AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

1W-6539 PUMP GP-FUEL INJECTION S/N 63Z590-22741 PART OF 8N-2525 PUMP GP-GOV & FUEL INJ 3306 TRUCK ENGINE


FUEL SYSTEM
PUMP GP-FUEL INJECTION
PUMP GP-FUEL PRIMING

TRUCK ENGINE 3306 TRUCK ENGINE 63Z
 3306 Truck Engine 63Z00001-22741 SEBP1476 3306 63Z   (1981)

FUEL SYSTEM

PUMP GP-FUEL INJECTION
PROTECTION GP-FUEL SYSTEM
9Y-0183 PROTECTION GP-FUEL SYSTEM
PUMP GP-FUEL INJECTION
1W-6539 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
1W-6539 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6I-2829 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6I-2830 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6I-2831 PUMP GP-FUEL INJECTION
 

#SEBP14760630
 

1W-6539: PUMP GP-FUEL INJECTION

1W-6539 PUMP GP-FUEL INJECTION
S/N 63Z590-22741
PART OF 8N-2525 PUMP GP-GOV & FUEL INJ
i00121989 SEBP1476
1W6539 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7W-1927 [1] RING-RETAINING  
2. 8N-1415 [1] SPRING-CHECK  
3. 1W-9171 [1] BONNET-VALVE  
4. 1W-6987 [1] VALVE AS-CHECK (FUEL)  
5. 1W-6541 [1] PLUNGER AS  
6. 7N-1067 [1] SPRING-LIFTER  
7. 7W-2808 [1] WASHER-RETAINING  
8. 7C-5278 C [1] BOLT-PLUNGER GEAR (FUEL PUMP)(12.1MM LG)  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP14760631
 

6I-2829: PUMP GP-FUEL INJECTION

6I-2829 PUMP GP-FUEL INJECTION
S/N 63Z19290-22741
PART OF 7E-9349, 7E-9350 PUMP GP-GOV & FUEL INJ
i00395213 SEBP1476
6I2829 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9S-4180 [2] PLUG  
2. 4J-7533 [2] SEAL-O-RING  
3. 1W-3286 [1] RACK-REGULATOR  
4. 7W-5928 Y [6] PUMP GP-FUEL INJECTION  
5. 8N-5117 [6] BUSHING-TERMINAL  
6. 114-8718 [6] SEAL-O-RING  
7. 4W-6869 [6] SPACER (27X32.54X5.049-MM THK)  
8. 150-3724 [1] GASKET  
9. 7N-8421 [1] RING-RETAINING  
10. 8N-2487 [1] WASHER-THRUST  
11. 4P-9832 [6] LIFTER AS  
12. 0S-1615 [4] BOLT (1/4-20X0.75-IN)  
13. 7N-1047 [1] COVER-TIMING  
14. 6I-2815 [1] CAMSHAFT AS  
  6I-2838 [1] CAMSHAFT-FUEL PUMP  
15. 8N-2510 [1] SHAFT-WEIGHT CARRIER  
16. 7N-7264 [4] WEIGHT-GOVERNOR  
17. 9Y-7037 [4] BOLT (1/4-20X1.25-IN)  
18. 1S-5440 [4] DOWEL  
19. 7E-3986 [1] CARRIER-WEIGHT  
20. 7N-7166 [2] RACE-THRUST BEARING  
21. 7L-3326 [1] BEARING-THRUST  
22. 4N-9019 [1] DOWEL  
23. 4P-9840 [1] HOUSING AS  
24. 1W-3285 [1] BEARING-RACK  
25. 1S-1953 [1] BEARING-RACK  
26. 6I-0979 [6] DOWEL  
27. 7N-7970 [1] BUSHING  
28. 4P-9828 [1] BUSHING  
29. 4P-8480 [6] PIN-PUMP GUIDE  
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP14760632
 

6I-2830: PUMP GP-FUEL INJECTION

6I-2830 PUMP GP-FUEL INJECTION
PART OF 7C-7606 PUMP GP-GOV & FUEL INJ
AN ATTACHMENT
i00395237 SEBP1476
6I2830 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9S-4180 [2] PLUG  
  4J-7533 [2] SEAL-O-RING  
2. 1W-3286 [1] RACK-REGULATOR  
3. 0S-1615 [4] BOLT (1/4-20X0.75-IN)  
4. 7W-5928 Y [6] PUMP GP-FUEL INJECTION  
5. 8N-5117 [6] BUSHING-TERMINAL  
6. 114-8718 [6] SEAL-O-RING  
7. 4W-6869 [6] SPACER (27X32.54X5.049-MM THK)  
8. 7N-1047 [1] COVER-TIMING  
  150-3724 [1] GASKET  
9. 7N-8421 [1] RING-RETAINING  
10. 8N-2487 [1] WASHER-THRUST  
11. 4P-9832 [6] LIFTER AS  
12. 4P-9840 [1] HOUSING AS  
13. 1S-1953 [1] BEARING-RACK  
14. 1W-3285 [1] BEARING-RACK  
15. 4P-8480 [6] PIN-PUMP GUIDE  
16. 6I-0979 [6] DOWEL  
17. 4P-9828 [1] BUSHING  
18. 7N-7970 [1] BUSHING  
19. 4P-9020 [1] CAMSHAFT AS  
  6I-2839 [1] CAMSHAFT-FUEL PUMP  
20. 7N-7264 [4] WEIGHT-GOVERNOR  
21. 9Y-7037 [4] BOLT (1/4-20X1.25-IN)  
22. 1S-5440 [4] DOWEL  
23. 4N-9019 [1] DOWEL  
24. 7E-3986 [1] CARRIER-WEIGHT  
25. 7L-3326 [1] BEARING-THRUST  
26. 8N-2510 [1] SHAFT-WEIGHT CARRIER  
27. 7N-7166 [2] RACE-THRUST BEARING  
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP14760633
 

6I-2831: PUMP GP-FUEL INJECTION

6I-2831 PUMP GP-FUEL INJECTION
S/N 63Z19284-22741
PART OF 7C-0496, 7W-5931 PUMP GP-GOV & FUEL INJ
ALSO AN ATTACHMENT
i00157221 SEBP1476
6I2831 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9S-4180 [2] PLUG  
  4J-7533 [2] SEAL-O-RING  
2. 1W-3286 [1] RACK-REGULATOR  
3. 0S-1615 [4] BOLT (1/4-20X0.75-IN)  
4. 7W-5928 Y [6] PUMP GP-FUEL INJECTION  
5. 8N-5117 [6] BUSHING-TERMINAL  
6. 114-8718 [6] SEAL-O-RING  
7. 4W-6869 [6] SPACER (27X32.54X5.049-MM THK)  
8. 7N-1047 [1] COVER-TIMING  
  150-3724 [1] GASKET  
9. 7N-8421 [1] RING-RETAINING  
10. 8N-2487 [1] WASHER-THRUST  
11. 4P-9832 [6] LIFTER AS  
12. 4P-9840 [1] HOUSING AS  
13. 1S-1953 [1] BEARING-RACK (REAR)  
14. 1W-3285 [1] BEARING-RACK (FRONT)  
15. 4P-8480 [6] PIN-PUMP GUIDE  
16. 6I-0979 [6] DOWEL  
17. 4P-9828 [1] BUSHING  
18. 7N-7970 [1] BUSHING  
19. 4P-9027 [1] CAMSHAFT AS  
20. 7N-7264 [4] WEIGHT-GOVERNOR  
21. 9Y-7037 [4] BOLT (1/4-20X1.25-IN)  
22. 1S-5440 [4] DOWEL (DIM 4.755MM)  
23. 4N-9019 [1] DOWEL (DIM 3.175MM)  
24. 7E-3986 [1] CARRIER-WEIGHT  
25. 7L-3326 [1] BEARING-THRUST  
26. 8N-2510 [1] SHAFT-WEIGHT CARRIER  
27. 7N-7166 [2] RACE-THRUST BEARING  
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP14760634
 

7C-1916: PUMP GP-FUEL INJECTION

7C-1916 PUMP GP-FUEL INJECTION
S/N 63Z3057-22741
PART OF 7C-1917, 7C-7606 PUMP GP-GOV & FUEL INJ
ALSO AN ATTACHMENT
i00402085 SEBP1476
7C1916 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9S-4180 [2] PLUG  
  4J-7533 [2] SEAL-O-RING  
2. 1W-3286 [1] RACK-REGULATOR  
3. 1W-3487 Y [1] HOUSING GP-FUEL PUMP  
4. 7W-5928 Y [6] PUMP GP-FUEL INJECTION  
5. 8N-5117 [6] BUSHING-TERMINAL  
6. 7E-4846 [6] SEAL-O-RING  
7. 4W-6869 [6] SPACER (27X32.54X5.049-MM THK)  
8. 7N-1046 [1] GASKET-COVER  
9. 7N-8421 [1] RING-RETAINING  
10. 8N-2487 [1] WASHER-THRUST  
11. 8N-2489 [6] LIFTER AS  
12. 0S-1615 [4] BOLT (1/4-20X0.75-IN)  
13. 7N-1047 [1] COVER-TIMING  
14. 7C-1915 [1] CAMSHAFT AS  
  7C-1914 [1] CAMSHAFT AS  
15. 8N-2510 [1] SHAFT-WEIGHT CARRIER  
  4N-9019 [1] DOWEL  
16. 7N-7265 [1] SHIELD-WEIGHT CARRIER  
  7N-7264 [4] WEIGHT-GOVERNOR  
  9Y-7037 [4] BOLT (1/4-20X1.25-IN)  
  1S-5440 [4] DOWEL  
17. 8N-2511 [1] CARRIER-WEIGHT  
18. 7N-7166 [2] RACE-THRUST BEARING  
  7L-3326 [1] BEARING-THRUST  
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP14760635
 

7C-3994: PUMP GP-FUEL INJECTION

7C-3994 PUMP GP-FUEL INJECTION
S/N 63Z3631-22741
PART OF 4P-5891, 7C-3993, 7C-7260, 7E-9349, 7E-9350 PUMP GP-GOV & FUEL INJ
ALSO AN ATTACHMENT
i00406187 SEBP1476
7C3994 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9S-4180 [2] PLUG  
  4J-7533 [2] SEAL-O-RING  
2. 1W-3286 [1] RACK-REGULATOR  
3. 1W-3487 Y [1] HOUSING GP-FUEL PUMP  
4. 7W-5928 Y [6] PUMP GP-FUEL INJECTION  
5. 8N-5117 [6] BUSHING-TERMINAL  
6. 3D-2992 [6] SEAL  
7. 4W-6869 [6] SPACER (27X32.54X5.049-MM THK)  
8. 7N-1046 [1] GASKET-COVER  
9. 7N-8421 [1] RING-RETAINING  
10. 8N-2487 [1] WASHER-THRUST  
11. 8N-2489 [6] LIFTER AS  
12. 0S-1615 [4] BOLT (1/4-20X0.75-IN)  
13. 7N-1047 [1] COVER-TIMING  
14. 7C-3995 [1] CAMSHAFT AS  
  7C-3996 [1] CAMSHAFT-FUEL PUMP  
15. 8N-2510 [1] SHAFT-WEIGHT CARRIER  
  4N-9019 [1] DOWEL  
16. 7N-7265 [1] SHIELD-WEIGHT CARRIER  
  7N-7264 [4] WEIGHT-GOVERNOR  
  9Y-7037 [4] BOLT (1/4-20X1.25-IN)  
  1S-5440 [4] DOWEL  
17. 8N-2511 [1] CARRIER-WEIGHT  
18. 7N-7166 [2] RACE-THRUST BEARING  
  7L-3326 [1] BEARING-THRUST  
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP14760636
 

7C-3994: PUMP GP-FUEL INJECTION

7C-3994 PUMP GP-FUEL INJECTION
S/N 63Z19290-22741
PART OF 7E-9350 PUMP GP-GOV & FUEL INJ
i00406191 SEBP1476
7C3994 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9S-4180 [2] PLUG  
2. 4J-7533 [2] SEAL-O-RING  
3. 1W-3286 [1] RACK-REGULATOR  
4. 7W-5928 Y [6] PUMP GP-FUEL INJECTION  
5. 8N-5117 [6] BUSHING-TERMINAL  
6. 114-8718 C [6] SEAL-O-RING  
7. 4W-6869 [6] SPACER (27X32.54X5.049-MM THK)  
8. 150-3724 [1] GASKET  
9. 7N-8421 [1] RING-RETAINING  
10. 8N-2487 [1] WASHER-THRUST  
11. 4P-9832 C [6] LIFTER AS  
12. 0S-1615 [4] BOLT (1/4-20X0.75-IN)  
13. 7N-1047 [1] COVER-TIMING  
14. 7C-3995 [1] CAMSHAFT AS  
  7C-3996 [1] CAMSHAFT-FUEL PUMP  
15. 8N-2510 [1] SHAFT-WEIGHT CARRIER  
  4N-9019 [1] DOWEL  
16. 7N-7265 [1] SHIELD-WEIGHT CARRIER  
  7N-7264 [4] WEIGHT-GOVERNOR  
  9Y-7037 [4] BOLT (1/4-20X1.25-IN)  
  1S-5440 [4] DOWEL  
17. 8N-2511 [1] CARRIER-WEIGHT  
18. 7N-7166 [2] RACE-THRUST BEARING  
  7L-3326 [1] BEARING-THRUST  
19. 6I-2987 C [1] HOUSING AS-PUMP  
20. 1S-1953 [1] BEARING-RACK  
21. 1W-3285 [1] BEARING-RACK  
22. 4P-8480 [6] PIN-PUMP GUIDE  
23. 6I-0979 [6] DOWEL  
24. 6I-1631 [1] BUSHING  
25. 7N-7970 [1] BUSHING  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP14760637
 

7W-5928: PUMP GP-FUEL INJECTION

7W-5928 PUMP GP-FUEL INJECTION
S/N 63Z2359-22741
PART OF 6I-2829, 6I-2830, 6I-2831, 7C-1916, 7C-3994 PUMP GP-FUEL INJECTION, 7W-5932 PUMP GP-GOV & FUEL INJ
OPTIONAL FIELD REPLACEMENT ORDER 432-8277 PUMP GP-FUEL INJECTION
ALSO AN ATTACHMENT
i00122409 SEBP1476
7W5928 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7W-1927 [1] RING-RETAINING  
2. 8N-1415 [1] SPRING-CHECK  
3. 1W-9171 [1] BONNET-VALVE  
4. 1W-6987 [1] VALVE AS-CHECK (FUEL INJECTION PUMP)  
5. 7W-5929 [1] PLUNGER & BARREL AS (FUEL PUMP)  
6. 7C-5278 C [1] BOLT-PLUNGER GEAR (FUEL PUMP)  
7. 7N-1066 C [1] WASHER-RETAINING  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP14760638
 

8N-2517: PUMP GP-FUEL INJECTION

8N-2517 PUMP GP-FUEL INJECTION
S/N 63Z1-589
PART OF 8N-2525 PUMP GP-GOV & FUEL INJ
i00193832 SEBP1476
8N2517 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1M-3506 [1] RING-RETAINING  
2. 8N-1415 [1] SPRING-CHECK  
3. 8N-2516 [1] BONNET-VALVE  
4. 8N-1414 [1] CHECK AS-PUMP  
5. 8N-9130 [1] PLUNGER AS  
6. 7N-1067 [1] SPRING-LIFTER  
7. 7N-1415 [1] WASHER-RETAINING  
 

#SEBP14760639
 

2W-1811: PUMP GP-FUEL PRIMING

2W-1811 PUMP GP-FUEL PRIMING
S/N 63Z1-1665
i00358207 SEBP1476
2W1811 PUMP GP-FUEL PRIMING Parts scheme
  For full view, you need register

Parts for your 3306 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1W-4999 [1] PUMP AS-FUEL PRIMING  
  1P-0436 [1] GASKET (FUEL PRIMING PUMP)  
2. 032-1268 [1] CONNECTOR (90-DEG)  
3. 0T-0065 [1] BOLT (3/8-16X3.5-IN)  
  0L-1351 [1] BOLT (3/8-16X0.875-IN)  
  5M-2894 [2] WASHER-HARD (10.2X18.5X2.5-MM THK)  
4. 2W-1809 [1] BRACKET AS-PUMP  
5. 5R-3564 [1] BLOCK  
6. 1D-4533 [1] BOLT (1/4-20X2.25-IN)  
  1B-4330 [1] NUT (1/4-20-THD)  
  5P-0537 [2] WASHER-HARD (7.2X14.5X2-MM THK)  
7. 1D-4538 [1] BOLT (5/16-18X2.25-IN)  
  1D-4716 [1] NUT-FULL (5/16-18-THD)  
  9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
 

Information:

Truck Engine News
FT1585 Plate Can Be Fabricated For Governor Spring Guide Replacement
1981/05/12
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/03/31
Do Not Use A Wire Brush On Fuel Nozzles
1982/09/29
New Torque Specification For Fuel Injection Pump Bushing
1982/09/29
New Fuel Nozzle Test Sheet Available
1982/10/27
Bulged Capsule-type Fuel Nozzles
1982/10/27
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/08
6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier
1982/12/08
New Gasket And Cover Used On Governors
1983/05/18
Governor Flyweight Shield No Longer Used In New Scroll Fuel Systems
1985/01/01
Over Fueling Spring No Longer Used In Governor
1985/02/01
New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles
1985/04/01
Check Fuel Injection Nozzles In Overheated Engines
1985/09/01
Fuel Transfer Pump Improved
1985/10/01
Bolt Removed From Governor And Fuel Injection Pump Group
1985/12/01
New 8T2998 Lubricant Available
1986/02/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Bleed Screw Washer (seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
New Material Used For Disc In Valve Assemblies In Fuel Transfer Pump Groups
1986/08/01
Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles
1986/10/01
Seals In Variable Timing Advance Available For Parts Service
1988/07/01
New Bleed Screw Used On 7000 Series Fuel Injection Nozzles
1989/03/01
New Gaskets Help Prevent Leaks From Fuel System Governors{1264}
1991/12/01
Identification Of Remanufactured Direct Injection Fuel Nozzles (DlFN)
1992/04/01
New Fuel Pump Drive Idler Gear Assembly And Shaft Used In Front Timing Gear Groups
1993/06/01
Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles {1254}
1994/05/31
Improved Fuel Pump Bonnet Seal Has Better Heat Resistance{1251}
1994/09/01
Tamper Resistant Plugs And Tamper Resistant Bolts Used To Prevent Changes To Air Fuel Ratio Control (AFRC) Setting{1278,1287}
1996/01/23
Governor Spring Guide Press Depth{1287,1284}
1996/01/23
Governor Control Cover Assembly Includes New Seal And Improved Cover{1264}
1997/07/01
Do Not Reuse the Hold Down Bolts for the Fuel Injector {1290}
2006/06/01
The Edge Filter Is Now Removed from Fuel Nozzles {1254, 1290}
2007/08/01
Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Do not Use the 1U-6661 Pop Tester Gp to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Improved Manufacturing Processes Are Used for Remanufactured Fuel Injector Nozzles That Are Used in Certain On-Highway Truck Engines {1251, 1290}
2012/07/09
Reannouncing the Appearance Change to Cat Reman Direct Injection Fuel Nozzles for Certain On-Highway Truck Engines {1250, 1251, 1290, 1713}
2013/10/29
Engine News
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time
1978/07/05
Calibration Fluid for Fuel Nozzle Test Equipment Is Available {0782, 1251, 1254, 1290, 1713}
2008/11/17
Special Instruction
Use Of 6V4095 Or 6V4096 Pump And Governor Tool Groups{650, 1250}
Use Of 6V4095 Or 6V4096 Pump And Governor Tool Groups{650, 1250}
Use of 6V6070 Governor Adjusting Tool Group{1250}
Use of 6V6070 Governor Adjusting Tool Group{1250}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Wiring Polarity on Woodward 2301 Governors{1289}
Wiring Polarity on Woodward 2301 Governors{1289}
Check Assembled Dimension for Rack Lever Travel{1264, 1250}
Check Assembled Dimension for Rack Lever Travel{1264, 1250}
Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Installation Of Sleeve Metering Fuel Injection Pump And Governor Service Groups{1286}
Installation Of Sleeve Metering Fuel Injection Pump And Governor Service Groups{1286}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
7000 Series Nozzles{0782}
7000 Series Nozzles{0782}
Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}
Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Service Letter-NACD
The Governor Rack Servo Cylinder Assembly Needs To Be Replaced On Certain 3306B And 3406B Truck Engines
The Governor Rack Servo Cylinder Assembly Needs To Be Replaced On Certain 3306B And 3406B Truck Engines
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Truck/Ag/Marine
Technical Information Bulletin
3300 Engine Timing Measurement For Reduced Emissions And Improved Engine Performance/Life
3300 Engine Timing Measurement For Reduced Emissions And Improved Engine Performance/Life
Specifications
Fuel Injection<BR> Injection Timing Before Top Center (BTC)
3306B DIESEL TRUCK ENGINE
Fuel Injection Pump
3306B DIESEL TRUCK ENGINE
Fuel Injection Pump Housing
3306B DIESEL TRUCK ENGINE
Governor
3306B DIESEL TRUCK ENGINE
Automatic Timing Advance
3306B DIESEL TRUCK ENGINE
Service Letter-China
The Governor Rack Servo Cylinder Assembly Needs To Be Replaced On Certain 3306B And 3406B Truck Engines
The Governor Rack Servo Cylinder Assembly Needs To Be Replaced On Certain 3306B And 3406B Truck Engines
Service Letter-Asia
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Service Letter-APD
The Governor Rack Servo Cylinder Assembly Needs To Be Replaced On Certain 3306B And 3406B Truck Engines
The Governor Rack Servo Cylinder Assembly Needs To Be Replaced On Certain 3306B And 3406B Truck Engines
Disassembly and Assembly
Fuel Injection Nozzles
3306B DIESEL TRUCK ENGINE
Governor
3306B DIESEL TRUCK ENGINE
Fuel Injection Pumps
3306B DIESEL TRUCK ENGINE
Fuel Injection Pump Housing
3306B DIESEL TRUCK ENGINE
Fuel Ratio Control
3306B DIESEL TRUCK ENGINE
Fuel Transfer Pump
3306B DIESEL TRUCK ENGINE
Cylinder Liners
3306B DIESEL TRUCK ENGINE
Service Magazine
New Fuel Injection Nozzle Assembly Used{1254}
1980/01/21
6V3129 Nozzle Puller Group And FT1533 Nozzle Assembly Adapter Can Be Used To Remove Fuel Nozzles{0621,1254}
1981/02/02
FT1585 Plate Can Be Fabricated For Governor Spring Guide Replacement{0626}
1981/04/13
Remove Direct Injection Fuel Nozzles With 6V4061 And 6V4054 Nozzle Pullers{0621}
1981/05/18
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
New Torque Specification For Bushing{0374,1253,1251}
1982/01/18
New 6V4818 Driver Available To Install Rack Bearings In Fuel Injection Pump Housings{0622}
1982/02/08
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
New Torque Specification For Fuel Injection Pump Bushing{1251,1253}
1982/08/09
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Tool Makes Installation Of Carbon Stop Seals Easier{0622,1254}
1982/10/04
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier{1206,1272,0614}
1982/11/08
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
New Gasket And Cover Used On Governors{1264}
1983/04/25
New Fuel Ratio Control Group Has Improved Diaphragm{1278,1257,1251}
1983/08/15
Remanufactured Fuel Pump And Governor Groups{1251,1264}
1983/10/17
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Fuel System Manual Bleed Valve Removed; Drain Lines Group Added{1251,1253,1286}
1984/02/13
Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
New Compression Washers (Gas Seals) Used On 7000 Series Fuel Injection Nozzles{1254,1250}
1985/04/01
Higher Torque Can Be Used With 6V6980 Nozzle Puller Group{0706,1254}
1985/06/10
Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02
New Bleed Screw Used In Fuel Injection Nozzle{1254}
1985/09/23
Fuel Transfer Pump Improved{1256}
1985/10/14
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Bolt Removed From Governor And Fuel Injection Pump Group{1286,1253,1287}
1985/11/18
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
New Material Used For Disc In Valve Assemblies Of Fuel Transfer Pump Groups{1256}
1986/09/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles{1254,1250}
1986/09/29
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Larger Diameter Holes Are Now Used In The Rocker Arm Shaft To Give More Oil Flow To Rocker Arm Bearings{1102}
1977/11/21
Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time{1286,1256,1251}
1978/07/03
Improved Guide Pin For Fuel Injection Pump Lifters{1251}
1978/08/21
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
Seals In Variable Timing Advance Available For Parts Service{1272}
1988/07/11
Check Assembled Dimension For Rack Lever Travel If Governor Housing Assembly Is Replaced {1264}
1988/12/19
A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing{0626}
1979/01/08
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Improvements Made To Fuel Injection Pump And Governor Group{1253,1281}
1979/12/10
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
New Bleed Screw Used On 7000 Series Fuel Injection Nozzles{1254}
1989/03/06
Be Sure To Tighten Fuel Injection Line Clamps To The Correct Torque{1252}
1989/09/11
New Shaft Bracket And Oil Supply Plug Used In Rocker Valve Shaft Assembly{1102,7553}
1991/03/25
New Shaft Bracket And Oil Supply Plug Used In Rocker Valve Shaft Assembly{1102,7553}
1991/04/15
New Gaskets Help Prevent Leaks From Fuel System Governors{1264}
1991/12/02
Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN){1254}
1992/04/20
Improved Fuel Injection Line Assemblies And Clamps Used{1252}
1992/11/09
New Fuel Pump Drive Idler Gear Assembly And Shaft Used In Front Timing Gear Groups {1206}
1993/06/14
Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23
New Fuel Nozzles Resist Adapter Cracking And Leaking {1254}
1999/06/14
Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14
Do not Use the 1U-6661 Pop Tester Gp to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/08

Caterpillar Parts SIS Catalog 3306 :

PUMP GP-FUEL INJECTION
1W-6539 PUMP GP-FUEL INJECTION
PUMP & MTG GP-FUEL TRANSFER
2W-4160 PUMP & MTG GP-FUEL TRANSFER
PROTECTION GP-FUEL SYSTEM
9Y-0183 PROTECTION GP-FUEL SYSTEM
LINES GP-FUEL INJECTION
9Y-3760 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9Y-3759 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9Y-1214 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9Y-0750 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9Y-0749 LINES GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6I-2829 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6I-2830 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
6I-2831 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7C-1916 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7C-3994 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7C-3994 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7W-5928 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
8N-2517 PUMP GP-FUEL INJECTION

Truck sale:

 
9,775 
Caterpillar 3306T, Marine Propulsion / Auxiliary Engines, Construction
- Marine Propulsion / Auxiliary Engines
FINANZAUTO S.A.
Caterpillar 3306T, Stationary Generator Sets, Construction
35,500 
Caterpillar 3306T, Stationary Generator Sets, Construction
- Stationary Generator Sets
RING POWER CORP.
Caterpillar 3306, Stationary Generator Sets, Construction
8,185 
Caterpillar 3306, Stationary Generator Sets, Construction
- Stationary Generator Sets
TOROMONT POWER SYSTEMS
Caterpillar 3306, Stationary Generator Sets, Construction
41,500 
Caterpillar 3306, Stationary Generator Sets, Construction
- Stationary Generator Sets
MACALLISTER MACHINERY CO., INC
 
35,000 
Caterpillar 3306, Stationary Generator Sets, Construction
- Stationary Generator Sets
MACALLISTER MACHINERY CO., INC
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.