AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

7W-2063 PUMP GP-FUEL INJECTION S/N 95Y644-1064 AN ATTACHMENT 3508 INDUSTRIAL ENGINE


FUEL SYSTEM
PUMP GP-FUEL INJECTION
PUMP GP-FUEL PRIMING

INDUSTRIAL ENGINE 3508 INDUSTRIAL ENGINE 68Z
 3508 Industrial Engine 68Z00694-01092 SEBP1575 3508 68Z   (1982)

FUEL SYSTEM

PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7C-3764 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7W-2062 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7W-2063 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-1796 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-1796 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-6988 PUMP GP-FUEL INJECTION
 

#SEBP15750890
 

7W-2063: PUMP GP-FUEL INJECTION

7W-2063 PUMP GP-FUEL INJECTION
S/N 95Y644-1064
AN ATTACHMENT
i00431804 SEBP1575
7W2063 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4F-7226 [1] BOLT (7/16-14X4-IN)  
2. 7N-5487 [1] WASHER (12X22X9.5-MM THK)  
3. 1N-4910 [1] CLAMP-INJECTOR  
4. 7W-8668 [1] INJECTOR AS  
  2W-5200 [1] NUT AS-INJECTION VALVE  
5. 7N-5325 [1] CHECK-INJECTION VALVE  
6. 7N-5307 [1] CAGE-INJ CHECK VALVE  
7. 7N-5321 [1] SPRING-FUEL VALVE  
8. 7N-5312 [1] CAGE-INJECTION SPRING  
9. 7W-2237 [1] FOLLOWER  
10. 7N-5319 [1] SEAT-VALVE SPRING  
11. 7N-5314 [1] DEFLECTOR-SPILL  
12. 7N-5317 [1] SPRING-STOP PIN  
13. 7N-5318 [1] RETAINER-PIN  
14. 7N-5322 [1] RETAINER-GEAR  
15. 7N-5315 [1] SEAL-INJECTOR  
16. 7W-2236 [1] BODY AS  
17. 7N-5309 [1] RACK AS-INJECTOR  
18. 7N-5313 [1] GEAR (23 TEETH)  
19. 7N-5320 [1] PIN-INJECTION STOP  
20. 7W-0296 [1] SPRING-INJECTOR  
21. 7W-1034 [1] PLUNGER AS  
22. 7W-8667 [1] TIP AS  
23. 6V-1250 [1] SEAL-O-RING  
24. 8J-8725 [2] SEAL-O-RING  
25. 8N-9944 [1] PLUG  
    (LETTERS H, M, & L DENOTE HIGH, MEDIUM, & LOW FLOW RANGE)
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP15750891
 

9Y-1796: PUMP GP-FUEL INJECTION

9Y-1796 PUMP GP-FUEL INJECTION
S/N 95Y644-1064
Type 1
FOR USE WITH ENGINE RATINGS OF 1301 TO 1600 RPM
AN ATTACHMENT
i00092249 SEBP1575
9Y1796 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7E-3382 [1] INJECTOR GP-FUEL  
2. 1N-4910 [1] CLAMP-INJECTOR  
3. 4F-7226 [1] BOLT (7/16-14X4-IN)  
4. 7N-5487 [1] WASHER (12X22X9.5-MM THK)  
5. 7C-2615 [1] PLUG  
6. 8J-8725 [2] SEAL-O-RING  
7. 6V-1250 [1] SEAL-O-RING  
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP15750892
 

9Y-1796: PUMP GP-FUEL INJECTION

9Y-1796 PUMP GP-FUEL INJECTION
S/N 95Y644-1064
Type 2
FOR USE WITH ENGINE RATINGS OF 1301 TO 1600 RPM
AN ATTACHMENT
i00092250 SEBP1575
9Y1796 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4P-9076 CY [1] INJECTOR GP-FUEL  
2. 1N-4910 [1] CLAMP-INJECTOR  
3. 4F-7226 [1] BOLT (7/16-14X4-IN)  
4. 7N-5487 [1] WASHER (12X22X9.5-MM THK)  
5. 234-4182 [1] PLUG  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP15750893
 

9Y-6988: PUMP GP-FUEL INJECTION

9Y-6988 PUMP GP-FUEL INJECTION
S/N 95Y755-872
FOR USE WITH ENGINE RATINGS GREATER THAN 1600-RPM
i00445739 SEBP1575
9Y6988 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4P-9077 [1] INJECTOR GP-FUEL  
1A. 194-9584 [2] SEAL-O-RING  
1B. 6V-1250 [1] SEAL-O-RING  
2. 1N-4910 [1] CLAMP-INJECTOR  
3. 4F-7226 [1] BOLT (7/16-14X4-IN)  
4. 7N-5487 [1] WASHER (12X22X9.5-MM THK)  
5. 7C-2615 [1] PLUG  
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP15750894
 

9Y-6988: PUMP GP-FUEL INJECTION

9Y-6988 PUMP GP-FUEL INJECTION
S/N 95Y873-1064
FOR USE WITH ENGINE RATINGS GREATER THAN 1600-RPM
i00445741 SEBP1575
9Y6988 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 234-4182 [1] PLUG  
2. 1N-4910 [1] CLAMP-INJECTOR  
3. 4F-7226 [1] BOLT (7/16-14X4-IN)  
4. 7N-5487 [1] WASHER (12X22X9.5-MM THK)  
5. 4P-9077 [1] INJECTOR GP-FUEL  
5A. 6V-1250 [1] SEAL-O-RING  
5B. 194-9584 [2] SEAL-O-RING  
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP15750895
 

9Y-7841: PUMP GP-FUEL INJECTION

9Y-7841 PUMP GP-FUEL INJECTION
S/N 68Z754-825
i00432539 SEBP1575
9Y7841 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7E-3381 [1] INJECTOR GP-FUEL  
2. 1N-4910 [1] CLAMP-INJECTOR  
3. 4F-7226 [1] BOLT (7/16-14X4-IN)  
4. 7N-5487 [1] WASHER (12X22X9.5-MM THK)  
5. 7C-2615 [1] PLUG  
6. 8J-8725 [2] SEAL-O-RING  
7. 6V-1250 [1] SEAL-O-RING  
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP15750896
 

9Y-7841: PUMP GP-FUEL INJECTION

9Y-7841 PUMP GP-FUEL INJECTION
S/N 68Z826-1092
i00432543 SEBP1575
9Y7841 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4P-9075 C [1] INJECTOR GP-FUEL  
  194-9584 [2] SEAL-O-RING  
  5P-8065 [1] SEAL-O-RING  
  6V-1250 [1] SEAL-O-RING  
2. 1N-4910 [1] CLAMP-INJECTOR  
3. 4F-7226 [1] BOLT (7/16-14X4-IN)  
4. 7N-5487 [1] WASHER (12X22X9.5-MM THK)  
5. 234-4182 [1] PLUG  
  C   CHANGE FROM PREVIOUS TYPE
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP15750897
 

262-4960: PUMP GP-FUEL PRIMING

262-4960 PUMP GP-FUEL PRIMING -LH
AN ATTACHMENT
i02296439 SEBP1575
2624960 PUMP GP-FUEL PRIMING Parts scheme 2624960 PUMP GP-FUEL PRIMING Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1B-4971 [2] SPACER (0.406X1X1-IN THK)  
2. 1N-2897 [1] PLATE AS  
  0S-1594 B [5] BOLT (3/8-16X1-IN)  
  8M-9024 B [5] WASHER-HARD (10.2X22.5X5-MM THK)  
3. 2G-4504 I [1] HOSE AS  
4. 4P-7048 [1] BRACKET  
5. 5T-8088 I [1] HOSE AS  
6. 7N-8599 Y [1] PUMP GP-FUEL PRIMING  
7. 8B-9725 [2] BOSS  
8. 8N-7054 [1] SUPPORT  
9. 9M-0766 [1] BRACKET  
10. 9N-1752 [1] SPRING  
11. 127-7104 [1] BRACKET  
12. 127-7105 [1] ADAPTER  
13. 263-7285 [1] BRACKET  
14. 005-4173 [1] ELBOW  
15. 030-7943 [1] ELBOW  
16. 250-1498 [1] ELBOW AS  
  6V-4589 [1] SEAL-O-RING  
  [1] ELBOW AS  
17. 0L-2070 [5] BOLT (3/8-16X2.25-IN)  
18. 0S-1594 [5] BOLT (3/8-16X1-IN)  
19. 0S-1595 [3] BOLT (1/2-13X1.25-IN)  
20. 1A-0168 [1] BOLT (1/2-13X7.5-IN)  
21. 1F-7958 [1] NUT-FULL (1/2-13-THD)  
22. 1S-0994 [4] CLIP (LOOP)  
23. 1S-0996 [1] CLIP  
24. 2H-9523 [1] GROMMET  
25. 4B-9782 [1] BALL  
26. 4M-2442 [2] BOLT (1/2-13X12.32-IN)  
27. 5M-2894 [13] WASHER-HARD (10.2X18.5X2.5-MM THK)  
28. 5P-8245 [7] WASHER-HARD (13.5X25.5X3-MM THK)  
29. 6V-4362 [1] CONNECTOR  
30. 6V-4589 [2] SEAL-O-RING  
31. 6V-5049 [1] SEAL-O-RING  
32. 8L-2786 [1] SEAL-O-RING  
33. 8N-3480 [1] CLIP  
34. 9S-8006 [1] PLUG (7/8-14-THD)  
35. 9S-8752 [3] NUT-FULL (3/8-16-THD)  
  B   USE AS REQUIRED
  I   REFER TO HYDRAULIC INFORMATION SYSTEM
  Y   SEPARATE ILLUSTRATION
 

#SEBP15750898
 

314-6842: PUMP GP-FUEL PRIMING

314-6842 PUMP GP-FUEL PRIMING -LH, SEVERE ABRASION
AN ATTACHMENT
i02965982 SEBP1575
3146842 PUMP GP-FUEL PRIMING Parts scheme 3146842 PUMP GP-FUEL PRIMING Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1N-2897 [1] PLATE AS  
2. 2G-4504 I [1] HOSE AS  
3. 4P-7048 [1] BRACKET  
4. 5T-8088 I [1] HOSE AS  
5. 7N-8599 Y [1] PUMP GP-FUEL PRIMING  
6. 8B-9725 [2] BOSS  
7. 8N-7054 [1] SUPPORT  
8. 9M-0766 [1] BRACKET  
9. 9N-1752 [1] SPRING  
10. 9X-6772 [1] STRAP-CABLE  
11. 127-7104 [1] BRACKET  
12. 127-7105 [1] ADAPTER  
13. 250-1498 [1] ELBOW AS  
  6V-4589 [1] SEAL-O-RING  
  250-1497 [1] ELBOW  
14. 005-4173 [1] ELBOW  
15. 030-7943 [1] ELBOW  
16. 0L-2070 [5] BOLT (3/8-16X2.25-IN)  
17. 0S-1594 [5] BOLT (3/8-16X1-IN)  
18. 0S-1595 [2] BOLT (1/2-13X1.25-IN)  
19. 1A-2029 [1] BOLT (3/8-16X1.125-IN)  
20. 1S-0994 [4] CLIP (LOOP)  
21. 2H-9523 [1] GROMMET  
22. 4B-9782 [1] BALL  
23. 4M-2442 [2] BOLT (1/2-13X12.32-IN)  
24. 4P-8134 [1] CLIP (LADDER)  
25. 5M-2894 [14] WASHER-HARD (10.2X18.5X2.5-MM THK)  
26. 5P-8245 [4] WASHER-HARD (13.5X25.5X3-MM THK)  
27. 6V-4362 [1] CONNECTOR  
28. 6V-4589 [2] SEAL-O-RING  
29. 214-7568 [1] SEAL-O-RING  
30. 8L-2786 [1] SEAL-O-RING  
31. 8N-3480 [1] CLIP  
32. 9S-8006 [1] PLUG (7/8-14-THD)  
33. 9S-8752 [3] NUT-FULL (3/8-16-THD)  
  I   REFER TO HYDRAULIC INFORMATION SYSTEM
  Y   SEPARATE ILLUSTRATION
 

#SEBP15750899
 

7N-8599: PUMP GP-FUEL PRIMING

7N-8599 PUMP GP-FUEL PRIMING
PART OF 262-4960 PUMP GP-FUEL PRIMING
Type 1
AN ATTACHMENT
i00955669 SEBP1575
7N8599 PUMP GP-FUEL PRIMING Parts scheme
  For full view, you need register

Parts for your 3508 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-6804 [1] PUMP GP-FUEL PRIMING  
  1H-8171 [1] SEAL-O-RING  
2. 7B-2742 [1] BOLT (1/4-20X1.25-IN)  
3. 5P-0537 [1] WASHER-HARD (7.2X14.5X2-MM THK)  
4. 1P-0436 [1] GASKET (FUEL PRIMING PUMP)  
5. 9M-1974 [1] WASHER-HARD (8.8X16X2-MM THK)  
6. 1B-7182 [1] BOLT (5/16-18X1.25-IN)  
   
    AVAILABLE REPAIR KIT(S):
  8N-6287 [1] KIT-FUEL PRIMING KNOB  
    (KIT INCLUDES PIN, KNOBS, COVER, SPRING & WASHERS)
 

Information:

Engine News
Use 6V4172 Injector Sleeve When You Clean Fuel Injectors
1981/07/15
Explanation Of Differences In Timing Advance Information
1981/08/26
Bulged Capsule-Type Fuel Nozzles
1982/10/20
Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
Disconnect Fuel Lines And Install Caps Before Unit Injectors Are Removed
1983/02/16
Remove Plastic Plug From Fuel Transfer Pump
1983/04/27
Installation Procedure For Woodward 3161 and UG8 Governors
1983/07/06
Remanufactured Unit Injectors Are Available
1983/08/17
Inspect Camshaft And Lifters After A Failure In The Valve Mechanism Area
1984/01/18
Bolt Used Instead Of Stud In Governor Fastener Group To Prevent Damage To Governor Housing
1984/04/11
Quadrants Improved In Governor Control Groups
1984/07/11
Improved Valve Mechanism Cover Group Has A New Valve Cover And Seal
1985/01/16
Low Oil Level In Governor Can Cause Erratic Engine RPM
1985/02/01
Tighten Bolts To Correct Torque In 3161 Governor
1985/02/01
Valve Mechanism Groups Use New Lifter Assemblies
1985/08/01
Repair Kits Available For Air Actuator Used In Governor Control Groups
1985/09/01
Engine Valve Lash And Fuel Injection Timing Adjustment Procedure
1985/09/01
A Water Separator Can Help Prevent Fuel Injector Damage If Fuel Is Contaminated With Water
1986/01/01
Lubricate Clamp When Installing Unit Injector Assemblies
1986/01/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
How To Adjust Arming Pressure On Fuel Ratio Control On Caterpillar 3161 Governor
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
Improvements For Caterpillar 3161 Governors
1986/07/01
Fuel Injector Reference For 3500 Family Engines
1987/01/01
Improved Fuel Transfer Pump Cover; Weep Hole Moved
1987/03/01
New Washer Used In Fuel Transfer Pump Group
1987/04/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Features And Servicing Of The Various Caterpillar 3161 Governors
1987/06/01
Fuel Injector Trim Bolt
1987/06/01
Additional Information For Installing Fuel Injectors
1988/06/01
Two 11 mm Injectors Available For Parts Service
1988/07/01
Replacement Fuel Injector Nozzles With New Nose Cones Available
1988/08/01
One-Piece Tappet (Follower) Used In 11 mm (Type 2) Fuel Injectors
1988/12/01
Check Valve Added To Fuel Injection Lines
1989/05/01
New Connector With An Orifice Added To Fuel Injection Lines Groups To Help Prevent Cavitation
1989/07/01
Improved Control Rod Assembly Used In Fuel Injection Control Groups
1989/08/01
New Fuel Injectors Available For Parts Service
1989/09/01
New Fuel Injector Assemblies Used
1989/10/01
Fuel Injector Reference For 3500 Family of Engines
1989/10/01
New 7C9580 Fuel Injector (Type 2) Available To Replace 2W5201 Fuel Injector (Type 1)
1990/06/01
Some Fuel Injectors May Be Used In Mixed Sets
1990/06/01
If Trim Screw On Unit Injector Is Loose, Injector Must Be Replaced
1990/09/01
New "On Engine" Adjustment Procedure For 3161 Woodward Governor
1990/10/01
Remanufactured Type 1 Fuel Injector Assembly Available For 3500 Family Of Engines Equipped With UG8 Governors
1991/04/01
Corrections For Systems Operation, Troubleshooting, And Specifications For 2301 Electric Governors For Generator Set And Industrial Engines, SENR2928-01
1991/05/01
New Speed Setting Clutch Group For 3161 Woodward Governors
1991/06/01
End Clearance Specification Changed For Front Shaft In Fuel Injection Control
1991/10/01
New And Remanufactured Fuel Injector Reference
1992/05/01
New And Remanufactured Fuel Injector Reference
1993/01/01
New Fuel Injector Group Help Reduce Plunger And Barrel Seizures
1993/05/01
New 3161 Governor With Improved Fuel Limiter
1993/09/01
Fuel Dilution In The Engine Oil{1290,1318}
1994/05/01
New Seals Extend Life of Fuel Transfer Pump{1256}
1994/11/01
Be Sure The Cylinder Head Bore For the Unit Injector Is Clean When the Unit Injector Is Replaced {1290}
1999/07/01
Tightening Torque Increased For Nuts In Fuel Injector Wiring Harness Cap Assembly{1408}
1999/09/01
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
New Sequence for Adjusting the Fuel Injectors {1290, 1290}
2006/01/02
Troubleshooting Engines with Mechanical Unit Injection (MUI) {1000, 1254}
2006/01/02
Do not Use the 1U-6661 Pop Tester Gp to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/24
Do not Use the 1U-6661 Pop Tester Gp to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/24
Do not Use the 1U-6661 Pop Tester Gp or the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Operation and Maintenance Manual
Fuel Injector - Inspect/Adjust
3500 Industrial and Generator Set Engines
Special Instruction
Installation of 2W8511 Cam Loading Spring{1264}
Installation of 2W8511 Cam Loading Spring{1264}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation of Service Replacement Woodward Governor Group{1264}
Installation of Service Replacement Woodward Governor Group{1264}
Nozzle Assembly Replacement for Type 2 Fuel Injectors{1254}
Nozzle Assembly Replacement for Type 2 Fuel Injectors{1254}
Installation and Adjustment of 3161 Governor on 3500 Family of Engines{1264}
Installation and Adjustment of 3161 Governor on 3500 Family of Engines{1264}
Spring Replacement for Type 2 Fuel Injectors{1250}
Spring Replacement for Type 2 Fuel Injectors{1250}
3508 and 3512 LOCOMOTIVE ENGINES{1264}
3508 and 3512 LOCOMOTIVE ENGINES{1264}
3500 Electronic Unit Injection (EUI) Fuel Priming Procedure{1250, 1258}
3500 Electronic Unit Injection (EUI) Fuel Priming Procedure{1250, 1258}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N6414 Ether Starting Aid Group{1456}
Installation Of 8N6414 Ether Starting Aid Group{1456}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Installation Of 4W5391 Preregulator Box Assembly{1289}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Performing a Multiple Cylinder Cutout Test {1290}
Performing a Multiple Cylinder Cutout Test {1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290}
Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Specifications
Fuel Injector Mechanism
3500 Industrial Engines
Fuel Injector Mechanism
3500 Industrial Engines
Fuel Injector
3500 Industrial Engines
Fuel Injector Mechanism
3500 Industrial Engines
Systems Operation
Fuel Injector
3500 Industrial Engines
Fuel Injection Cycle
3500 Industrial Engines
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Testing and Adjusting
Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
3500 Industrial Engines
Fuel Injector Timing
3500 Industrial Engines
Fuel Injector Synchronization
3500 Industrial Engines
Checking Engine Cylinders
3500 Industrial Engines
Disassembly and Assembly
GOVERNOR
3500 INDUSTRIAL ENGINE
GOVERNOR DRIVE
3500 INDUSTRIAL ENGINE
FUEL INJECTORS
3500 INDUSTRIAL ENGINE
Fuel Transfer Pump
3500 INDUSTRIAL ENGINE
Governor
3500 INDUSTRIAL ENGINE
Governor Drive
3500 INDUSTRIAL ENGINE
Rocker Shafts And Push Rods
3500 INDUSTRIAL ENGINE
Rocker Shaft Assemblies
3500 INDUSTRIAL ENGINE
Fuel Injectors
3500 INDUSTRIAL ENGINE
Service Magazine
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Correct Installation Of Valve Lifter Prevents Problems With Valve Lash Adjustment{1102}
1983/01/10
Disconnect Fuel Lines And Install Caps Before Unit Injectors Are Removed{1274,1254,1251}
1983/01/17
Remove Plastic Plug From Fuel Transfer Pump{1256}
1983/04/25
Installation Procedure For Woodward 3161 and UG8 Governors{1264}
1983/05/30
Remanufactured Unit Injectors Are Available{1290}
1983/07/11
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Crankshaft Positions For Injector Timing And Valve Clearance Settings{0374,1104,1290}
1983/11/21
Bolt Used Instead Of Stud In Governor Fastener Group To Prevent Damage To Governor Housing {1264,1287}
1984/04/02
Quadrants Improved In Governor Control Groups{1265,1264}
1984/05/21
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Tighten Bolts To Correct Torque In 3161 Governor{1264}
1985/02/04
Rough Handling Can Move Droop Lever Out Of Position{1264}
1985/08/05
Adjusting Pneumatic Speed Control For Correct Operation{1264}
1985/09/02
Engine Valve Lash And Fuel Injection Timing Adjustment Procedure {1100,1251}
1985/09/16
List Of Mechanical Service Meters For Earlier 3500 Series Engines Using Mechanical Service Meters{1286}
1985/09/23
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
A Water Separator Can Help Prevent Fuel Injector Damage If Fuel Is Contaminated With Water{1263,1250,1273}
1985/12/09
Lubricate Clamp When Installing Unit Injector Assemblies{1290}
1986/01/13
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Improvements For Caterpillar 3161 Governors{1264}
1986/06/16
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Fuel Injector Reference For 3500 Family Engines{1290}
1987/01/19
Improved Injector Clamp Eliminates Interference With Bridge {1290}
1987/03/09
Improved Fuel Transfer Pump Cover; Weep Hole Moved{1255}
1987/03/23
Fuel Injection Timing Adjustment{1250}
1987/04/20
Fuel Injector Trim Bolt {1257}
1987/06/01
Features And Servicing Of The Various Caterpillar 3161 Governors {1264,1278}
1987/06/01
Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
Additional Information For Installing Fuel Injectors{1290,1257}
1988/06/13
Two 11 mm Injectors Available For Parts Service{1250,1290}
1988/06/20
Replacement Fuel Injector Nozzles With New Nose Cones Available{0706,1254,1290}
1988/07/25
New Rocker Arm Shaft Assembly and Bolts Used{1102}
1988/09/05
Digital Dial Indicator Simplifies Fuel Injection Timing Adjustment{0782,0760,1257,1290}
1988/11/07
One-Piece Tappet (Follower) Used In 11 mm (Type 2) Fuel Injectors{1290}
1988/11/21
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Check Valve Added To Fuel Injection Lines {1274}
1989/05/22
New Connector With An Orifice Added To Fuel Injection Lines Groups To Help Prevent Cavitation{1274}
1989/06/26
Improved Control Rod Assembly Used In Fuel Injection Control Groups{1298}
1989/07/24
New Fuel Injectors Available For Parts Service{1290}
1989/08/28
Fuel Injector Reference For 3500 Family Of Engines{1290}
1989/10/02
New Fuel Injector Assemblies Used{1290}
1989/10/16
Some Fuel Injectors May Be Used In Mixed Sets {1290}
1990/05/21
New 7C9580 Fuel Injector (Type 2) Available To Replace 2W5201 Fuel Injector (Type 1) {1290}
1990/06/11
New "On Engine" Adjustment Procedure For 3161 Woodward Governor {1264,0782}
1990/10/22
Field Replacement Of Spacer To Correct Possible Sticking In Woodward 3161 Governor Electric Shutoff Group{1264}
1990/11/19
Remanufactured Type 1 Fuel Injector Assembly Available For 3500 Family Of Engines Equipped With UG8 Governors {1254,1264}
1991/04/01
New Speed Setting Clutch Group For 3161 Woodward Governors{1265}
1991/05/20
End Clearance Specification Changed For Front Shaft In Fuel Injection Control{1251,1258}
1991/10/14
New And Remanufactured Fuel Injector Reference{1290}
1992/05/18
Modifying Former 2W8888 Rocker Arm Shaft For Use With New 8T7581 Rocker Arm Shaft Bolt{1102}
1992/12/21
New And Remanufactured Fuel Injector Reference {1290}
1993/01/18
New Fuel Injector Group Help Reduce Plunger And Barrel Seizures{1290}
1993/05/31
New 3161 Governor With Improved Fuel Limiter{1264}
1993/09/20
Fuel Dilution In The Engine Oil{1290,1318}
1994/05/16
Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14

Caterpillar Parts SIS Catalog 3508 :

PUMP GP-FUEL INJECTION
7W-2062 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7C-3764 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
7C-2233 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
2W-9579 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
2W-9578 PUMP GP-FUEL INJECTION
PANEL AS-GOVERNOR
1W-7207 PANEL AS-GOVERNOR
MOUNTING GP-WATER SEPARATOR
179-1479 MOUNTING GP-WATER SEPARATOR
MOUNTING GP-GOVERNOR CONTROL
7C-2375 MOUNTING GP-GOVERNOR CONTROL
PUMP GP-FUEL INJECTION
9Y-1796 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-1796 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-6988 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-6988 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-7841 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
9Y-7841 PUMP GP-FUEL INJECTION
PUMP GP-FUEL PRIMING
262-4960 PUMP GP-FUEL PRIMING
PUMP GP-FUEL PRIMING
314-6842 PUMP GP-FUEL PRIMING

Truck sale:

Caterpillar 3508, Stationary Generator Sets, Construction
61,000 
Caterpillar 3508, Stationary Generator Sets, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY
Caterpillar 3508, Stationäre Stromaggregate, Bau-Und Bergbauausrüstung
307.208 
Caterpillar 3508, Stationäre Stromaggregate, Bau-Und Bergbauausrüstung
- Stationary Generator Sets
TOROMONT POWER SYSTEMS
Caterpillar 3508, Industrial engines, Construction
84,962 
Caterpillar 3508, Industrial engines, Construction
- Industrial engines
FINANZAUTO S.A.
Caterpillar 3508, Marine Propulsion / Auxiliary Engines, Construction
 
Caterpillar 3508, Marine Propulsion / Auxiliary Engines, Construction


 
145.548 
Caterpillar 3508 PKGI, transportable stromaggregate, Bau-Und Bergbauausrüstung


Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.