AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

6I-1098 GOVERNOR GP PART OF 8N-6951 GOVERNOR GP AN ATTACHMENT 3408 ENGINE - MACHINE


FUEL SYSTEM
GOVERNOR GP
PUMP GP-FUEL INJECTION

ENGINE - MACHINE 3408 ENGINE - MACHINE 67U
 3408B Industrial Engine 67U11092-UP SEBP1518 3408 67U   (2018)

FUEL SYSTEM

GOVERNOR GP
GOVERNOR GP
4W-7375 GOVERNOR GP
GOVERNOR GP
4W-8678 GOVERNOR GP
GOVERNOR GP
6I-1098 GOVERNOR GP
GOVERNOR GP
7N-6271 GOVERNOR GP
GOVERNOR GP
8N-2154 GOVERNOR GP
GOVERNOR GP
8N-2367 GOVERNOR GP
 

#SEBP15180880
 

6I-1098: GOVERNOR GP

6I-1098 GOVERNOR GP
PART OF 8N-6951 GOVERNOR GP
AN ATTACHMENT
i00391809 SEBP1518
6I1098 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6I-0984 [1] KIT-RELIEF VALVE (GOVERNOR)  
    (INCLUDES SLEEVE, PLUNGER, SPRINGS, & PLUG)
2. 4P-8388 [1] CLUTCH AS  
3. 4P-9624 [1] KIT-COVER REPAIR (GOVERNOR)  
    (INCLUDES SCREWS, NUTS, WASHERS, & COVER)
4. 6I-1178 [1] KIT-DROOP SHAFT (GOVERNOR)  
    (INCLUDES NUT, WASHER, SCREWS, SHAFT, BRACKET, & LEVER)
5. 4P-9622 [1] KIT-REPAIR (GOVERNOR)  
    (INCLUDES LOCKING NUT, TERMINAL SHAFT BUSHINGS, TERMINAL SHAFTS, & PIVOT PIN)
6. 4W-5123 [1] MOTOR AS  
  7N-7779 [1] SOCKET-CONNECTOR (14-GA TO 18-GA)  
  7N-7780 [1] PIN-CONNECTOR (14-GA TO 18-GA)  
  7N-9738 [1] HOUSING-RECEPTACLE (14-GA TO 18-GA)  
7. 4P-9623 [1] KIT-PLUG REPAIR (GOVERNOR)  
    (INCLUDES PLUGS & NEEDLE VALVE)
8. 4P-9625 [1] KIT-GOVERNOR CONTROL STOP  
    (INCLUDES NUT, WASHER, & SCREW)
9. 4P-9627 [1] KIT-GOVERNOR VALVE  
    (INCLUDES IDLER GEAR, GEAR POST, GUIDE BUSHING, VALVE PLUNGER, PLUNGER NUT, & PILOT VALVE BUSHING)
10. 6I-1103 [1] SPRING AS  
11. 7N-0001 [1] BALL HEAD AS  
12. 4P-9626 [1] KIT-GOVERNOR LINKAGE  
    (INCLUDES NUT, SPRING, BLOCKS, PIN, SPACER, & FLOATING LEVER)
13. 4P-9629 [1] KIT-GOVERNOR PISTON  
    (INCLUDES POWER PISTON & BUFFER PISTON)
14. 4P-9628 [1] KIT-BUFFER SPRING (GOVERNOR)  
    (INCLUDES BUFFER SPRINGS & BUFFER SEAT)
   
    AVAILABLE REPAIR KIT(S):
  4P-9621 [1] KIT-GOVERNOR REPAIR  
    (INCLUDES GASKET, SPRING PIN, SEALS, ROLL PINS, WASHER, PLUGS, SEAL-O-RINGS, & RETAINING RINGS)
 

#SEBP15180881
 

7N-6271: GOVERNOR GP

7N-6271 GOVERNOR GP
PART OF 1N-3277 PUMP GP-GOV, FUEL INJ & TFR
AN ATTACHMENT
i00410154 SEBP1518
7N6271 GOVERNOR GP Parts scheme 7N6271 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-3363 [1] HOUSING AS-GOVERNOR  
2. 8S-0134 [1] BUSHING  
3. 8M-8403 [1] SPRING-GUIDE  
4. 9S-8001 [1] PLUG  
  4J-7533 [1] SEAL-O-RING  
5. 9S-0798 [1] BUSHING  
6. 8T-2604 C [2] SEAL-LIP TYPE  
7. 8L-4308 [1] BOLT (5/16-18X2.75-IN)  
8. 9M-1974 C [5] WASHER-HARD (8.8X16X2-MM THK)  
9. 2B-2695 [1] BOLT (5/16-18X0.875-IN)  
10. 2P-8707 [1] PLATE AS-GOVERNOR  
11. 8L-4175 [1] DOWEL  
12. 0S-1594 [1] BOLT (3/8-16X1-IN)  
13. 1D-4540 [3] BOLT (5/16-18X2.75-IN)  
14. 1N-4656 C [1] SHAFT  
15. 9N-1917 C [1] COVER AS  
16. 3P-0009 [1] INSULATOR  
17. 9N-1916 [1] LEVER-SHUTOFF  
18. 5M-6228 [1] BEARING AS-NEEDLE  
19. 033-5359 [4] SCREW-HEAD BOLT  
20. 9N-2165 [1] LEVER-SOLENOID  
21. 1S-7984 [1] BUSHING  
22. 1K-4703 [1] WASHER (13.1X22.2X1.6-MM THK)  
23. 5P-0796 [2] SEAL-LIP TYPE  
24. 4N-0951 [1] SHAFT-SHUTOFF  
25. 2J-0157 [2] SEAL-O-RING  
26. 9N-3324 [1] SCREW-ADJUSTMENT (HI-IDLE)  
27. 7N-7325 [1] SCREW-ADJUSTMENT (LO-IDLE)  
28. 5L-8992 [1] COVER-ADJUSTMENT  
29. 5P-6945 C [1] BOLT (1/4-20X1.125-IN)  
  4B-9747 [1] WASHER (0.266X0.375X0.031-IN THK)  
30. 8L-4155 [1] SETSCREW  
  1B-4201 [1] NUT-FULL (1/4-28-THD)  
31. 9M-4704 [1] BOLT (8-32X1-IN)  
32. 8L-4154 [1] COLLAR-LOAD STOP  
33. 2N-4386 [1] COVER  
34. 1B-2714 [2] BOLT (1/4-20X2.5-IN)  
  1B-4330 [2] NUT (1/4-20-THD)  
  5P-0537 [4] WASHER-HARD (7.2X14.5X2-MM THK)  
35. 6L-1597 C [2] GASKET  
36. 2P-8669 [1] GASKET  
37. 2W-1493 C [1] LEVER AS-CONTROL  
  2W-1491 C [1] LEVER-CONTROL  
38. 9M-9788 [1] PLUNGER  
39. 7M-7316 [1] SPRING  
40. 5H-1351 [1] PIN-SPRING  
41. 2P-8679 [1] STRAINER AS (FUEL)  
42. 2P-8697 [1] GASKET  
43. 6N-3504 [1] SEAT-GOVERNOR SPRING  
44. 4N-1870 [1] GASKET-HOUSING  
45. 9S-8008 [1] PLUG (1-1/16-12-THD)  
  3D-2824 [1] SEAL-O-RING  
46. 5M-6214 [1] PLUG (1/8-27 PTF)  
47. 9N-3684 Y [1] PLATE GP-GOVERNOR ADAPTER  
48. 6N-9040 [1] DRIVE AS-FLEXIBLE  
49. 2W-9780 C [1] PIN AS  
50. 6N-8780 [1] STOP  
51. 8H-9181 [1] SPRING-BUMPER  
52. 4W-7654 C [1] BOLT (1/4-28X1.25-IN)  
53. 6N-8793 [1] SPRING  
54. 5L-8991 [1] GASKET-COVER  
55. 1B-9575 [1] BOLT (5/16-18X1.56-IN)  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

#SEBP15180882
 

8N-2154: GOVERNOR GP

8N-2154 GOVERNOR GP
OUTPUT SHAFT
PART OF 1W-2365 CONVERSION GP-GOVERNOR
AN ATTACHMENT
i00429463 SEBP1518
8N2154 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8N-7123 [1] ROD AS  
  5P-6672 [1] ROD END  
  4F-2294 [2] NUT-JAM (5/16-24-THD)  
  061-7284 [1] ROD  
  7H-3639 [1] PIN-SPRING  
2. 8N-2367 Y [1] GOVERNOR GP  
3. 032-1268 [1] CONNECTOR (90-DEG)  
4. 8N-2155 [1] TUBE AS  
5. 1N-3997 [2] GASKET  
6. 8N-2150 [1] ADAPTER  
7. 7N-3481 [1] ADAPTER AS-ANGLE  
8. 5M-6213 [1] PLUG-PIPE (1/4-18-THD)  
9. 8N-2148 [1] COUPLING  
10. 032-1267 [1] CONNECTOR (STRAIGHT)  
11. 0L-1590 [1] BOLT (1/4-28X1.125-IN)  
  5P-0537 [1] WASHER-HARD (7.2X14.5X2-MM THK)  
12. 1B-8735 [1] KEY-WOODRUFF  
13. 6V-0975 [4] STUD-TAPERLOCK  
14. 1D-4716 [5] NUT-FULL (5/16-18-THD)  
15. 8N-2149 [1] LEVER  
16. 6N-1172 [2] SLEEVE  
  1D-4538 [1] BOLT (5/16-18X2.25-IN)  
  9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
  Y   SEPARATE ILLUSTRATION
 

#SEBP15180883
 

8N-2367: GOVERNOR GP

8N-2367 GOVERNOR GP
PART OF 8N-2154 GOVERNOR GP
Type 1
AN ATTACHMENT
i00429607 SEBP1518
8N2367 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
2. 4B-3388 [1] BOLT (5/16-18X1.125-IN)  
3. 032-8870 [1] PIN-SPRING  
4. 8N-2153 [1] LEVER AS  
5. 6V-1033 C [1] END-BEARING ROD  
6. 5B-4685 [1] PIN-TAPERED  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP15180884
 

8N-2367: GOVERNOR GP

8N-2367 GOVERNOR GP
PART OF 8N-2154 GOVERNOR GP
Type 2
AN ATTACHMENT
i00429611 SEBP1518
8N2367 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
2. 4B-3388 [1] BOLT (5/16-18X1.125-IN)  
3. 032-8870 [1] PIN-SPRING  
4. 8N-2153 [1] LEVER AS  
5. 6V-1033 [1] END-BEARING ROD  
6. 5B-4685 [1] PIN-TAPERED  
7. 7W-1994 C [1] GOVERNOR GP  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP15180885
 

8N-6951: GOVERNOR GP

8N-6951 GOVERNOR GP
WOODWARD PSG-24 VOLT MOTOR
PART OF 1N-3543, 7W-9501, 7W-9502, 8N-3104 CONVERSION GP-GOVERNOR
AN ATTACHMENT
i00413388 SEBP1518
8N6951 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 3L-1474 [1] PIN-TAPERED  
2. 7N-2299 [1] LEVER-GOVERNOR OUTPUT  
3. 4W-6811 CY [1] GOVERNOR GP  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

#SEBP15180886
 

8N-6951: GOVERNOR GP

8N-6951 GOVERNOR GP
WOODWARD PSG-24 VOLT MOTOR
PART OF 7W-9502, 8N-3104 CONVERSION GP-GOVERNOR
AN ATTACHMENT
i00413391 SEBP1518
8N6951 GOVERNOR GP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4F-7957 C [1] BOLT (1/4-20X0.875-IN)  
2. 8N-0771 C [1] LEVER-GOVERNOR  
3. 6I-1098 CY [1] GOVERNOR GP  
4. 5P-0537 C [1] WASHER-HARD (7.2X14.5X2-MM THK)  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP15180887
 

2W-4533: HOUSING AS-GOVERNOR DRIVE

2W-4533 HOUSING AS-GOVERNOR DRIVE
GOVERNOR ADAPTER
PART OF 1N-4932, 6N-1656 DRIVE GP-GOVERNOR
AN ATTACHMENT
i05010971 SEBP1518
2W4533 HOUSING AS-GOVERNOR DRIVE Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4H-8920 [1] DOWEL  
2. 4N-0898 [1] DOWEL-HOLLOW  
3. 2L-7103 [1] BEARING AS-NEEDLE  
4. 5P-0796 [1] SEAL-LIP TYPE  
5. 1F-4622 [1] BEARING AS-NEEDLE  
 

#SEBP15180888
 

4N-0779: HOUSING GP-FUEL PUMP

4N-0779 HOUSING GP-FUEL PUMP
PART OF 4W-4737, 4W-6036, 7N-1241, 7W-9445, 8N-9453 PUMP GP-FUEL INJECTION
AN ATTACHMENT
i00369869 SEBP1518
4N0779 HOUSING GP-FUEL PUMP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-7266 [1] SHAFT-PUMP IDLER  
2. 7N-0242 [2] BUSHING  
3. 8L-6565 [1] PIN-SPRING  
4. 1S-7984 [2] BUSHING  
5. 2M-2489 [2] SEAL-LIP TYPE  
6. 9S-4160 [2] BUSHING  
7. 4M-1474 [4] PIN-LIFTER GUIDE  
8. 9L-9766 [2] PIN-PLUNGER LIFT  
9. 6N-8441 [2] BUSHING  
10. 4N-0899 [1] DOWEL-HOLLOW  
11. 1P-0232 [8] BALL  
  1P-0234 [8] DOWEL  
12. 4N-0775 [2] DOWEL-HOLLOW  
13. 5B-9318 [1] BALL  
 

#SEBP15180889
 

7N-4574: HOUSING GP-FUEL PUMP

7N-4574 HOUSING GP-FUEL PUMP
PART OF 4W-0150, 4W-6012, 7N-6389, 7W-1983 PUMP GP-FUEL INJECTION
ALSO AN ATTACHMENT
i00108190 SEBP1518
7N4574 HOUSING GP-FUEL PUMP Parts scheme
  For full view, you need register

Parts for your 3408 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-7266 [1] SHAFT-PUMP IDLER  
2. 7N-0242 [2] BUSHING  
3. 5B-9318 [1] BALL  
4. 4N-0775 [2] DOWEL-HOLLOW  
5. 8L-6565 [1] PIN-SPRING  
6. 9S-4160 [2] BUSHING  
7. 4M-1474 [4] PIN-LIFTER GUIDE  
8. 9L-9766 [2] PIN-PLUNGER LIFT  
9. 6N-8441 [2] BUSHING  
10. 4N-0899 [1] DOWEL-HOLLOW  
11. 1P-0232 [8] BALL  
  1P-0234 [8] DOWEL  
12. 4N-0952 C [1] PLUG-CUP  
  C   CHANGE FROM PREVIOUS TYPE
 

Information:

Engine News
New Woodward Governor Control Used On Diesel Engines; Former Control Now Used On Gas Engines Only
1979/04/04
Conversion Group Available To Install Woodward Governor On Engines Equipped With Mechanical Governor
1979/04/25
To Prevent A Possible Change In The Fuel Rack Setting, A Specific Assembly Procedure Must Be Used To Tighten The Bolt On The Governor Stop Collar
1979/08/08
Explanation Of Differences In Timing Advance Information
1981/08/26
Part Number For Fuel Injection Pump Group In New Location
1981/11/25
New Idler Shaft Used In Fuel Transfer Pumps
1982/02/24
Fuel Rack Slots Have Improved Wear Resistance
1982/05/12
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
Changes In Engine RPM; Governor Does Not Operate Correctly
1982/10/20
Changes In Engine RPM; Governor Does Not Operate Correctly
1983/01/19
New Specification For Clearance Between Fuel Rack Slot And Cross Link
1983/05/25
Improved Governor Control Shaft And Seal Will Help Prevent Oil Leakage
1983/07/06
Service Information For Woodward Governors
1983/10/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30
Procedure To Remove Sharp Edges From Fuel Racks
1984/02/22
New EG3P Actuator Assemblies Available
1984/03/07
Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators
1984/05/16
New Seal For Fuel Injection Pump Housing Is More Resistant To Heat Damage
1984/05/16
New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage
1984/06/20
Fill Oil Sump Before Installing Woodward Governor
1985/01/16
Cross Link Between Fuel Racks Has Smoother Surface
1985/03/01
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct
1986/05/01
New Conversion Groups Available To Convert From Hydramechanical Governors To Woodward PSG Governors
1986/05/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
New Steel Fuel Injection Pump Lifters Should Not Be Mixed With Aluminum Lifters
1987/10/01
New Fuel Shutoff Solenoid Assembly Used
1988/11/01
New Throttle Shaft Bearing Sleeves Used In Governor Housing Assembly
1990/08/01
Governor Control Motor Polarity May Require A Change
1990/11/01
Replace Camshaft And Install New Lifters If Pitting, Spalling, Or Wear Occurs On Lobes Of 4N0599 And 4N0602 Camshafts In Fuel Injection Pump Groups
1991/05/01
Corrections For Systems Operation, Troubleshooting, And Specifications For 2301 Electric Governors For Generator Set And Industrial Engines, SENR2928-01
1991/05/01
Procedure To Increase Fuel Transfer Pump Pressure {1256}
1995/04/01
Pressure Compensated Simple Governor (PSG Governor) Changes From Aluminum To Cast Iron Housing {1264}
1995/04/01
Woodward Control Assemblies Have Changed Part Numbers To Provide The CE Marking For Electromagnetic Compatibility (EMC) Directives{1264}
1996/05/09
Improved Governor Servo Components Available For Use With Energize To Run Solenoids; Energize To Run Solenoid Stop Bolt Adjustment Procedure{1264,1259}
1996/06/12
Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/23
New Spring Used In Fuel Ratio Control
1977/03/15
New 5P4185 Fuel Pump Timing Pin To Be Used Only On 3408 And 3412 Engines
1977/05/13
Improvements To Fuel Injection Pump And Governor
1977/06/08
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Fuel Transfer Pump Shaft With Chromium Plate
1977/10/12
New Governor Spring Changes Speed Regulation
1977/11/09
Change In Design Of Engine Governor, Fuel Injection And Transfer Pump Groups, And Fuel Ratio Control Groups
1978/02/08
New Tachometer Drive Adapter Assembly Prevents Failure Of The Seals For The Tachometer Drive Group And Transfer Pump
1978/03/01
O-Ring Seals Of A Different Material Are Now Used On The Outside Diameter Of The Servo Cylinder In Governors
1978/05/03
A One-Piece Spring Seat Is Now Used In The Governor
1978/07/05
New Dashpot Spring Gives A Reduction In "Overshoot"
1978/07/05
Different O-Ring Seals Now Used In Fuel Injection Pump Group
1978/08/30
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Fuel System and Fuel Ratio Control Test Procedure{1264, 1278}
Fuel System and Fuel Ratio Control Test Procedure{1264, 1278}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Wiring Polarity on Woodward 2301 Governors{1289}
Wiring Polarity on Woodward 2301 Governors{1289}
Installation Of 6N6193 Governor Adapter Plate Service Group{1264}
Installation Of 6N6193 Governor Adapter Plate Service Group{1264}
Installation Of 4N779 And 7N6124 Fuel Injection Pump Housing Assemblies Or Fuel Injection Pump Groups{1251, 1253}
Installation Of 4N779 And 7N6124 Fuel Injection Pump Housing Assemblies Or Fuel Injection Pump Groups{1251, 1253}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N3104 Governor Conversion Group (Woodward PSG){1250}
Installation Of 8N3104 Governor Conversion Group (Woodward PSG){1250}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Service Letter-NACD
The Governor Needs To Be Updated On Certain 3408 Generator Set, 3408 Industrial, And 3412 Generator Set Engines Equipped With a 3% Regulation Hydromechanical Governor And An Energized-To-Run Shut-Off Solenoid Group
The Governor Needs To Be Updated On Certain 3408 Generator Set, 3408 Industrial, And 3412 Generator Set Engines Equipped With a 3% Regulation Hydromechanical Governor And An Energized-To-Run Shut-Off Solenoid Group
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Technical Information Bulletin
Remanufactured Fuel Injection Nozzles
Remanufactured Fuel Injection Nozzles
3400 V - Block Cleaniness at Gov'n Oil Supply Line
3400 V - Block Cleaniness at Gov'n Oil Supply Line
Specifications
Fuel Injection Pump
3408C & 3412C INDUSTRIAL ENGINES
Fuel Injection Pump Housing
3408C & 3412C INDUSTRIAL ENGINES
Governor
3408C & 3412C INDUSTRIAL ENGINES
Governor And Fuel Pump Drive<BR> (Automatic Timing Advance Unit)
3408C & 3412C INDUSTRIAL ENGINES
Fuel Transfer Pump Drive
3408C & 3412C INDUSTRIAL ENGINES
Fuel Transfer Pump
3408C & 3412C INDUSTRIAL ENGINES
Governor Control
3408C & 3412C INDUSTRIAL ENGINES
Woodward PSG Governor
3408 & 3408B INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Governor Linkage<BR> (Woodward EG-3P)
3408 & 3408B INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Governor Controls
3408 & 3408B INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Governor Air Actuator
3408 & 3408B INDUSTRIAL & MARINE ENGINE ATTACHMENTS
Service Letter-China
The Governor Needs To Be Updated On Certain 3408 Generator Set, 3408 Industrial, And 3412 Generator Set Engines Equipped With a 3% Regulation Hydromechanical Governor And An Energized-To-Run Shut-Off Solenoid Group
The Governor Needs To Be Updated On Certain 3408 Generator Set, 3408 Industrial, And 3412 Generator Set Engines Equipped With a 3% Regulation Hydromechanical Governor And An Energized-To-Run Shut-Off Solenoid Group
Service Letter-Asia
Systems Operation
Systems Operation
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Installation And Operation
2301A SPEED CONTROL
Service Letter-APD
The Governor Needs To Be Updated On Certain 3408 Generator Set, 3408 Industrial, And 3412 Generator Set Engines Equipped With a 3% Regulation Hydromechanical Governor And An Energized-To-Run Shut-Off Solenoid Group
The Governor Needs To Be Updated On Certain 3408 Generator Set, 3408 Industrial, And 3412 Generator Set Engines Equipped With a 3% Regulation Hydromechanical Governor And An Energized-To-Run Shut-Off Solenoid Group
Testing and Adjusting
Testing and Adjusting
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Installation And Operation
2301A SPEED CONTROL
Troubleshooting
Introduction
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem Index
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 1: Fuel Linkage Has Limited Travel, Binds, Or Takes Excessive Force
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 2: Engine Will Not Start
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 3: Engine Will Not Carry Load (Low Power)
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 4: Engine Will Not Decelerate. Engine Will Not Idle.
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 5: Engine Speed Not Constant
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 6: Engine Overspeeds
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 7: Engine Does Not Share Load (For Load Share Units Only)
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Problem No. 8: Engine Does Not Parallel
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Service Procedures
2301 ELECTRIC GOVERNOR FOR GENERATOR SET AND INDUSTRIAL ENGI
Chapter 5. Troubleshooting
2301A SPEED CONTROL
Appendix A. Guide for Handling and Protection of Electronic Controls, Printed Circuit Boards, &amp; Modules
2301A SPEED CONTROL
Appendix B. EMI Controls in Electronic Governing Systems
2301A SPEED CONTROL
Disassembly and Assembly
Governor &amp; Fuel Pump Drive
3408C & 3412C INDUSTRIAL ENGINES
Fuel Injection Pumps
3408C & 3412C INDUSTRIAL ENGINES
Fuel Transfer Pump
3408C & 3412C INDUSTRIAL ENGINES
Governor &amp; Fuel Injection Pump Housing
3408C & 3412C INDUSTRIAL ENGINES
Fuel Shutoff Solenoid
3408C & 3412C INDUSTRIAL ENGINES
Governor
3408 & 3408B INDUSTRIAL AND MARINE ENGINES
Fuel Injection Pump Housing And Governor
3408 & 3408B INDUSTRIAL AND MARINE ENGINES
Fuel Injection Pump Housing
3408 & 3408B INDUSTRIAL AND MARINE ENGINES
Service Magazine
Modification Of 5P1768 Pointer Assembly Necessary For Use On Some Fuel Injection Pump Housings{1253,0653}
1980/03/31
6V2029 Fixture Group Available For Adjustment Of Air/Fuel Ratio Control {0626,1278,0652}
1981/03/23
Troubleshooting The Fuel Ratio Control Group For Low Power Complaints{1278}
1981/08/24
Part Number For Fuel Injection Pump Group In New Location{1253,1286}
1981/11/09
New Idler Shaft Used In Fuel Transfer Pumps{1256}
1982/02/22
Fuel Rack Slots Have Improved Wear Resistance{1257}
1982/05/10
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Changes In Engine RPM; Governor Does Not Operate Correctly{1264}
1982/10/18
Changes In Engine RPM; Governor Does Not Operate Correctly{1264}
1983/01/10
New Rack Shutoff Solenoid Available{1257,1259}
1983/02/28
New Specification For Clearance Between Fuel Rack Slot And Cross Link{1257}
1983/05/16
Improved Governor Control Shaft And Seal Will Help Prevent Oil Leakage{1265}
1983/07/04
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Procedure To Remove Sharp Edges From Fuel Racks {1257,1253}
1984/02/06
New EG3P Actuator Assemblies Available{1289}
1984/02/27
Only The External Needle Valve Can Be Adjusted On Woodward EG3P or EG10P Actuators{1265,1289}
1984/04/23
New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14
Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Cross Link Between Fuel Racks Has Smoother Surface{1250,1257}
1985/03/11
Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02
Steel Fuel Pump Lifter Used{1250,1251}
1985/09/02
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24
New Conversion Groups Available To Convert From Hydramechanical Governors To Woodward PSG Governors{1289}
1986/04/21
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
More Precise Governor Speed Adjustment Possible With Attachment Governor Control Groups{1265,1264,1250}
1986/06/02
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
Improvements To Fuel Injection Pump And Governor{1286}
1977/06/06
Fuel Transfer Pump Shaft With Chromium Plate{1256}
1977/10/10
New Governor Spring Changes Speed Regulation{1264,1286}
1977/10/31
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Change In Design Of Engine Governor, Fuel Injection And Transfer Pump Groups, And Fuel Ratio Control Groups{1264,1278,1286}
1978/01/23
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
New Tachometer Drive Adapter Assembly Prevents Failure Of The Seals For the Tachometer Drive Group And Transfer Pump{7462,1256}
1978/02/27
Soft Washers And Lockwashers Are Now Used With The Mounting Bolts For Air-Fuel Ratio Control{1278,1264}
1978/03/13
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
O-Ring Seals Of A Different Material Are Now Used On The Outside Diameter Of The Servo Cylinder In Governors{1264}
1978/05/01
New Dashpot Spring Gives A Reduction In &quot;Overshoot&quot;{1264}
1978/06/26
A One-Piece Spring Seat Is Now Used In The Governor{1264}
1978/06/26
Different O-Ring Seals Now Used In Fuel Injection Pump Group{1251}
1978/08/28
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
New Woodward Governor Control Used On Diesel Engines; Former Control Now Used On Gas Engines Only{1265}
1979/03/19
Conversion Group Available To Install Woodward Governor On Engines Equipped With Mechanical Governor{1264}
1979/04/09
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
To Prevent A Possible Change In The Fuel Rack Setting, A Specific Assembly Procedure Must Be Used To Tighten The Bolt On The Governor Stop Collar{1259,1257,1250}
1979/07/02
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
New Throttle Shaft Bearing Sleeves Used In Governor Housing Assembly{1365}
1990/07/30
Governor Control Motor Polarity May Require A Change{1265,1408,7556}
1990/10/29
Replace Camshaft And Install New Lifters If Pitting, Spalling, Or Wear Occurs On Lobes Of 4N0599 And 4N0602 Camshafts In Fuel Injection Pump Groups{1251,1253}
1991/05/20
New Components Help Prevent Air Leaks In Improved Fuel Ratio Control Groups{1278}
1992/05/25
New Diaphragm Used In Fuel Ratio Control Groups{1278}
1992/06/15
Improved Fuel Pump Bonnet Seal Has Better Heat Resistance {1251}
1994/09/12
Tamper Resistant Plugs And Tamper Resistant Bolts Used To Prevent Changes To Fuel Ratio Control (FRC) Setting{1278,1287}
1996/01/22
Improved Governor Servo Components Available For Use With Energize To Run Solenoids; Energize To Run Solenoid Stop Bolt Adjustment Procedure{1264,1259}
1996/06/03

Caterpillar Parts SIS Catalog 3408 :

GOVERNOR GP
4W-8678 GOVERNOR GP
GOVERNOR GP
4W-7375 GOVERNOR GP
GOVERNOR GP
4W-6811 GOVERNOR GP
GOVERNOR GP
4W-6811 GOVERNOR GP
GOVERNOR GP
4W-6017 GOVERNOR GP
GOVERNOR GP
4W-6017 GOVERNOR GP
GOVERNOR GP
4W-6013 GOVERNOR GP
GOVERNOR GP
4W-6013 GOVERNOR GP
GOVERNOR GP
7N-6271 GOVERNOR GP
GOVERNOR GP
8N-2154 GOVERNOR GP
GOVERNOR GP
8N-2367 GOVERNOR GP
GOVERNOR GP
8N-2367 GOVERNOR GP
GOVERNOR GP
8N-6951 GOVERNOR GP
GOVERNOR GP
8N-6951 GOVERNOR GP
HOUSING AS-GOVERNOR DRIVE
2W-4533 HOUSING AS-GOVERNOR DRIVE
HOUSING GP-FUEL PUMP
4N-0779 HOUSING GP-FUEL PUMP

Truck sale:

Caterpillar 3408 IND, Construction
45,000 
Caterpillar 3408 IND, Construction
- Industrial engines
LOUISIANA CAT POWER SYSTEMS
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.