9S7947 HAND TOOL GROUP 8F9866 GREASE GUN PARTS ARE SHOWN ON PAGE 218 AN ATTACHMENT D398B GEN SET ENGINE



SERVICE EQUIPMENT AND SUPPLIES
TOOLS
GASKET & SEAL KITS
TOOLS
CHARTS & FILMS

GEN SET ENGINE D398B GEN SET ENGINE 35Z
 D398B GENERATOR SET ENGINE 35Z00001-UP SEBP1290 D398B 35Z   (1980)

SERVICE EQUIPMENT AND SUPPLIES

TOOLS
HAND TOOL GROUP
9S-7947 HAND TOOL GROUP
GREASE GUN AS
8F-9866 GREASE GUN AS
 

#SEBP12900650
 

9S-7947: HAND TOOL GROUP

9S7947 HAND TOOL GROUP
8F9866 GREASE GUN PARTS ARE SHOWN ON PAGE 218
AN ATTACHMENT
c568304 SEBP1290
9S7947 HAND TOOL GROUP Parts scheme
  For full view, you need register

Parts for your D398B GEN SET ENGINE:

Pos. Part No Qty Parts name Comments
1. 1U-7267 [1] SCREWDRIVER (PHILLIPS)  
2. 1U-7264 [1] SCREWDRIVER (FLAT BLADE)  
3. 1U-7115 [1] RATCHET-REVERSE ROUND  
4. 1U-7118 [1] EXTENSION (1/2"X10"LONG)  
  1U-7119 [1] EXTENSION (1/2"X5"LONG)  
5. 8F-9866 Y [1] GREASE GUN AS (LEVER)  
6. 2P-8250 [1] WRENCH AS-STRAP  
7. 5S-9568 [1] SOCKET-DRAIN PLUG  
8. 5P-1763 C [1] SOCKET-PETCOCK  
9. 1U-7234 [1] GAUGE-FEELER  
10. 5F-4764 [1] PRY BAR  
11. 1U-7053 [1] WRENCH (5/16 OPENING)  
  1U-7054 [1] WRENCH (3/8 OPENING)  
  1U-7056 [1] WRENCH (1/2 OPENING)  
  1U-7057 [1] WRENCH (9/16 OPENING)  
  1U-7058 [1] WRENCH (5/8 OPENING)  
  1U-7060 [1] WRENCH (3/4 OPENING)  
  1U-7062 [1] WRENCH (7/8 OPENING)  
  1U-7064 [1] WRENCH (1 IN OPENING)  
12. 1U-7099 [1] SOCKET (1/2 OPENING)  
  1U-7102 [1] SOCKET (9/16 OPENING)  
  1U-7107 [1] SOCKET (7/8 OPENING)  
  1U-7108 [1] SOCKET (15/16 OPENING)  
  1U-7109 [1] SOCKET (1 IN OPENING)  
  1U-7111 [1] SOCKET (1-1/8 OPENING)  
13. 5S-9569 [1] SOCKET (DRAIN PLUG)  
14. 9U-7509 [1] PLIERS  
15. 9U-6219 [1] TOOL BOX  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

#SEBP12900651
 

GASKET KITS

GASKET KITS
SEBP12900651 SEBP1290
  For full view, you need register

Parts for your D398B GEN SET ENGINE:

Pos. Part No Qty Parts name Comments
   
   
  6V-3746 VALVE GRINDING  
  6V-3747 VALVE GRINDING-SINGLE HEAD  
  6V-3749 CENTRAL & LOWER STRUCTURE  
  5P-8970 SINGLE CYLINDER LINER  
  6V-3740 FRONT STRUCTURE  
  6V-3741 REAR STRUCTURE  
  6V-3748 MANIFOLD  
  6V-3743 WATER PUMP  
  6V-3745 WATER LINES-TO BE USED WITH NEW OR  
    EXCHANGE WATER PUMP
  6V-3737 AFTERCOOLER & AFTERCOOLER LINES  
  6V-3736 TURBOCHARGER MOUNTING  
  6V-3742 FUEL SYSTEM  
  6V-3744 OIL COOLER & LINES  
  6V-3739 OIL PUMP  
 

#SEBP12900652
 

8F-9866: GREASE GUN AS

8F9866 GREASE GUN
PART OF 9S7947 HAND TOOL GROUP SHOWN ON PAGE 217. AN ATTACHMENT
c108355 SEBP1290
8F9866 GREASE GUN AS Parts scheme
  For full view, you need register

Parts for your D398B GEN SET ENGINE:

Pos. Part No Qty Parts name Comments
1. 9F-2636 [1] NOZZLE AS  
2. 2M-2689 [1] COUPLER AS  
3. 9F-2638 [1] HOSE AS  
4. 9F-2637 [1] NIPPLE  
 

#SEBP12900653
 

5N-9206: PLATE & FILM GP

5N9206 ACCESSORY PLATE AND DECAL GROUP
AN ATTACHMENT
SEBP12900653 SEBP1290
  For full view, you need register

Parts for your D398B GEN SET ENGINE:

Pos. Part No Qty Parts name Comments
   
   
  1P-2807 [4] FILM-SYMBOL  
   
  3N-9344 [4] FILM-SYMBOL  
   
  5N-9207 [2] PLATE-WARNING  
   
  3N-8591 [4] DECAL LIFTING WARNING  
 

#SEBP12900654
 

NAME PLATES & TRANSFERS

NAME PLATES & TRANSFERS
SEBP12900654 SEBP1290
  For full view, you need register

Parts for your D398B GEN SET ENGINE:

Pos. Part No Qty Parts name Comments
   
   
  1H-4950 [2] PLATE-WARNING  
    ON L.H. FRONT SIDE COVER AND R.H.
    CENTER SIDE COVER
   
  8L-4345 [1] PLATE-MANIFOLD DIAGRAM  
    ON REAR OF R.H. MANIFOLD WATER SHIELD
   
  9L-6531 [1] PLATE-CAUTION & INFORMATION  
    ON VALVE COVER
   
  3N-3790 [1] PLATE-SERIAL NUMBER  
    ON R.H. SIDE OF CYLINDER BLOCK
   
  4B-4158 [2] DRIVE SCREW  
   
  7M-9576 [1] TRANSFER-SAE STANDARD ENGINE ROTATION  
    ON REAR OF R.H.FLYWHEEL HOUSING WATER
    PASSAGE
   
  4N-9346 [2] TRANSFER-D398 CAT  
    ON R.H. & L.H. FRONT INTAKE MANIFOLD
   
  8L-9765 [1] FILM-WARNING  
    ON FUEL FILTER HOUSING
   
  4W-2696 [1] FILM-HYDRA MECHANICAL SHUT-OFF  
    ON ENGINE OIL COOLER
 

Information:

Truck Engine News
New Infrared Thermometer Has Narrow, 50:1 Target Ratio, Wide Temperature Range {0776, 1350, 3000, 4000, 4150, 4250}
2006/03/27
Engine News
New 6V2120 Spline Sprocket Improves Depth Control Of 5P4175 Boring Tool Group
1980/05/14
6V3147 Main Bearing Wrench Now Available
1980/11/12
6V3150 Engine Pressure Group And 6V3121 Multitach Group Are Available For Testing Engines
1981/01/28
Changes Have Been Made To Caterpillar Service Literature
1981/03/04
Instruction Cards For "Go-No Go" Gauges Now Available
1981/07/01
New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group
1982/02/10
New Engine Testing And Adjusting Tools Give More Accuracy And Longer Service Life
1982/02/24
Use 6V6035 Hardness Tester On Crankshafts
1982/02/24
Use The 6V6059 Microlite With The 6V2196 Inspection Microscope
1982/04/07
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/04/07
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach
1982/05/12
New Address For Repair Of Diagnostic Tools
1982/06/16
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
Separate Valve Stem Gauges Available
1982/08/25
Dial Bore Gauge And Size Setting Fixture Available
1982/09/22
Service Information For Easier Use Of The 6V3100 Timing Indicator Group
1982/10/20
Make Change To 6V2100 Multitach And 5P9698 Calibrator
1982/12/15
Use FT1711 Light Table For Cylinder Liner Inspection
1982/12/15
New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip
1982/12/15
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
Use The 6V5000 Infrared Thermometer Group To Measure Temperatures
1983/04/27
New Service Centers For 6V3100 Engine Timing Indicator Group
1983/10/26
Hunting Down The Cheaters
1985/06/01
Fuel Sulfur Analyzer Available
1986/01/01
Oil Total Base Number (TBN) Test Kit Available
1986/02/01
New Engine Timing Indicator Group Available
1986/07/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity
1986/11/01
Check For Dirt Before Replacing Pyrometer Switch
1987/01/01
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups
1987/03/01
Check For Plugged Orifices In Mechanical Pressure Gauges
1987/03/01
5P957 And 5P3514 Coolant And Battery Tester
1987/04/01
Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems
1987/05/01
Two New Self-Powered Digital Tachometers And Signal Generator Available
1987/05/01
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group
1987/07/01
Fluid Sampling Tools For Nonpressurized Compartments
1988/03/01
Extraction Tools For "Live Oil Sampling"
1988/05/01
New Service Tools Available
1988/10/01
4C4213 Insulation Tester for Electrical Power Generation
1989/12/01
New 4C5084 Oil Filter Cutter Replaces Former 6V7905 Filter Cutter
1990/11/01
New Adapter Group For Use With Fuel Injection Test Bench
1977/06/22
5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster
1978/01/18
Replacement Seal Group For Water Pump Impeller Now Has All The Seal Parts Plus An Installation Tool
1978/03/01
New 5P8709 Piston Tool Group For The Alignment Of Piston Cooling Jets
1978/05/03
Caterpillar Electronic Technician (Cat ET) 2001B-Service Pack 1 Software Upgrade is Now Available {0785}
2002/02/01
Calibration Fluid for Fuel Nozzle Test Equipment Is Available {0782, 1251, 1254, 1290, 1713}
2008/11/17
Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Special Instruction
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}
Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}
Using The 5P-4150 Nozzle Testing Group{0782}
Using The 5P-4150 Nozzle Testing Group{0782}
Using The 4S6553 Engine Evaluation Test Group{0781}
Using The 4S6553 Engine Evaluation Test Group{0781}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569}
6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4950 Injection Line Speed Pickup Group{0782}
Using The 6V4950 Injection Line Speed Pickup Group{0782}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}
Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}
Using The 6V9450 Engine Pressure Group{781}
Using The 6V9450 Engine Pressure Group{781}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Using The 8T1000 Position Indicator Group{0760, 0762}
Using The 8T1000 Position Indicator Group{0760, 0762}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Using the 1U6602 Photo-Tach Group{0775}
Using the 1U6602 Photo-Tach Group{0775}
Using the 1U5470 Engine Pressure Group{0781}
Using the 1U5470 Engine Pressure Group{0781}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Using the 4C6821 Injection Line Speed Pickup Group{0781}
Using the 4C6821 Injection Line Speed Pickup Group{0781}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Operation And Maintenance Of 1P3060 Pyrometer Group{0776}
Operation And Maintenance Of 1P3060 Pyrometer Group{0776}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4840 Tool Group To Install Water Ferrules{1201}
Use Of 6V4840 Tool Group To Install Water Ferrules{1201}
Using The 6V7899 Size Setting Fixture Group{651}
Using The 6V7899 Size Setting Fixture Group{651}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Tool and Specification Chart for Inverted Duo-Cone Seals {0599, 7561}
Tool and Specification Chart for Inverted Duo-Cone Seals {0599, 7561}
Using Caterpillar Replacement Thread Inserts {0676}
Using Caterpillar Replacement Thread Inserts {0676}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Operating Instructions for Cat 1U-9400 Series Hydraulic Test Center {0784}
Operating Instructions for Cat 1U-9400 Series Hydraulic Test Center {0784}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474}
Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Tool Operating Manual
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
Instructions for 1U9801 Ultrasonic Wear Indicator Program Module Replacement{0767}
Instructions for 1U9801 Ultrasonic Wear Indicator Program Module Replacement{0767}
Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}
Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}
358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684}
358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684}
Crimputer III Setup and Operation{0684, 5057}
Crimputer III Setup and Operation{0684, 5057}
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
NEHS1126: <NOBR>370-8570</NOBR> Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
<NOBR>439-3938</NOBR>, <NOBR>439-3939</NOBR>, <NOBR>439-3940</NOBR>, <NOBR>439-3941</NOBR>, <NOBR>439-3942</NOBR>, <NOBR>439-3943</NOBR> Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}
439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}
NEHS0566 <NOBR> 4C-9832</NOBR> Large Engine Roll-Over Stand {0599, 0701}
NEHS0566 4C-9832 Large Engine Roll-Over Stand {0599, 0701}
Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}
Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}
Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}
Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
456-4449 Support Device{0374, 0599, 0629, 0632, 0700}
456-4449 Support Device{0374, 0599, 0629, 0632, 0700}
Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}
Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}
464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}
General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}
General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
Zip-Tie Installation Guide{0374, 0599, 7000}
Zip-Tie Installation Guide{0374, 0599, 7000}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}
Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}
Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}
Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}
Reuse And Salvage Guidelines
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Dynamometer Testing of Caterpillar Engines {0781, 1000}
Dynamometer Testing of Caterpillar Engines {0781, 1000}
Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685}
Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685}
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Crimputer III Setup and Operation{0684, 5057}
Crimputer III Setup and Operation{0684, 5057}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Fundamentals of HVOF Spray for Reconditioning Components {0599, 0679, 1000, 7000}
Fundamentals of HVOF Spray for Reconditioning Components {0599, 0679, 1000, 7000}
Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}
Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}
Cleaning Components with Carbon Dioxide (CO<SUB>2</SUB>) {0680, 1000, 7000}
Cleaning Components with Carbon Dioxide (CO2) {0680, 1000, 7000}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Cylinder Block Salvage Procedure Using Belzona&reg; 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Shop Review
Engine Component Racks
Engine Component Racks
Engine Stands
Engine Stands
Bench Test Procedures
Dynamometer Testing of Caterpillar Engines {0781, 1000}
Dynamometer Testing of Caterpillar Engines {0781, 1000}
Technical Analysis
Technical Analysis 1 (TA1) Visual Inspection for Generator Sets {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Generator Sets {0372, 1000, 7000, 753S, 7565}
Service Magazine
6V3147 Main Bearing Wrench Now Available{1203,0612}
1980/11/10
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18
New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group{0622,1217}
1982/01/25
New Engine Testing And Adjusting Tools Give More Accuracy And Longer Service Life{0651}
1982/02/01
Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22
Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03
Separate Valve Stem Gauges Available{0653,1000}
1982/06/07
New Address For Repair Of Diagnostic Tools{0650}
1982/06/14
6V6124 Calibration Coil Available To Calibrate And Check 6V4910 AC/DC Clamp-On Ammeter{0651}
1982/06/28
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Vacuum Tester Checks For Leaks Between Valve Face and Seat{0651,1103,1105}
1982/09/06
Dial Bore Gauge And Size Setting Fixture Available{0653}
1982/09/20
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08
Make Change To 6V2100 Multitach And 5P9698 Calibrator{0651}
1982/11/15
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
New Engine Timing Indicator Group Available {0781,0782}
1986/07/07
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Use Gas Detector Tubes That Have Expired Dates To &quot;Break In&quot; The Combustion Chambers For The Fuel Sulphur Analyzer Group{0651}
1986/11/10
Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15
New Special Instruction For Troubleshooting 5P2150 Engine Horsepower Meter{0651,1250}
1977/01/17
New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17
New 5P7307 Engine Turning Tool Group Fits All Engines{0611}
1977/02/14
New Adapter Group For Use With Fuel Injection Test Bench{0652}
1977/06/13
Tools Now Available To Ream And/Or Hone 0.500&quot; (12.70 mm) Diameter Valve Guides{0663}
1977/08/22
Troubleshooting The Tachometer System Of The 4S6553 Engine Instrument Group{0651}
1977/10/10
Fabricated Extension Prevents Fuel &quot;Splash&quot; During Injection Valve Testing{0650,1254}
1977/10/17
Assembly Procedure For The 5P4721 Tube (Part Of The 5P4149 Conversion Group And 5P4150 Nozzle Testing Group){0650}
1977/10/24
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23
Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems {0774,1250,1300,1350}
1987/05/11
The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11
Two New Self-Powered Digital Tachometers And Signal Generator Available {7462}
1987/05/11
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20
5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster{0621,1216}
1978/01/09
Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06
Replacement Seal Group For Water Pump Impeller Now Has All The Seal Parts Plus An Installation Tool{1361,0622}
1978/02/13
5P4149 Conversion Group To Become A Discontinued Item On October 1, 1978{0650,1254}
1978/03/27
Locating Bushings For The 5P3550 Rod Boring Machine Will Now Hold Tapered Piston Pin Bushings {0626}
1978/04/17
Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
5P8626 Tool Bit Available To Machine The 5P6595 And 5P8607 Liner Seat Inserts{0664}
1978/06/12
New 5P8744 Adapter Assembly And Special Instruction Procedures For 5P4150 Nozzle Tester Group{0650}
1978/08/28
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
4J7533 O-Ring Seals Now Available For Parts Service Of The 5P4150 Nozzle Tester Group{0651}
1978/10/09
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Extraction Tools For &quot;Live Oil Sampling&quot;{7770,0770,0781,0783,0784}
1988/04/18
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23
Installation Of Valves For Live Oil Sampling{7770,0770,0781,0783,0784}
1988/06/06
New Frequency Meter Has Replaceable Voltage Droop Resistor{7471}
1988/08/08
Improved Pressure Gauge Sender Used{7450,7485}
1988/11/21
Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12
New 6V87 Gauge Measures Valve Stem Wear{0653,1105}
1979/01/08
Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
6V183 Gasket Now Available For Parts Service To Use On 5P4150 Or 8S2242 Nozzle Tester{0651}
1979/06/25
Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02
Caution Label Added To 5P4150 Nozzle Testing Group{0651}
1979/07/09
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Splash Shields Added To Caterpillar Fuel Injection Test Bench{0652}
1979/08/13
Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
Fast Fuel Delivery Couplings And Fast Oil Change Couplings Are Available For All Caterpillar Equipment{0671,1273,1279,1325}
1979/10/08
Use The 6V2034 Micrometer Adapter To Measure Lip Thickness Of Engine Valves {0653,1105}
1979/10/29
4C4213 Insulation Tester for Electrical Power Generation{0785}
1989/12/11
New Temperature Regulators; Regulator Service Hours Changed{1330,0770,1355,7527,7543}
1990/10/15
New Hydraulic Wrenches and Pumps {0602, 0615}
2000/06/05
Diagnostic Cables and Harnesses Are Available {0785}
2014/08/11
Thermocouple Assembly (Exhaust) Measures Engine Exhaust Temperatures {0701, 0776, 0781}
2004/03/29
40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16
Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562}
Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562}
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
A New Tool Operating Manual for Proper Zip-Tie Installation Is Now Available for All Caterpillar Products {0374, 0599, 7000}
2015/08/10
Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}

Caterpillar Parts SIS Catalog D398B :

3N-9146 KIT-MARINE SPARE PARTS
5N-3725 KIT-MARINE SPARE PARTS
CONNECTION GP-ELECTRICAL
7C-2561 CONNECTION GP-ELECTRICAL
CONNECTION GP-TERMINAL STRIP
7C-1435 CONNECTION GP-TERMINAL STRIP
CONNECTION GP-TERMINAL STRIP
9Y-0903 CONNECTION GP-TERMINAL STRIP
CONNECTION GP-GENERATOR LEADS
9Y-0873 CONNECTION GP-GENERATOR LEADS
CONTROL GP-ELECTRONIC
5N-0591 CONTROL GP-ELECTRONIC
CONNECTION GP-GENERATOR LEADS
4W-3727 CONNECTION GP-GENERATOR LEADS
GASKET KITS
GREASE GUN AS
8F-9866 GREASE GUN AS
5N-9206 PLATE & FILM GP
NAME PLATES & TRANSFERS

Truck sale:

Caterpillar D398BIN, Construction
80,000 
Caterpillar D398BIN, Construction
- Industrial engines
FOLEY EQUIPMENT COMPANY
1982 CAT D398B
USD $87,000 
1982 CAT D398B

Foley Equipment Company
Topeka Area, Kansas
CAT D398B
USD $35,000 
CAT D398B

Industrial Motor Power
Burbank, California