3304 INDUSTRIAL ENGINE 04B
 3304 INDUSTRIAL ENGINE 04B14449-26768 SEBP1194 3304 04B   (1968)

FUEL SYSTEM

GOVERNOR GP
DRIVE GP-GOVERNOR
7N-2595 DRIVE GP-GOVERNOR
DRIVE GP-GOVERNOR
7N-2595 DRIVE GP-GOVERNOR
CONTROL GP-FUEL RATIO
6N-4654 CONTROL GP-FUEL RATIO
CONTROL GP-GOVERNOR
4N-4601 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
1N-5331 CONTROL GP-GOVERNOR
GOVERNOR SPRINGS
 

#SEBP11940430
 

6N-4654: CONTROL GP-FUEL RATIO

6N4654 FUEL RATIO CONTROL GP
PART OF 6N6268 GOVERNOR & FUEL INJECTION PUMP
AN ATTACHMENT
c213636 SEBP1194
6N4654 CONTROL GP-FUEL RATIO Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6L-5764 [1] COVER-ADJUSTMENT  
2. 6L-5766 [1] GASKET  
3. 6N-1606 [1] SPRING  
4. 6L-5769 [1] WASHER  
5. 6N-1603 [1] HOUSING AS  
6. 6N-1602 [1] BEARING-SLEEVE  
7. 9N-0866 [1] BOLT-CONTROL ADJUSTABLE  
8. 4S-7458 [1] DIAPHRAGM  
9. 2N-5919 [3] BOLT  
10. 4F-7957 [2] BOLT  
11. 5S-6120 [1] RETAINER AS  
12. 6L-5767 [1] COVER-DIAPHRAGM  
13. 6N-7523 C [5] WASHER  
14. 5S-6458 [1] DOWEL  
15. 6N-0968 [1] SPRING  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP11940431
 

6N-3730: TORQUE CONTROL GP

6N3730 TORQUE CONTROL GP
AN ATTACHMENT
c152565 SEBP1194
6N3730 TORQUE CONTROL GP Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4L-6458 [1] NUT  
2. 4L-7124 [1] BOLT  
3. 4N-3882 [1] CONTACT  
4. 8M-9064 [1] SHIM .064 in.(1.63 mm) thick  
5. 1P-6452 [2] INSULATOR  
6. 9L-7235 [3] SHIM .039 in.(1 mm) thick  
7. 4N-7777 [3] SPACER .010 in.(0.26 mm) thick  
8. 4N-9098 [1] SPACER .500 in.(12.70 mm) thick  
9. 1P-6453 [1] BAR  
10. 9S-9662 [1] SPRING .018 in.(0.46 mm) thick  
11. 8L-8601 [6] SPACER .002 in.(0.06 mm) thick  
12. 9L-9347 [1] SHIM .020 in.(0.51 mm) thick  
 

#SEBP11940432
 

4N-4601: CONTROL GP-GOVERNOR

4N4601 GOVERNOR CONTROL GP-POSITIVE LOCK
4N3830 GOVERNOR CONTROL-PAGE 143
AN ATTACHMENT
c544612 SEBP1194
4N4601 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-3830 Y [1] CONTROL GP-GOVERNOR  
2. 2B-2694 [2] BOLT  
3. 6N-0254 [1] SPACER  
  Y   SEPARATE ILLUSTRATION
 

#SEBP11940433
 

1N-5331: CONTROL GP-GOVERNOR

1N5331 GOVERNOR CONTROL GP
AN ATTACHMENT
c125824 SEBP1194
1N5331 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 5L-3946 [1] ROD END  
2. 5L-3934 [1] HUB-ADJUSTABLE LEVER  
3. 1B-2578 [1] NUT  
 

#SEBP11940434
 

GOVERNOR SPRINGS

GOVERNOR SPRINGS
AN ATTACHMENT
SEBP11940434 SEBP1194
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
   
   
  4N-4222 GOVERNOR SPRING  
    5% REGULATION AT 2000 R.P.M.
   
  4N-4224 GOVERNOR SPRING  
    5% REGULATION AT 2000 R.P.M.
   
  6N-7814 GOVERNOR SPRING  
    5% REGULATION AT 1800 R.P.M.
   
  6N-7815 GOVERNOR SPRING  
    5% REGULATION AT 1500 R.P.M.
 

#SEBP11940435
 

8N-2177: CONTROL GP-GOVERNOR

8N2177 GOVERNOR CONTROL GP
PROVIDES 3-HOLE GOVERNOR CONTROL LEVER
AN ATTACHMENT
c220760 SEBP1194
8N2177 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1M-1254 [1] BOLT  
2. 3N-4892 [1] LEVER-GOVERNOR CONTROL  
 

#SEBP11940436
 

8N-0917: CONTROL GP-GOVERNOR

8N0917 GOVERNOR CONTROL GP-TYPE 1
4N3828-PAGE 144
AN ATTACHMENT
c225345 SEBP1194
8N0917 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-3828 Y [1] CONTROL GROUP  
    (Separate Illustration)
2. 6N-0768 [2] SCREW  
3. 6N-0254 [1] SPACER  
4. 8N-0816 [1] BRACKET  
5. 030-7622 [1] SPACER  
6. 7F-1906 [1] CLIP  
7. 8N-0075 [1] DAMPER  
8. 1B-2790 [1] BOLT  
  1D-4716 [1] NUT  
  9M-1974 [2] WASHER  
9. 8N-0815 [1] SUPPORT ASSEM.  
10. 7G-8802 [1] MOTOR ASSEM.  
11. 7B-2742 [1] BOLT  
12. 5P-0537 [3] WASHER  
13. 1H-8289 [4] SCREW  
  3K-9089 [4] NUT  
14. 0S-1615 [2] BOLT  
  7H-8909 [2] LOCKNUT  
15. 8N-0076 [1] LEVER  
16. 7L-4186 [2] ROD END  
17. 1A-8285 [2] NUT  
18. 6B-0607 [1] BOLT  
19. 7N-8008 [1] SWITCH (Governor Control)  
  3L-4576 [1] NAMEPLATE  
  F [1] WIRING DIAGRAM  
  Y   SEPARATE ILLUSTRATION
  F   NOT SHOWN
 

#SEBP11940437
 

8N-0917: CONTROL GP-GOVERNOR

8N0917 GOVERNOR CONTROL GP-TYPE 2
4N3828-PAGE 144
AN ATTACHMENT
c330847 SEBP1194
8N0917 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-3828 Y [1] CONTROL GP-GOVERNOR  
2. 6N-0768 [2] SCREW-MACHINE  
3. 6N-0254 [1] SPACER  
4. 8N-0816 [1] BRACKET  
5. 030-7622 [1] SPACER-GENERATOR MOUNTING  
6. 7F-1906 [1] CLIP  
7. 8N-0075 [1] DAMPER  
8. 1B-2790 [1] BOLT  
  1D-4716 [1] NUT-FULL  
  9M-1974 [2] WASHER  
9. 8N-0815 [1] SUPPORT AS-MOTOR  
10. 7N-8008 [1] SWITCH AS (GOV. CONT.)  
  3L-4576 [1] NAMEPLATE  
11. 7B-2742 [1] BOLT  
12. 5P-0537 [3] WASHER  
13. 1H-8289 [4] SCREW-MACHINE  
  3K-9089 [4] NUT-SELF LOCKING  
14. 9F-6580 C [2] BOLT  
  7H-8909 [2] LOCKNUT  
15. 8N-0076 [1] LEVER-GOVERNOR  
16. 7L-4186 [2] ROD END-BEARING  
17. 1A-8285 [2] NUT-JAM  
18. 6B-0607 [1] BOLT-STUD  
19. 4W-7773 C [1] MOTOR AS  
  7G-8802 [1] MOTOR-GEAR  
20. 7N-9738 [1] HOUSING-RECEPTACLE  
  7N-7779 [1] SOCKET  
  7N-7780 [1] PIN-CONNECTOR  
21. 8F-6302 C [1] BOLT  
  F [1] DIAGRAM-WIRING  
  C   CHANGE FROM PREVIOUS TYPE
  F   NOT SHOWN
  Y   SEPARATE ILLUSTRATION
 

#SEBP11940438
 

4N-4599: CONTROL GP-GOVERNOR

4N4599 GOVERNOR CONTROL GP-REMOTE & POSITIVE LOCK
4N3828 GOVERNOR CONTROL-PAGE 144
AN ATTACHMENT
c577605 SEBP1194
4N4599 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-3828 Y [1] CONTROL GP-GOVERNOR  
2. 2B-2694 [2] BOLT  
3. 6N-0254 [1] SPACER  
  Y   SEPARATE ILLUSTRATION
 

#SEBP11940439
 

4N-3830: CONTROL GP-GOVERNOR

4N3830 GOVERNOR CONTROL GP-POSITIVE LOCKING
PART OF 4N4601 GOVERNOR
AN ATTACHMENT
c510948 SEBP1194
4N3830 CONTROL GP-GOVERNOR Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4W-2541 [1] SHAFT-GOVERNOR CONTROL  
2. 4N-4523 [1] HANDLE AS  
  4N-9029 [1] WASHER  
3. 4W-2542 [1] SPRING  
4. 4N-4520 [1] GUIDE  
5. 5K-0605 [1] PLUG  
6. 8L-4282 [1] HUB  
7. 6N-0775 C [1] RATCHET-GOVERNOR CONTROL  
  C   CHANGE FROM PREVIOUS TYPE
 

Information:

Engine News
A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing
1979/01/24
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.
1979/05/09
New Seal Used Under Retaining Bushing For Fuel Injection Pump Bonnet
1979/08/22
Improvements Made To Fuel Injection Pump And Governor Group
1979/11/28
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1981/04/01
Explanation Of Differences In Timing Advance Information
1981/08/26
Timing Pin Removed From Governor And Fuel Injection Pump Group; Change To Service Manuals
1981/09/16
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier
1982/11/10
New Seal Used On Governor Control Shaft
1982/12/15
Service Information For Woodward Governors
1983/10/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1984/01/18
New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage
1984/06/20
Fill Oil Sump Before Installing Woodward Governor
1985/01/16
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
New Gaskets Help Prevent Leaks From Fuel System Governors{1264}
1991/12/01
Pressure Compensated Simple Governor (PSG Governor) Changes From Aluminum To Cast Iron Housing {1264}
1995/04/01
Governor Spring Guide Press Depth {1287,1284}
1996/01/17
Governor Control Cover Assembly Includes New Seal And Improved Cover{1264}
1997/07/01
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
A New Exhaust Manifold And Fuel Pump Heat Shield Is Used On Industrial Engines That Have A Woodward Governor With An Electric Motor
1978/07/05
Improved Guide Pin For Fuel Injection Pump Lifters
1978/08/30
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N628 Bearing{7551, 1253}
Installation Of 8N628 Bearing{7551, 1253}
Technical Information Bulletin
3300 Engine Timing Measurement For Reduced Emissions And Improved Engine Performance/Life
3300 Engine Timing Measurement For Reduced Emissions And Improved Engine Performance/Life
Specifications
Fuel Injection Equipment
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump<BR> (4N4864)
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump<BR> (7L543 and 2N8603)
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Governor
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Woodward PSG Governors
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Output Shaft Governor<BR> (8L8661)
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Equipment
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Adjustable &quot;Dashpot&quot;<BR> (Close Regulation Type Governor)
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel System Timing<BR> (Engines With Timing Pointer)
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Automatic Timing Advance Unit
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Woodward PSG Governor
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Woodward PSG Governor<BR> (8N6774)
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Governor Control
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Fuel Transfer Pump
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing And Governor
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Governor
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Adapter Housing And Levers
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing And Governor
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Check Valve And Bypass Valve
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Governor
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pumps
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Fuel Injection Nozzle Assembly Used{1254}
1980/01/21
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23
FT1632 Bolt Used During Removal Of Sleeve From Sleeve Metering Fuel System{0621,1251,1253}
1981/08/31
Timing Pin Removed From Governor And Fuel Injection Pump Group; Change To Service Manuals {1286}
1981/09/14
New Torque Specification For Bushing{0374,1253,1251}
1982/01/18
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Modification Of 2P8315 Bracket Assembly{0652,1286}
1982/08/16
6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier{1206,1272,0614}
1982/11/08
New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1983/12/05
New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14
Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
A New Exhaust Manifold And Fuel Pump Heat Shield Is Used On Industrial Engines That Have A Woodward Governor With An Electric Motor{1059,1250,1289}
1978/05/29
Improved Guide Pin For Fuel Injection Pump Lifters{1251}
1978/08/21
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
New Tachometer Drive Adapter Has Increased Service Life{7462,1288}
1979/01/22
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.{1253}
1979/05/07
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
New Seal Used Under Retaining Bushing For Fuel Injection Pump Bonnet{1251,1253,1286}
1979/08/13
New Gaskets Help Prevent Leaks From Fuel System Governors{1264}
1991/12/02
New Fuel Pump Drive Idler Gear Assembly And Shaft Used In Front Timing Gear Groups {1206}
1993/06/14

Caterpillar Parts SIS Catalog 3304 :

TORQUE CONTROL GP
6N-0509 TORQUE CONTROL GP
DRIVE GP-GOVERNOR
7N-2595 DRIVE GP-GOVERNOR
DRIVE GP-GOVERNOR
7N-2595 DRIVE GP-GOVERNOR
PUMP GP-FUEL INJECTION
1W-5495 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
1W-5491 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6N-0129 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6N-0129 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6N-0129 PUMP GP-FUEL INJECTION
TORQUE CONTROL GP
6N-3730 TORQUE CONTROL GP
CONTROL GP-GOVERNOR
4N-4601 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
1N-5331 CONTROL GP-GOVERNOR
GOVERNOR SPRINGS
CONTROL GP-GOVERNOR
8N-2177 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
8N-0917 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
8N-0917 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
4N-4599 CONTROL GP-GOVERNOR

Truck sale:

Caterpillar 303/304 20 HD BUCKET, bucket, Construction
854 
Caterpillar 303/304 20 HD BUCKET, bucket, Construction
- bucket
MILTON CAT
 
30,000 
Caterpillar 3304B, Stationary Generator Sets, Construction


Caterpillar 3304B, Stationary Generator Sets, Construction
30,000 
Caterpillar 3304B, Stationary Generator Sets, Construction

FOLEY EQUIPMENT COMPANY
Caterpillar 303/304 ADAPTER SSL TO MHE, Schnellwechsler, Bau-Und Bergbauausrüstung
650 
Caterpillar 303/304 ADAPTER SSL TO MHE, Schnellwechsler, Bau-Und Bergbauausrüstung
- Quick connectors
MILTON CAT
Caterpillar 3304, Stationäre Stromaggregate, Bau-Und Bergbauausrüstung
17.000 
Caterpillar 3304, Stationäre Stromaggregate, Bau-Und Bergbauausrüstung
- Stationary Generator Sets
EMPIRE MACHINERY
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.