AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

8N7724 FUEL INJECTION PUMP GROUP-16 REQUIRED 3516 INDUSTRIAL ENGINE


FUEL SYSTEM
PUMP GP-FUEL INJECTION
LINES GP-FUEL
PUMP GP-FUEL INJECTION
PUMP GP-FUEL PRIMING
PUMP GP-FUEL TRANSFER
FILTER GP-FUEL

INDUSTRIAL ENGINE 3516 INDUSTRIAL ENGINE 27Z
 3516 INDUSTRIAL ENGINE 27Z00001-00649 SEBP1391 3516 27Z   (1982)

FUEL SYSTEM

PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
8N-7724 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7W-2062 PUMP GP-FUEL INJECTION
7C-9576 INJECTOR GP-FUEL
PUMP GP-FUEL INJECTION
2W-9579 PUMP GP-FUEL INJECTION
 

#SEBP13910620
 

8N-7724: PUMP GP-FUEL INJECTION

8N7724 FUEL INJECTION PUMP GROUP-16 REQUIRED
c350265 SEBP1391
8N7724 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7F-8698 [1] BOLT  
2. 7N-5487 [1] WASHER  
3. 8N-8069 [1] CLAMP-INJECTOR  
4. 2W-5200 CJ [1] NUT AS-INJECTION VALVE  
5. 7N-5325 J [1] CHECK-INJECTION VALVE  
6. 7N-5307 J [1] CAGE-INJ CHECK VALVE  
7. 5N-5321 J [1] GEAR-SPUR  
8. 7N-5312 J [1] CAGE-INJECTION SPRING  
9. 7N-5310 J [1] FOLLOWER-INJECTION  
10. 7N-5319 J [1] SEAT-INJ VALVE SPRING  
11. 7N-5314 J [1] DEFLECTOR-SPILL  
12. 7N-5317 J [1] SPRING-STOP PIN  
13. 7N-5318 J [1] RETAINER-PIN  
14. 7N-5322 J [1] RETAINER-INJ GEAR  
15. 7N-5315 J [1] SEAL-INJECTOR  
16. 7N-5308 J [1] BODY AS-INJECTOR  
17. 7N-5309 J [1] RACK AS-INJECTOR  
18. 7N-5313 J [1] GEAR (23 TEETH)  
19. 7N-5320 J [1] PIN-INJECTION STOP  
20. 7N-5324 J [1] SPRING-PLUNGER  
21. 6V-1250 [1] SEAL-O-RING  
22. 8J-8725 C [2] SEAL-O-RING  
23. 8N-9944 [1] PLUG  
24. 2W-7444 CAV [1] PLUNGER & BUSHING AS  
    (MARKED L )
    -OR-
  2W-7445 CAV [1] PLUNGER & BUSHING AS  
    (MARKED M)
    -OR-
  2W-7446 CAV [1] PLUNGER & BUSHING AS  
    (MARKED H )
25. 2W-7447 CAV [1] TIP AS (MARKED L )  
    -OR-
  2W-7448 CAV [1] TIP AS (MARKED M)  
    -OR-
  2W-7449 CAV [1] TIP AS (MARKED H )  
    THE FOLLOWING REPAIR
    KIT IS AVAILABLE
  1W-7668 [1] KIT-INJECTOR (INJECTOR REPAIR)  
    (PROVIDES BOTH TIP AS.
    & PLUNGER AS. FOR
    UNITS NOT MARKED
    L,M OR H)
  A   NOT PART OF THIS GROUP
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP13910621
 

7W-2062: PUMP GP-FUEL INJECTION

7W2062 PUMP GROUP-ENGINE FUEL INJECTION
SERIAL NO. 27Z650-UP.
FOR FIELD REPLACEMENT OF 7W2269 FUEL INJECTOR AS ORDER 7C9576
FUEL INJECTOR GP-PAGE 239.02
c603650 SEBP1391
7W2062 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4F-7226 [1] BOLT  
2. 7N-5487 [1] WASHER  
3. 1N-4910 [1] CLAMP-INJECTOR  
4. 7W-2269 R [1] INJECTOR AS-FUEL  
  2W-5200 [1] NUT AS-INJECTION VALVE  
5. 7N-5325 [1] CHECK-INJECTION VALVE  
6. 7N-5307 [1] CAGE-INJ CHECK VALVE  
7. 7N-5321 [1] SPRING-FUEL VALVE  
8. 7N-5312 [1] CAGE-INJECTION SPRING  
9. 7W-2237 [1] FOLLOWER  
10. 7N-5319 [1] SEAT-INJ VALVE SPRING  
11. 7N-5314 [1] DEFLECTOR-SPILL  
12. 7N-5317 [1] SPRING-STOP PIN  
13. 7N-5318 [1] RETAINER-PIN  
14. 7N-5322 [1] RETAINER-INJ GEAR  
15. 7N-5315 [1] SEAL-INJECTOR  
16. 7W-2236 [1] BODY AS  
17. 7N-5309 [1] RACK AS-INJECTOR  
18. 7N-5313 [1] GEAR (23 TEETH)  
19. 7N-5320 [1] PIN-INJECTION STOP  
20. 7W-0296 [1] SPRING-INJECTOR  
21. 7W-1034 [1] PLUNGER AS  
22. 7W-2189 [1] TIP AS  
23. 6V-1250 [1] SEAL-O-RING  
24. 8J-8725 [2] SEAL-O-RING  
25. 8N-9944 [1] PLUG  
  R   REMFG PART MAY BE AVAILABLE
 

#SEBP13910622
 

7C-9576: INJECTOR GP-FUEL

7C9576 INJECTOR GP-FUEL*R
FIELD REPLACEMENT FOR 7W2269 FUEL INJECTOR AS-PAGE 239.01
SEBP13910622 SEBP1391
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
  7C-9795 [1] CONE-NOSE  
  7C-0344 [1] NOZZLE AS-UNIT INJECTOR  
  6V-9178 [1] SEAL-O RING  
 

#SEBP13910623
 

2W-9579: PUMP GP-FUEL INJECTION

2W9579 PUMP GP-FUEL INJECTION
c351116 SEBP1391
2W9579 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7C-0345 CR [1] INJECTOR GP-FUEL  
2. 1N-4910 [1] CLAMP-INJECTOR  
3. 4F-7226 [1] BOLT  
4. 7N-5487 [1] WASHER  
5. 8N-9944 [1] PLUG  
6. 8J-8725 [2] SEAL-O-RING  
7. 6V-1250 [1] SEAL-O-RING  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMFG PART MAY BE AVAILABLE
 

#SEBP13910624
 

7N-8599: PUMP GP-FUEL PRIMING

7N8599 FUEL PRIMING PUMP GROUP
PART OF 8N9853 FUEL PRIMING PUMP GROUP SHOWN ON PAGE 240
c301867 SEBP1391
7N8599 PUMP GP-FUEL PRIMING Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1W-8396 C [1] PUMP ASSEM.  
2. 7B-2742 [1] BOLT  
3. 5P-0537 [1] WASHER  
4. 1P-0436 [1] GASKET  
5. 9M-1974 [1] WASHER  
6. 1B-7182 [1] BOLT  
    THE FOLLOWING REPAIR KIT IS AVAILABLE:
    (Includes knobs, pin, cover, spring & washers)
  C   INDICATES CHANGE
 

#SEBP13910625
 

8N-9853: PUMP GP-FUEL PRIMING

8N9853 FUEL PRIMING PUMP GROUP
7N8599 PUMP PARTS ARE SHOWN ON PAGE 240
c300360 SEBP1391
8N9853 PUMP GP-FUEL PRIMING Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7N-8599 CY [1] PUMP GROUP  
    (Separate Illustration)
2. 2H-9523 [1] GROMMET  
3. 8N-3480 [1] CLIP  
  Y   SEPARATE ILLUSTRATION
 

#SEBP13910626
 

1N-4478: PUMP GP-FUEL TRANSFER

1N4478 FUEL TRANSFER PUMP GROUP
PART OF 8N6151 FUEL TRANSFER PUMP GROUP SHOWN ON PAGE 242
c601344 SEBP1391
1N4478 PUMP GP-FUEL TRANSFER Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8F-8178 [1] BOLT  
2. 1W-4008 [1] GASKET  
3. 1W-4010 [1] PLATE AS  
  7C-2870 C [2] BUSHING-TERMINAL  
4. 6V-0895 [2] SEAL-O-RING  
5. 1W-4006 [1] CASING  
6. 1W-6935 [2] SLEEVE  
7. 112-3597 [1] SEAL-LIP  
8. 112-3596 [1] SEAL-LIP  
9. 124-9437 [1] SHAFT AS-DRIVE  
10. 1W-4121 [1] BRACKET AS  
  7C-2870 C [2] BUSHING-TERMINAL  
11. 1W-6936 [1] CAP-RELIEF VALVE  
12. 7W-3556 C [1] WASHER  
13. 1W-4655 [1] SPRING-VALVE  
14. 1W-4007 [1] POPPET-VALVE  
15. 1W-4003 [1] GEAR AS-IDLER  
16. 8S-4710 [1] BOLT  
17. 1W-4005 [1] HEAD AS  
18. 1W-4009 [1] VALVE AS  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP13910627
 

8N-6151: PUMP GP-FUEL TRANSFER

8N6151 FUEL TRANSFER PUMP GROUP
1N4478 PUMP PARTS ARE SHOWN ON PAGE 241
c413263 SEBP1391
8N6151 PUMP GP-FUEL TRANSFER Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1N-4636 [1] COUPLING-DRIVE  
2. 313-7770 CYR [1] PUMP GP-FUEL TRANSFER (1-SECTION GEAR)  
3. 1H-9696 [1] SEAL-O-RING  
4. 5L-1761 C [4] BOLT (5/16-18X5.5-IN)  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMFG PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP13910628
 

8N-7726: FILTER GP-FUEL

8N7726 FUEL FILTER GROUP
SERIAL NO. 27Z1 TO 27Z634 INCLUSIVE
c312978 SEBP1391
8N7726 FILTER GP-FUEL Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 0S-1588 [12] BOLT  
2. 5M-2894 [14] WASHER  
3. 4J-4382 [1] PLUG-PIPE  
4. 1W-2884 [1] HOUSING AS-FUEL FLTR  
5. 9S-4190 [1] PLUG-0-RING  
  2M-9780 [1] SEAL-O-RING  
6. 9S-4182 C [3] PLUG  
  3J-7354 [3] SEAL-O-RING  
7. 2W-6288 [1] COVER-FILTER HOUSING  
8. 4M-0189 [2] SEAL-O-RING  
9. 2S-5100 [1] VALVE AS-NEEDLE  
10. 9S-4182 C [1] PLUG  
  3J-7354 [1] SEAL-O-RING  
11. 0L-1351 [2] BOLT  
12. 001-5600 C [1] RING-SNAP  
13. 8N-9850 C [5] ELEMENT AS-FUEL FILTER  
14. 1N-2896 [1] RETAINER-SPRING  
15. 3P-1156 [1] SEAL-O-RING  
16. 1W-3298 [1] COVER-FILTER HOUSING  
17. 1N-2895 [1] SPRING  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP13910629
 

8N-7726: FILTER GP-FUEL

8N7726 FUEL FILTER GROUP
SERIAL NO. 27Z635 TO 27Z648 INCLUSIVE
c327886 SEBP1391
8N7726 FILTER GP-FUEL Parts scheme
  For full view, you need register

Parts for your 3516 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 0S-1588 [12] BOLT  
2. 5M-2894 [14] WASHER  
3. 4J-4382 [1] PLUG-PIPE  
4. 4W-8918 C [1] HOUSING AS-FUEL  
5. 9S-4190 [1] PLUG-0-RING  
  2M-9780 [1] SEAL-O-RING  
6. 9S-4191 C [1] PLUG-O-RING  
  6V-5049 C [1] SEAL-O-RING  
7. 2W-6288 [1] COVER-FILTER HOUSING  
8. 4M-0189 [2] SEAL-O-RING  
9. 2S-5100 [1] VALVE AS-NEEDLE  
10. 9S-4182 C [5] PLUG  
  3J-7354 C [5] SEAL-O-RING  
11. 0L-1351 [2] BOLT  
12. 001-5600 [1] RING-SNAP  
13. 8N-9850 [5] ELEMENT AS-FUEL FILTER  
14. 1N-2896 [1] RETAINER-SPRING  
15. 3P-1156 [1] SEAL-O-RING  
16. 1W-3298 [1] COVER-FILTER HOUSING  
17. 1N-2895 [1] SPRING  
18. 4B-9782 C [1] BALL  
  9N-1752 C [1] SPRING  
  C   CHANGE FROM PREVIOUS TYPE
 

Information:

Engine News
Use 6V4172 Injector Sleeve When You Clean Fuel Injectors
1981/07/15
Explanation Of Differences In Timing Advance Information
1981/08/26
Bulged Capsule-Type Fuel Nozzles
1982/10/20
Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
Disconnect Fuel Lines And Install Caps Before Unit Injectors Are Removed
1983/02/16
Bolt Used Instead Of Stud In Governor Fastener Group To Prevent Damage To Governor Housing
1984/04/11
Quadrants Improved In Governor Control Groups
1984/07/11
Additional Information For Correct Fuel Injector Timing
1984/12/12
Improved Valve Mechanism Cover Group Has A New Valve Cover And Seal
1985/01/16
Low Oil Level In Governor Can Cause Erratic Engine RPM
1985/02/01
Tighten Bolts To Correct Torque In 3161 Governor
1985/02/01
Valve Mechanism Groups Use New Lifter Assemblies
1985/08/01
Repair Kits Available For Air Actuator Used In Governor Control Groups
1985/09/01
Engine Valve Lash And Fuel Injection Timing Adjustment Procedure
1985/09/01
A Water Separator Can Help Prevent Fuel Injector Damage If Fuel Is Contaminated With Water
1986/01/01
Lubricate Clamp When Installing Unit Injector Assemblies
1986/01/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
How To Adjust Arming Pressure On Fuel Ratio Control On Caterpillar 3161 Governor
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
Improvements For Caterpillar 3161 Governors
1986/07/01
Fuel Injector Reference For 3500 Family Engines
1987/01/01
Fuel Ratio Control Diaphragms On 3161 Governors
1987/02/01
Improved Fuel Transfer Pump Cover; Weep Hole Moved
1987/03/01
Checking Injector Synchronization On Engines Equipped With New 11.0 mm Injectors
1987/04/01
New Washer Used In Fuel Transfer Pump Group
1987/04/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Features And Servicing Of The Various Caterpillar 3161 Governors
1987/06/01
Fuel Injector Trim Bolt
1987/06/01
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps
1987/12/01
Additional Information For Installing Fuel Injectors
1988/06/01
Two 11 mm Injectors Available For Parts Service
1988/07/01
Replacement Fuel Injector Nozzles With New Nose Cones Available
1988/08/01
One-Piece Tappet (Follower) Used In 11 mm (Type 2) Fuel Injectors
1988/12/01
Check Valve Added To Fuel Injection Lines
1989/05/01
New Connector With An Orifice Added To Fuel Injection Lines Groups To Help Prevent Cavitation
1989/07/01
Improved Control Rod Assembly Used In Fuel Injection Control Groups
1989/08/01
New Fuel Injectors Available For Parts Service
1989/09/01
New Fuel Injector Assemblies Used
1989/10/01
Fuel Injector Reference For 3500 Family of Engines
1989/10/01
New 7C9580 Fuel Injector (Type 2) Available To Replace 2W5201 Fuel Injector (Type 1)
1990/06/01
Some Fuel Injectors May Be Used In Mixed Sets
1990/06/01
If Trim Screw On Unit Injector Is Loose, Injector Must Be Replaced
1990/09/01
New "On Engine" Adjustment Procedure For 3161 Woodward Governor
1990/10/01
Remanufactured Type 1 Fuel Injector Assembly Available For 3500 Family Of Engines Equipped With UG8 Governors
1991/04/01
Fuel Injection Pump Bushing Torque Increased
1991/04/01
Corrections For Systems Operation, Troubleshooting, And Specifications For 2301 Electric Governors For Generator Set And Industrial Engines, SENR2928-01
1991/05/01
New Speed Setting Clutch Group For 3161 Woodward Governors
1991/06/01
New Return Spring Used In Unit Injectors
1991/08/01
End Clearance Specification Changed For Front Shaft In Fuel Injection Control
1991/10/01
New And Remanufactured Fuel Injector Reference
1992/05/01
New And Remanufactured Fuel Injector Reference
1993/01/01
New Fuel Injector Group Help Reduce Plunger And Barrel Seizures
1993/05/01
New 3161 Governor With Improved Fuel Limiter
1993/09/01
Fuel Dilution In The Engine Oil{1290,1318}
1994/05/01
New Seals Extend Life of Fuel Transfer Pump{1256}
1994/11/01
Be Sure The Cylinder Head Bore For the Unit Injector Is Clean When the Unit Injector Is Replaced {1290}
1999/07/01
Tightening Torque Increased For Nuts In Fuel Injector Wiring Harness Cap Assembly{1408}
1999/09/01
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Troubleshooting Engines with Mechanical Unit Injection (MUI) {1000, 1254}
2006/01/02
Do not Use the 1U-6661 Pop Tester Gp to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/24
Do not Use the 1U-6661 Pop Tester Gp to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/24
Do not Use the 1U-6661 Pop Tester Gp or the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
New Sequence for Adjusting the Fuel Injectors in 3516, 3516B, and 3516C Engines {1290}
2012/12/21
Operation and Maintenance Manual
Fuel Injector - Inspect/Adjust
3500 Industrial and Generator Set Engines
Special Instruction
Installation of 2W8511 Cam Loading Spring{1264}
Installation of 2W8511 Cam Loading Spring{1264}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation of Service Replacement Woodward Governor Group{1264}
Installation of Service Replacement Woodward Governor Group{1264}
Nozzle Assembly Replacement for Type 2 Fuel Injectors{1254}
Nozzle Assembly Replacement for Type 2 Fuel Injectors{1254}
Installation and Adjustment of 3161 Governor on 3500 Family of Engines{1264}
Installation and Adjustment of 3161 Governor on 3500 Family of Engines{1264}
Spring Replacement for Type 2 Fuel Injectors{1250}
Spring Replacement for Type 2 Fuel Injectors{1250}
3500 Electronic Unit Injection (EUI) Fuel Priming Procedure{1250, 1258}
3500 Electronic Unit Injection (EUI) Fuel Priming Procedure{1250, 1258}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N6414 Ether Starting Aid Group{1456}
Installation Of 8N6414 Ether Starting Aid Group{1456}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Performing a Multiple Cylinder Cutout Test {1290}
Performing a Multiple Cylinder Cutout Test {1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290}
Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Service Letter-NACD
Remove Certain 0R0906, 0R1756, 0R1758, 0R2921, 0R2922, 0R2923, 0R2924, 0R2925, 0R3051, And 0R3052 Remanufactured Unit Injectors Used On 3500 Engines From Parts Stock
Remove Certain 0R0906, 0R1756, 0R1758, 0R2921, 0R2922, 0R2923, 0R2924, 0R2925, 0R3051, And 0R3052 Remanufactured Unit Injectors Used On 3500 Engines From Parts Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Fuel Injector Mechanism
3500 Industrial Engines
Fuel Injector Mechanism
3500 Industrial Engines
Fuel Injector
3500 Industrial Engines
Fuel Injector Mechanism
3500 Industrial Engines
Service Letter-China
Remove Certain 0R0906, 0R1756, 0R1758, 0R2921, 0R2922, 0R2923, 0R2924, 0R2925, 0R3051, And 0R3052 Remanufactured Unit Injectors Used On 3500 Engines From Parts Stock
Remove Certain 0R0906, 0R1756, 0R1758, 0R2921, 0R2922, 0R2923, 0R2924, 0R2925, 0R3051, And 0R3052 Remanufactured Unit Injectors Used On 3500 Engines From Parts Stock
Service Letter-Asia
Systems Operation
Fuel Injector
3500 Industrial Engines
Fuel Injection Cycle
3500 Industrial Engines
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Service Letter-APD
Remove Certain 0R0906, 0R1756, 0R1758, 0R2921, 0R2922, 0R2923, 0R2924, 0R2925, 0R3051, And 0R3052 Remanufactured Unit Injectors Used On 3500 Engines From Parts Stock
Remove Certain 0R0906, 0R1756, 0R1758, 0R2921, 0R2922, 0R2923, 0R2924, 0R2925, 0R3051, And 0R3052 Remanufactured Unit Injectors Used On 3500 Engines From Parts Stock
Testing and Adjusting
Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
3500 Industrial Engines
Fuel Injector Timing
3500 Industrial Engines
Fuel Injector Synchronization
3500 Industrial Engines
Checking Engine Cylinders
3500 Industrial Engines
Disassembly and Assembly
GOVERNOR
3500 INDUSTRIAL ENGINE
GOVERNOR DRIVE
3500 INDUSTRIAL ENGINE
FUEL INJECTORS
3500 INDUSTRIAL ENGINE
Service Magazine
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Disconnect Fuel Lines And Install Caps Before Unit Injectors Are Removed{1274,1254,1251}
1983/01/17
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Crankshaft Positions For Injector Timing And Valve Clearance Settings{0374,1104,1290}
1983/11/21
Bolt Used Instead Of Stud In Governor Fastener Group To Prevent Damage To Governor Housing {1264,1287}
1984/04/02
Quadrants Improved In Governor Control Groups{1265,1264}
1984/05/21
Additional Information For Correct Fuel Injector Timing{1290}
1984/11/19
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Tighten Bolts To Correct Torque In 3161 Governor{1264}
1985/02/04
Rough Handling Can Move Droop Lever Out Of Position{1264}
1985/08/05
Adjusting Pneumatic Speed Control For Correct Operation{1264}
1985/09/02
Engine Valve Lash And Fuel Injection Timing Adjustment Procedure {1100,1251}
1985/09/16
List Of Mechanical Service Meters For Earlier 3500 Series Engines Using Mechanical Service Meters{1286}
1985/09/23
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
A Water Separator Can Help Prevent Fuel Injector Damage If Fuel Is Contaminated With Water{1263,1250,1273}
1985/12/09
Lubricate Clamp When Installing Unit Injector Assemblies{1290}
1986/01/13
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Improvements For Caterpillar 3161 Governors{1264}
1986/06/16
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Fuel Injector Reference For 3500 Family Engines{1290}
1987/01/19
Improved Injector Clamp Eliminates Interference With Bridge {1290}
1987/03/09
Improved Fuel Transfer Pump Cover; Weep Hole Moved{1255}
1987/03/23
New Washer Used In Fuel Transfer Pump Group {1256}
1987/03/30
Checking Injector Synchronization On Engines Equipped With New 11.0 mm Injectors{1290}
1987/04/13
Fuel Injection Timing Adjustment{1250}
1987/04/20
Fuel Injector Trim Bolt {1257}
1987/06/01
Features And Servicing Of The Various Caterpillar 3161 Governors {1264,1278}
1987/06/01
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps{1251,1254}
1987/11/23
Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
Additional Information For Installing Fuel Injectors{1290,1257}
1988/06/13
Two 11 mm Injectors Available For Parts Service{1250,1290}
1988/06/20
Replacement Fuel Injector Nozzles With New Nose Cones Available{0706,1254,1290}
1988/07/25
New Rocker Arm Shaft Assembly and Bolts Used{1102}
1988/09/05
Check Valve Added To Keep Air From Entering Fuel System {1264}
1988/10/03
Digital Dial Indicator Simplifies Fuel Injection Timing Adjustment{0782,0760,1257,1290}
1988/11/07
One-Piece Tappet (Follower) Used In 11 mm (Type 2) Fuel Injectors{1290}
1988/11/21
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Check Valve Added To Fuel Injection Lines {1274}
1989/05/22
New Connector With An Orifice Added To Fuel Injection Lines Groups To Help Prevent Cavitation{1274}
1989/06/26
Improved Control Rod Assembly Used In Fuel Injection Control Groups{1298}
1989/07/24
New Fuel Injectors Available For Parts Service{1290}
1989/08/28
Fuel Injector Reference For 3500 Family Of Engines{1290}
1989/10/02
New Fuel Injector Assemblies Used{1290}
1989/10/16
Some Fuel Injectors May Be Used In Mixed Sets {1290}
1990/05/21
New 7C9580 Fuel Injector (Type 2) Available To Replace 2W5201 Fuel Injector (Type 1) {1290}
1990/06/11
New "On Engine" Adjustment Procedure For 3161 Woodward Governor {1264,0782}
1990/10/22
Field Replacement Of Spacer To Correct Possible Sticking In Woodward 3161 Governor Electric Shutoff Group{1264}
1990/11/19
Fuel Injection Pump Bushing Torque Increased {1253}
1991/04/01
Remanufactured Type 1 Fuel Injector Assembly Available For 3500 Family Of Engines Equipped With UG8 Governors {1254,1264}
1991/04/01
New Speed Setting Clutch Group For 3161 Woodward Governors{1265}
1991/05/20
New Return Spring Used In Unit Injectors {1290}
1991/07/22
End Clearance Specification Changed For Front Shaft In Fuel Injection Control{1251,1258}
1991/10/14
New And Remanufactured Fuel Injector Reference{1290}
1992/05/18
Modifying Former 2W8888 Rocker Arm Shaft For Use With New 8T7581 Rocker Arm Shaft Bolt{1102}
1992/12/21
New And Remanufactured Fuel Injector Reference {1290}
1993/01/18
New Fuel Injector Group Help Reduce Plunger And Barrel Seizures{1290}
1993/05/31
New 3161 Governor With Improved Fuel Limiter{1264}
1993/09/20
Fuel Dilution In The Engine Oil{1290,1318}
1994/05/16
Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14

Caterpillar Parts SIS Catalog 3516 :

TORQUE CONTROL GP
4W-0986 TORQUE CONTROL GP
TORQUE CONTROL GP
4W-0991 TORQUE CONTROL GP
TORQUE CONTROL GP
4W-0995 TORQUE CONTROL GP
TORQUE CONTROL GP
2W-1483 TORQUE CONTROL GP
LINKAGE GP-GOVERNOR
2W-1484 LINKAGE GP-GOVERNOR
CONTROL GP-GOVERNOR
2W-1459 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
2W-2643 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
4N-3829 CONTROL GP-GOVERNOR
PUMP GP-FUEL INJECTION
7W-2062 PUMP GP-FUEL INJECTION
7C-9576 INJECTOR GP-FUEL
PUMP GP-FUEL INJECTION
2W-9579 PUMP GP-FUEL INJECTION
PUMP GP-FUEL PRIMING
7N-8599 PUMP GP-FUEL PRIMING
PUMP GP-FUEL PRIMING
8N-9853 PUMP GP-FUEL PRIMING
PUMP GP-FUEL TRANSFER
1N-4478 PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
8N-6151 PUMP GP-FUEL TRANSFER
FILTER GP-FUEL
8N-7726 FILTER GP-FUEL

Truck sale:

 
719,892 
Caterpillar 3516, Stationary Generator Sets, Construction
- Stationary Generator Sets
TOROMONT POWER SYSTEMS
Caterpillar 3516, mobile generator sets, Construction
298,989 
Caterpillar 3516, mobile generator sets, Construction
- mobile generator sets
FINANZAUTO S.A.
Caterpillar PM3516, mobile generator sets, Construction
500,000 
Caterpillar PM3516, mobile generator sets, Construction
- mobile generator sets
FOLEY EQUIPMENT COMPANY
Caterpillar PM3516, mobile generator sets, Construction
500,000 
Caterpillar PM3516, mobile generator sets, Construction
- mobile generator sets
FOLEY EQUIPMENT COMPANY
Caterpillar 3516, Stationary Generator Sets, Construction
800,000 
Caterpillar 3516, Stationary Generator Sets, Construction
- Stationary Generator Sets
MACALLISTER MACHINERY CO., INC
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.