AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

7C-9760 PUMP GP-FUEL TRANSFER 12 VOLT. BOOST FIELD INSTALLATION 3208 TRUCK ENGINE


FUEL SYSTEM
PUMP GP-FUEL TRANSFER
GOVERNOR GP

TRUCK ENGINE 3208 TRUCK ENGINE 51Z
 3208 Truck Engine 51Z55824-UP SEBP1635 3208 51Z   (1982)

FUEL SYSTEM

PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
7C-9760 PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
8N-3569 PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
8N-3569 PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
9N-5458 PUMP GP-FUEL TRANSFER
 

#SEBP16350350
 

7C-9760: PUMP GP-FUEL TRANSFER

7C-9760 PUMP GP-FUEL TRANSFER
12 VOLT. BOOST
FIELD INSTALLATION
i00145452 SEBP1635
7C9760 PUMP GP-FUEL TRANSFER Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7W-7831 Y [1] FILTER GP-PRIMARY FUEL  
2. 7C-9748 [1] PUMP AS-FUEL TRANSFER  
3. 2V-6351 [1] CLIP  
  2V-6353 [1] CLIP  
  Y   SEPARATE ILLUSTRATION
 

#SEBP16350351
 

8N-3569: PUMP GP-FUEL TRANSFER

8N-3569 PUMP GP-FUEL TRANSFER
24 VOLT. BOOST
Type 1
FIELD INSTALLATION
i00525753 SEBP1635
8N3569 PUMP GP-FUEL TRANSFER Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8H-4681 Y [1] FILTER GP-PRIMARY FUEL  
2. 7W-5668 [1] PUMP AS-FUEL TRANSFER  
3. 2V-6351 [1] CLIP (CURVED)  
4. 2V-6353 [1] CLIP  
  Y   SEPARATE ILLUSTRATION
 

#SEBP16350352
 

8N-3569: PUMP GP-FUEL TRANSFER

8N-3569 PUMP GP-FUEL TRANSFER
24 VOLT. BOOST
Type 2
FIELD INSTALLATION
i00145593 SEBP1635
8N3569 PUMP GP-FUEL TRANSFER Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7W-7831 CY [1] FILTER GP-PRIMARY FUEL  
2. 7W-5668 [1] PUMP AS-FUEL TRANSFER  
3. 2V-6351 [1] CLIP  
4. 2V-6353 [1] CLIP  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

#SEBP16350353
 

9N-5458: PUMP GP-FUEL TRANSFER

9N-5458 PUMP GP-FUEL TRANSFER
12 VOLT. BOOST, PROVIDES POSITIVE PRESSURE TO THE SLEEVE METERING FUEL SYSTEM COMPONENTS ON THE SUCTION SIDE OF THE FUEL TRANSFER PUMP
FIELD INSTALLATION
i00145824 SEBP1635
9N5458 PUMP GP-FUEL TRANSFER Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8H-4681 Y [1] FILTER GP-PRIMARY FUEL  
2. 7C-9748 [1] PUMP AS-FUEL TRANSFER  
  Y   SEPARATE ILLUSTRATION
 

#SEBP16350354
 

7C-1455: PUMP GP-GOV & FUEL INJ

7C-1455 PUMP GP-GOV & FUEL INJ
S/N 51Z55824-80833; 51Z80872-UP
i00399488 SEBP1635
7C1455 PUMP GP-GOV & FUEL INJ Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-0509 Y [1] TORQUE CONTROL GP  
2. 4N-0443 [1] PIN-LOAD STOP  
3. 9N-0683 Y [1] SHUTOFF GP-ELECTRICAL  
4. 7C-1510 Y [1] PUMP GP-GOV & FUEL INJ  
  Y   SEPARATE ILLUSTRATION
 

#SEBP16350355
 

7C-1509: PUMP GP-GOV & FUEL INJ

7C-1509 PUMP GP-GOV & FUEL INJ
PART OF 7C-1510 PUMP GP-GOV & FUEL INJ
Type 1
i00399608 SEBP1635
7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-0209 [8] BONNET-VALVE  
2. 9L-9424 [8] SPRING-VALVE  
  7N-5148 [8] VALVE-CHECK (ORIFICED DELIVERY)  
3. 4N-0224 [8] RING-RETAINING  
4. 4N-0218 [8] BUSHING-TERMINAL  
5. 6N-7527 [8] PUMP AS-FUEL INJECTION  
  9N-5862 [1] SPRING-LIFTER  
6. 4N-2728 [1] WASHER-RETAINING  
7. 4N-2685 [8] ROLLER-LIFTER  
8. 6N-6794 [8] LIFTER-PLUNGER  
9. 6F-6672 [8] SEAL-O-RING  
10. 7N-1359 [1] FLANGE  
11. 2M-5471 [2] BOLT  
12. 4N-3088 [1] GASKET-INLET  
13. 7N-1364 [1] FLANGE AS-CHECK VALVE  
14. 1P-2298 [1] VALVE AS  
15. 4N-0975 [1] GASKET-CHECK VALVE  
16. 6N-1716 [1] VALVE AS  
17. 3J-7354 [1] SEAL-O-RING  
1. 0S-1615 [7] BOLT (1/4-20X0.75-IN)  
2. 3J-7354 [1] SEAL-O-RING  
3. 9S-4182 [1] PLUG  
4. 8H-3127 [2] BOLT (1/4-20X0.75-IN)  
5. 9S-9332 [1] FITTING-ELBOW  
6. 124-5939 [1] COVER-FUEL PUMP HOUSING  
7. 6D-3031 [4] SCREW-SOCKET HEAD (8-32X0.375-IN)  
8. 4N-0941 [1] LEVER-LIMITER  
9. 4N-0505 [1] GASKET-HOUSING  
10. 128-2974 [1] HOUSING AS (SHUT-OFF)  
  4N-3713 [1] SEAL-LIP TYPE  
11. 127-7139 [1] GASKET-TOP COVER  
12. 9N-6318 [1] HOUSING AS-PUMP  
  9S-4180 [1] PLUG  
  4J-7533 [1] SEAL-O-RING  
13. 4N-9150 [1] DEFLECTOR-PULSE  
14. 4N-1826 [2] DOWEL  
15. 2D-6392 [2] SEAL-O-RING  
16. 7W-6335 [1] BEARING  
17. 8N-0628 [1] BEARING  
18. 4N-2333 [1] PIN-SPRING  
19. 8N-0984 [8] PIN-SPRING  
20. 4N-5481 [1] STUD  
21. 1P-4001 [1] FITTING  
22. 4N-0556 [1] GASKET-GOVERNOR HOUSING  
23. 4N-0532 [1] GASKET-COVER  
24. 4N-0531 [1] COVER-IDLE SCREW  
25. 6L-1756 [2] BOLT (1/4-20X1.5-IN)  
26. 4N-0938 [1] SHAFT-LEVER  
27. 4N-0940 [1] LEVER-SHUTOFF  
28. 124-5942 [1] SHAFT-SOLENOID  
1. 4N-2773 [1] SHAFT AS-CONTROL  
2. 1D-4716 [1] NUT-FULL (5/16-18-THD)  
3. 4N-2708 [1] SETSCREW  
4. 4N-0528 [1] SHAFT-LEVER  
5. 4N-9828 [1] SHAFT AS-CONTROL  
6. 4N-3922 [1] LEVER AS  
7. 2N-2658 [10] BOLT-SOCKET HEAD (8-32X15.88-MM)  
8. 4N-1763 [8] LEVER-CONTROL  
9. 4N-0563 [1] LEVER-SHAFT  
10. 9L-6807 [1] SHAFT-CONTROL  
11. 4N-1809 [1] LEVER AS-SEAT  
12. 031-0214 [2] BOLT-LOCKING (1/4-20X0.5-IN)  
13. 9M-1311 [1] NUT-JAM (1/4-28-THD)  
14. 6N-4176 [1] SETSCREW  
15. 4N-0445 [1] LEVER-LOAD STOP  
16. 4N-0523 [1] DOWEL-STOP SUPPORT  
17. 2D-6392 [2] SEAL-O-RING  
18. 4N-3329 [2] WASHER (16.25X25.65X0.79-MM)  
19. 6N-7523 [1] WASHER (6.48X11.9X1.57-MM THK)  
20. 8F-8178 [1] BOLT (1/4-20X3.25-IN)  
21. 1D-4533 [3] BOLT (1/4-20X2.25-IN)  
22. 2A-4781 [3] BOLT (1/4-20X2.75-IN)  
23. 8N-3946 [1] HOUSING AS-GOVERNOR  
24. 4N-2333 [1] PIN-SPRING  
25. 8S-6814 [2] PIN  
26. 9L-9503 [1] DOWEL-HOLLOW  
27. 9S-4182 [1] PLUG  
28. 3J-7354 [1] SEAL-O-RING  
29. 8N-3945 [1] BUSHING-TERMINAL  
30. 2W-4037 [1] SEAL-LIP TYPE  
31. 4N-2677 [1] LEVER AS-RISER  
32. 3H-0442 [1] SEAL-O-RING  
33. 2M-7819 [1] RING-RETAINING  
34. 6L-3921 [1] WASHER-SPECIAL  
1. 9F-6641 [4] BOLT (5/16-18X1.25-IN)  
2. 4N-2954 [1] SLEEVE-CAMSHAFT  
3. 4N-1132 [1] BODY AS-TRANSFER PUMP  
4. 8S-6814 [1] PIN  
5. 4N-1584 [1] SEAL-LIP TYPE  
6. 4N-0636 [1] SEAL-LIP TYPE  
7. 8H-9804 [1] SHAFT-PUMP IDLER  
8. 4N-0429 [1] GEAR-PUMP (15-TEETH)  
9. 4N-0406 [1] GEAR-PUMP (10-TEETH)  
10. 5M-6509 [1] SEAL-O-RING  
11. 4N-1767 [1] VALVE-BYPASS (FUEL)  
12. 4N-0605 [1] SPRING  
1. 4N-4276 [1] SEAT-SPRING  
2. 4N-6408 [1] PISTON AS  
3. 4N-6406 [1] RING-SPACER  
4. 4N-6404 [1] RING-RETAINING  
5. 4N-6407 [1] SPOOL-DASHPOT  
6. 6N-2517 [1] SPRING-DASHPOT  
7. 2W-8623 [1] SEAT-SPRING  
8. 4N-0434 [1] RISER-GOVERNOR  
9. 4N-2927 [2] RACE-THRUST BEARING  
  7M-7219 [1] BEARING-THRUST  
10. 4N-2953 [1] RING-LOCK  
11. 4N-3779 [1] KEY-CAMSHAFT  
12. 7C-1508 [1] CAMSHAFT AS  
  7C-1507 [1] CAMSHAFT-FUEL PUMP  
13. 8N-2663 [1] CARRIER-WEIGHT  
14. 8N-2662 [3] BOLT-SOCKET HEAD  
15. 4N-1723 [1] SHIELD-CARRIER  
16. 4N-0425 [3] WEIGHT-GOVERNOR  
17. 4N-0511 [3] DOWEL  
18. 4N-5482 [1] SHAFT-WEIGHT CARRIER  
19. 4N-9019 [1] DOWEL  
20. 9N-5822 [1] WASHER-THRUST  
 

#SEBP16350356
 

7C-1509: PUMP GP-GOV & FUEL INJ

7C-1509 PUMP GP-GOV & FUEL INJ
PART OF 7C-1510 PUMP GP-GOV & FUEL INJ
Type 2
i00399637 SEBP1635
7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme 7C1509 PUMP GP-GOV & FUEL INJ Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-0209 [8] BONNET-VALVE  
2. 9L-9424 [8] SPRING-VALVE  
  7N-5148 [8] VALVE-CHECK (ORIFICED DELIVERY)  
3. 4N-0224 [8] RING-RETAINING  
4. 7W-8120 C [8] BUSHING-TERMINAL  
5. 6N-7527 [8] PUMP AS-FUEL INJECTION  
  9N-5862 [1] SPRING-LIFTER  
6. 4N-2728 [1] WASHER-RETAINING  
7. 4N-2685 [8] ROLLER-LIFTER  
8. 6N-6794 [8] LIFTER-PLUNGER  
9. 6F-6672 [8] SEAL-O-RING  
10. 6N-1716 [1] VALVE AS  
11. 3J-7354 [1] SEAL-O-RING  
12. 2M-5471 [2] BOLT  
13. 9Y-0546 [1] FLANGE AS  
14. 1P-2298 [1] VALVE AS  
15. 4N-0975 [1] GASKET-CHECK VALVE  
16. 0S-1615 [7] BOLT (1/4-20X0.75-IN)  
17. 3J-7354 [1] SEAL-O-RING  
18. 9S-4182 [1] PLUG  
19. 8H-3127 [2] BOLT (1/4-20X0.75-IN)  
20. 9S-9332 [1] FITTING-ELBOW  
21. 124-5939 [1] COVER-FUEL PUMP HOUSING  
22. 6D-3031 [4] SCREW-SOCKET HEAD (8-32X0.375-IN)  
23. 4N-0941 [1] LEVER-LIMITER  
24. 4N-0505 [1] GASKET-HOUSING  
25. 128-2974 [1] HOUSING AS (SHUT-OFF)  
  4N-3713 [1] SEAL-LIP TYPE  
26. 127-7139 [1] GASKET-TOP COVER  
27. 9N-6318 [1] HOUSING AS-PUMP  
  9S-4180 [1] PLUG  
  4J-7533 [1] SEAL-O-RING  
28. 4N-9150 [1] DEFLECTOR-PULSE  
29. 4N-1826 [2] DOWEL  
30. 2D-6392 [2] SEAL-O-RING  
31. 7W-6335 [1] BEARING  
32. 8N-0628 [1] BEARING  
33. 4N-2333 [1] PIN-SPRING  
34. 8N-0984 [8] PIN-SPRING  
35. 4N-5481 [1] STUD  
36. 1P-4001 [1] FITTING  
37. 4N-0556 [1] GASKET-GOVERNOR HOUSING  
38. 4N-0532 [1] GASKET-COVER  
39. 4N-0531 [1] COVER-IDLE SCREW  
40. 6L-1756 [2] BOLT (1/4-20X1.5-IN)  
41. 170-5705 [1] SHAFT-SHUTOFF  
42. 4N-0940 [1] LEVER-SHUTOFF  
43. 124-5942 [1] SHAFT-SOLENOID  
44. 4N-2773 [1] SHAFT AS-CONTROL  
45. 5S-0003 [1] NUT (5/16-18-THD)  
46. 4N-2708 [1] SETSCREW  
47. 4N-0528 [1] SHAFT-LEVER  
48. 4N-9828 [1] SHAFT AS-CONTROL  
49. 4N-3922 [1] LEVER AS  
50. 2N-2658 [10] BOLT-SOCKET HEAD (8-32X15.88-MM)  
51. 4N-1763 [8] LEVER-CONTROL  
52. 126-4144 [1] LEVER-SHAFT  
53. 124-5941 [1] SHAFT-CONTROL  
54. 7C-6201 C [1] LEVER-SEAT  
55. 7X-2395 C [1] BOLT-LOCKING  
56. 6F-0612 [1] NUT-JAM (1/4-28-THD)  
57. 6N-4176 [1] SETSCREW  
58. 4N-0445 [1] LEVER-LOAD STOP  
59. 4N-0523 [1] DOWEL-STOP SUPPORT  
60. 2D-6392 [2] SEAL-O-RING  
61. 4N-3329 [2] WASHER (16.25X25.65X0.79-MM)  
62. 6N-7523 [1] WASHER (6.48X11.9X1.57-MM THK)  
63. 8F-8178 [1] BOLT (1/4-20X3.25-IN)  
64. 1D-4533 [3] BOLT (1/4-20X2.25-IN)  
65. 2A-4781 [3] BOLT (1/4-20X2.75-IN)  
66. 8N-3946 [1] HOUSING AS-GOVERNOR  
67. 4N-2333 [1] PIN-SPRING  
68. 8S-6814 [2] PIN  
69. 9L-9503 [1] DOWEL-HOLLOW  
70. 9S-4182 [1] PLUG  
71. 3J-7354 [1] SEAL-O-RING  
72. 8N-3945 [1] BUSHING-TERMINAL  
73. 2W-4037 [1] SEAL-LIP TYPE  
74. 9Y-4966 [1] VALVE AS-RELIEF  
  2D-6392 [1] SEAL-O-RING  
75. 3H-0442 [1] SEAL-O-RING  
76. 2M-7819 [1] RING-RETAINING  
77. 6L-3921 [1] WASHER-SPECIAL  
78. 7C-6202 C [1] LEVER  
79. 128-7347 [1] LEVER AS-RISER  
80. 9F-6641 [4] BOLT (5/16-18X1.25-IN)  
81. 4N-2954 [1] SLEEVE-CAMSHAFT  
82. 4N-1132 [1] BODY AS-TRANSFER PUMP  
83. 8S-6814 [1] PIN  
84. 4N-1584 [1] SEAL-LIP TYPE  
85. 4N-0636 [1] SEAL-LIP TYPE  
86. 8H-9804 [1] SHAFT-PUMP IDLER  
87. 4N-0429 [1] GEAR-PUMP (15-TEETH)  
88. 4N-0406 [1] GEAR-PUMP (10-TEETH)  
89. 5M-6509 [1] SEAL-O-RING  
90. 4N-1767 [1] VALVE-BYPASS (FUEL)  
91. 4N-0605 [1] SPRING  
92. 4N-4276 [1] SEAT-SPRING  
93. 4N-6408 [1] PISTON AS  
94. 4N-6406 [1] RING-SPACER  
95. 4N-6404 [1] RING-RETAINING  
96. 4N-6407 [1] SPOOL-DASHPOT  
97. 6N-2517 [1] SPRING-DASHPOT  
98. 2W-8623 [1] SEAT-SPRING  
99. 4N-0434 [1] RISER-GOVERNOR  
100. 4N-2927 [2] RACE-THRUST BEARING  
  7M-7219 [1] BEARING-THRUST  
101. 4N-2953 [1] RING-LOCK  
102. 4N-3779 [1] KEY-CAMSHAFT  
103. 7C-1508 [1] CAMSHAFT AS  
  7C-1507 [1] CAMSHAFT-FUEL PUMP  
104. 8N-2663 [1] CARRIER-WEIGHT  
105. 8N-2662 [3] BOLT-SOCKET HEAD  
106. 4N-1723 [1] SHIELD-CARRIER  
107. 4N-0425 [3] WEIGHT-GOVERNOR  
108. 4N-0511 [3] DOWEL  
109. 4N-5482 [1] SHAFT-WEIGHT CARRIER  
110. 4N-9019 [1] DOWEL  
111. 9N-5822 [1] WASHER-THRUST  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP16350357
 

7C-1510: PUMP GP-GOV & FUEL INJ

7C-1510 PUMP GP-GOV & FUEL INJ
PART OF 7C-1455 PUMP GP-GOV & FUEL INJ
i00399645 SEBP1635
7C1510 PUMP GP-GOV & FUEL INJ Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-9226 [1] SPRING (OUTER)(OUTER)  
2. 4N-5663 [1] SPRING (INNER)(INNER)  
3. 4N-0527 [1] SPRING  
4. 7L-8070 [2] BOLT  
5. 4F-7957 [2] BOLT (1/4-20X0.875-IN)  
6. 3L-5987 [1] COVER  
6A. 6L-5773 [1] GASKET  
7. 7C-1509 Y [1] PUMP GP-GOV & FUEL INJ  
8. 165-6475 [1] COVER  
9. 6N-0412 [1] SCREW AS-MACHINE  
9A. 4B-2042 [1] NUT (8-32-THD)  
9B. 3B-4501 [1] LOCKWASHER  
9C. 1P-7326 [1] WASHER (4.32X9.52X1.52-MM THK)  
9D. 8F-1326 [1] WASHER (4.2X9.5X0.8-MM THK)  
10. 3K-8460 [1] PLUG  
10A. 1J-9671 [1] SEAL-O-RING  
11. 166-0368 [1] GASKET  
  Y   SEPARATE ILLUSTRATION
 

#SEBP16350358
 

7C-2291: PUMP GP-GOV & FUEL INJ

7C-2291 PUMP GP-GOV & FUEL INJ
S/N 51Z55824-70903
i00402819 SEBP1635
7C2291 PUMP GP-GOV & FUEL INJ Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-0509 Y [1] TORQUE CONTROL GP  
2. 4N-0443 [1] PIN-LOAD STOP  
3. 9N-0683 Y [1] SHUTOFF GP-ELECTRICAL  
4. 7C-2292 Y [1] PUMP GP-GOV & FUEL INJ  
  Y   SEPARATE ILLUSTRATION
 

#SEBP16350359
 

7C-2292: PUMP GP-GOV & FUEL INJ

7C-2292 PUMP GP-GOV & FUEL INJ
S/N 51Z55824-70903
PART OF 7C-2291 PUMP GP-GOV & FUEL INJ
i00402822 SEBP1635
7C2292 PUMP GP-GOV & FUEL INJ Parts scheme
  For full view, you need register

Parts for your 3208 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-6119 [1] SPRING (OUTER)  
2. 4N-5663 [1] SPRING (INNER)(INNER)  
3. 4N-0527 [1] SPRING  
4. 2M-5471 [2] BOLT  
5. 4F-7957 [2] BOLT (1/4-20X0.875-IN)  
6. 3L-5987 [1] COVER  
  6L-5773 [1] GASKET  
7. 7C-2293 Y [1] PUMP GP-GOV & FUEL INJ  
8. 4N-1591 [1] COVER AS-SPRING HOUSING  
  6N-0411 [1] COVER-TORQUE SPRING  
9. 6N-0412 [1] SCREW AS-MACHINE  
  4B-2042 [1] NUT (8-32-THD)  
  3B-4501 [1] LOCKWASHER  
  1P-7326 [1] WASHER (4.32X9.52X1.52-MM THK)  
  8F-1326 [1] WASHER (4.2X9.5X0.8-MM THK)  
10. 2P-3200 [1] BOLT-WASHER HEAD  
  1J-9671 [1] SEAL-O-RING  
11. 4N-0508 [1] GASKET-COVER  
  Y   SEPARATE ILLUSTRATION
 

Information:

Truck Engine News
New Governor Spring Available For Specific Engine Applications
1981/03/06
Clean Electrical Contacts In Exhaust Gas Recirculation (e.g.r.) Switch Group And Cover Assembly Before Installation
1981/04/09
Electrical Information For Egr (exhaust Gas Recirculation) Systems On 3208 Truck Engines So Equipped
1981/04/09
Check All Settings When Fuel Injection Pump Group Is Installed
1981/04/09
New 6V3060 EGR System Tester Group Available
1981/05/12
Some Parts Books And Microfiche Show Wrong Governor And Fuel Pump Drive Groups For Specific Engines
1981/08/18
Bent Lever For Fuel Shut-off Solenoid Can Cause Low Engine Performance
1982/02/17
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/03/31
New Gasket Used In Governor And Fuel Injection Pump Group
1982/03/31
FT1698 Driver Can Be Used For Reconditioning Of Governor Housing
1982/10/27
New Seal Used On Governor Control Shaft
1982/12/08
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1983/12/21
Sleeve Can Be Used For Reconditioning The Mounting Bore For The Fuel Pump Housing In The Cylinder Block
1983/12/21
Governor Flyweight Shield No Longer Used In New Scroll Fuel Systems
1985/01/01
Anti-seize Compound And/or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/11/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps
1987/11/01
Check Valve Added To Keep Air From Entering Fuel System
1988/10/01
Governor Springs For Sleeve Metering Fuel Systems
1990/05/01
New Spring Used In Governor Control Groups
1992/04/01
New Hold-Down Bolts For The Sleeve Metering Fuel System (SMFS) Governor Housing {1251}
1996/09/01
Engine News
A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing
1979/01/24
Improvements Made To Fuel Injection Pump And Governor Group
1979/03/14
New Pistons And Timing Advance Unit Give Better Emissions Control And Easier Starts
1979/04/04
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.
1979/05/09
Timing Advance Mechanism Used In Certain 3208 Truck Engines In Ford Trucks
1979/08/08
New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group
1979/08/22
Important: Use Only 12 Volts Direct Current To Boost Start 3208 Truck Engines Equipped With Exhaust Gas Recirculation Systems
1980/04/09
Drains In New Fuel Injection Pump Housing And Governor Housing Prevent Possible Corrosion And Freezing Damage
1977/03/15
Service Tools For Low Emission Truck Engines With EGR
1977/06/29
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Correct Adjustment Of The Governor Control Linkage In Truck Engines Is Necessary To Prevent Low Power
1978/04/05
9N3700 Or 9N3299 Nozzle Assemblies Must Be Used On 3208 Engines That Are Equipped With Exhaust Gas Recirculation (EGR)
1978/04/05
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time
1978/07/05
Improved Guide Pin For Fuel Injection Pump Lifters
1978/08/30
New Control Cover Gives Better Control Of Exhaust Gas Recirculation System
1978/11/15
New Fuel Injection Nozzles Are Used In 3208 Truck Engines When Equipped With EGR
1978/11/15
A Washer With Closer Tolerances Is Now Used In The Governor And Fuel Pump Drive Group
1978/12/13
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N628 Bearing{7551, 1253}
Installation Of 8N628 Bearing{7551, 1253}
Installation Of 8N3569 (24V) Or 9N5458 (12V) Fuel Boost Pump Group{1250}
Installation Of 8N3569 (24V) Or 9N5458 (12V) Fuel Boost Pump Group{1250}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Installation Of 1W4793 Governor Spring (High Idle){1264, 1265}
Installation Of 1W4793 Governor Spring (High Idle){1264, 1265}
Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253}
Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Service Letter-NACD
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Fuel Injection Pump
3208 TRUCK ENGINE
Governor
3208 TRUCK ENGINE
Fuel Transfer Pump
3208 TRUCK ENGINE
Drive Gear For The Injection Pump
3208 TRUCK ENGINE
Automatic Timing Advance Unit<BR> (3&deg; and 5&deg; Units)
3208 TRUCK ENGINE
Automatic Timing Advance Unit<BR> 3&deg; For EGR Engine
3208 TRUCK ENGINE
AUTOMATIC TIMING ADVANCE UNIT<BR> 3&deg; FOR LOW EMISSION ENGINE
3208 TRUCK ENGINE
Tool Operating Manual
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
Service Letter-China
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Service Letter-Asia
Reuse And Salvage Guidelines
Reuse and Salvage of New Scroll Fuel Systems (NSFS) for 3200, 3300, & 3400 Engines {1250, 1256}
Reuse and Salvage of New Scroll Fuel Systems (NSFS) for 3200, 3300, & 3400 Engines {1250, 1256}
Service Letter-APD
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Disassembly and Assembly
Fuel Injection Pump Housing And Governor
3208 TRUCK ENGINE
Check Valve And Bypass Valve
3208 TRUCK ENGINE
Fuel Injection Pumps
3208 TRUCK ENGINE
Fuel Transfer Pump
3208 TRUCK ENGINE
Fuel Injection Pump Housing And Governor
3208 TRUCK ENGINE
Governor
3208 TRUCK ENGINE
Fuel Injection Pump Housing
3208 TRUCK ENGINE
Fuel Injection Pump Housing (With Thrust Washer)
3208 TRUCK ENGINE
Automatic Timing Advance
3208 TRUCK ENGINE
Service Magazine
New Check Valve Used In Fuel Injection Pump Assembly{1251}
1980/05/26
New Governor Spring Available For Specific Engine Applications{1264,1265}
1981/02/23
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23
Fuel Pressure Relief Valve Is Shown Inverted (Wrong End Up) In Parts Book Illustrations {1253,1286}
1981/03/23
Check All Settings When Fuel Injection Pump Group Is Installed{1286,1264,1251,1253}
1981/03/30
Some Parts Books And Microfiche Show Wrong Governor And Fuel Pump Drive Groups For Specific Engines{1288,0374}
1981/06/29
Certification Film Necessary On Engines Adjusted For High Altitude Operation{7557,1251,1257,1264}
1981/08/10
FT1632 Bolt Used During Removal Of Sleeve From Sleeve Metering Fuel System{0621,1251,1253}
1981/08/31
Thrust Washer Used In Pump Housing For Sleeve Metering Fuel System{1253,1286}
1981/08/31
Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01
New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01
Modification Of 2P8315 Bracket Assembly{0652,1286}
1982/08/16
FT1698 Driver Can Be Used For Reconditioning Of Governor Housing{0626,0665,1264,1286}
1982/10/18
New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Sleeve Can Be Used For Reconditioning The Mounting Bore For The Fuel Pump Housing In The Cylinder Block{1201}
1983/11/21
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1983/12/05
Changes To Naturally Aspirated Truck Engines For 1985{1000,1200,1214,1218,1250,1251,1254}
1985/04/08
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Drains In New Fuel Injection Pump Housing And Governor Housing Prevent Possible Corrosion And Freezing Damage{1286}
1977/03/07
Changes To The Injection Pump And The Fuel Setting{1251,1257}
1977/09/19
Washer Removed From Variable Timing Unit{1206,1272}
1977/10/03
Improved Fuel Priming Pump Used{1258}
1987/04/20
Four More Remanufactured Fuel Pump And Governor Groups Available {1286}
1987/09/14
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps{1251,1254}
1987/11/23
Correct Adjustment Of The Governor Control Linkage In Truck Engines Is Necessary To Prevent Low Power{1265,1269}
1978/03/27
Stronger Fuel Inlet Flanges Prevent Parts Damage And Keeps Air Out Of The Fuel System{1253}
1978/05/15
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time{1286,1256,1251}
1978/07/03
Improved Guide Pin For Fuel Injection Pump Lifters{1251}
1978/08/21
New Camshaft Rear Bearing For The Sleeve Metering Fuel System{1253}
1978/09/04
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
A Washer With Closer Tolerances Is Now Used In The Governor And Fuel Pump Drive Group{1288,7462}
1978/11/20
Check Valve Added To Keep Air From Entering Fuel System {1264}
1988/10/03
A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing{0626}
1979/01/08
Improvements Made To Fuel Injection Pump And Governor Group{1253,1281,1286}
1979/03/05
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.{1253}
1979/05/07
Two Fuel Pressure Pumps Are Available To Increase Fuel Pressure{1250,1295}
1979/05/14
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}
1979/08/27
Governor Springs For Sleeve Metering Fuel Systems {1264}
1990/05/21
New Spring Used In Governor Control Groups{1265}
1992/04/20

Caterpillar Parts SIS Catalog 3208 :

PUMP GP-FUEL PRM & WATER SEP
4W-4024 PUMP GP-FUEL PRM & WATER SEP
PUMP GP-FUEL PRIMING
4N-4314 PUMP GP-FUEL PRIMING
9N-2936 MOUNTING GP-FUEL FILTER
LINES GP-FUEL INJECTION
9Y-0301 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9Y-0300 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9Y-0299 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9Y-0298 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
9N-3880 LINES GP-FUEL INJECTION
PUMP GP-FUEL TRANSFER
8N-3569 PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
8N-3569 PUMP GP-FUEL TRANSFER
PUMP GP-FUEL TRANSFER
9N-5458 PUMP GP-FUEL TRANSFER
PUMP GP-GOV & FUEL INJ
7C-1455 PUMP GP-GOV & FUEL INJ
PUMP GP-GOV & FUEL INJ
7C-1509 PUMP GP-GOV & FUEL INJ
PUMP GP-GOV & FUEL INJ
7C-1509 PUMP GP-GOV & FUEL INJ
PUMP GP-GOV & FUEL INJ
7C-1510 PUMP GP-GOV & FUEL INJ
PUMP GP-GOV & FUEL INJ
7C-2291 PUMP GP-GOV & FUEL INJ

Truck sale:

 
11,500 
Caterpillar D3208EP, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY
CATERPILLAR 3208 1993
 
CATERPILLAR 3208 1993
- STATIONARY - DIESEL
WAGNER EQUIPMENT CO
United States
CATERPILLAR 3208 2004
 
CATERPILLAR 3208 2004
- STATIONARY GENERATOR SETS
EMPRESAS MATCO, S.A. DE C.V.
Sufragio Efectivo Norte 870 - Obregón -
1998 CAT 3208
USD $19,000 
1998 CAT 3208

Galactic Liquidation LLC
1990 CAT 3208
 
1990 CAT 3208

Ken Porter Auctions
Carson, California
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.