3406B GENERATOR SET ENGINE 2WB00001-11475 FUEL SYSTEM Caterpillar SIS

GEN SET ENGINE 3406B GEN SET ENGINE 2WB
3406B GENERATOR SET ENGINE 2WB00001-11475 SEBP1436 3406B 2WB (1983)

Parts group 3406B:

For full view, you need register

FUEL SYSTEM

CONTROL GP-GOVERNOR

7W-1455 ACTUATOR AS-GOVERNOR

7W1455 WOODWARD ACTUATOR ASSEMBLY-EG3P
AN ATTACHMENT

7E-0123 MOUNTING GP-GOVERNOR ACTUATOR

7E0123 MOUNTING GP-ACTUATOR
AN ATTACHMENT

7W-1454 ACTUATOR AS-GOVERNOR

7W1454 WOODWARD ACTUATOR ASSEMBLY-EG3P
AN ATTACHMENT

DRAIN GP-FUEL

4W-0423 DRAIN GP-FUEL

4W423 DRAIN GP-FUEL
TYPE 1-LINES & ALARM SWITCH
FOR USE WITH DOUBLE WALLED INJECTION LINES
AN ATTACHMENT

4W-0423 DRAIN GP-FUEL

4W0423 DRAIN GP-FUEL
TYPE 2-LINES & ALARM SWITCH
FOR USE WITH DOUBLE WALLED FUEL INJECTION LINES
AN ATTACHMENT

7E-3039 DRAIN GP-FUEL

7E3039 DRAIN GP-FUEL
S/N 2WB6495-UP. LINES & ALARM SWITCH
FOR USE WITH DOUBLE WALLED INJECTION LINES
AN ATTACHMENT

DRIVE GP-TACHOMETER

4W-1101 DRIVE GP-TACHOMETER

4W1101 DRIVE GP-TACHOMETER-DUAL
NOT FOR USE WITH ANY WOODWARD GOVERNOR
AN ATTACHMENT

1W-8235 DRIVE GP-TACHOMETER

1W8235 DRIVE GP-TACHOMETER-SINGLE
NOT FOR USE WITH WOODWARD GOVERNOR
AN ATTACHMENT

FILTER GP-FUEL

5N-0378 FILTER GP-PRIMARY FUEL

5N0378 FILTER GP-PRIMARY FUEL
FOR USE WITH BATTERY RACK & BATTERY
8H7204-PAGE 141
AN ATTACHMENT

4N-1981 FILTER GP-FUEL

4N1981 FILTER GP-FUEL

8H-7204 FILTER GP-FUEL

8H7204 FILTER GP-PRIMARY FUEL
PART OF 5N0378 FILTER
FOR USE WITH 6N3212 PRIMARY FUEL FILTER MOUNTING
AN ATTACHMENT

GOVERNOR GP

1W-1182 FASTENER GP-WOODWARD GOVERNOR

1W1182 FASTENER GP-GOVERNOR-WOODWARD

1W-1179 FASTENER GP-WOODWARD GOVERNOR

1W1179 FASTENER GP-GOVERNOR-WOODWARD
TYPE 1. ALSO PART OF 4W8196 CONVERSION
AN ATTACHMENT
NOTE: 7W6652 ACTUATOR AS IS AVAILABLE

1W-1179 FASTENER GP-WOODWARD GOVERNOR

1W1179 FASTENER GP-GOVERNOR-WOODWARD
TYPE 2. ALSO PART OF 4W8196 CONVERSION
AN ATTACHMENT
NOTE: 7W6652 ACTUATOR AS IS AVAILABLE

1W-1183 GOVERNOR GP

1W1183 GOVERNOR GROUP
S/N 2WB1-582
2W1842-PAGE 157

1W-1183 GOVERNOR GP

1W1183 GOVERNOR GP
S/N 2WB6154-10017
9Y1215-PAGE 157.03

1W-1183 GOVERNOR GP

1W1183 GOVERNOR GP
S/N 2WB583-6153
4W6814-PAGE 157.01

1W-1183 GOVERNOR GP

1W1183 GOVERNOR GP
S/N 2WB10018-UP
4P8242-PAGE 157.05

4W-8196 CONVERSION GP-GOVERNOR

4W8196 CONVERSION GP-GOVERNOR
WOODWARD EG3P
FIELD INSTALLATION

2W-1842 GOVERNOR GP

2W1842 GOVERNOR GROUP
S/N 2WB1-582
2W1843-PAGE 157.02
PART OF 1W1183 GOVERNOR

4W-6814 GOVERNOR GP

4W6814 GOVERNOR GP-WOODWARD
S/N 2WB583-3210
PART OF 1W1183 GOVERNOR

2W-1843 COVER GP-GOVERNOR

2W1843 MOTOR COVER ASSEMBLY
S/N 2WB1-582
PART OF 2W1842 GOVERNOR

4W-6814 GOVERNOR GP

4W6814 GOVERNOR GP-WOODWARD
S/N 2WB3211-6153
PART OF 1W1183 GOVERNOR

9Y-1215 GOVERNOR GP

9Y1215 GOVERNOR GP-WOODWARD
S/N 2WB6154-10017
PART OF 1W1183 GOVERNOR

4P-8242 GOVERNOR GP

4P8242 GOVERNOR GP-WOODWARD
S/N 2WB10018-UP
PART OF 1W1183 GOVERNOR

7W-1455 ACTUATOR AS-GOVERNOR

7W1455 WOODWARD ACTUATOR ASSEMBLY-EG3P
AN ATTACHMENT

1W-6378 DRIVE GP-GOVERNOR & FUEL PUMP

1W6378 GOVERNOR & FUEL PUMP DRIVE GROUP - TYPE 1

1W-6378 DRIVE GP-GOVERNOR & FUEL PUMP

1W6378 GOVERNOR & FUEL PUMP DRIVE GROUP - TYPE 2

7E-7269 DRIVE GP-GOVERNOR & FUEL PUMP

7E7269 DRIVE GP-GOVERNOR & FUEL PUMP

4P-1365 DRIVE GP-GOVERNOR & FUEL PUMP

4P1365 DRIVE GP-GOVERNOR & FUEL PUMP

7E-0123 MOUNTING GP-GOVERNOR ACTUATOR

7E0123 MOUNTING GP-ACTUATOR
AN ATTACHMENT

7W-1454 ACTUATOR AS-GOVERNOR

7W1454 WOODWARD ACTUATOR ASSEMBLY-EG3P
AN ATTACHMENT

7W-0043 PUMP GP-GOV & FUEL INJ

7W0043 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
26 DEG. TIMING. S/N 2WB1031-6494
1W1205-PAGE 160, 4W2547-PAGE 164

7W-0043 PUMP GP-GOV & FUEL INJ

7W0043 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
26 DEG. TIMING. S/N 2WB6495-9233
1W1205-PAGE 160, 4W2547-PAGE 164

7W-0043 PUMP GP-GOV & FUEL INJ

7W0043 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
26 DEG. TIMING. S/N 2WB9234-UP
1W1205-PAGE 160, 4P1383-PAGE 164.04

2W-8030 PUMP GP-GOV DRIVE & FUEL INJ

2W8030 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB1-7564
1W1205-PAGE 160 & 2W6972-PAGE 163

2W-8030 PUMP GP-GOV DRIVE & FUEL INJ

2W8030 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB7565-9233
1W1205-PAGE 160, 7E7267-PAGE 163.01

2W-8030 PUMP GP-GOV DRIVE & FUEL INJ

2W8030 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB9234-UP
1W1205-PAGE 160, 4P1385-PAGE 164.04.01

7W-9008 PUMP GP-GOV DRIVE & FUEL INJ

7W9008 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB3244-9233
1W1205-PAGE 160, 4W2549-PAGE 164.02

7W-9008 PUMP GP-GOV DRIVE & FUEL INJ

7W9008 PUMP GP-GOVERNOR DRIVE
S/N 2WB9234-UP
1W1205-PAGE 160, 4P1381-PAGE 164.03

1W-1205 DRIVE GP-GOVERNOR

1W1205 DRIVE GP-GOVERNOR-WOODWARD-PART 1 OF 2
1W1204-PAGE 162
PART OF 2W8030 & 7W0043 PUMP, 4W8196 CONVERSION, & 7W9008 GOVERNOR

1W-1205 DRIVE GP-GOVERNOR

1W1205 DRIVE GP-GOVERNOR-WOODWARD-PART 2 OF 2
PART OF 2W8030 & 7W0043 PUMP, 4W8196 CONVERSION, & 7W9008 GOVERNOR

1W-1204 HOUSING AS-GOVERNOR DRIVE

1W1204 HOUSING AS-GOVERNOR DRIVE
PART OF 1W1205 DRIVE-GOVERNOR

7E-0257 PUMP GP-GOV & FUEL INJ

7E0257 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB11415-UP
2W6660-PAGE 167.01, 9Y1234-PAGE 153
2W8576-PAGE 168, 4P1381-PAGE 164.03

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 PUMP GP-GOVERNOR & FUEL INJECTION
TYPE 1. S/N 2WB1-6141
2W6972-PAGE 163, 2W6312-PAGE 167 & 2W8576-PAGE 168

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 PUMP GP-GOVERNOR & FUEL INJECTION
TYPE 2. S/N 2WB1-6141
2W6972-PAGE 163, 2W8576-PAGE 168 & 2W6660-PAGE 167.01

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6142-7564
2W6972-PAGE 163, 2W8576-PAGE 168, 2W6660-PAGE 167.01 &
9Y1234-PAGE 153

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB7565-8181
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 7E7267-PAGE 163.01

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB8182-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 4P1385-PAGE 164.04.01

4P-0667 PUMP GP-GOV & FUEL INJ

4P0667 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB8192-9233
2W6660-PAGE 167.01, 9Y1234-PAGE 153
2W8576-PAGE 169B, 7E7267-PAGE 163.01

4P-0667 PUMP GP-GOV & FUEL INJ

4P0667 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W6660-PAGE 167.01, 9Y1234-PAGE 153
2W8576-PAGE 169B, 4P1385-PAGE 164.04.01

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 PUMP GP-GOVERNOR & FUEL INJECTION
S/N 2WB1-2975
2W6972-PAGE 163, 2W6312-PAGE 167, 2W8576-PAGE 168

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 PUMP GP-GOVERNOR & FUEL INJECTION
S/N 2WB2976-6141
2W6972-PAGE 163, 2W6660-PAGE 167.01, 2W8576-PAGE 168

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6142-7564
2W6972-PAGE 163, 2W8576-PAGE 168 & 9Y1234-PAGE 153
2W6660-PAGE 167.01

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB7565-9233
2W6660-PAGE 167.01, 2W8576-PAGE 168
9Y1234-PAGE 153, 7E7267-PAGE 163.01

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W6660-PAGE 167.01, 2W8576-PAGE 168, 9Y1234-PAGE 153
4P1385-PAGE 164.04.01

7W-0066 PUMP GP-GOV & FUEL INJ

7W0066 GOVERNOR & FUEL INJECTION PUMP GP
TYPE 1. S/N 2WB1031-9233
4W2547-PAGE 164, 2W6312-PAGE 167 & 2W8576-PAGE 168

7W-0066 PUMP GP-GOV & FUEL INJ

7W0066 GOVERNOR & FUEL INJECTION PUMP GP
TYPE 2. S/N 2WB1031-9233
9Y1234-PAGE 153, 4W2547-PAGE 164, 2W6660-PAGE 167.01 & 2W8576-PAGE 168

7W-0066 PUMP GP-GOV & FUEL INJ

7W0066 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 4P1383-PAGE 164.04

7W-0067 PUMP GP-GOV & FUEL INJ

7W0067 PUMP GP-GOVERNOR & FUEL INJECTION
S/N 2WB1031-6494
4W2547-PAGE 164, 2W6312-PAGE 167 & 2W8576-PAGE 168

7W-0067 PUMP GP-GOV & FUEL INJ

7W0067 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6495-9233
9Y1234-PAGE 153, 4W2547-PAGE 164, 2W6660-PAGE 167.01 & 2W8576-PAGE 168

7W-0067 PUMP GP-GOV & FUEL INJ

7W0067 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, & 4P1383-PAGE 164.04

7C-2192 PUMP GP-GOV & FUEL INJ

7C2192 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB3244-6141
4W2549-PAGE 164.02, 2W6660-PAGE 167.01, 2W8576-PAGE 169B

7C-2192 PUMP GP-GOV & FUEL INJ

7C2192 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6142-9233
4W2549-PAGE 164.02, 2W8576-PAGE 169B, 2W6660-PAGE 167.01 &
9Y1234-PAGE 153

7C-2192 PUMP GP-GOV & FUEL INJ

7C2192 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 4P1381-PAGE 164.03

2W-8576 GOVERNOR GP

2W8576 GOVERNOR GP-PART 1 OF 3
TYPE 1
PART OF 7W0066, 7W0067, 2W8543, 2W9103 & 7E0257 PUMPS

2W-8576 GOVERNOR GP

2W8576 GOVERNOR GP-PART 2 OF 3
TYPE 1
PART OF 7W0066, 7W0067, 2W8543, 2W9103 & 7E0257 PUMPS

2W-8576 GOVERNOR GP

2W8576 GOVERNOR GP-PART 3 OF 3
TYPE 1
PART OF 7W0066, 7W0067, 2W8543, 2W9103 & 7E0257 PUMPS

2W-8576 GOVERNOR GP

2W8576 GOVERNOR GP-PART 1 OF 3
TYPE 2
PART OF 2W8543, 2W9103, 7C2192, 7E0257 & 4P0667 PUMPS

2W-8576 GOVERNOR GP

2W8576 GOVERNOR GP-PART 2 OF 3
TYPE 2
PART OF 2W8543, 2W9103, 7C2192, 7E0257, & 4P0667 PUMPS

2W-8576 GOVERNOR GP

2W8576 GOVERNOR GP-PART 3 OF 3
TYPE 2
PART OF 2W8543, 2W9103, 7C2192, 7E0257, & 4P0667 PUMPS

8N-1730 CONTROL GP-GOVERNOR

8N1730 CONTROL GP-GOVERNOR-WOODWARD 2301 LOAD SHARING
REPLACED BY 7W6542-PAGE 172.01
1018923-PAGE 174A.04
AN ATTACHMENT

1N-5331 CONTROL GP-GOVERNOR

1N5331 CONTROL GP-GOVERNOR
AN ATTACHMENT

7W-6542 CONTROL GP-GOVERNOR

7W6542 CONTROL GP-GOVERNOR
TYPE 2. 1315454-PAGE 172.01.01
WOODWARD-2301 LOADSHARING
AN ATTACHMENT

7W-6542 CONTROL GP-GOVERNOR

7W6542 CONTROL GP-GOVERNOR
TYPE 1. 1018923-PAGE 172.02
WOODWARD-2301 LOADSHARING
AN ATTACHMENT

7C-0246 CONTROL AS-GOVERNOR

7C0246 CONTROL AS-GOVERNOR

131-5454 CONTROL AS-GOVERNOR

1315454 CONTROL AS-GOVERNOR
PART OF 7W6542 CONTROL-GOVERNOR
AN ATTACHMENT

101-8923 CONTROL AS-GOVERNOR

1018923 CONTROL AS-GOVERNOR
PART OF 7W6542 CONTROL
AN ATTACHMENT

108-0136 CONTROL GP-GOVERNOR

1080136 CONTROL GP-GOVERNOR
AN ATTACHMENT

4N-3831 CONTROL GP-GOVERNOR

4N3831 GOVERNOR CONTROL GROUP-VERNIER & POSITIVE LOCKING
4N3829-PAGE 175
AN ATTACHMENT

8N-1731 CONTROL GP-GOVERNOR

8N1731 GOVERNOR CONTROL GP-WOODWARD 2301 STANDBY
REPLACED BY 7W6543-PAGE 174
AN ATTACHMENT

7W-6543 CONTROL GP-GOVERNOR

7W6543 GOVERNOR CONTROL GROUP
AN ATTACHMENT

1W-7411 CONTROL GP-GOVERNOR

1W7411 GOVERNOR CONTROL GROUP-L.H.-VERNIER & POSITIVE LOCK
4N3829-PAGE 175. AN ATTACHMENT

2W-3469 CONTROL GP-GOVERNOR

2W3469 GOVERNOR CONTROL GROUP-28 VOLT, DC MOTOR-TYPE 1
4N3828-PAGE 175
AN ATTACHMENT

2W-3469 CONTROL GP-GOVERNOR

2W3469 GOVERNOR CONTROL GROUP-28 VOLT, DC MOTOR-TYPE 2
4N3828-PAGE 175
AN ATTACHMENT

2W-3469 CONTROL GP-GOVERNOR

2W3469 CONTROL GP-GOVERNOR-28 VOLT, DC MOTOR-TYPE 3
4N3828-PAGE 175
AN ATTACHMENT

4N-3829 CONTROL GP-GOVERNOR

4N3829 CONTROL GP-GOVERNOR-VERNIER & POSITIVE LOCK
PART OF 4N3831 & 1W7411 GOVERNOR CONTROL
AN ATTACHMENT

4N-3828 CONTROL GP-GOVERNOR

4N3828 GOVERNOR CONTROL GROUP-REMOTE & POSITIVE LOCK
PART OF 2W3469 GOVERNOR. AN ATTACHMENT

LINES GP-FUEL

2W-3452 LINES GP-FUEL FILTER

2W3452 LINES GP-FUEL FILTER
S/N 2WB1-6041

2W-3452 LINES GP-FUEL FILTER

2W3452 LINES GP-FUEL FILTER
S/N 2WB6042-UP

2W-7595 LINES GP-FUEL FILTER

2W7595 FUEL FILTER LINES GP
REFER TO 3N8700 CHART SHOWN ON PAGE 234. AN ATTACHMENT

4N-5349 LINES GP-FUEL FILTER

4N5349 FUEL FILTER LINES GROUP
FOR USE WITH 8H7204 PRIMARY FUEL FILTER-PAGE 141
AN ATTACHMENT

2W-3457 LINES GP-FUEL FILTER

2W3457 LINES GP-FUEL FILTER
S/N 2WB1-6041
FOR USE WITH 8H7204 PRIMARY FILTER-PAGE 141
AN ATTACHMENT

9Y-4812 LINES GP-FLEXIBLE FUEL

9Y4812 LINES GP-FLEXIBLE FUEL
AN ATTACHMENT

2W-3457 LINES GP-FUEL FILTER

2W3457 LINES GP-FUEL FILTER
S/N 2WB6042-UP
FOR USE WITH 8H7204 PRIMARY FILTER-PAGE 141
AN ATTACHMENT

3N-6668 LINES GP-FLEXIBLE FUEL

3N6668 FLEXIBLE FUEL LINES GROUP
AN ATTACHMENT

4W-0423 DRAIN GP-FUEL

4W423 DRAIN GP-FUEL
TYPE 1-LINES & ALARM SWITCH
FOR USE WITH DOUBLE WALLED INJECTION LINES
AN ATTACHMENT

4W-0423 DRAIN GP-FUEL

4W0423 DRAIN GP-FUEL
TYPE 2-LINES & ALARM SWITCH
FOR USE WITH DOUBLE WALLED FUEL INJECTION LINES
AN ATTACHMENT

7E-3039 DRAIN GP-FUEL

7E3039 DRAIN GP-FUEL
S/N 2WB6495-UP. LINES & ALARM SWITCH
FOR USE WITH DOUBLE WALLED INJECTION LINES
AN ATTACHMENT

1W-0557 LINES GP-FUEL INJECTION

1W0557 FUEL INJECTION LINES GROUP
S/N 2WB1-1676
2W3777 & 2W3776-PAGE 152

1W-0557 LINES GP-FUEL INJECTION

1W0557 LINES GP-FUEL INJECTION
S/N 2WB1677-2994
2W3776 & 2W3777-PAGE 152, 4W7017-PAGE 151.03

1W-0557 LINES GP-FUEL INJECTION

1W0557 LINES GP-FUEL INJECTION
S/N 2WB2995-3383
4W7017-PAGE 151.03, 7W8627 & 7W8628-PAGE 152.00.01

1W-0557 LINES GP-FUEL INJECTION

1W0557 LINES GP-FUEL INJECTION
S/N 2WB3384-4119
4W7017-PAGE 151.03, 7C2107 & 7C2108-PAGE 152.00.02

1W-0557 LINES GP-FUEL INJECTION

1W0557 LINES GP-FUEL INJECTION
S/N 2WB4120-4622
4W7017-PAGE 151.03, 7C3418 & 7C3428-PAGE 152.00.03

1W-0557 LINES GP-FUEL INJECTION

1W0557 LINES GP-FUEL INJECTION
S/N 2WB4623-UP
4W7017-PAGE 151.03, 7C9935 & 7C9936-PAGE 152.00.04 & 7C9937-PAGE 152.00.05

4W-1566 LINES GP-FUEL INJECTION

4W1566 LINES GP-FUEL INJECTION
S/N 2WB5164-6875
4W7017-PAGE 151.03, 7C9935 & 7C9936-PAGE 152.00.04,
7C9937-PAGE 152.00.05

4W-1566 LINES GP-FUEL INJECTION

4W1566 LINES GP-FUEL INJECTION
S/N 2WB6876-9233
4W7017-PAGE 151.03, 7C9935 & 7C9936-PAGE 152.00.04,
7C9937-PAGE 152.00.05

4W-1566 LINES GP-FUEL INJECTION

4W1566 LINES GP-FUEL INJECTION
S/N 2WB9234-10807
4W7017-PAGE 151.03, 4P3673-PAGE 152.00.05
4P3674 & 4P3675-PAGE 152.00.06

4W-1566 LINES GP-FUEL INJECTION

4W1566 LINES GP-FUEL INJECTION
S/N 2WB10808-11354
4W7017-PAGE 151.03, 4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

4W-1566 LINES GP-FUEL INJECTION

4W1566 LINES GP-FUEL INJECTION
S/N 2WB11355-UP
4W7017-PAGE 151.03, 4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

9Y-3070 LINES GP-FUEL INJECTION

9Y3070 LINES GP-FUEL INJECTION
TYPE 1. S/N 2WB9234-UP
4P3673-PAGE 152.00.05, 4P3675 & 4P3674-PAGE 152.00.06

9Y-3070 LINES GP-FUEL INJECTION

9Y3070 LINES GP-FUEL INJECTION
TYPE 2. S/N 2WB9234-UP
4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

9Y-3070 LINES GP-FUEL INJECTION

9Y3070 LINES GP-FUEL INJECTION
TYPE 3. S/N 2WB9234-UP
4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

4W-8293 LINES GP-FUEL INJECTION

4W8293 FUEL INJECTION LINES GROUP
S/N 2WB1-1676
2W3776 & 2W3777-PAGE 152

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB1677-2994
2W3776 & 2W3777-PAGE 152

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB2995-3383
7W8627 & 7W8628-PAGE 152.00.01

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB3384-4119
4W7018-PAGE 151.02, 7C2107 & 7C2108-PAGE 152.00.02

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB4120-4622
4W7018-PAGE 151.02, 7C3418 & 7C3428-PAGE 152.00.03

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB4623-6875
4W7018-PAGE 151.02, 7C9935 & 7C9936-PAGE 152.00.04 &
7C9937-PAGE 152.00.05

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB6876-9233
4W7018-PAGE 151.02, 7C9935 & 7C9936-PAGE 152.00.04 & 7C9937-PAGE 152.00.05

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB9234-11414
4W7018-PAGE 151.02, 4P3673-PAGE 152.00.05
4P3674 & 4P3675-PAGE 152.00.06

4W-8293 LINES GP-FUEL INJECTION

4W8293 LINES GP-FUEL INJECTION
S/N 2WB11415-UP
4W7018-PAGE 151.02, 4P9658-PAGE 152.00.07,
4P9659-PAGE 152.00.07 & 4P9660-PAGE 152.00.08

2W-3776 LINES GP-FUEL INJECTION

2W3776 LINES GP-FUEL INJECTION
S/N 2WB1-2994
PART OF 1W0557 & 4W8293 FUEL INJECTION LINES

2W-3777 LINES GP-FUEL INJECTION

2W3777 LINES GP-FUEL INJECTION
S/N 2WB1-2994
PART OF 1W0557 & 4W8293 FUEL INJECTION LINES

7W-8628 LINES GP-FUEL INJECTION

7W8628 LINES GP-FUEL INJECTION
S/N 2WB2995-3383
PART OF 1W0557 & 4W8293 FUEL INJECTION LINES

7W-8627 LINES GP-FUEL INJECTION

7W8627 LINES GP-FUEL INJECTION
S/N 2WB2995-3383
PART OF 1W0557 & 4W8293 FUEL INJECTION LINES

7C-2108 LINES GP-FUEL INJECTION

7C2108 LINES GP-FUEL INJECTION
S/N 2WB3384-4119
PART OF 1W0557, 4W8293 LINES-FUEL INJECTION

7C-2107 LINES GP-FUEL INJECTION

7C2107 LINES GP-FUEL INJECTION
S/N 2WB3384-4119
PART OF 1W0557, 4W8293 LINES-FUEL INJECTION

7C-3428 LINES GP-FUEL INJECTION

7C3428 LINES GP-FUEL INJECTION
S/N 2WB4120-4622
PART OF 1W0557 & 4W8293 FUEL INJECTION LINES

7C-3418 LINES GP-FUEL INJECTION

7C3418 LINES GP-FUEL INJECTION
S/N 2WB4120-4622
PART OF 1W0557 & 4W8293 LINES-FUEL INJECTION

7C-9936 LINES GP-FUEL INJECTION

7C9936 LINES GP-FUEL INJECTION
S/N 2WB4623-UP
PART OF 1W0557, 4W1566 & 4W8293 FUEL INJECTION LINES

7C-9935 LINES GP-FUEL INJECTION

7C9935 LINES GP-FUEL INJECTION
S/N 2WB4623-UP
PART OF 1W0557, 4W1566 & 4W8293 FUEL INJECTION LINES

4P-3673 LINES GP-FUEL INJECTION

4P3673 LINES GP-FUEL INJECTION
S/N 2WB9234-UP
PART OF 4W1566, 7E0258, 7E0259, 9Y3070, & 4W8293 FUEL INJECTION LINES

7C-9937 LINES GP-FUEL INJECTION

7C9937 LINES GP-FUEL INJECTION
S/N 2WB4623-UP
PART OF 1W0557, 4W1566 & 4W8293 FUEL INJECTION LINES

4P-3675 LINES GP-FUEL INJECTION

4P3675 LINES GP-FUEL INJECTION
S/N 2WB9234-UP
PART OF 4W1566, 7E0258, 7E0259, 9Y3070 & 4W8293 FUEL INJECTION LINES

4P-3674 LINES GP-FUEL INJECTION

4P3674 LINES GP-FUEL INJECTION
S/N 2WB9234-UP
PART OF 4W1566, 7E0258, 7E0259, 9Y3070, & 4W8293 FUEL INJECTION LINES

4P-9659 LINES GP-FUEL INJECTION

4P9659 LINES GP-FUEL INJECTION
PART OF 7E0258, 7E0259, 4W1566, 4W8293 &
9Y3070 FUEL INJECTION LINES

4P-9658 LINES GP-FUEL INJECTION

4P9658 LINES GP-FUEL INJECTION
PART OF 7E0258, 7E0259, 4W1566, 4W8293 &
9Y3070 FUEL INJECTION LINES

4P-9660 LINES GP-FUEL INJECTION

4P9660 LINES GP-FUEL INJECTION
PART OF 7E0258, 7E0259, 4W1566, 4W8293 &
9Y3070 FUEL INJECTION LINES

1W-3138 LINES GP-FUEL INJECTION

1W3138 LINES GP-FUEL INJECTION
TYPE 2. 7C4307 & 7C4308-PAGE 152.03
FOR USE WITH DOUBLE WALLED FUEL LINES DRAIN
AN ATTACHMENT

1W-3138 LINES GP-FUEL INJECTION

1W3138 LINES GP-FUEL INJECTION
TYPE 1. 2W3783 & 2W3792-PAGE 152.02
FOR USE WITH DOUBLE WALLED FUEL LINES DRAIN
AN ATTACHMENT

2W-3792 LINES GP-FUEL INJECTION

2W3792 FUEL INJECTION LINES GROUIP-DOUBLE WALLED
PART OF 1W3138 FUEL INJECTION LINES
AN ATTACHMENT

2W-3783 LINES GP-FUEL INJECTION

2W3783 FUEL INJECTION LINES GROUP-DOUBLE WALLED
PART OF 1W3138 FUEL INJECTION LINES
AN ATTACHMENT

7C-4308 LINES GP-FUEL INJECTION

7C4308 LINES GP-FUEL INJECTION
PART OF 1W3138 LINES-FUEL INJECTION
AN ATTACHMENT

7C-4307 LINES GP-FUEL INJECTION

7C4307 LINES GP-FUEL INJECTION
PART OF 1W3138 LINES-FUEL INJECTION
AN ATTACHMENT

7E-0258 LINES GP-FUEL INJECTION

7E0258 LINES GP-FUEL INJECTION
TYPE 1
4P3673-PAGE 152.00.05, 4P3674 & 4P3675-PAGE 152.00.06

7E-0258 LINES GP-FUEL INJECTION

7E0258 LINES GP-FUEL INJECTION
TYPE 2
4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

7E-0258 LINES GP-FUEL INJECTION

7E0258 LINES GP-FUEL INJECTION
TYPE 3
4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

7E-0259 LINES GP-FUEL INJECTION

7E0259 LINES GP-FUEL INJECTION
TYPE 1
4P3673-PAGE 152.00.05, 4P3674 & 4P3675-PAGE 152.00.06

7E-0259 LINES GP-FUEL INJECTION

7E0259 LINES GP-FUEL INJECTION
TYPE 2
4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

7E-0259 LINES GP-FUEL INJECTION

7E0259 LINES GP-FUEL INJECTION
TYPE 3
4P9658 & 4P9659-PAGE 152.00.07, 4P9660-PAGE 152.00.08

PUMP GP-FUEL INJECTION

4W-7018 NOZZLE AS-FUEL VALVE

4W7018 NOZZLE AS-FUEL VALVE-*R
S/N 2WB1677-UP
PART OF 4W8293 LINES-FUEL INJECTION

4W-7017 NOZZLE AS-FUEL VALVE

4W7017 NOZZLE AS-FUEL VALVE-D.I.*R
S/N 2WB1677-UP
PART OF 1W0557 & 4W1566 LINES-FUEL INJECTION

9Y-1234 FASTENER GP-FUEL INJ PUMP

9Y1234 FASTENER GP
S/N 2WB1031-UP
PART OF 7C2192, 7W0066, 7W0067, 2W8543, 2W9103, 7E0257, 4P0667 PUMPS

1W-7376 FASTENER GP-FUEL INJ PUMP

1W7376 FASTENER GP-FUEL INJECTION PUMP

1W-6378 DRIVE GP-GOVERNOR & FUEL PUMP

1W6378 GOVERNOR & FUEL PUMP DRIVE GROUP - TYPE 1

1W-6378 DRIVE GP-GOVERNOR & FUEL PUMP

1W6378 GOVERNOR & FUEL PUMP DRIVE GROUP - TYPE 2

7E-7269 DRIVE GP-GOVERNOR & FUEL PUMP

7E7269 DRIVE GP-GOVERNOR & FUEL PUMP

4P-1365 DRIVE GP-GOVERNOR & FUEL PUMP

4P1365 DRIVE GP-GOVERNOR & FUEL PUMP

7W-0043 PUMP GP-GOV & FUEL INJ

7W0043 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
26 DEG. TIMING. S/N 2WB1031-6494
1W1205-PAGE 160, 4W2547-PAGE 164

7W-0043 PUMP GP-GOV & FUEL INJ

7W0043 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
26 DEG. TIMING. S/N 2WB6495-9233
1W1205-PAGE 160, 4W2547-PAGE 164

7W-0043 PUMP GP-GOV & FUEL INJ

7W0043 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
26 DEG. TIMING. S/N 2WB9234-UP
1W1205-PAGE 160, 4P1383-PAGE 164.04

2W-8030 PUMP GP-GOV DRIVE & FUEL INJ

2W8030 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB1-7564
1W1205-PAGE 160 & 2W6972-PAGE 163

2W-8030 PUMP GP-GOV DRIVE & FUEL INJ

2W8030 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB7565-9233
1W1205-PAGE 160, 7E7267-PAGE 163.01

2W-8030 PUMP GP-GOV DRIVE & FUEL INJ

2W8030 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB9234-UP
1W1205-PAGE 160, 4P1385-PAGE 164.04.01

7W-9008 PUMP GP-GOV DRIVE & FUEL INJ

7W9008 PUMP GP-GOVERNOR DRIVE & FUEL INJECTION
S/N 2WB3244-9233
1W1205-PAGE 160, 4W2549-PAGE 164.02

7W-9008 PUMP GP-GOV DRIVE & FUEL INJ

7W9008 PUMP GP-GOVERNOR DRIVE
S/N 2WB9234-UP
1W1205-PAGE 160, 4P1381-PAGE 164.03

2W-6972 PUMP GP-FUEL INJECTION

2W6972 FUEL INJECTION PUMP GROUP
TYPE 1
PART OF 2W8030, 2W9103, & 2W8543 GOVERNOR

7E-7267 PUMP GP-FUEL INJECTION

7E7267 PUMP GP-FUEL INJECTION
PART OF 2W8030, 2W8543, 4P0667, & 2W9103 PUMPS

2W-6972 PUMP GP-FUEL INJECTION

2W6972 PUMP GP-FUEL INJECTION
TYPE 2
PART OF 2W8030 & 2W8543 GOVERNOR & FUEL INJECTION PUMP

4W-2547 PUMP GP-FUEL INJECTION

4W2547 PUMP GP- FUEL INJECTION
S/N 2WB1031-9233. TYPE 1
PART OF 7W0043, 7W0066, & 7W0067 GOVERNOR DRIVE & FUEL INJECTION PUMP

4W-2547 PUMP GP-FUEL INJECTION

4W2547 PUMP GP-FUEL INJECTION
S/N 2WB1031-9233. TYPE 2
PART OF 7W0043, 7W0066, & 7W0067 GOVERNOR DRIVE & FUEL INJECTION PUMP

4W-2547 PUMP GP-FUEL INJECTION

4W2547 PUMP GP-FUEL INJECTION
S/N 2WB9234-UP
PART OF 7W0043, 7W0066, & 7W0067 FUEL INJECTION PUMPS

4W-2549 PUMP GP-FUEL INJECTION

4W2549 PUMP GP-FUEL INJECTION
PART OF 7W9008 & 7C2192 GOVERNOR & FUEL INJECTION PUMPS

4P-1381 PUMP GP-FUEL INJECTION

4P1381 PUMP GP-FUEL INJECTION
TYPE 1 S/N 2WB9234-UP
7E6006-PAGE 166F.01
PART OF 7W9008, 7E0257, & 7C2192 PUMPS-FUEL INJECTION

4P-1381 PUMP GP-FUEL INJECTION

4P1381 PUMP GP-FUEL INJECTION
TYPE 2 S/N 2WB9234-UP
4P7681-PAGE 166F.01
PART OF 7W9008, 7E0257, & 7C2192 PUMPS-FUEL INJECTION

4P-1381 PUMP GP-FUEL INJECTION

4P1381 PUMP GP-FUEL INJECTION
TYPE 3 S/N 2WB9234-UP
1086633-PAGE 166F.02
PART OF 7W9008, 7E0257, & 7C2192 PUMPS-FUEL INJECTION

4P-1383 PUMP GP-FUEL INJECTION

4P1383 PUMP GP-FUEL INJECTION
TYPE 1. S/N 2WB9234-UP
7E6006-PAGE 166F.01
PART OF 7W0043, 7W0066, 7W0067 FUEL INJECTION PUMPS

4P-1383 PUMP GP-FUEL INJECTION

4P1383 PUMP GP-FUEL INJECTION
TYPE 2. S/N 2WB9234-UP
4P7681-PAGE 166F.01
PART OF 7W0043, 7W0066, 7W0067 FUEL INJECTION PUMPS

4P-1383 PUMP GP-FUEL INJECTION

4P1383 PUMP GP-FUEL INJECTION
TYPE 3. S/N 2WB9234-UP
1086633-PAGE 166F.02
PART OF 7W0043, 7W0066, 7W0067 FUEL INJECTION PUMPS

4P-1385 PUMP GP-FUEL INJECTION

4P1385 PUMP GP-FUEL INJECTION
TYPE 1. 7E6006-PAGE 166F.01
PART OF 2W8030, 2W8543, 2W9103, & 4P0667 FUEL INJECTION PUMPS

4P-1385 PUMP GP-FUEL INJECTION

4P1385 PUMP GP-FUEL INJECTION
TYPE 2. 4P7681-PAGE 166F.01
PART OF 2W8030, 2W8543, 2W9103, & 4P0667 FUEL INJECTION PUMPS

7E-0257 PUMP GP-GOV & FUEL INJ

7E0257 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB11415-UP
2W6660-PAGE 167.01, 9Y1234-PAGE 153
2W8576-PAGE 168, 4P1381-PAGE 164.03

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 PUMP GP-GOVERNOR & FUEL INJECTION
TYPE 1. S/N 2WB1-6141
2W6972-PAGE 163, 2W6312-PAGE 167 & 2W8576-PAGE 168

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 PUMP GP-GOVERNOR & FUEL INJECTION
TYPE 2. S/N 2WB1-6141
2W6972-PAGE 163, 2W8576-PAGE 168 & 2W6660-PAGE 167.01

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6142-7564
2W6972-PAGE 163, 2W8576-PAGE 168, 2W6660-PAGE 167.01 &
9Y1234-PAGE 153

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB7565-8181
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 7E7267-PAGE 163.01

2W-8543 PUMP GP-GOV & FUEL INJ

2W8543 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB8182-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 4P1385-PAGE 164.04.01

4P-0667 PUMP GP-GOV & FUEL INJ

4P0667 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB8192-9233
2W6660-PAGE 167.01, 9Y1234-PAGE 153
2W8576-PAGE 169B, 7E7267-PAGE 163.01

4P-0667 PUMP GP-GOV & FUEL INJ

4P0667 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W6660-PAGE 167.01, 9Y1234-PAGE 153
2W8576-PAGE 169B, 4P1385-PAGE 164.04.01

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 PUMP GP-GOVERNOR & FUEL INJECTION
S/N 2WB1-2975
2W6972-PAGE 163, 2W6312-PAGE 167, 2W8576-PAGE 168

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 PUMP GP-GOVERNOR & FUEL INJECTION
S/N 2WB2976-6141
2W6972-PAGE 163, 2W6660-PAGE 167.01, 2W8576-PAGE 168

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6142-7564
2W6972-PAGE 163, 2W8576-PAGE 168 & 9Y1234-PAGE 153
2W6660-PAGE 167.01

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB7565-9233
2W6660-PAGE 167.01, 2W8576-PAGE 168
9Y1234-PAGE 153, 7E7267-PAGE 163.01

2W-9103 PUMP GP-GOV & FUEL INJ

2W9103 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W6660-PAGE 167.01, 2W8576-PAGE 168, 9Y1234-PAGE 153
4P1385-PAGE 164.04.01

7W-0066 PUMP GP-GOV & FUEL INJ

7W0066 GOVERNOR & FUEL INJECTION PUMP GP
TYPE 1. S/N 2WB1031-9233
4W2547-PAGE 164, 2W6312-PAGE 167 & 2W8576-PAGE 168

7W-0066 PUMP GP-GOV & FUEL INJ

7W0066 GOVERNOR & FUEL INJECTION PUMP GP
TYPE 2. S/N 2WB1031-9233
9Y1234-PAGE 153, 4W2547-PAGE 164, 2W6660-PAGE 167.01 & 2W8576-PAGE 168

7W-0066 PUMP GP-GOV & FUEL INJ

7W0066 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 4P1383-PAGE 164.04

7W-0067 PUMP GP-GOV & FUEL INJ

7W0067 PUMP GP-GOVERNOR & FUEL INJECTION
S/N 2WB1031-6494
4W2547-PAGE 164, 2W6312-PAGE 167 & 2W8576-PAGE 168

7W-0067 PUMP GP-GOV & FUEL INJ

7W0067 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6495-9233
9Y1234-PAGE 153, 4W2547-PAGE 164, 2W6660-PAGE 167.01 & 2W8576-PAGE 168

7W-0067 PUMP GP-GOV & FUEL INJ

7W0067 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, & 4P1383-PAGE 164.04

7C-2192 PUMP GP-GOV & FUEL INJ

7C2192 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB3244-6141
4W2549-PAGE 164.02, 2W6660-PAGE 167.01, 2W8576-PAGE 169B

7C-2192 PUMP GP-GOV & FUEL INJ

7C2192 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB6142-9233
4W2549-PAGE 164.02, 2W8576-PAGE 169B, 2W6660-PAGE 167.01 &
9Y1234-PAGE 153

7C-2192 PUMP GP-GOV & FUEL INJ

7C2192 GOVERNOR & FUEL INJECTION PUMP GP
S/N 2WB9234-UP
2W8576-PAGE 168, 2W6660-PAGE 167.01
9Y1234-PAGE 153, 4P1381-PAGE 164.03

4P-7681 PUMP GP-FUEL INJECTION

4P7681 PUMP GP-FUEL INJECTION
PART OF 4P1385, 4P1381, 4P1383 FUEL INJECTION PUMPS

7E-6006 PUMP GP-FUEL INJECTION

7E6006 PUMP GP-FUEL INJECTION
PART OF 4P1381, 4P1383, & 4P1385 FUEL INJECTION PUMPS

108-6633 PUMP GP-FUEL INJECTION

1086633 PUMP GP-FUEL INJECTION
S/N 2WB9234-UP
PART OF 4P1381 & 4P1383 PUMPS-FUEL INJECTION

PUMP GP-FUEL PRIMING

4N-3287 PUMP GP-FUEL PRIMING

4N3287 PUMP GP-FUEL PRIMING

PUMP GP-FUEL TRANSFER

1W-1700 PUMP GP-FUEL TRANSFER

1W1700 PUMP GP-FUEL TRANSFER*R
S/N 2WB1-1043
PART OF 2W4381 PUMP-PUMP-FUEL TRANSFER

2W-4381 PUMP GP-FUEL TRANSFER

2W4381 PUMP GP-FUEL TRANSFER
1W1700-PAGE 147

1W-1700 PUMP GP-FUEL TRANSFER

1W1700 PUMP GP-FUEL TRANSFER*R
S/N 2WB1044-2692
PART OF 2W4381 PUMP-FUEL TRANSFER

1W-1700 PUMP GP-FUEL TRANSFER

1W1700 PUMP GP-FUEL TRANSFER*R
S/N 2WB7841-UP
PART OF 2W4381 FUEL TRANSFER PUMP

1W-1700 PUMP GP-FUEL TRANSFER

1W1700 PUMP GP-FUEL TRANSFER*R
S/N 2WB2693-7840
PART OF 2W4381 FUEL TRANSFER PUMP

4W-1727 COVER GP-FUEL TRANSFER

4W1727 COVER GP-FUEL TRANSFER
REQUIRED WHEN TACHOMETER DRIVE AND/OR SERVICE METER IS NOT INSTALLED
PART OF 7W9662 MOUNTING CONTACTOR. AN ATTACHMENT

SEPARATOR GP-WATER

2W-4234 SEPARATOR GP-WATER

2W4234 SEPARATOR GP-WATER
FOR USE WITH MARINE PROPULSION & MARINE AUXILIARY ENGINES
AN ATTACHMENT

SHUTOFF GP

2W-9161 SHUTOFF GP-MANUAL

2W9161 SHUT-OFF GROUP-MANUAL
ALSO AN ATTACHMENT

2N-8902 SHUTOFF GP

2N8902 SOLENOID SHUT-OFF GROUP-12 VOLT
FOR USE WITH PSG GOVERNOR. AN ATTACHMENT

TANK GP-FUEL

5N-2016 TANK & BASE GP-FUEL

5N2016 FUEL TANK & BASE GROUP
REPLACED BY 4W9271-PAGE 149A. FOR USE WITH PACKAGED GENERATOR
SET & BATTERY RACK. NOT FOR USE WITH LIFTING ARCH
AN ATTACHMENT

4W-9271 TANK & BASE GP-FUEL

4W9271 TANK & BASE GP-FUEL
NOT FOR USE WITH ENCLOSURE OR LIFTING ARCH
AN ATTACHMENT

8N-7153 TANK & BASE GP-FUEL

8N7153 FUEL TANK & BASE GROUP
REPLACED BY 4W9275-PAGE 150. FOR USE WITH LIFTING ARCH &
BATTERY RACK. AN ATTACHMENT

7W-9331 TANK & BASE GP-FUEL

7W9331 TANK & BASE GP-FUEL
AN ATTACHMENT

9Y-5783 TANK & BASE GP-FUEL

9Y5783 BASE & FUEL TANK GP
3N8594-PAGE 53
AN ATTACHMENT

4W-9275 TANK & BASE GP-FUEL

4W9275 FUEL TANK & BASE GROUP
FOR USE WITH ENCLOSURE & LIFTING ARCH
AN ATTACHMENT

7W-9332 TANK & BASE GP-FUEL

7W9332 TANK GP-BASE & FUEL
AN ATTACHMENT

TORQUE CONTROL GP

4W-3912 TORQUE CONTROL GP

4W3912 TORQUE CONTROL GROUP
AN ATTACHMENT

2W-6312 TORQUE CONTROL GP

2W6312 TORQUE CONTROL GROUP
PART OF 2W8543, 7W67, 7W66 & 2W9103 GOVERNOR & FUEL PUMP

2W-6660 TORQUE CONTROL GP

2W6660 TORQUE CONTROL GP
PART OF 2W9103, 7C2192, 7W0066, 7W0067, 2W8543,
7E0257, 4P0667, 1108896 PUMPS

Information:

(For parts list, see above)

FUEL SYSTEM

CAMSHAFT AS

Engine News

Cat® Reman Announces the Availability of Additional Engine Components for Certain Engine Applications {1052, 1053, 108F, 1210, 1265, 1290, 1405, 1901, 5510}
2015/06/26

Special Instruction

3406 New Scroll Fuel System (NSFS) Camshaft Plugs{1110}
3406 New Scroll Fuel System (NSFS) Camshaft Plugs{1110}

Service Magazine

New Fuel Injection Pump Groups Have Larger Diameter Camshaft Bores, New Lifter Assembly, And Shorter Plunger And Barrel Assembly{1251,1253,1281,1292}
1992/09/21

CONTROL GP-DECELERATOR

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05

CONTROL GP-FUEL

Engine News

Information For Repair Of Hydraulic Fuel Ratio Controls
1983/08/17

New EG3P Actuator Assemblies Available
1984/03/07

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines
1984/04/11

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel Systems
1985/12/01

Serviceable Parts For New Fuel Ratio Control; Pressurize Control To Set Rack
1987/05/01

New Components Used In Fuel Ratio Control Groups
1992/05/01

Special Instruction

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Service Magazine

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

CONTROL GP-FUEL INJECTION

Special Instruction

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Service Letter-NACD

Product Support Program For Governor Servo Pin Loss On Certain 3304, 3306, 3306B, 3406 And 3406B Engines
Product Support Program For Governor Servo Pin Loss On Certain 3304, 3306, 3306B, 3406 And 3406B Engines

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Americas

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Truck/Ag/Marine

Service Letter-China

Service Letter-Asia

Service Letter-APD

Service Magazine

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators{1265,1289}
1984/04/23

Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14

Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02

Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

CONTROL GP-FUEL RATIO

Engine News

Information For Repair Of Hydraulic Fuel Ratio Controls
1983/08/17

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines
1984/04/11

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel Systems
1985/12/01

Serviceable Parts For New Fuel Ratio Control; Pressurize Control To Set Rack
1987/05/01

New Components Used In Fuel Ratio Control Groups
1992/05/01

Cat® Reman Announces New Fuel Pump, Fuel Ratio Control, and Fuel Injector Options for Certain Engines {1251, 1278}
2014/09/05

Cat® Reman Announces Additions to the Fuel Air Ratio Controls Portfolio for Certain Engine Applications {1278}
2015/06/26

Special Instruction

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Service Magazine

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings{1250,1264,1278,1287}
1985/11/11

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

CONTROL GP-GOVERNOR

Engine News

Information For Repair Of Hydraulic Fuel Ratio Controls
1983/08/17

New EG3P Actuator Assemblies Available
1984/03/07

Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators
1984/05/16

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct
1986/05/01

FT Tooling Prints Available For Bushing Installation In Governor Housing
1986/05/01

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups
1986/06/01

Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01

Serviceable Parts For New Fuel Ratio Control; Pressurize Control To Set Rack
1987/05/01

Governor Control Motor Polarity May Require A Change
1990/11/01

Improved Governor Raise/Lower Motor Used In Governor Control Groups{1264}
1998/03/01

Cat® Reman Announces the Availability of Additional Engine Components for Certain Engine Applications {1052, 1053, 108F, 1210, 1265, 1290, 1405, 1901, 5510}
2015/06/26

Special Instruction

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Installation of 7C7466 Solenoid Repair Kit{1259}
Installation of 7C7466 Solenoid Repair Kit{1259}

Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}

Service Letter-NACD

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Americas

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Truck/Ag/Marine

Specifications

Governor Linkage (Woodward PSG) (3406B)
3406 & 3406B GENERATOR SET ENGINE

Governor Linkage (Woodward PSG) (3406)
3406 & 3406B GENERATOR SET ENGINE

Governor Controls
3400 GENERATOR SET ENGINE ATTACHMENTS

Governor Linkage - 3406 (Woodward EG-3P)
3400 GENERATOR SET ENGINE ATTACHMENTS

Governor Linkage-3406B (Woodward EG-3P Actuator)
3400 GENERATOR SET ENGINE ATTACHMENTS

Governor Linkage - 3408 & 3412 (Woodward EG-3P)
3400 GENERATOR SET ENGINE ATTACHMENTS

Service Letter-China

Service Letter-Asia

Service Letter-APD

Service Magazine

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Correct Wiring And Fuse Must Be Used For Correct Operation Of Shut-Off Solenoid Group{1259}
1984/01/30

Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators{1265,1289}
1984/04/23

Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14

Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05

FT Tooling Prints Available For Bushing Installation In Governor Housing{0600,1287}
1986/05/05

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

DRIVE GP-TACHOMETER

Engine News

Eliminating Interference Between Governor Housing And Tachometer Drive
1985/08/01

Specifications

Fuel Transfer Pump And Tachometer Drive (3406)
3406 & 3406B GENERATOR SET ENGINE

Service Magazine

Eliminating Interference Between Governor Housing And Tachometer Drive{1264,7487}
1985/08/12

FILTER GP-FUEL

Engine News

Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12

Gasket Leakage On Aftermarket Fuel Filters
1986/01/01

Improved Fuel Priming Pump Used
1987/05/01

Improved 1R-0712 Fuel Filter Available{1261}
1994/03/01

Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/23

Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01

A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1260}
A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1260}

Service Letter-NACD

Product Support Program For Replacing Cracked Fuel Lines On Certain 3406C Engines Used In Certain Machine, Commercial, Industrial And Marine Applications
Product Support Program For Replacing Cracked Fuel Lines On Certain 3406C Engines Used In Certain Machine, Commercial, Industrial And Marine Applications

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Truck/Ag/Marine

Specifications

Fuel Filter Base
3406 & 3406B GENERATOR SET ENGINE

Primary Fuel Filter
3400 GENERATOR SET ENGINE ATTACHMENTS

Duplex Fuel Filters (3412)
3400 GENERATOR SET ENGINE ATTACHMENTS

Tool Operating Manual

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

Service Letter-China

Service Letter-Asia

Service Letter-APD

Disassembly and Assembly

Fuel Filter And Base
3406B DIESEL ENGINE FOR GENERATOR SETS

Service Magazine

Gasket Leakage On Aftermarket Fuel Filters{1261}
1985/12/16

New Larger Capacity Water Separator Is Available{1250}
1979/03/12

Lubricant Will Ease Installation Of Secondary Radial Seal Air Filter Element {1054}
1994/04/25

Be Sure To Correctly Tighten 1R-0712, 1R-0740, 1R-0749, 1R-0750, 1R-0751, 1R-0753, And 1R-0759 Fuel Filter Assemblies {1261}
1998/01/26

FUEL AR-HEAVY DISTILLATE

Special Instruction

Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}

Service Magazine

Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13

Diesel Fuel Recommendation Expanded{1280}
1977/02/14

High Sulfur Fuel Can Cause Severe Engine Wear And Internal Damage{1280}
1979/02/05

Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27

Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

FUEL GP-SCREED

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

FUEL SYSTEM GP

Special Instruction

Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}
Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}

Service Letter-NACD

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Truck/Ag/Marine

Tool Operating Manual

NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}

370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

Service Letter-China

Service Letter-Asia

Reuse And Salvage Guidelines

Reuse and Salvage of New Scroll Fuel Systems (NSFS) for 3200, 3300, & 3400 Engines {1250, 1256}
Reuse and Salvage of New Scroll Fuel Systems (NSFS) for 3200, 3300, & 3400 Engines {1250, 1256}

Service Letter-APD

Service Magazine

Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21

New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23

5P7437 Adapter (Part Of 8T5301 Diesel Timing Adapter Group) Must Be Modified To Work On Current Fuel Lines.{0782}
1992/02/03

GAUGE GP

Orifice Fitting Or Snubber Can Help Stop Erratic Fuel Gauge Operation{7456}
1985/06/24

GOVERNOR GP

Engine News

Explanation Of Differences In Timing Advance Information
1981/08/26

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25

Service Information For Woodward Governors
1983/10/26

Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30

New EG3P Actuator Assemblies Available
1984/03/07

Overvoltage Protection For Woodward 2301 Governor
1984/04/11

Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators
1984/05/16

New Valve Assembly And Seal Used In Fuel Transfer Pump
1984/05/16

New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage
1984/06/20

Bonnet Of Fuel Injection Pump Group Now Serviced Separately
1984/12/12

Fill Oil Sump Before Installing Woodward Governor
1985/01/16

Over Fueling Spring No Longer Used In Governor
1985/03/01

Thread Lock Now Used On Timing Advance Bolts
1985/08/01

Eliminating Interference Between Governor Housing And Tachometer Drive
1985/08/01

Special Instruction Available To Salvage Governor Housing
1985/08/01

Fuel Transfer Pump Improved
1985/11/01

Check Fuel Injection Replacement Pump Installation
1985/11/01

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings
1985/12/01

Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01

Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct
1986/05/01

FT Tooling Prints Available For Bushing Installation In Governor Housing
1986/05/01

Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups
1986/06/01

Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01

New Material Used For Disc In Valve Assemblies In Fuel Transfer Pump Groups
1986/09/01

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01

Improved Retaining Bushing In Fuel Injection Pump
1986/12/01

Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01

New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters
1987/10/01

Governor Actuator Now Installed With Shock Mounting
1988/08/01

Governor Control Motor Polarity May Require A Change
1990/11/01

Corrections For Systems Operation, Troubleshooting, And Specifications For 2301 Electric Governors For Generator Set And Industrial Engines, SENR2928-01
1991/05/01

New Speed Setting Clutch Group For 3161 Woodward Governors
1991/06/01

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings
1991/10/01

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings
1992/01/01

Be Sure The Fuel Injection Pump Housing Is Compatible With 0R0715 And 0R2545 Remanufactured Short Blocks
1992/08/01

New Fuel Injection Pump Groups Have Larger Diameter Camshaft Bores, New Lifter Assembly, And Shorter Plunger And Barrel Assembly
1992/09/01

New Bonnet Used In Fuel Injection Pump Group
1993/06/01

Fuel Injection Pump Improvements{1251}
1994/02/01

New Seals In Pump Fastener Group And Fuel Injection Pump Group Have Improved Heat Set Resistance {1251}
1994/09/01

Pressure Compensated Simple Governor (PSG Governor) Changes From Aluminum To Cast Iron Housing {1264}
1995/04/01

Governor Spring Guide Press Depth {1287,1284}
1996/01/17

Woodward Control Assemblies Have Changed Part Numbers To Provide The CE Marking For Electromagnetic Compatibility (EMC) Directives{1264}
1996/05/09

Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/23

Fuel Injection Pump Bushings Have New Groove Adjacent To Load Ring {1251}
1996/11/01

Improved Bushing O-Ring Seal Available For Injection Pump Groups{1251}
1997/03/01

Improvements Made To Remanufactured 0R-3008 Fuel Transfer Pump{1256}
1997/03/01

Improved EG-3P Actuator Assembly For 3406 Engines{1903}
1997/04/01

Improved Governor Raise/Lower Motor Used In Governor Control Groups{1264}
1998/03/01

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13

Special Instruction

Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}

Use of 6V6070 Governor Adjusting Tool Group{1250}
Use of 6V6070 Governor Adjusting Tool Group{1250}

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Wiring Polarity on Woodward 2301 Governors{1289}
Wiring Polarity on Woodward 2301 Governors{1289}

Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}

Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}

Installation Of 4W5391 Preregulator Box Assembly{1289}
Installation Of 4W5391 Preregulator Box Assembly{1289}

Troubleshooting Tips Will Help Maintain Steady Engine RPM{1264, 1280}
Troubleshooting Tips Will Help Maintain Steady Engine RPM{1264, 1280}

Service Letter-NACD

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Americas

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles

3306/3406 Correction of �Overspeed at Start-up� complaint on standby generator set engines
3306/3406 Correction of �Overspeed at Start-up� complaint on standby generator set engines

Specifications

Governor Linkage (Woodward PSG) (3406B)
3406 & 3406B GENERATOR SET ENGINE

Governor (New Scroll Fuel System) (3406B)
3406 & 3406B GENERATOR SET ENGINE

Governor and Fuel Pump Drive Group (3406B)
3406 & 3406B GENERATOR SET ENGINE

Governor Dashpot (3% Regulation) (3406)
3406 & 3406B GENERATOR SET ENGINE

Governor Linkage (Woodward PSG) (3406)
3406 & 3406B GENERATOR SET ENGINE

Governor and Fuel Pump Drive Gear (3406)
3406 & 3406B GENERATOR SET ENGINE

Fuel Transfer Pump And Tachometer Drive (3406)
3406 & 3406B GENERATOR SET ENGINE

Woodward PSG Governor
3406 & 3406B GENERATOR SET ENGINE

Governor Controls
3400 GENERATOR SET ENGINE ATTACHMENTS

Governor Linkage - 3406 (Woodward EG-3P)
3400 GENERATOR SET ENGINE ATTACHMENTS

Governor Linkage-3406B (Woodward EG-3P Actuator)
3400 GENERATOR SET ENGINE ATTACHMENTS

Governor Linkage - 3408 & 3412 (Woodward EG-3P)
3400 GENERATOR SET ENGINE ATTACHMENTS

Service Letter-China

Service Letter-Asia

Systems Operation

Systems Operation
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Installation And Operation
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS

Installation And Operation
2301A SPEED CONTROL

Service Letter-APD

Testing and Adjusting

Testing and Adjusting
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Installation And Operation
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS

Installation And Operation
2301A SPEED CONTROL

Troubleshooting

Introduction
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem Index
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 1: Fuel Linkage Has Limited Travel, Binds, Or Takes Excessive Force
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 2: Engine Will Not Start
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 3: Engine Will Not Carry Load (Low Power)
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 4: Engine Will Not Decelerate. Engine Will Not Idle.
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 5: Engine Speed Not Constant
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 6: Engine Overspeeds
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 7: Engine Does Not Share Load (For Load Share Units Only)
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Problem No. 8: Engine Does Not Parallel
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Service Procedures
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI

Chapter 5. Troubleshooting
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS

Appendix A. Guide for Handling and Protection of Electronic Controls, Printed Circuit Boards, & Modules
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS

Appendix B. EMI Control in Electronic Governing Systems
2301A ELECTRONIC GOVERNORS (LOAD SHARING) FOR GENERATOR SETS

Chapter 5. Troubleshooting
2301A SPEED CONTROL

Appendix A. Guide for Handling and Protection of Electronic Controls, Printed Circuit Boards, & Modules
2301A SPEED CONTROL

Appendix B. EMI Controls in Electronic Governing Systems
2301A SPEED CONTROL

Disassembly and Assembly

Fuel Transfer Pump
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Pump Housing And Governor
3406B DIESEL ENGINE FOR GENERATOR SETS

Governor
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Pumps
3406B DIESEL ENGINE FOR GENERATOR SETS

Service Magazine

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Service Information For Woodward Governors{0374,1264}
1983/09/26

Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07

New EG3P Actuator Assemblies Available{1289}
1984/02/27

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

Overvoltage Protection For Woodward 2301 Governor{1289}
1984/04/09

Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators{1265,1289}
1984/04/23

New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14

New Valve Assembly And Seal Used In Fuel Transfer Pump{1256}
1984/05/14

Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10

Bonnet Of Fuel Injection Pump Group Now Serviced Separately{1251,1250}
1984/12/10

Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14

New Tools Available To Service Fuel Injection Nozzles And Adapters {0706,1254}
1985/01/14

Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04

Over Fueling Spring No Longer Used In Governor{1264,1250}
1985/02/04

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced{1254}
1985/03/18

Special Instruction Available To Salvage Governor Housing{1287}
1985/07/15

Eliminating Interference Between Governor Housing And Tachometer Drive{1264,7487}
1985/08/12

Thread Lock Now Used On Timing Advance Bolts{1272}
1985/08/12

Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02

Fuel Transfer Pump Improved{1256}
1985/10/14

Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28

Check Fuel Injection Replacement Pump Installation{1251,1253,1257}
1985/10/28

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings{1250,1264,1278,1287}
1985/11/11

Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10

Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05

FT Tooling Prints Available For Bushing Installation In Governor Housing{0600,1287}
1986/05/05

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02

Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09

Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16

New Material Used For Disc In Valve Assemblies Of Fuel Transfer Pump Groups{1256}
1986/09/01

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22

Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03

Improved Retaining Bushing In Fuel Injection Pump {1251,1250}
1986/12/01

Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25

Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16

Governor Actuator Now Installed With Shock Mounting{1286}
1988/08/22

9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28

Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06

Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10

Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29

New Speed Setting Clutch Group For 3161 Woodward Governors{1265}
1991/05/20

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings{1253}
1991/09/30

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

Major Engine Component Changes{1201,1202,1205,1218,1219,1230,1253,1288,1331}
1992/09/07

New Fuel Injection Pump Groups Have Larger Diameter Camshaft Bores, New Lifter Assembly, And Shorter Plunger And Barrel Assembly{1251,1253,1281,1292}
1992/09/21

New Bonnet Used In Fuel Injection Pump Group {1251}
1993/06/14

Fuel Injection Pump Improvements{1251}
1994/02/07

HEATER GP-FUEL

Fuel Heaters Are Now Available For Field Installation {1296}
1980/01/07

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

INJECTION GP-CETANE

LINES GP-FUEL

Engine News

Use New Adapter To Make Tests Of 9L6884 Nozzles
1979/05/09

Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12

Improvements To Optional Modification Of 5P4150 Nozzle Tester
1981/08/26

New Fuel Nozzle Test Sheet Available
1982/10/20

Bulged Capsule-Type Fuel Nozzles
1982/10/20

Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20

Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15

New Cylinder Heads, Fuel Nozzles And Fuel Nozzle Adapters Used
1984/10/24

New Tools Available To Service Fuel Injection Nozzles And Adapters
1985/01/16

New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles
1985/04/01

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced
1985/05/01

Check Fuel Injection Nozzles In Overheated Engines
1985/09/01

Gasket Leakage On Aftermarket Fuel Filters
1986/01/01

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01

Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles
1986/10/01

New Bleed Screw Used On 7000 Series Fuel Injection Nozzles
1989/03/01

Be Sure To Tighten Fuel Injection Line Clamps To The Correct Torque
1989/09/01

New Fuel Line Assemblies And Adapter Assembly Used
1992/02/01

5P7437 Adapter (Part Of 8T5301 Diesel Timing Adapter Group) Must Be Modified To Work On Current Fuel Lines.
1992/02/01

Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN)
1992/04/01

Improved 1R-0712 Fuel Filter Available{1261}
1994/03/01

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/01

Fuel Injection Nozzle Spray Orifice Plugging{1254}
1994/07/01

Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/23

New O-Ring Seals Used On "Through-Head-Adapter" And "Internal Fuel Lines" In Fuel Injection Lines Groups{1252}
1996/11/01

New Fuel Line Support Brackets Help Eliminate Vibration {1252}
1997/12/16

Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01

Needle Valve May Be Needed To Accurately Measure Engine Return Fuel Flow{1250,0782}
1999/04/01

Special Instruction

Installation of 9Y3499 Fuel Line Clamps Parts Kit{1252}
Installation of 9Y3499 Fuel Line Clamps Parts Kit{1252}

Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

7000 Series Nozzles{0782}
7000 Series Nozzles{0782}

Service Letter-NACD

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles

Specifications

Fuel Injection Lines
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Nozzle And Adapter (Earlier) (3406B)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Nozzle And Adapter (Later) (3406B)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Lines (3406)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Lines (Double Walled)
3400 GENERATOR SET ENGINE ATTACHMENTS

Service Letter-China

Service Letter-Asia

Service Letter-APD

Disassembly and Assembly

Fuel Injection Lines
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Filter And Base
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Line Adapters
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Nozzles And Adapters
3406B DIESEL ENGINE FOR GENERATOR SETS

Service Magazine

Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies{1254,0651}
1980/09/29

Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17

New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03

Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27

New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04

Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11

Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

New Valve Assembly And Seal Used In Fuel Transfer Pump{1256}
1984/05/14

New Cylinder Heads, Fuel Nozzles And Fuel Nozzle Adapters Used{1101,1106}
1984/10/29

Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14

New Tools Available To Service Fuel Injection Nozzles And Adapters {0706,1254}
1985/01/14

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced{1254}
1985/03/18

New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles{1254,1250}
1985/04/01

Extra Injection Nozzle Clamp Helps Prevent Injection Nozzle Damage{1252}
1985/07/15

Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings{1250,1264,1278,1287}
1985/11/11

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

Gasket Leakage On Aftermarket Fuel Filters{1261}
1985/12/16

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07

Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21

New Material Used For Disc In Valve Assemblies Of Fuel Transfer Pump Groups{1256}
1986/09/01

Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles{1254,1250}
1986/09/29

Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14

With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11

New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23

New Larger Capacity Water Separator Is Available{1250}
1979/03/12

Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23

Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

New Bleed Screw Used On 7000 Series Fuel Injection Nozzles{1254}
1989/03/06

Be Sure To Tighten Fuel Injection Line Clamps To The Correct Torque{1252}
1989/09/11

5P7437 Adapter (Part Of 8T5301 Diesel Timing Adapter Group) Must Be Modified To Work On Current Fuel Lines.{0782}
1992/02/03

New Fuel Line Assemblies And Adapter Assembly Used{1252}
1992/02/17

Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN){1254}
1992/04/20

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23

Be Sure To Correctly Tighten 1R-0712, 1R-0740, 1R-0749, 1R-0750, 1R-0751, 1R-0753, And 1R-0759 Fuel Filter Assemblies {1261}
1998/01/26

LINES GP-FUEL INJECTION

Engine News

Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20

Check Fuel Injection Nozzles In Overheated Engines
1985/09/01

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01

Be Sure To Tighten Fuel Injection Line Clamps To The Correct Torque
1989/09/01

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/01

Fuel Injection Nozzle Spray Orifice Plugging{1254}
1994/07/01

New O-Ring Seals Used On "Through-Head-Adapter" And "Internal Fuel Lines" In Fuel Injection Lines Groups{1252}
1996/11/01

New Fuel Line Support Brackets Help Eliminate Vibration {1252}
1997/12/16

Reannouncing the Appearance Change to Cat Reman Direct Injection Fuel Nozzles for Certain Commercial Engines {1250, 1251, 1290, 1713}
2013/10/17

Special Instruction

Installation of 9Y3499 Fuel Line Clamps Parts Kit{1252}
Installation of 9Y3499 Fuel Line Clamps Parts Kit{1252}

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

Service Letter-NACD

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles

Service Letter-China

Service Letter-Asia

Information Release Memo

APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS

Service Letter-APD

Service Magazine

Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies{1254,0651}
1980/09/29

Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17

New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03

Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27

New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04

Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11

Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22

New Cylinder Heads, Fuel Nozzles And Fuel Nozzle Adapters Used{1101,1106}
1984/10/29

New Tools Available To Service Fuel Injection Nozzles And Adapters {0706,1254}
1985/01/14

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced{1254}
1985/03/18

New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles{1254,1250}
1985/04/01

Extra Injection Nozzle Clamp Helps Prevent Injection Nozzle Damage{1252}
1985/07/15

Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07

Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21

Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles{1254,1250}
1986/09/29

Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14

With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23

Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

New Bleed Screw Used On 7000 Series Fuel Injection Nozzles{1254}
1989/03/06

Be Sure To Tighten Fuel Injection Line Clamps To The Correct Torque{1252}
1989/09/11

New Fuel Line Assemblies And Adapter Assembly Used{1252}
1992/02/17

Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN){1254}
1992/04/20

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23

Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14

LINES GP-FUEL RATIO CONTROL

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings{1250,1264,1278,1287}
1985/11/11

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

METER GP-SERVICE

Self-Powered Hour Meters Available{7480,7450}
1987/02/16

Polarity Connections And Use Of Service Meter Films When Service Meter Kits Are Installed{7480,7000}
1987/02/16

Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29

More Potting Material Now Used In 6N5906 Electric Service Meter{7480}
1979/11/26

MISCELLANEOUS INFORMATION

Engine News

Use New Adapter To Make Tests Of 9L6884 Nozzles
1979/05/09

Fuel Heaters Are Now Available For Field Installation
1980/01/09

Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12

Improvements To Optional Modification Of 5P4150 Nozzle Tester
1981/08/26

Explanation Of Differences In Timing Advance Information
1981/08/26

New EG3P Actuator Assemblies Available
1984/03/07

Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers
1986/03/01

Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01

Changes Have Been Made To 0T Microfiche (Fuel Setting And Related Information)
1986/07/01

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01

Fuel Dilution Troubleshooting Procedure
1987/01/01

Procedure To Check 7C2700 Voltage Control Module
1992/01/01

Fuel Injection Nozzle Spray Orifice Plugging{1254}
1994/07/01

New Guideline For Product Information, SEBF8340, " Fuel Systems Troubleshooting Guide For 3204, 3300, And 3400 Engines With New Scroll Fuel Systems (NSFS)" Available {0374,1250}
1998/06/01

Needle Valve May Be Needed To Accurately Measure Engine Return Fuel Flow{1250,0782}
1999/04/01

Special Instruction

Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}

Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}

Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}

Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}

Service Letter-NACD

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Product Support Program For The Calibration Of The Electronic Speed Switches On Certain 3406, 3408 And 3412 Industrial And Generator Set Engines
Product Support Program For The Calibration Of The Electronic Speed Switches On Certain 3406, 3408 And 3412 Industrial And Generator Set Engines

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Americas

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles

Service Letter-China

Service Letter-Asia

Service Letter-APD

Service Magazine

Fuel Heaters Are Now Available For Field Installation {1296}
1980/01/07

Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies{1254,0651}
1980/09/29

Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17

New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23

Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine{0651,0654,1250}
1982/03/22

Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur{1318,0375,0374,1280}
1982/05/03

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16

Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27

New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04

Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11

Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22

Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15

Service Information For Woodward Governors{0374,1264}
1983/09/26

Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07

Correct Wiring And Fuse Must Be Used For Correct Operation Of Shut-Off Solenoid Group{1259}
1984/01/30

New EG3P Actuator Assemblies Available{1289}
1984/02/27

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

Overvoltage Protection For Woodward 2301 Governor{1289}
1984/04/09

Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators{1265,1289}
1984/04/23

New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14

New Valve Assembly And Seal Used In Fuel Transfer Pump{1256}
1984/05/14

New Cylinder Heads, Fuel Nozzles And Fuel Nozzle Adapters Used{1101,1106}
1984/10/29

Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10

Bonnet Of Fuel Injection Pump Group Now Serviced Separately{1251,1250}
1984/12/10

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced{1254}
1985/03/18

New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles{1254,1250}
1985/04/01

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03

Orifice Fitting Or Snubber Can Help Stop Erratic Fuel Gauge Operation{7456}
1985/06/24

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Special Instruction Available To Salvage Governor Housing{1287}
1985/07/15

Eliminating Interference Between Governor Housing And Tachometer Drive{1264,7487}
1985/08/12

Location Of 6V5135 Setscrews In Fuel Pump Group{1250}
1985/08/12

Thread Lock Now Used On Timing Advance Bolts{1272}
1985/08/12

Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

Fuel Transfer Pump Improved{1256}
1985/10/14

Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28

Engine Information Plate Contains More Data; Use Of Performance Specifications{1250,7557}
1985/10/28

Check Fuel Injection Replacement Pump Installation{1251,1253,1257}
1985/10/28

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings{1250,1264,1278,1287}
1985/11/11

Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11

Faster Response Water Temperature Regulators; Service Simplified{1350,1355}
1985/11/25

New Fuel Ratio Control Group Used On Engines Equipped With New Scroll Fuel System{1278}
1985/11/25

Gasket Leakage On Aftermarket Fuel Filters{1261}
1985/12/16

Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13

Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10

Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07

Three Element Speed Switch Replaces Dual Element Speed Switch{7418,7411,7410,7421}
1986/04/21

Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05

FT Tooling Prints Available For Bushing Installation In Governor Housing{0600,1287}
1986/05/05

Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16

Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16

New Material Used For Disc In Valve Assemblies Of Fuel Transfer Pump Groups{1256}
1986/09/01

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22

Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles{1254,1250}
1986/09/29

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

Fuel Dilution Troubleshooting Procedure{1250}
1986/12/22

Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14

Diesel Fuel Recommendation Expanded{1280}
1977/02/14

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31

Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16

Improved Fuel Priming Pump Used{1258}
1987/04/20

Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems {0774,1250,1300,1350}
1987/05/11

New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters {1281,1250}
1987/09/28

Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11

Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25

Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25

Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16

Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16

New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04

Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18

New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23

Governor Actuator Now Installed With Shock Mounting{1286}
1988/08/22

Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29

High Sulfur Fuel Can Cause Severe Engine Wear And Internal Damage{1280}
1979/02/05

How To Extend The Service Life Of 1P5550 Fuel Cam Locking Tool Assembly{0654,1250}
1979/04/16

9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28

Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27

More Potting Material Now Used In 6N5906 Electric Service Meter{7480}
1979/11/26

Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

New Bleed Screw Used On 7000 Series Fuel Injection Nozzles{1254}
1989/03/06

Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings{1253}
1992/01/20

5P7437 Adapter (Part Of 8T5301 Diesel Timing Adapter Group) Must Be Modified To Work On Current Fuel Lines.{0782}
1992/02/03

New Fuel Line Assemblies And Adapter Assembly Used{1252}
1992/02/17

Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN){1254}
1992/04/20

New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25

Major Engine Component Changes{1201,1202,1205,1218,1219,1230,1253,1288,1331}
1992/09/07

Improved Jacket Water Heater Thermostat{1355}
1993/09/20

NOZZLE AS-FUEL VALVE

Engine News

Fuel Injection Nozzle Spray Orifice Plugging{1254}
1994/07/01

Special Instruction

Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

Technical Information Bulletin

Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles

Service Magazine

Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies{1254,0651}
1980/09/29

Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17

Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27

New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04

Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11

Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22

New Cylinder Heads, Fuel Nozzles And Fuel Nozzle Adapters Used{1101,1106}
1984/10/29

New Tools Available To Service Fuel Injection Nozzles And Adapters {0706,1254}
1985/01/14

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced{1254}
1985/03/18

Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07

Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14

With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11

New Bleed Screw Used On 7000 Series Fuel Injection Nozzles{1254}
1989/03/06

Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN){1254}
1992/04/20

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23

NOZZLE GP-UNIT INJECTOR

Engine News

Cat® Reman Announces the Availability of Additional Engine Components for Certain Engine Applications {1052, 1053, 108F, 1210, 1265, 1290, 1405, 1901, 5510}
2015/06/26

Special Instruction

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

Service Magazine

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23

PUMP GP-FUEL INJECTION

Engine News

Use New Adapter To Make Tests Of 9L6884 Nozzles
1979/05/09

Improvements To Optional Modification Of 5P4150 Nozzle Tester
1981/08/26

Explanation Of Differences In Timing Advance Information
1981/08/26

New Fuel Nozzle Test Sheet Available
1982/10/20

Bulged Capsule-Type Fuel Nozzles
1982/10/20

Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20

Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15

Service Information For Woodward Governors
1983/10/26

New Valve Lifter Assemblies Used In Valve Mechanism Groups
1983/11/30

Overvoltage Protection For Woodward 2301 Governor
1984/04/11

New Valve Assembly And Seal Used In Fuel Transfer Pump
1984/05/16

New Cylinder Heads, Fuel Nozzles And Fuel Nozzle Adapters Used
1984/10/24

Bonnet Of Fuel Injection Pump Group Now Serviced Separately
1984/12/12

Fill Oil Sump Before Installing Woodward Governor
1985/01/16

New Tools Available To Service Fuel Injection Nozzles And Adapters
1985/01/16

Over Fueling Spring No Longer Used In Governor
1985/03/01

New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles
1985/04/01

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced
1985/05/01

Thread Lock Now Used On Timing Advance Bolts
1985/08/01

Eliminating Interference Between Governor Housing And Tachometer Drive
1985/08/01

Location Of 6V5135 Setscrews In Fuel Pump Group
1985/08/01

Special Instruction Available To Salvage Governor Housing
1985/08/01

Check Fuel Injection Nozzles In Overheated Engines
1985/09/01

Fuel Transfer Pump Improved
1985/11/01

Check Fuel Injection Replacement Pump Installation
1985/11/01

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings
1985/12/01

Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01

Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01

FT Tooling Prints Available For Bushing Installation In Governor Housing
1986/05/01

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups
1986/06/01

Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01

New Material Used For Disc In Valve Assemblies In Fuel Transfer Pump Groups
1986/09/01

Indications Of Engine Overspeeding When Only One Cam Lobe/Lifter Has Failed
1986/10/01

Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles
1986/10/01

Improved Retaining Bushing In Fuel Injection Pump
1986/12/01

Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01

New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters
1987/10/01

Improved Valve Mechanism Cover Groups
1988/01/01

Governor Actuator Now Installed With Shock Mounting
1988/08/01

New Bleed Screw Used On 7000 Series Fuel Injection Nozzles
1989/03/01

Be Sure To Tighten Fuel Injection Line Clamps To The Correct Torque
1989/09/01

Governor Control Motor Polarity May Require A Change
1990/11/01

Corrections For Systems Operation, Troubleshooting, And Specifications For 2301 Electric Governors For Generator Set And Industrial Engines, SENR2928-01
1991/05/01

New Speed Setting Clutch Group For 3161 Woodward Governors
1991/06/01

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings
1991/10/01

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings
1992/01/01

Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN)
1992/04/01

Be Sure The Fuel Injection Pump Housing Is Compatible With 0R0715 And 0R2545 Remanufactured Short Blocks
1992/08/01

New Fuel Injection Pump Groups Have Larger Diameter Camshaft Bores, New Lifter Assembly, And Shorter Plunger And Barrel Assembly
1992/09/01

New Bonnet Used In Fuel Injection Pump Group
1993/06/01

Fuel Injection Pump Improvements{1251}
1994/02/01

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/01

Fuel Injection Nozzle Spray Orifice Plugging{1254}
1994/07/01

New Seals In Pump Fastener Group And Fuel Injection Pump Group Have Improved Heat Set Resistance {1251}
1994/09/01

Pressure Compensated Simple Governor (PSG Governor) Changes From Aluminum To Cast Iron Housing {1264}
1995/04/01

Fuel Injection Pump Barrel Sealing Face Reconditioning{1251}
1996/03/19

Woodward Control Assemblies Have Changed Part Numbers To Provide The CE Marking For Electromagnetic Compatibility (EMC) Directives{1264}
1996/05/09

Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/23

Fuel Injection Pump Bushings Have New Groove Adjacent To Load Ring {1251}
1996/11/01

New O-Ring Seals Used On "Through-Head-Adapter" And "Internal Fuel Lines" In Fuel Injection Lines Groups{1252}
1996/11/01

Improved Bushing O-Ring Seal Available For Injection Pump Groups{1251}
1997/03/01

Improvements Made To Remanufactured 0R-3008 Fuel Transfer Pump{1256}
1997/03/01

Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13

Troubleshooting Engines with Mechanical Unit Injection (MUI) {1000, 1254}
2006/01/02

The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
2007/08/20

Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01

Improved Manufacturing Processes Are Used for Remanufactured Fuel Injector Nozzles That Are Used in Certain Commercial Engines {1251, 1290}
2012/07/06

Reannouncing the Appearance Change to Cat Reman Direct Injection Fuel Nozzles for Certain Commercial Engines {1250, 1251, 1290, 1713}
2013/10/17

Cat® Reman Announces New Fuel Pump, Fuel Ratio Control, and Fuel Injector Options for Certain Engines {1251, 1278}
2014/09/05

Special Instruction

Use of 6V6070 Governor Adjusting Tool Group{1250}
Use of 6V6070 Governor Adjusting Tool Group{1250}

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Wiring Polarity on Woodward 2301 Governors{1289}
Wiring Polarity on Woodward 2301 Governors{1289}

Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}

3406 New Scroll Fuel System (NSFS) Camshaft Plugs{1110}
3406 New Scroll Fuel System (NSFS) Camshaft Plugs{1110}

Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}

Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}

Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}

Installation Of 4W5391 Preregulator Box Assembly{1289}
Installation Of 4W5391 Preregulator Box Assembly{1289}

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

7000 Series Nozzles{0782}
7000 Series Nozzles{0782}

Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}
Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}

Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}

Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}

Service Letter-NACD

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-CSARL

Service Letter-Americas

Technical Information Bulletin

Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles

Valve Bonnets with Insufficient Hardness
Valve Bonnets with Insufficient Hardness

Specifications

Fuel Injection Lines
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Nozzle And Adapter (Earlier) (3406B)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Nozzle And Adapter (Later) (3406B)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Pump (3406B)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Pump Housing (3406B)
3406 & 3406B GENERATOR SET ENGINE

Governor and Fuel Pump Drive Group (3406B)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Pump Housing (3406)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection (3406)
3406 & 3406B GENERATOR SET ENGINE

Automatic Timing Advance Unit
3406 & 3406B GENERATOR SET ENGINE

Governor and Fuel Pump Drive Gear (3406)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Lines (3406)
3406 & 3406B GENERATOR SET ENGINE

Fuel Injection Lines (Double Walled)
3400 GENERATOR SET ENGINE ATTACHMENTS

Information Release Memo

APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS

Disassembly and Assembly

Fuel Injection Lines
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Transfer Pump
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Pump Housing And Governor
3406B DIESEL ENGINE FOR GENERATOR SETS

Governor
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Pumps
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Pump Housing
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Line Adapters
3406B DIESEL ENGINE FOR GENERATOR SETS

Rocker Shaft Assemblies And Push Rods
3406B DIESEL ENGINE FOR GENERATOR SETS

Rocker Shaft Assemblies
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Nozzles And Adapters
3406B DIESEL ENGINE FOR GENERATOR SETS

Service Magazine

Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies{1254,0651}
1980/09/29

Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17

New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03

Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27

New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04

Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11

Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22

Service Information For Woodward Governors{0374,1264}
1983/09/26

Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14

New Valve Assembly And Seal Used In Fuel Transfer Pump{1256}
1984/05/14

New Cylinder Heads, Fuel Nozzles And Fuel Nozzle Adapters Used{1101,1106}
1984/10/29

Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10

Bonnet Of Fuel Injection Pump Group Now Serviced Separately{1251,1250}
1984/12/10

Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14

New Tools Available To Service Fuel Injection Nozzles And Adapters {0706,1254}
1985/01/14

Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04

Over Fueling Spring No Longer Used In Governor{1264,1250}
1985/02/04

Internal Seals In 7000 Series Fuel Injection Nozzles Cannot Be Replaced{1254}
1985/03/18

New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles{1254,1250}
1985/04/01

Extra Injection Nozzle Clamp Helps Prevent Injection Nozzle Damage{1252}
1985/07/15

Eliminating Interference Between Governor Housing And Tachometer Drive{1264,7487}
1985/08/12

Location Of 6V5135 Setscrews In Fuel Pump Group{1250}
1985/08/12

Thread Lock Now Used On Timing Advance Bolts{1272}
1985/08/12

Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02

Fuel Transfer Pump Improved{1256}
1985/10/14

Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28

Check Fuel Injection Replacement Pump Installation{1251,1253,1257}
1985/10/28

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings{1250,1264,1278,1287}
1985/11/11

Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11

Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10

Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10

Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02

Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09

Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16

Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16

New Material Used For Disc In Valve Assemblies Of Fuel Transfer Pump Groups{1256}
1986/09/01

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22

Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles{1254,1250}
1986/09/29

Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03

Improved Retaining Bushing In Fuel Injection Pump {1251,1250}
1986/12/01

New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17

Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14

With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31

New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters {1281,1250}
1987/09/28

Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11

Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25

Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25

Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16

New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04

Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18

Governor Actuator Now Installed With Shock Mounting{1286}
1988/08/22

Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23

9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28

Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02

Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

New Bleed Screw Used On 7000 Series Fuel Injection Nozzles{1254}
1989/03/06

Be Sure To Tighten Fuel Injection Line Clamps To The Correct Torque{1252}
1989/09/11

Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29

New Speed Setting Clutch Group For 3161 Woodward Governors{1265}
1991/05/20

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings{1253}
1991/09/30

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings{1253}
1992/01/20

Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN){1254}
1992/04/20

Be Sure The Fuel Injection Pump Housing Is Compatible With 0R0715 And 0R2545 Remanufactured Short Blocks{1201,1253}
1992/08/31

Major Engine Component Changes{1201,1202,1205,1218,1219,1230,1253,1288,1331}
1992/09/07

New Fuel Injection Pump Groups Have Larger Diameter Camshaft Bores, New Lifter Assembly, And Shorter Plunger And Barrel Assembly{1251,1253,1281,1292}
1992/09/21

New Bonnet Used In Fuel Injection Pump Group {1251}
1993/06/14

Camshaft Lobe Surface Finish Improved; Camshaft Drive Gear Installation Procedure {1209,1210,1212}
1993/09/13

Fuel Injection Pump Improvements{1251}
1994/02/07

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23

Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14

PUMP GP-FUEL PRIMING

Engine News

Location Of 6V5135 Setscrews In Fuel Pump Group
1985/08/01

Improved Fuel Priming Pump Used
1987/05/01

Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01

Special Instruction

Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System{1258}
Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System{1258}

Service Magazine

New Valve Assembly And Seal Used In Fuel Transfer Pump{1256}
1984/05/14

Fuel Transfer Pump Improved{1256}
1985/10/14

Gasket Leakage On Aftermarket Fuel Filters{1261}
1985/12/16

New Material Used For Disc In Valve Assemblies Of Fuel Transfer Pump Groups{1256}
1986/09/01

Improved Fuel Priming Pump Used{1258}
1987/04/20

New Larger Capacity Water Separator Is Available{1250}
1979/03/12

Be Sure To Correctly Tighten 1R-0712, 1R-0740, 1R-0749, 1R-0750, 1R-0751, 1R-0753, And 1R-0759 Fuel Filter Assemblies {1261}
1998/01/26

Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
2004/03/29

PUMP GP-FUEL TRANSFER

Engine News

Explanation Of Differences In Timing Advance Information
1981/08/26

Service Information For Woodward Governors
1983/10/26

Overvoltage Protection For Woodward 2301 Governor
1984/04/11

New Valve Assembly And Seal Used In Fuel Transfer Pump
1984/05/16

Bonnet Of Fuel Injection Pump Group Now Serviced Separately
1984/12/12

Fill Oil Sump Before Installing Woodward Governor
1985/01/16

Over Fueling Spring No Longer Used In Governor
1985/03/01

Thread Lock Now Used On Timing Advance Bolts
1985/08/01

Eliminating Interference Between Governor Housing And Tachometer Drive
1985/08/01

Location Of 6V5135 Setscrews In Fuel Pump Group
1985/08/01

Special Instruction Available To Salvage Governor Housing
1985/08/01

Fuel Transfer Pump Improved
1985/11/01

Check Fuel Injection Replacement Pump Installation
1985/11/01

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings
1985/12/01

Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01

Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01

FT Tooling Prints Available For Bushing Installation In Governor Housing
1986/05/01

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups
1986/06/01

Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01

New Material Used For Disc In Valve Assemblies In Fuel Transfer Pump Groups
1986/09/01

Improved Retaining Bushing In Fuel Injection Pump
1986/12/01

Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01

New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters
1987/10/01

Governor Actuator Now Installed With Shock Mounting
1988/08/01

Governor Control Motor Polarity May Require A Change
1990/11/01

Corrections For Systems Operation, Troubleshooting, And Specifications For 2301 Electric Governors For Generator Set And Industrial Engines, SENR2928-01
1991/05/01

New Speed Setting Clutch Group For 3161 Woodward Governors
1991/06/01

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings
1991/10/01

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings
1992/01/01

Be Sure The Fuel Injection Pump Housing Is Compatible With 0R0715 And 0R2545 Remanufactured Short Blocks
1992/08/01

New Fuel Injection Pump Groups Have Larger Diameter Camshaft Bores, New Lifter Assembly, And Shorter Plunger And Barrel Assembly
1992/09/01

New Bonnet Used In Fuel Injection Pump Group
1993/06/01

Fuel Injection Pump Improvements{1251}
1994/02/01

New Seals In Pump Fastener Group And Fuel Injection Pump Group Have Improved Heat Set Resistance {1251}
1994/09/01

Pressure Compensated Simple Governor (PSG Governor) Changes From Aluminum To Cast Iron Housing {1264}
1995/04/01

Woodward Control Assemblies Have Changed Part Numbers To Provide The CE Marking For Electromagnetic Compatibility (EMC) Directives{1264}
1996/05/09

Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/23

Fuel Injection Pump Bushings Have New Groove Adjacent To Load Ring {1251}
1996/11/01

Improved Bushing O-Ring Seal Available For Injection Pump Groups{1251}
1997/03/01

Improvements Made To Remanufactured 0R-3008 Fuel Transfer Pump{1256}
1997/03/01

Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13

Special Instruction

Use of 6V6070 Governor Adjusting Tool Group{1250}
Use of 6V6070 Governor Adjusting Tool Group{1250}

"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}

Wiring Polarity on Woodward 2301 Governors{1289}
Wiring Polarity on Woodward 2301 Governors{1289}

Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}

Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}

Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}

Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}

Installation Of 4W5391 Preregulator Box Assembly{1289}
Installation Of 4W5391 Preregulator Box Assembly{1289}

Service Letter-NACD

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-CSARL

Service Letter-Americas

Specifications

Fuel Transfer Pump (3406B)
3406 & 3406B GENERATOR SET ENGINE

Fuel Transfer Pump (3406)
3406 & 3406B GENERATOR SET ENGINE

Fuel Transfer Pump And Tachometer Drive (3406)
3406 & 3406B GENERATOR SET ENGINE

Tool Operating Manual

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

Reuse And Salvage Guidelines

Reuse and Salvage of New Scroll Fuel Systems (NSFS) for 3200, 3300, & 3400 Engines {1250, 1256}
Reuse and Salvage of New Scroll Fuel Systems (NSFS) for 3200, 3300, & 3400 Engines {1250, 1256}

Disassembly and Assembly

Fuel Transfer Pump
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Pump Housing And Governor
3406B DIESEL ENGINE FOR GENERATOR SETS

Governor
3406B DIESEL ENGINE FOR GENERATOR SETS

Fuel Injection Pumps
3406B DIESEL ENGINE FOR GENERATOR SETS

Service Magazine

Service Information For Woodward Governors{0374,1264}
1983/09/26

Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14

New Valve Assembly And Seal Used In Fuel Transfer Pump{1256}
1984/05/14

Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10

Bonnet Of Fuel Injection Pump Group Now Serviced Separately{1251,1250}
1984/12/10

Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04

Over Fueling Spring No Longer Used In Governor{1264,1250}
1985/02/04

Eliminating Interference Between Governor Housing And Tachometer Drive{1264,7487}
1985/08/12

Location Of 6V5135 Setscrews In Fuel Pump Group{1250}
1985/08/12

Fuel Transfer Pump Improved{1256}
1985/10/14

Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28

Check Fuel Injection Replacement Pump Installation{1251,1253,1257}
1985/10/28

Special Bolts Help Prevent Unauthorized Modification Of Fuel System And Governor Settings{1250,1264,1278,1287}
1985/11/11

Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11

Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10

Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02

Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09

Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16

New Material Used For Disc In Valve Assemblies Of Fuel Transfer Pump Groups{1256}
1986/09/01

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22

Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03

Improved Retaining Bushing In Fuel Injection Pump {1251,1250}
1986/12/01

Improved Fuel Priming Pump Used{1258}
1987/04/20

New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters {1281,1250}
1987/09/28

Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25

Governor Actuator Now Installed With Shock Mounting{1286}
1988/08/22

9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28

Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06

Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29

Use 7E5888 Fuel Injection Pump Housing As A Service Replacement For Pre 1991 Fuel Injection Pump Housings{1253}
1991/09/30

Be Sure The Fuel Injection Pump Housing Is Compatible With 0R0715 And 0R2545 Remanufactured Short Blocks{1201,1253}
1992/08/31

Major Engine Component Changes{1201,1202,1205,1218,1219,1230,1253,1288,1331}
1992/09/07

New Fuel Injection Pump Groups Have Larger Diameter Camshaft Bores, New Lifter Assembly, And Shorter Plunger And Barrel Assembly{1251,1253,1281,1292}
1992/09/21

New Bonnet Used In Fuel Injection Pump Group {1251}
1993/06/14

Fuel Injection Pump Improvements{1251}
1994/02/07

PUMP GP-REFUELING

Special Instruction

Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}

RACK SETTING GP

Service Magazine

Fuel Setting And Air Fuel Ratio Control Adjustment Tools For 3406B Engines{0650,1264,1257,1278}
1984/03/26

Check Fuel Injection Replacement Pump Installation{1251,1253,1257}
1985/10/28

Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10

Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22

Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03

Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16

Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10

REGULATOR GP-GAS PRESSURE

Faster Response Water Temperature Regulators; Service Simplified{1350,1355}
1985/11/25

Improved Jacket Water Heater Thermostat{1355}
1993/09/20

SEPARATOR GP-WATER

New Larger Capacity Water Separator Is Available{1250}
1979/03/12

Be Sure To Correctly Tighten 1R-0712, 1R-0740, 1R-0749, 1R-0750, 1R-0751, 1R-0753, And 1R-0759 Fuel Filter Assemblies {1261}
1998/01/26

SHUTOFF GP

Engine News

Correct Wiring And Fuse Must Be Used For Correct Operation Of Shut-Off Solenoid Group
1984/02/22

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups
1986/06/01

Governor Control Motor Polarity May Require A Change
1990/11/01

Improved Air Pipe And New Valve Assembly Used In Air Shut-Off Group
1992/01/01

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13

Special Instruction

Installation of 7C7466 Solenoid Repair Kit{1259}
Installation of 7C7466 Solenoid Repair Kit{1259}

Installation Of 4W1979 Shut-Off Group{1704}
Installation Of 4W1979 Shut-Off Group{1704}

Service Letter-NACD

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Americas

The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines
The Governor Output Lever Needs To Be Repositioned On Certain 3406B Generator Set Engines

Service Letter-Truck/Ag/Marine

Specifications

Governor Controls
3400 GENERATOR SET ENGINE ATTACHMENTS

Service Letter-China

Service Letter-Asia

Service Letter-APD

Service Magazine

Correct Wiring And Fuse Must Be Used For Correct Operation Of Shut-Off Solenoid Group{1259}
1984/01/30

Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators{1265,1289}
1984/04/23

Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04

Three Element Speed Switch Replaces Dual Element Speed Switch{7418,7411,7410,7421}
1986/04/21

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05

More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29

SHUTOFF GP-MANUAL

Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05

SUPPLY GP-FUEL

Service Letter-NACD

Service Magazine

Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21

New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23

Truck sale:

USD $25,000

1990 CAT 3406B

Power Generation Enterprises Inc.
North Hollywood, California

USD $22,000

1991 CAT 3406B

Ransome CAT
Bensalem, Pennsylvania

USD $35,000

1989 CAT 3406B

Worldwide Power Products LLC
Houston, Texas

USD $29,000

1988 CAT 3406B

Ransome CAT
Bensalem, Pennsylvania

$29,000 USD

CATERPILLAR 3406B 1988
- MARINE - PROPULSION
RANSOME ENGINE POWER
United States