AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

9N8062 GOVERNOR AND FUEL PUMP DRIVE GROUP 3208 TRUCK ENGINE


FUEL SYSTEM
GOVERNOR GP
ELECTRICAL AND STARTING SYSTEM
STARTING AID GP
FUEL SYSTEM
LINES GP-FUEL

TRUCK ENGINE 3208 TRUCK ENGINE 32Y
 3208 TRUCK ENGINE 32Y68441-UP IHC SEBP1309 3208 32Y   (1978)

FUEL SYSTEM

GOVERNOR GP
GOV & FUEL INJ PUMP GP
8N-5642 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
8N-5642 GOV & FUEL INJ PUMP GP
DRIVE GP-GOVERNOR & FUEL PUMP
9N-8062 DRIVE GP-GOVERNOR & FUEL PUMP
DRIVE GP-GOVERNOR & FUEL PUMP
9N-0740 DRIVE GP-GOVERNOR & FUEL PUMP
 

#SEBP13090170
 

9N-8062: DRIVE GP-GOVERNOR & FUEL PUMP

9N8062 GOVERNOR AND FUEL PUMP DRIVE GROUP
c227058 SEBP1309
9N8062 DRIVE GP-GOVERNOR & FUEL PUMP Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-5022 C [1] WASHER  
2. 4N-2968 [1] GEAR  
3. 9N-3874 C [1] GEAR & WEIGHT ASSEM. (69 teeth)  
4. 8S-7499 [1] PIN  
5. 5M-7516 [1] SCREW  
6. 9L-7034 [1] WASHER  
7. 9N-1856 [1] SHAFT ASEEM.  
    (Includes)
8. 9L-9236 [1] SLEEVE  
  C   INDICATES CHANGE
 

#SEBP13090171
 

9N-0740: DRIVE GP-GOVERNOR & FUEL PUMP

9N0740 GOVERNOR AND FUEL PUMP DRIVE GROUP
c230521 SEBP1309
9N0740 DRIVE GP-GOVERNOR & FUEL PUMP Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-5022 C [1] WASHER-HARD  
2. 7N-6644 C [1] GEAR-FUEL PUMP DRIVE (69 TEETH)  
3. 9N-3873 C [1] GEAR & WEIGHT AS (69 TEETH)  
4. 8S-7499 [1] PIN-SPRING  
5. 5M-7516 [1] SCREW-MACHINE  
6. 9L-7034 [1] WASHER  
7. 9N-1856 C [1] SHAFT AS-TACH DRIVE  
8. 9L-9236 [1] SLEEVE-TACH DRIVE  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP13090172
 

9N-3771: INJECTION GP-CETANE

9N3771 CETANE INJECTION GROUP-FIELD INSTALLATION-TYPE 1
NOTE: REDUCES WHITE SMOKE WHEN STARTING ENGINE IN COLD TEMPERATURES
c218068 SEBP1309
9N3771 INJECTION GP-CETANE Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-3335 [2] STRAP  
2. 4B-1248 [2] SCREW-MACHINE  
  4B-2051 [2] NUT  
  4B-4674 [4] WASHER  
3. 9N-3334 [1] TANK AS  
4. 9N-3336 [1] CAP AS  
5. 8L-5000 [1] SWITCH-PUSH (START)  
6. 9N-3828 [1] HARNESS AS-WIRING  
  5P-5623 D WIRE 6.2M(242IN)  
7. 1S-9593 [3] STRAP-CABLE  
8. 2L-8075 [2] TERMINAL  
9. 031-5637 [1] HOLDER-FUSE  
  3P-8989 [1] FUSE  
10. 2L-8076 [1] TERMINAL  
11. 6N-9587 [1] CONNECTOR  
12. 7G-1018 [1] CONTROL GP-ELECTRONIC  
13. 5P-5009 [1] REDUCER-FLARED  
14. 031-5894 [1] TEE  
15. 3J-7354 [3] SEAL-O-RING  
16. 9N-3770 [1] ORIFICE  
17. 9L-8791 [1] SOLENOID  
18. 030-6984 [1] CONNECTOR-FLARED  
19. 031-7224 I [1] HOSE AS  
  5P-0733 D HOSE 2.5M(98.4IN)  
20. 001-6285 [2] COUPLING  
21. 8L-6557 [1] CONNECTOR  
22. 9N-3778 [1] FILTER AS-FUEL  
23. 5H-7826 [1] NIPPLE-PIPE  
24. 053-3567 [2] BRACKET  
  9N-3620 F [1] FILM-INSTRUCTION (LOCATED ON DASH)  
  9N-3621 F [1] FILM-CAUTION (LOCATED ON TANK)  
  D   ORDER BY THE METER
  F   NOT SHOWN
  I   SEE HOSE FABRICATION GUIDE
 

#SEBP13090173
 

9N-3771: INJECTION GP-CETANE

9N3771 CETANE INJECTION GROUP-FIELD INSTALLATION-TYPE 2
NOTE: REDUCES WHITE SMOKE WHEN STARTING ENGINE IN COLD TEMPERATURES
c317586 SEBP1309
9N3771 INJECTION GP-CETANE Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-3335 [2] STRAP  
2. 4B-1248 [2] SCREW-MACHINE  
  4B-2051 [2] NUT  
  4B-4674 [4] WASHER  
3. 9N-3334 [1] TANK AS  
4. 9N-3336 [1] CAP AS  
5. 8L-5000 [1] SWITCH-PUSH (START)  
6. 9N-3828 [1] HARNESS AS-WIRING  
  5P-5623 BD WIRE (16 GAUGE)  
7. 1S-9593 [3] STRAP-CABLE  
8. 2L-8075 [2] TERMINAL  
9. 031-5637 [1] HOLDER-FUSE  
  3P-8989 [1] FUSE (2 AMP)  
10. 2L-8076 [1] TERMINAL  
11. 6N-9587 [1] CONNECTOR  
12. 7G-1018 [1] CONTROL GP-ELECTRONIC  
13. 5P-5009 [1] REDUCER-FLARED  
14. 031-5894 [1] TEE  
15. 3J-7354 [3] SEAL-O-RING  
16. 9N-3770 [1] ORIFICE  
17. 9L-8791 [1] SOLENOID  
18. 030-6984 [1] CONNECTOR-FLARED  
19. 031-7224 I [1] HOSE AS  
  5P-0733 D HOSE 2.5M(98.4IN)  
20. 001-6285 [2] COUPLING  
21. 8L-6557 [1] CONNECTOR  
22. 9N-3778 [1] FILTER AS-FUEL  
23. 1P-4022 C [2] FITTING  
24. 053-3567 [2] BRACKET  
25. 1P-4278 C [2] CLAMP  
26. 5P-0733 CD HOSE .20M(7.87IN)  
27. 8J-1256 C [2] CLIP  
28. 7D-1553 C [1] CLIP  
   
  9N-3620 F [1] FILM-INSTRUCTION  
    (LOCATED ON DASH)
  9N-3621 F [1] FILM-CAUTION  
    (LOCATED ON TANK)
  B   USE AS REQUIRED
  C   CHANGE FROM PREVIOUS TYPE
  D   ORDER BY THE METER
  F   NOT SHOWN
  I   SEE HOSE FABRICATION GUIDE
 

#SEBP13090174
 

9N-3771: INJECTION GP-CETANE

9N3771 CETANE INJECTION GROUP-FIELD INSTALLATION-TYPE 3
NOTE: REDUCES WHITE SMOKE WHEN STARTING ENGINE IN COLD TEMPERATURES
c329373 SEBP1309
9N3771 INJECTION GP-CETANE Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-3335 [2] STRAP  
2. 4B-1248 [2] SCREW-MACHINE  
  4B-2051 [2] NUT  
  4B-4674 [4] WASHER  
3. 9N-3334 [1] TANK AS  
4. 9N-3336 [1] CAP AS  
5. 8L-5000 [1] SWITCH-PUSH (START)  
6. 9N-3828 [1] HARNESS AS-WIRING  
  5P-5623 BD WIRE (16 GA)  
7. 1S-9593 [3] STRAP-CABLE  
8. 2L-8075 [2] TERMINAL  
9. 031-5637 [1] HOLDER-FUSE  
  3P-8989 [1] FUSE (2 AMP)  
10. 2L-8076 [1] TERMINAL  
11. 6N-9587 [1] CONNECTOR  
12. 7G-1018 [1] CONTROL GP-ELECTRONIC  
13. 5P-5009 [1] REDUCER-FLARED  
14. 8T-2543 C [1] TEE-O-RING PORT  
15. 3J-7354 C [1] SEAL-O-RING  
16. 7W-1539 C [1] ORIFICE  
17. 9L-8791 [1] SOLENOID  
18. 030-6984 [1] CONNECTOR-FLARED  
19. 031-7224 [1] HOSE AS  
  5P-0733 BD HOSE  
20. 001-6285 [2] COUPLING  
21. 8L-6557 [1] CONNECTOR  
22. 9N-3778 [1] FILTER AS-FUEL  
23. 1P-4022 [2] FITTING  
24. 053-3567 [2] BRACKET  
25. 1P-4278 [2] CLAMP  
26. 5P-0733 BD HOSE  
27. 8J-1256 [2] CLIP  
28. 7D-1553 [1] CLIP  
29. 1J-9671 C [3] SEAL-O-RING  
  9N-3620 F [1] FILM-INSTRUCTION  
    (LOCATED ON DASH)
  9N-3621 F [1] FILM-CAUTION  
    (LOCATED ON TANK)
  B   USE AS REQUIRED
  C   CHANGE FROM PREVIOUS TYPE
  D   ORDER BY THE METER
  F   NOT SHOWN
 

#SEBP13090175
 

9N-3880: LINES GP-FUEL INJECTION

9N3880 FUEL INJECTION LINES GROUP-PART 1 OF 2
SERIAL NO. 32Y68441 TO 32Y99999 INCLUSIVE AND 51Z1 TO 51Z449 INCLUSIVE
c337579 SEBP1309
9N3880 LINES GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9L-6047 [1] LINE AS-FUEL INJ (NO 7)  
2. 9L-6045 [1] LINE AS-FUEL INJ (NO 5)  
3. 9N-1374 [1] LINE AS-FUEL INJ (NO 4)  
4. 9L-6046 [1] LINE AS-FUEL INJ (NO 6)  
5. 9L-9372 [4] LOCK-ADAPTER  
6. 9L-6048 [1] LINE AS-FUEL INJ (NO 8)  
7. 1W-2459 C [8] CLAMP AS-NOZZLE  
8. 9N-3879 [8] SPACER-CLAMP  
9. 9N-3979 R [8] NOZZLE AS-FUEL INJ  
    (EACH INCLUDES)
  1H-1023 [2] SEAL-O-RING  
  9N-3738 [1] WASHER-PLAIN  
10. 9L-9098 [1] SEAL-CARBON STOP  
11. 9L-7675 [8] ADAPTER AS-LINE  
    (EACH INCLUDES)
12. 6F-4855 [1] SEAL-O-RING  
13. 9N-0863 [1] LINE AS-FUEL INJ (NO 3)  
14. 9L-6042 [1] LINE AS-FUEL INJ (NO 2)  
15. 9N-0861 [1] LINE AS-FUEL INJ (NO 1)  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMFG PART MAY BE AVAILABLE
 

#SEBP13090176
 

9N-3880: LINES GP-FUEL INJECTION

9N3880 FUEL INJECTION LINES GROUP-PART 2 OF 2
SERIAL NO. 32Y68441 TO 32Y99999 INCLUSIVE AND 51Z1 TO 51Z449 INCLUSIVE
c227151 SEBP1309
9N3880 LINES GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-2050 [1] BRACKET  
2. 5P-4939 [16] SCREW AS-MACHINE  
3. 9L-8715 [3] CLAMP  
4. 9L-8716 [4] CLAMP (TAPPED)  
5. 9L-8713 [3] CLAMP-FUEL LINE  
6. 9L-8714 [6] CLAMP-FUEL LINE (TAPPED)  
7. 9L-9160 [3] CLAMP AS-LINE  
8. 9L-9251 [1] CLIP  
  9M-1974 [1] WASHER  
9. 9N-2064 [1] TUBE AS-BLEED  
10. 5P-3395 [1] ELBOW  
11. 8L-8413 [6] STRAP-CABLE  
12. 7K-8332 [1] INSERT-TUBE SUPPORT  
  6H-3687 F [8] PROTECTIVE CAP (FUEL NOZZLE TIP)  
  9L-7663 F [8] PROTECTIVE PLUG (FUEL NOZZLE INLET)  
  F   NOT SHOWN
 

#SEBP13090177
 

9N-3880: LINES GP-FUEL INJECTION

9N3880 FUEL INJECTION LINES GROUP
SERIAL NO. 51Z450-UP
2W0770 AND 2W3398-PAGES 103B AND 103D
c337580 SEBP1309
9N3880 LINES GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2W-0770 CY [1] LINES GROUP  
2. 2W-3398 CY [1] LINES GROUP  
3. 9L-7675 [8] ADAPTER ASSEM  
    (EACH INCLUDES)
4. 6F-4855 [1] SEAL  
5. 1W-5829 CR [8] NOZZLE ASSEM  
    (EACH INCLUDES)
  1H-1023 [2] SEAL  
  9N-3738 [1] WASHER  
6. 9L-9098 [1] SEAL  
7. 1W-2459 [8] CLAMP ASSEM.  
8. 9N-3879 [8] SPACER  
9. 9L-9372 [4] LOCK  
10. 9N-2064 [1] TUBE ASSEM.  
11. 7K-8332 [1] INSERT  
12. 9L-9251 [1] CLIP  
13. 9M-1974 [1] WASHER  
14. 9N-2050 [1] BRACKET  
15. 9L-8716 [1] CLAMP (TAPPED)  
16. 5P-4939 [1] SCREW ASSEM.  
  R   REMFG PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
  C   INDICATES CHANGE
 

#SEBP13090178
 

2W-0770: LINES GP-FUEL INJECTION

2W0770 FUEL INJECTION LINES GROUP
SERIAL NO. 51Z450-UP
PART OF 9N3880 FUEL INJECTION LINES
c306386 SEBP1309
2W0770 LINES GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9L-6047 [1] LINE AS-FUEL INJ (NO. 7)  
2. 9L-6045 [1] LINE AS-FUEL INJ (NO. 5)  
3. 9L-8715 [1] CLAMP  
4. 9L-8716 [1] CLAMP  
5. 5P-4939 [3] SCREW AS-MACHINE  
6. 9L-9160 [1] CLAMP AS-LINE  
7. 9L-8714 [1] CLAMP-FUEL LINE  
 

#SEBP13090179
 

2W-3398: LINES GP-FUEL INJECTION

2W3398 FUEL INJECTION LINES GROUP
SERIAL NO. 51Z450-UP
PART OF 9N3880 FUEL INJECTION LINES
c496689 SEBP1309
2W3398 LINES GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9L-6048 [1] LINE AS-FUEL INJ (NO. 8)  
2. 9L-8715 [2] CLAMP  
3. 9L-8716 [2] CLAMP  
4. 9L-6046 [1] LINE AS-FUEL INJ (NO. 6)  
5. 5P-4939 B [12] SCREW AS-MACHINE  
6. 9L-9160 [2] CLAMP AS-LINE  
7. 9L-8714 B [5] CLAMP-FUEL LINE  
8. 9N-1374 [1] LINE AS-FUEL INJ (NO. 4)  
9. 9L-6042 [1] LINE AS-FUEL INJ (NO. 2)  
10. 9N-0861 [1] LINE AS-FUEL INJ (NO. 1)  
11. 9N-0863 [1] LINE AS-FUEL INJ (NO. 3)  
12. 9L-8713 B [3] CLAMP-FUEL LINE  
  B   USE AS REQUIRED
 

Information:

Truck Engine News
New Governor Spring Available For Specific Engine Applications
1981/03/06
Clean Electrical Contacts In Exhaust Gas Recirculation (e.g.r.) Switch Group And Cover Assembly Before Installation
1981/04/09
Electrical Information For Egr (exhaust Gas Recirculation) Systems On 3208 Truck Engines So Equipped
1981/04/09
Check All Settings When Fuel Injection Pump Group Is Installed
1981/04/09
New 6V3060 EGR System Tester Group Available
1981/05/12
Some Parts Books And Microfiche Show Wrong Governor And Fuel Pump Drive Groups For Specific Engines
1981/08/18
Bent Lever For Fuel Shut-off Solenoid Can Cause Low Engine Performance
1982/02/17
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/03/31
New Gasket Used In Governor And Fuel Injection Pump Group
1982/03/31
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/09/01
FT1698 Driver Can Be Used For Reconditioning Of Governor Housing
1982/10/27
New Seal Used On Governor Control Shaft
1982/12/08
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/23
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1983/12/21
Governor Flyweight Shield No Longer Used In New Scroll Fuel Systems
1985/01/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps
1987/11/01
Check Valve Added To Keep Air From Entering Fuel System
1988/10/01
Governor Springs For Sleeve Metering Fuel Systems
1990/05/01
Dowel Hole Removed From 8N3946 Governor Housing Improves Service Life
1991/07/01
New Spring Used In Governor Control Groups
1992/04/01
New Hold-Down Bolts For The Sleeve Metering Fuel System (SMFS) Governor Housing {1251}
1996/09/01
Engine News
A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing
1979/01/24
Improvements Made To Fuel Injection Pump And Governor Group
1979/03/14
New Pistons And Timing Advance Unit Give Better Emissions Control And Easier Starts
1979/04/04
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.
1979/05/09
Timing Advance Mechanism Used In Certain 3208 Truck Engines In Ford Trucks
1979/08/08
New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group
1979/08/22
Important: Use Only 12 Volts Direct Current To Boost Start 3208 Truck Engines Equipped With Exhaust Gas Recirculation Systems
1980/04/09
Low Emission Truck Engines With Exhaust Gas Recirculation (EGR) Systems
1977/01/28
Drains In New Fuel Injection Pump Housing And Governor Housing Prevent Possible Corrosion And Freezing Damage
1977/03/15
Service Tools For Low Emission Truck Engines With EGR
1977/06/29
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Changes To The Injection Pump And The Fuel Setting
1977/09/28
Correct Adjustment Of The Governor Control Linkage In Truck Engines Is Necessary To Prevent Low Power
1978/04/05
9N3700 Or 9N3299 Nozzle Assemblies Must Be Used On 3208 Engines That Are Equipped With Exhaust Gas Recirculation (EGR)
1978/04/05
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time
1978/07/05
Improved Guide Pin For Fuel Injection Pump Lifters
1978/08/30
New Control Cover Gives Better Control Of Exhaust Gas Recirculation System
1978/11/15
New Fuel Injection Nozzles Are Used In 3208 Truck Engines When Equipped With EGR
1978/11/15
A Washer With Closer Tolerances Is Now Used In The Governor And Fuel Pump Drive Group
1978/12/13
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation of Fuel Injection Pump and Governor Service Group{1286}
Installation of Fuel Injection Pump and Governor Service Group{1286}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N628 Bearing{7551, 1253}
Installation Of 8N628 Bearing{7551, 1253}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Installation Of 1W4793 Governor Spring (High Idle){1264, 1265}
Installation Of 1W4793 Governor Spring (High Idle){1264, 1265}
Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253}
Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Service Letter-NACD
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Fuel Injection Pump
3208 TRUCK ENGINE
Governor
3208 TRUCK ENGINE
Fuel Transfer Pump
3208 TRUCK ENGINE
Drive Gear For The Injection Pump
3208 TRUCK ENGINE
Automatic Timing Advance Unit<BR> (3&deg; and 5&deg; Units)
3208 TRUCK ENGINE
Automatic Timing Advance Unit<BR> 3&deg; For EGR Engine
3208 TRUCK ENGINE
AUTOMATIC TIMING ADVANCE UNIT<BR> 3&deg; FOR LOW EMISSION ENGINE
3208 TRUCK ENGINE
Service Letter-China
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Service Letter-Asia
Service Letter-APD
Disassembly and Assembly
Fuel Injection Pump Housing And Governor
3208 TRUCK ENGINE
Check Valve And Bypass Valve
3208 TRUCK ENGINE
Fuel Injection Pumps
3208 TRUCK ENGINE
Fuel Transfer Pump
3208 TRUCK ENGINE
Fuel Injection Pump Housing And Governor
3208 TRUCK ENGINE
Governor
3208 TRUCK ENGINE
Fuel Injection Pump Housing
3208 TRUCK ENGINE
Fuel Injection Pump Housing (With Thrust Washer)
3208 TRUCK ENGINE
Automatic Timing Advance
3208 TRUCK ENGINE
Service Magazine
Use The FT1525 Alignment Pin And FT1526 Fixture When Reconditioning Earlier 3208 Sleeve Metering Fuel Systems{0626,1264,1286}
1980/05/12
New Check Valve Used In Fuel Injection Pump Assembly{1251}
1980/05/26
New Governor Spring Available For Specific Engine Applications{1264,1265}
1981/02/23
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23
Fuel Pressure Relief Valve Is Shown Inverted (Wrong End Up) In Parts Book Illustrations {1253,1286}
1981/03/23
Check All Settings When Fuel Injection Pump Group Is Installed{1286,1264,1251,1253}
1981/03/30
Some Parts Books And Microfiche Show Wrong Governor And Fuel Pump Drive Groups For Specific Engines{1288,0374}
1981/06/29
Certification Film Necessary On Engines Adjusted For High Altitude Operation{7557,1251,1257,1264}
1981/08/10
FT1632 Bolt Used During Removal Of Sleeve From Sleeve Metering Fuel System{0621,1251,1253}
1981/08/31
Thrust Washer Used In Pump Housing For Sleeve Metering Fuel System{1253,1286}
1981/08/31
Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01
New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Modification Of 2P8315 Bracket Assembly{0652,1286}
1982/08/16
FT1698 Driver Can Be Used For Reconditioning Of Governor Housing{0626,0665,1264,1286}
1982/10/18
New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1983/12/05
Cross Link Between Fuel Racks Has Smoother Surface{1250,1257}
1985/03/11
Changes To Naturally Aspirated Truck Engines For 1985{1000,1200,1214,1218,1250,1251,1254}
1985/04/08
Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Drains In New Fuel Injection Pump Housing And Governor Housing Prevent Possible Corrosion And Freezing Damage{1286}
1977/03/07
Changes To The Injection Pump And The Fuel Setting{1251,1257}
1977/09/19
Use Correct Contact Point With Dial Indicator To Be Sure Of The Accuracy Of The Measurements Of Fuel Setting And Fuel Ratio Control Setting On Sleeve Metering Fuel Systems{0653,1250}
1977/09/26
Washer Removed From Variable Timing Unit{1206,1272}
1977/10/03
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Four More Remanufactured Fuel Pump And Governor Groups Available {1286}
1987/09/14
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps{1251,1254}
1987/11/23
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
Correct Adjustment Of The Governor Control Linkage In Truck Engines Is Necessary To Prevent Low Power{1265,1269}
1978/03/27
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Stronger Fuel Inlet Flanges Prevent Parts Damage And Keeps Air Out Of The Fuel System{1253}
1978/05/15
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time{1286,1256,1251}
1978/07/03
Improved Guide Pin For Fuel Injection Pump Lifters{1251}
1978/08/21
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
A Washer With Closer Tolerances Is Now Used In The Governor And Fuel Pump Drive Group{1288,7462}
1978/11/20
Check Valve Added To Keep Air From Entering Fuel System {1264}
1988/10/03
Improvements Made To Fuel Injection Pump And Governor Group{1253,1281,1286}
1979/03/05
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.{1253}
1979/05/07
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}
1979/08/27
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
Governor Springs For Sleeve Metering Fuel Systems {1264}
1990/05/21
Dowel Hole Removed From 8N3946 Governor Housing Improves Service Life{1287}
1991/07/08
New Spring Used In Governor Control Groups{1265}
1992/04/20

Caterpillar Parts SIS Catalog 3208 :

TORQUE CONTROL GP
6N-0509 TORQUE CONTROL GP
CONTROL GP-GOVERNOR
9L-6743 CONTROL GP-GOVERNOR
CONTROL GP
3T-5000 CONTROL GP
COVER GP
1W-7356 COVER GP
GOV & FUEL INJ PUMP GP
8N-5642 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
8N-5642 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
8N-5642 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
8N-5642 GOV & FUEL INJ PUMP GP
DRIVE GP-GOVERNOR & FUEL PUMP
9N-0740 DRIVE GP-GOVERNOR & FUEL PUMP
INJECTION GP-CETANE
9N-3771 INJECTION GP-CETANE
INJECTION GP-CETANE
9N-3771 INJECTION GP-CETANE
INJECTION GP-CETANE
9N-3771 INJECTION GP-CETANE
LINES GP-FUEL INJECTION
9N-3880 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9N-3880 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9N-3880 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
2W-0770 LINES GP-FUEL INJECTION

Truck sale:

 
11,500 
Caterpillar D3208EP, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY
CATERPILLAR 3208 1993
 
CATERPILLAR 3208 1993
- STATIONARY - DIESEL
WAGNER EQUIPMENT CO
United States
CATERPILLAR 3208 2004
 
CATERPILLAR 3208 2004
- STATIONARY GENERATOR SETS
EMPRESAS MATCO, S.A. DE C.V.
Sufragio Efectivo Norte 870 - Obregón -
1998 CAT 3208
USD $19,000 
1998 CAT 3208

Galactic Liquidation LLC
1990 CAT 3208
 
1990 CAT 3208

Ken Porter Auctions
Carson, California
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.