AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

3208 Truck Engine Turbocharged 02Z40745-UP ELECTRICAL AND STARTING SYSTEM Caterpillar SIS



TRUCK ENGINE 3208 TRUCK ENGINE 02Z
 3208 Truck Engine Turbocharged 02Z40745-UP SEBP1776 3208 02Z   (1980)

Parts group 3208:

  For full view, you need register
ELECTRICAL AND STARTING SYSTEM
ALTERNATOR GP-CHARGING
MOUNTING GP-ALTERNATOR
4N-9315 MOUNTING GP-ALTERNATOR
4N-9315 MOUNTING GP-ALTERNATOR
S/N 02Z40745-66492
FOR USE WITH AIR COMPRESSOR, CUSTOMER SUPPLIED RADIATOR, HIGH MOUNTED FAN
CANNOT BE USED WITH @@@@@ 4N-9314@@@@@
ALSO AN ATTACHMENT
MOUNTING GP-ALTERNATOR
8N-6129 MOUNTING GP-ALTERNATOR
8N-6129 MOUNTING GP-ALTERNATOR
FOR USE WITH MOUNTING ALTERNATORS WITHOUT AIR COMPRESSOR
AN ATTACHMENT
PULLEY GP-ALTERNATOR
114-4666 PULLEY GP-ALTERNATOR
114-4666 PULLEY GP-ALTERNATOR
FOR USE WITH 9Y-5165 DRIVE GP-FAN
AN ATTACHMENT
ALTERNATOR GP-CHARGING
3T-6352 ALTERNATOR GP-CHARGING
3T-6352 ALTERNATOR GP-CHARGING
24-VOLT, 35-AMPERE
PART OF 6N-9294 ALTERNATOR GP-CHARGING
FIELD REPLACEMENT ORDER @@@@@ 6N-9294@@@@@
AN ATTACHMENT
ALTERNATOR GP-CHARGING
4N-7256 ALTERNATOR GP-CHARGING
4N-7256 ALTERNATOR GP-CHARGING
12 VOLT, 60 AMPERE
AN ATTACHMENT
6N-9294 ALTERNATOR GP-CHARGING
6N-9294 ALTERNATOR GP-CHARGING
24-VOLT, 35-AMPERE
Type 1
FIELD REPLACEMENT FOR @@@@@ 9G-4574@@@@@, @@@@@ 3T-6352@@@@@
AN ATTACHMENT
ALTERNATOR GP-CHARGING
6N-9294 ALTERNATOR GP-CHARGING
6N-9294 ALTERNATOR GP-CHARGING
24-VOLT, 35-AMPERE
Type 2
FIELD REPLACEMENT FOR @@@@@ 9G-4574@@@@@, @@@@@ 3T-6352@@@@@
AN ATTACHMENT
ALTERNATOR GP-CHARGING
7C-5796 ALTERNATOR GP-CHARGING
7C-5796 ALTERNATOR GP-CHARGING
24 VOLT, 40 AMPERE
AN ATTACHMENT
ALTERNATOR GP-CHARGING
7G-7889 ALTERNATOR GP-CHARGING
7G-7889 ALTERNATOR GP-CHARGING
12-VOLT, 60-AMPERE
AN ATTACHMENT
ALTERNATOR GP-CHARGING
7N-9720 ALTERNATOR GP-CHARGING
7N-9720 ALTERNATOR GP-CHARGING
24-VOLT, 35-AMPERE
PART OF 6N-9294 ALTERNATOR GP-CHARGING
AN ATTACHMENT
ALTERNATOR GP-CHARGING
8T-9700 ALTERNATOR GP-CHARGING
8T-9700 ALTERNATOR GP-CHARGING
12 VOLT, 55 AMPERE
PART OF 4N-7256 ALTERNATOR GP-CHARGING
AN ATTACHMENT
ALTERNATOR GP-CHARGING
9G-4574 ALTERNATOR GP-CHARGING
9G-4574 ALTERNATOR GP-CHARGING
24-VOLT, 35-AMPERE
PART OF 6N-9294 ALTERNATOR GP-CHARGING
FIELD REPLACEMENT ORDER @@@@@ 6N-9294@@@@@
AN ATTACHMENT
ALTERNATOR GP-CHARGING
9W-3043 ALTERNATOR GP-CHARGING
9W-3043 ALTERNATOR GP-CHARGING
24-VOLT, 52-AMPERE
PART OF 7C-5796 ALTERNATOR GP-CHARGING
AN ATTACHMENT
SHUTOFF GP
SHUTOFF GP-ELECTRICAL
7W-7260 SHUTOFF GP-ELECTRICAL
7W-7260 SHUTOFF GP-ELECTRICAL
S/N 02Z40745-65154
PART OF 7C-8960, 9Y-4547 PUMP GP-GOV & FUEL INJ
SHUTOFF GP-ELECTRICAL
9G-7693 SHUTOFF GP-ELECTRICAL
9G-7693 SHUTOFF GP-ELECTRICAL
12 VOLT. ENERGIZE TO SHUT-OFF
AN ATTACHMENT
SHUTOFF GP-ELECTRICAL
9N-0683 SHUTOFF GP-ELECTRICAL
9N-0683 SHUTOFF GP-ELECTRICAL
12 VOLT
PART OF 7C-8931, 7C-8962, 7C-8964, 7C-8966, 7C-8968, 7C-8970, 7E-9889, 9Y-0592, 9Y-4838 PUMP GP-GOV & FUEL INJ
FIELD REPLACEMENT FOR @@@@@ 7C-8931@@@@@, @@@@@ 7C-8962@@@@@, @@@@@ 7C-8964@@@@@
SOLENOID GP-SHUTOFF
4N-9314 SOLENOID GP-SHUTOFF
4N-9314 SOLENOID GP-SHUTOFF
24-VOLT
AN ATTACHMENT
SOLENOID GP-SHUTOFF
6N-3749 SOLENOID GP-SHUTOFF
6N-3749 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9988 SOLENOID GP-SHUTOFF
6N-9987 SOLENOID GP-SHUTOFF
6N-9987 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
24 VOLT
PART OF 7W-7260 SHUTOFF GP-ELECTRICAL, 4N-9314 SOLENOID GP-SHUTOFF
FIELD REPLACEMENT FOR @@@@@ 7C-8960@@@@@
ALSO AN ATTACHMENT
6N-9988 SOLENOID GP-SHUTOFF
6N-9988 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 9N-0683 SHUTOFF GP-ELECTRICAL
SOLENOID GP-SHUTOFF
6T-4126 SOLENOID GP-SHUTOFF
6T-4126 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
24-VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
ALSO AN ATTACHMENT
SOLENOID GP-SHUTOFF
6T-4750 SOLENOID GP-SHUTOFF
6T-4750 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9988 SOLENOID GP-SHUTOFF
SOLENOID GP-SHUTOFF
6T-6121 SOLENOID GP-SHUTOFF
6T-6121 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9988 SOLENOID GP-SHUTOFF
SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
AN ATTACHMENT
SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
12 VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
ALSO AN ATTACHMENT
SOLENOID GP-SHUTOFF
7N-8884 SOLENOID GP-SHUTOFF
7N-8884 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
24-VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
ALSO AN ATTACHMENT
SOLENOID GP-SHUTOFF
9G-8179 SOLENOID GP-SHUTOFF
9G-8179 SOLENOID GP-SHUTOFF
24 VOLT. ENERGIZE TO SHUT-OFF
AN ATTACHMENT
SOLENOID GP
SOLENOID GP-FUEL RATIO CONTROL
1W-3769 SOLENOID GP-FUEL RATIO CONTROL
1W-3769 SOLENOID GP-FUEL RATIO CONTROL
AN ATTACHMENT
SOLENOID GP-SHUTOFF
4N-9314 SOLENOID GP-SHUTOFF
4N-9314 SOLENOID GP-SHUTOFF
24-VOLT
AN ATTACHMENT
SOLENOID GP-SHUTOFF
6N-3749 SOLENOID GP-SHUTOFF
6N-3749 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9988 SOLENOID GP-SHUTOFF
6N-9987 SOLENOID GP-SHUTOFF
6N-9987 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
24 VOLT
PART OF 7W-7260 SHUTOFF GP-ELECTRICAL, 4N-9314 SOLENOID GP-SHUTOFF
FIELD REPLACEMENT FOR @@@@@ 7C-8960@@@@@
ALSO AN ATTACHMENT
6N-9988 SOLENOID GP-SHUTOFF
6N-9988 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 9N-0683 SHUTOFF GP-ELECTRICAL
SOLENOID GP-SHUTOFF
6T-4126 SOLENOID GP-SHUTOFF
6T-4126 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
24-VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
ALSO AN ATTACHMENT
SOLENOID GP-SHUTOFF
6T-4750 SOLENOID GP-SHUTOFF
6T-4750 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9988 SOLENOID GP-SHUTOFF
SOLENOID GP-SHUTOFF
6T-6121 SOLENOID GP-SHUTOFF
6T-6121 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9988 SOLENOID GP-SHUTOFF
SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
12 VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
AN ATTACHMENT
SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
6T-6122 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
12 VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
ALSO AN ATTACHMENT
SOLENOID GP-SHUTOFF
7N-8884 SOLENOID GP-SHUTOFF
7N-8884 SOLENOID GP-SHUTOFF
S/N 02Z40745-65154
24-VOLT
PART OF 6N-9987 SOLENOID GP-SHUTOFF
ALSO AN ATTACHMENT
SOLENOID GP-SHUTOFF
9G-8179 SOLENOID GP-SHUTOFF
9G-8179 SOLENOID GP-SHUTOFF
24 VOLT. ENERGIZE TO SHUT-OFF
AN ATTACHMENT
STARTING MOTOR GP
STARTING MOTOR GP-ELECTRIC
106-8552 STARTING MOTOR GP-ELECTRIC
106-8552 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 6V-5227 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
STARTING MOTOR GP-ELECTRIC
207-1527 STARTING MOTOR GP-ELECTRIC
207-1527 STARTING MOTOR GP-ELECTRIC
12-VOLT
PART OF 2N-3538 STARTING MOTOR GP-ELECTRIC
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
207-1543 STARTING MOTOR GP-ELECTRIC
207-1543 STARTING MOTOR GP-ELECTRIC
S/N 02Z67071-UP
24 VOLT
PART OF 4N-9312 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@207-1560@@@@@
AN ATTACHMENT
207-1560 STARTING MOTOR GP-ELECTRIC
207-1560 STARTING MOTOR GP-ELECTRIC
24-VOLT
FIELD REPLACEMENT FOR @@@@@207-1561@@@@@, @@@@@ 6V-5538@@@@@, @@@@@ 6V-5227@@@@@, @@@@@207-1543@@@@@
STARTING MOTOR GP-ELECTRIC
207-1561 STARTING MOTOR GP-ELECTRIC
207-1561 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 207-1560 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@207-1560@@@@@
STARTING MOTOR GP-ELECTRIC
2N-3538 STARTING MOTOR GP-ELECTRIC
2N-3538 STARTING MOTOR GP-ELECTRIC
S/N 02Z40745-57112
12 VOLT
FOR USE WITH #2 FLYWHEEL HOUSING
ALSO AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
2N-3538 STARTING MOTOR GP-ELECTRIC
2N-3538 STARTING MOTOR GP-ELECTRIC
12 VOLT
FOR USE WITH #2 FLYWHEEL HOUSING
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
3T-2652 STARTING MOTOR GP-ELECTRIC
3T-2652 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 4N-9312 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
AN ATTACHMENT
3T-2657 STARTING MOTOR GP-ELECTRIC
3T-2657 STARTING MOTOR GP-ELECTRIC
S/N 02Z40745-57112
12 VOLT
PART OF 2N-3538 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-4031@@@@@
ALSO AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
3T-6305 STARTING MOTOR GP-ELECTRIC
3T-6305 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 4N-3181 STARTING MOTOR GP-ELECTRIC
Type 1
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
STARTING MOTOR GP-ELECTRIC
3T-6305 STARTING MOTOR GP-ELECTRIC
3T-6305 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 4N-3181 STARTING MOTOR GP-ELECTRIC
Type 2
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
4N-3181 STARTING MOTOR GP-ELECTRIC
4N-3181 STARTING MOTOR GP-ELECTRIC
24-VOLT
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
FIELD REPLACEMENT FOR @@@@@ 7T-0798@@@@@
STARTING MOTOR GP-ELECTRIC
4N-9312 STARTING MOTOR GP-ELECTRIC
4N-9312 STARTING MOTOR GP-ELECTRIC
24 VOLT
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
4N-9312 STARTING MOTOR GP-ELECTRIC
4N-9312 STARTING MOTOR GP-ELECTRIC
S/N 02Z40745-67070
24 VOLT
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
4N-9312 STARTING MOTOR GP-ELECTRIC
4N-9312 STARTING MOTOR GP-ELECTRIC
S/N 02Z67071-UP
24 VOLT
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
6V-4031 STARTING MOTOR GP-ELECTRIC
6V-4031 STARTING MOTOR GP-ELECTRIC
12 VOLT
FIELD REPLACEMENT FOR @@@@@ 3T-2657@@@@@
FIELD INSTALLATION
6V-4451 STARTING MOTOR GP-ELECTRIC
6V-4451 STARTING MOTOR GP-ELECTRIC
S/N 02Z40745-67070
24 VOLT
PART OF 4N-9312 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
6V-4454 STARTING MOTOR GP-ELECTRIC
6V-4454 STARTING MOTOR GP-ELECTRIC
S/N 02Z40745-67070
24 VOLT
PART OF 6V-4451 STARTING MOTOR GP-ELECTRIC
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
6V-4458 STARTING MOTOR GP-ELECTRIC
6V-4458 STARTING MOTOR GP-ELECTRIC
S/N 02Z40745-67070
24 VOLT
PART OF 6V-4451 STARTING MOTOR GP-ELECTRIC
AN ATTACHMENT
6V-5227 STARTING MOTOR GP-ELECTRIC
6V-5227 STARTING MOTOR GP-ELECTRIC
24-VOLT
FIELD REPLACEMENT ORDER @@@@@207-1560@@@@@
FIELD REPLACEMENT FOR @@@@@ 3T-2652@@@@@, @@@@@ 6V-4451@@@@@, @@@@@ 7T-0798@@@@@, @@@@@ 4N-3181@@@@@, @@@@@ 3T-6305@@@@@, @@@@@ 6V-5537@@@@@, @@@@@ 6V-5538@@@@@, @@@@@106-8552@@@@@, @@@@@ 9X-4447@@@@@, @@@@@ 8C-3651@@@@@, @@@@@ 8C-3647@@@@@
STARTING MOTOR GP-ELECTRIC
6V-5537 STARTING MOTOR GP-ELECTRIC
6V-5537 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 6V-5227 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
STARTING MOTOR GP-ELECTRIC
6V-5538 STARTING MOTOR GP-ELECTRIC
6V-5538 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 6V-5227 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@207-1560@@@@@
STARTING MOTOR GP-ELECTRIC
7T-0798 STARTING MOTOR GP-ELECTRIC
7T-0798 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 3T-2652 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 4N-3181@@@@@, @@@@@ 6V-5227@@@@@
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
8C-3643 STARTING MOTOR GP-ELECTRIC
8C-3643 STARTING MOTOR GP-ELECTRIC
S/N 02Z40745-57112
12 VOLT
PART OF 3T-2657 STARTING MOTOR GP-ELECTRIC
ALSO AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
8C-3647 STARTING MOTOR GP-ELECTRIC
8C-3647 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 3T-2652 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
AN ATTACHMENT
STARTING MOTOR GP-ELECTRIC
8C-3651 STARTING MOTOR GP-ELECTRIC
8C-3651 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 4N-3181 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@
STARTING MOTOR GP-ELECTRIC
9X-4447 STARTING MOTOR GP-ELECTRIC
9X-4447 STARTING MOTOR GP-ELECTRIC
24-VOLT
PART OF 4N-3181 STARTING MOTOR GP-ELECTRIC
FIELD REPLACEMENT ORDER @@@@@ 6V-5227@@@@@

Information:

(For parts list, see above)

Truck Engine News
Brushless Alternators May Not Charge In Certain Conditions
1986/07/01
New Alternator Group Used In Charging Alternator Groups
1987/09/01
Repair Parts Available for Alternator R-Terminal {1405}
2000/12/01
Harness Repair of Alternator R-Terminal Connector {1405}
2000/12/01
Cat<SUP>&reg;</SUP> Reman Announces the Availability of Additional Engine Components for Certain Truck Engine Applications {1052, 108F, 1210, 1265, 1290, 1405, 1901, 5510}
2015/07/24
Engine News
Charging System Troubleshooting Guide Has Been Updated for All Engines {1406, 7569}
Charging System Troubleshooting Guide Has Been Updated for All Engines {1406, 7569}
Special Instruction
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Assembly Of Fan Drive Pulley Assemblies{1359}
Assembly Of Fan Drive Pulley Assemblies{1359}
Charging System Troubleshooting {1406}
Charging System Troubleshooting {1406}
Procedure for Replacing Regulator Kit on All Engines {1405}
Procedure for Replacing Regulator Kit on All Engines {1405}
Procedure to Install Brush Holder Assembly to End Frame on All Engines {1405}
Procedure to Install Brush Holder Assembly to End Frame on All Engines {1405}
Specifications
Alternators And Regulators
3208 DIESEL TRUCK ENGINE
Alternator
DELCO REMY 20-SI SERIES ALTERNATOR
Alternator
26SI Series Alternator
Alternator
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator
N3 Series Brushless Alternators
Systems Operation
Systems Operation
DELCO REMY 20-SI SERIES ALTERNATOR
General Information
26SI Series Alternator
Component Description
26SI Series Alternator
Normal Operation
26SI Series Alternator
General Information
HDB Series and M1 Series Heavy Duty Brushless Alternators
Normal Operation
HDB Series and M1 Series Heavy Duty Brushless Alternators
Component Description
HDB Series and M1 Series Heavy Duty Brushless Alternators
General Information
N3 Series Brushless Alternators
Component Description
N3 Series Brushless Alternators
Normal Operation
N3 Series Brushless Alternators
Testing and Adjusting
Testing And Adjusting
DELCO REMY 20-SI SERIES ALTERNATOR
T1 Alternator Output - Test
26SI Series Alternator
T2 Electrical System Current - Test
26SI Series Alternator
T3 Charging System - Test
26SI Series Alternator
T4 Alternator Drive System - Check
26SI Series Alternator
T5 Alternator Current - Test
26SI Series Alternator
T6 Residual Magnetism Restoration
26SI Series Alternator
T7 Identifying Source of Current Draw - Test
26SI Series Alternator
T8 Alternator Overcharging - Test
26SI Series Alternator
Initial Troubleshooting Procedure
26SI Series Alternator
General Information
26SI Series Alternator
Component - Test
26SI Series Alternator
Field Winding - Test
HDB Series and M1 Series Heavy Duty Brushless Alternators
Capacitor - Test
HDB Series and M1 Series Heavy Duty Brushless Alternators
Stator - Test
HDB Series and M1 Series Heavy Duty Brushless Alternators
Rectifier - Test
HDB Series and M1 Series Heavy Duty Brushless Alternators
Residual Magnetism - Restore
N3 Series Brushless Alternators
Regulator - Test
HDB Series and M1 Series Heavy Duty Brushless Alternators
Field Winding - Test
N3 Series Brushless Alternators
Capacitor - Test
N3 Series Brushless Alternators
Rectifier - Test
N3 Series Brushless Alternators
Stator - Test
N3 Series Brushless Alternators
Regulator - Test
N3 Series Brushless Alternators
Troubleshooting
General Information
N3 Series Brushless Alternators
Charging System
HDB Series and M1 Series Heavy Duty Brushless Alternators
Disassembly and Assembly
Alternator
DELCO REMY 20-SI SERIES ALTERNATOR
Alternator - Assemble
26SI Series Alternator
Alternator - Disassemble
26SI Series Alternator
Alternator - Disassemble - M1 Series Alternator (35 Amp)
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Assemble - M1 Series Alternator (35 Amp)
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Assemble - HDB Series Alternator
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Disassemble - HDB Series Alternator
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Assemble
N3 Series Brushless Alternators
Alternator - Disassemble
N3 Series Brushless Alternators
Service Magazine
New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23
Engine Ground Straps Necessary To Prevent Electrical Discharge Damage To Crankshaft Bearings{1202,1203,1400,1405}
1982/06/21
Keep Alternators Without Pulleys In A Horizontal Position During Installation To Prevent Internal Damage{1405}
1983/08/15
Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01
Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04
Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04
Check Alternator Output Connection Prior To Machine Delivery{1405}
1987/05/18
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
New Alternator Used In Charging Alternator Groups{1405}
1987/09/21
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
8T5314 Socket Adapter Available To Correctly Install Alternator Pulley Nut {0601}
1988/01/25
New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
Repair Parts Available for Alternator R-Terminal {1405}
2000/10/02
Harness Repair of Alternator R-Terminal Connector {1405, 1408, 7553}
2000/10/02
Charging System Troubleshooting Guide Has Been Updated for All Machines {1406, 7569}
Charging System Troubleshooting Guide Has Been Updated for All Machines {1406, 7569}
Truck Engine News
Cold Weather Operation Reminder {1000, 1250, 1350, 1355, 1450, 1453, 1456}
2005/08/01
Engine News
Safety Vent Caps For Caterpillar Batteries
1977/07/13
Operation and Maintenance Manual
Cold Weather Recommendation Charts
Cold Weather Recommendations for On-Highway Diesel Truck Engines
Special Instruction
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Use Of 6V3025 Battery Cable Repair Kit{0613, 1400}
Use Of 6V3025 Battery Cable Repair Kit{0613, 1400}
Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}
Technical Information Bulletin
Recommendations for Battery Charging and Temperatures for Machines and Generator Sets{1401, 751B}
Recommendations for Battery Charging and Temperatures for Machines and Generator Sets{1401, 751B}
Process for Communicating an Incident with a Battery{1401}
Process for Communicating an Incident with a Battery{1401}
Tool Operating Manual
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
Service Magazine
Maintenance Free Batteries{1401}
1986/03/10
Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07
Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01
Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11
5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23
Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04
Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04
Testing The Starter On The Engine{1401,1450}
1987/05/04
Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14
Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20
Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12
Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29
New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05
Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26
High Performance Maintenance Free Battery Available{1401}
1989/01/16
Limitations On Engine Cranking Time{1453,1401}
1989/03/27
Preventive Maintenance For Batteries{1401}
1989/03/27
Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24
Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Special Instruction, &quot;Battery Charging Rate And Time Tables,&quot; Available On Oil Resistant Paper{0374,1401}
1989/06/19
Engine News
Rack Shut-Off Solenoid Can Be Removed And Engine Started When There Is An Emergency
1980/11/12
Service Magazine
New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10
Truck Engine News
Engine Control Module (ECM) Hotline Is Now Available {1901}
2000/03/01
Cold Weather Operation Reminder {1000, 1250, 1350, 1355, 1450, 1453, 1456}
2005/08/01
Setting Modifications for the Messenger Display that Is Used With On-Highway Truck Engines in South America and Venezuela {1901, 1920, 7490}
2008/12/01
Cat<SUP>&reg;</SUP> Reman Announces the Availability of Additional Engine Components for Certain Truck Engine Applications {1052, 108F, 1210, 1265, 1290, 1405, 1901, 5510}
2015/07/24
Engine News
A New Electronic Control Module Wash Out Process {1901, 1920}
A New Electronic Control Module Wash Out Process {1901, 1920}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
Operation and Maintenance Manual
Cold Weather Recommendation Charts
Cold Weather Recommendations for On-Highway Diesel Truck Engines
Special Instruction
&quot;A Series&quot; Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation of Fuel Injection Pump and Governor Service Group{1286}
Installation of Fuel Injection Pump and Governor Service Group{1286}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Instructions for Communicating With and Flashing the <NOBR>10R-4085</NOBR> Engine Electronic Control Gp and the <NOBR>10R-1824</NOBR> Engine Electronic Control Gp {1901, 1920}
Instructions for Communicating With and Flashing the 10R-4085 Engine Electronic Control Gp and the 10R-1824 Engine Electronic Control Gp {1901, 1920}
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Procedure to Flash the ADEM 3 Engine Electronic Control Gp {1901, 1920}
Procedure to Flash the ADEM 3 Engine Electronic Control Gp {1901, 1920}
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Service Magazine
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
New Machine Software for Cat<SUP>&reg;</SUP> Product Link Is Now Available on Certain Cat<SUP>&reg;</SUP> Products {7490, 7606, 7610, 7620}
New Machine Software for Cat® Product Link Is Now Available on Certain Cat® Products {7490, 7606, 7610, 7620}
Special Instruction
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Service Magazine
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
Special Instruction
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Service Magazine
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
Engine News
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
Special Instruction
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Service Magazine
New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
New Machine Software for Cat<SUP>&reg;</SUP> Product Link Is Now Available on Certain Cat<SUP>&reg;</SUP> Products {7490, 7606, 7610, 7620}
New Machine Software for Cat® Product Link Is Now Available on Certain Cat® Products {7490, 7606, 7610, 7620}
Special Instruction
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Service Magazine
New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23
Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01
Special Instruction
Installation of 3208T Remanufactured Engine for Industrial, Truck and Electrical Power Generation (EPG) Engines{1200}
Installation of 3208T Remanufactured Engine for Industrial, Truck and Electrical Power Generation (EPG) Engines{1200}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Operation And Maintenance Of 1P3060 Pyrometer Group{0776}
Operation And Maintenance Of 1P3060 Pyrometer Group{0776}
Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}
Service Magazine
Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28
Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29
Tachometer Drive Is Now An Attachment{1166,1250,7450,7452,7487}
1985/08/12
Maintenance Free Batteries{1401}
1986/03/10
New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10
Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07
Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01
Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10
Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15
Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11
12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16
Polarity Connections And Use Of Service Meter Films When Service Meter Kits Are Installed{7480,7000}
1987/02/16
Check For Plugged Orifices In Mechanical Pressure Gauges{7450}
1987/03/02
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04
Testing The Starter On The Engine{1401,1450}
1987/05/04
Improved Start Switch Used{1416}
1987/05/25
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14
Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14
9G7641 Start Switch Is Improved{1416,1400}
1988/05/16
Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20
Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12
Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05
More Potting Material Now Used In 6N5906 Electric Service Meter{7480}
1979/11/26
Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26
High Performance Maintenance Free Battery Available{1401}
1989/01/16
Limitations On Engine Cranking Time{1453,1401}
1989/03/27
How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27
Preventive Maintenance For Batteries{1401}
1989/03/27
Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24
Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Special Instruction, &quot;Battery Charging Rate And Time Tables,&quot; Available On Oil Resistant Paper{0374,1401}
1989/06/19
Improved Starter Solenoid Assemblies Available {1467,1518}
1996/09/02
Special Instruction
Cat<SUP>&reg;</SUP> VIMS Converter Functionality {7610, 7620}
Cat® VIMS Converter Functionality {7610, 7620}
Service Magazine
"Maintenance Mode" in Product Link is Used to Prevent Codes From Being Transmitted When Performing Service to a Machine or Engine {7606}
2014/11/24
New Software Is Now Available for Cat<SUP>&reg;</SUP> Product Link {7606, 7610, 7620}
New Software Is Now Available for Cat® Product Link {7606, 7610, 7620}
New Machine Software for Cat<SUP>&reg;</SUP> Product Link Is Now Available on Certain Cat<SUP>&reg;</SUP> Products {7490, 7606, 7610, 7620}
New Machine Software for Cat® Product Link Is Now Available on Certain Cat® Products {7490, 7606, 7610, 7620}
Event Identification Number (EID) Above 60000 is Now Used on All Cat<SUP>&reg;</SUP> Products {1400}
Event Identification Number (EID) Above 60000 is Now Used on All Cat® Products {1400}
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Special Instruction
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Magazine
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
New Engine Timing Indicator Group Available {0781,0782}
1986/07/07
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Four New Contact Points Added To 5P6524 Engine Timing Indicator Group{0653}
1978/08/07
Special Instruction
Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}
Service Magazine
Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28
Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Testing The Starter On The Engine{1401,1450}
1987/05/04
Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14
Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24
Truck Engine News
New Address For Repair Of Diagnostic Tools
1982/06/23
Engine Ground Straps Necessary To Prevent Electrical Discharge Damage To Crankshaft Bearings
1982/06/23
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/09/01
Brushless Alternators May Not Charge In Certain Conditions
1986/07/01
Heavy-Duty Line Of Batteries Available To U.S. Dealers
1986/09/01
Adjust Bosch Solenoid If Replaced Or Reinstalled
1987/12/01
New Spring Used In Governor Control Groups
1992/04/01
Engine News
Rack Shut-Off Solenoid Can Be Removed And Engine Started When There Is An Emergency
1980/11/12
Safety Vent Caps For Caterpillar Batteries
1977/07/13
Special Instruction
Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}
Specifications
Alternator
DELCO REMY 20-SI SERIES ALTERNATOR
Systems Operation
Systems Operation
DELCO REMY 20-SI SERIES ALTERNATOR
Testing and Adjusting
Testing And Adjusting
DELCO REMY 20-SI SERIES ALTERNATOR
Disassembly and Assembly
Alternator
DELCO REMY 20-SI SERIES ALTERNATOR
Service Magazine
Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08
New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23
Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01
Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28
New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22
New Shutoff Solenoid Group Used{1259}
1983/03/21
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Maintenance Free Batteries{1401}
1986/03/10
New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10
Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07
Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01
Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10
Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15
Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23
Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23
Use Improved Heat Start Switch{1416}
1987/04/20
Products Equipped With Diagnostic Connectors Require Less Time For Electrical Troubleshooting{1400}
1987/05/04
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04
Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04
Testing The Starter On The Engine{1401,1450}
1987/05/04
Check Alternator Output Connection Prior To Machine Delivery{1405}
1987/05/18
Improved Start Switch Used{1416}
1987/05/25
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
9G7641 Start Switch Is Improved{1416,1400}
1988/05/16
Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20
Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12
New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13
Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24
Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05
Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
High Performance Maintenance Free Battery Available{1401}
1989/01/16
Limitations On Engine Cranking Time{1453,1401}
1989/03/27
How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27
Preventive Maintenance For Batteries{1401}
1989/03/27
Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24
Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01
Special Instruction, &quot;Battery Charging Rate And Time Tables,&quot; Available On Oil Resistant Paper{0374,1401}
1989/06/19
New Spring Used In Governor Control Groups{1265}
1992/04/20
Special Instruction
Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}
Service Magazine
Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28
Special Instruction
Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Service Magazine
New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23
Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
Special Instruction
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
Tool Operating Manual
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Service Magazine
New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10
Truck Engine News
Troubleshooting Water In Shut-off Solenoid Housing
1981/07/07
Bent Lever For Fuel Shut-off Solenoid Can Cause Low Engine Performance
1982/02/17
New Shutoff Solenoid Group Used
1983/04/13
Remove Diode Assemblies From Shutoff Solenoids
1984/11/07
New Spring Used In Governor Control Groups
1992/04/01
Engine News
Rack Shut-Off Solenoid Can Be Removed And Engine Started When There Is An Emergency
1980/11/12
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Special Instruction
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Specifications
Shutoff Solenoids
3208 DIESEL TRUCK ENGINE
Disassembly and Assembly
Shutoff Housing
3208 DIESEL TRUCK ENGINE
Service Magazine
Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08
Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01
New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22
New Shutoff Solenoid Group Used{1259}
1983/03/21
Remove Diode Assemblies From Shutoff Solenoids{1259}
1984/11/05
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
New Spring Used In Governor Control Groups{1265}
1992/04/20
Improved Starter Solenoid Assemblies Available {1467,1518}
1996/09/02
Truck Engine News
Troubleshooting Water In Shut-off Solenoid Housing
1981/07/07
Bent Lever For Fuel Shut-off Solenoid Can Cause Low Engine Performance
1982/02/17
New Shutoff Solenoid Group Used
1983/04/13
Remove Diode Assemblies From Shutoff Solenoids
1984/11/07
Adjust Bosch Solenoid If Replaced Or Reinstalled
1987/12/01
Engine News
Rack Shut-Off Solenoid Can Be Removed And Engine Started When There Is An Emergency
1980/11/12
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Specifications
Starter Motor Solenoids
3208 DIESEL TRUCK ENGINE
Shutoff Solenoids
3208 DIESEL TRUCK ENGINE
Service Magazine
Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08
Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01
New Shutoff Solenoid Group Used{1259}
1983/03/21
Remove Diode Assemblies From Shutoff Solenoids{1259}
1984/11/05
Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16
Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14
Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24
Improved Starter Solenoid Assemblies Available {1467,1518}
1996/09/02
Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08
New Shutoff Solenoid Group Used{1259}
1983/03/21
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
Truck Engine News
Cold Weather Operation Reminder {1000, 1250, 1350, 1355, 1450, 1453, 1456}
2005/08/01
Operation and Maintenance Manual
Cold Weather Recommendation Charts
Cold Weather Recommendations for On-Highway Diesel Truck Engines
Service Magazine
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Special Instruction
Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}
Service Magazine
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Testing The Starter On The Engine{1401,1450}
1987/05/04
Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14
Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24
General Service Information
Introduction
DELCO REMY CRANKING MOTORS 30-MT, 35-MT, 40-MT, 50-MT SERIES
Delco Remy
DELCO REMY CRANKING MOTORS 30-MT, 35-MT, 40-MT, 50-MT SERIES
Truck Engine News
Adjust Bosch Solenoid If Replaced Or Reinstalled
1987/12/01
New Starting Motors Used {1453}
2002/05/01
Cold Weather Operation Reminder {1000, 1250, 1350, 1355, 1450, 1453, 1456}
2005/08/01
Engine News
A Special Instruction Is Available For Replacing Starting Motor Solenoids {1467}
2001/08/01
Operation and Maintenance Manual
Starting Recommendations
Cold Weather Recommendations for On-Highway Diesel Truck Engines
Cold Weather Recommendation Charts
Cold Weather Recommendations for On-Highway Diesel Truck Engines
Special Instruction
Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}
Caterpillar PRELUB<SUP>&reg;</SUP> Diagnostics{1469}
Caterpillar PRELUB® Diagnostics{1469}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Replace Armature of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Specifications
Starter Motors
3208 DIESEL TRUCK ENGINE
Starter Motor Solenoids
3208 DIESEL TRUCK ENGINE
Starting Motor
37-MT, 41-MT, and 42-MT Series Starting Motors
Systems Operation
General Information
37-MT, 41-MT, and 42-MT Series Starting Motors
Component Description
37-MT, 41-MT, and 42-MT Series Starting Motors
Normal Operation
37-MT, 41-MT, and 42-MT Series Starting Motors
Testing and Adjusting
No Load - Test
37-MT, 41-MT, and 42-MT Series Starting Motors
Brush and Brush Holder - Check
37-MT, 41-MT, and 42-MT Series Starting Motors
Pinion Clearance - Adjust
37-MT, 41-MT, and 42-MT Series Starting Motors
Starting Motor Solenoid - Test
37-MT, 41-MT, and 42-MT Series Starting Motors
Troubleshooting
Engine Does Not Crank with Starting Motor On and Pinion Engaging Ring Gear
37-MT, 41-MT, and 42-MT Series Starting Motors
Starting Motor Does Not Turn or Turns Slowly
37-MT, 41-MT, and 42-MT Series Starting Motors
General Information
37-MT, 41-MT, and 42-MT Series Starting Motors
Disassembly and Assembly
Starter
3208 DIESEL TRUCK ENGINE
Starting Motor - Disassemble - 37-MT and 41-MT
37-MT, 41-MT, and 42-MT Series Starting Motors
General Information
37-MT, 41-MT, and 42-MT Series Starting Motors
Starting Motor - Assemble - 37-MT and 41-MT
37-MT, 41-MT, and 42-MT Series Starting Motors
Starting Motor - Disassemble - 42-MT
37-MT, 41-MT, and 42-MT Series Starting Motors
Starting Motor - Assemble - 42-MT
37-MT, 41-MT, and 42-MT Series Starting Motors
Service Magazine
Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28
Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10
12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Testing The Starter On The Engine{1401,1450}
1987/05/04
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14
Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14
Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05
Limitations On Engine Cranking Time{1453,1401}
1989/03/27
Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24
New Flywheel Ring Gear Available To Improve Starter Engagement{1158,1454}
1990/04/02
0R5207 Remanufactured Starter May Not Fit In Some Applications{1453}
1993/11/29
Improved Starter Solenoid Assemblies Available {1467,1518}
1996/09/02
Special Instruction
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}
Service Magazine
Maintenance Free Batteries{1401}
1986/03/10
New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10
Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07
Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01
Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15
Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11
5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23
Use Improved Heat Start Switch{1416}
1987/04/20
Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04
Testing The Starter On The Engine{1401,1450}
1987/05/04
Improved Start Switch Used{1416}
1987/05/25
Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14
9G7641 Start Switch Is Improved{1416,1400}
1988/05/16
Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20
Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05
Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26
High Performance Maintenance Free Battery Available{1401}
1989/01/16
Limitations On Engine Cranking Time{1453,1401}
1989/03/27
Preventive Maintenance For Batteries{1401}
1989/03/27
Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24
Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Special Instruction, &quot;Battery Charging Rate And Time Tables,&quot; Available On Oil Resistant Paper{0374,1401}
1989/06/19
Truck Engine News
New Address For Repair Of Diagnostic Tools
1982/06/23
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/09/01
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Tool Operating Manual
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
Reuse And Salvage Guidelines
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Troubleshooting
Service Tools
N3 Series Brushless Alternators
Service Tools
37-MT, 41-MT, and 42-MT Series Starting Motors
Service Magazine
New Address For Repair Of Diagnostic Tools{0650}
1982/06/14
6V6124 Calibration Coil Available To Calibrate And Check 6V4910 AC/DC Clamp-On Ammeter{0651}
1982/06/28
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23
Two New Self-Powered Digital Tachometers And Signal Generator Available {7462}
1987/05/11
Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12
Diagnostic Cables and Harnesses Are Available {0785}
2000/12/25
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
Compression Ratio Increased On Remanufactured OR1094 &amp; OR1095 Engines To Reduce Amount Of White Smoke On Cold Weather Start-Ups{1000,1254,1290}
1991/09/30
Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23
Engine News
Correction to The Pocket Guide, SEBD0402 Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/07/01
Special Instruction
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}
Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}
Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}
Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}
Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}
Repair Procedure for Damaged Harness Wiring {1408}
Repair Procedure for Damaged Harness Wiring {1408}
Tool Operating Manual
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Reuse And Salvage Guidelines
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Service Magazine
Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29
Maintenance Free Batteries{1401}
1986/03/10
New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10
Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01
Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11
5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04
Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04
Testing The Starter On The Engine{1401,1450}
1987/05/04
Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14
Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20
Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12
Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05
Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26
High Performance Maintenance Free Battery Available{1401}
1989/01/16
Limitations On Engine Cranking Time{1453,1401}
1989/03/27
How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27
Preventive Maintenance For Batteries{1401}
1989/03/27
Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24
Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01
Special Instruction, &quot;Battery Charging Rate And Time Tables,&quot; Available On Oil Resistant Paper{0374,1401}
1989/06/19
Compression Ratio Increased On Remanufactured OR1094 &amp; OR1095 Engines To Reduce Amount Of White Smoke On Cold Weather Start-Ups{1000,1254,1290}
1991/09/30
Correction to The Pocket Guide, SEBD0402, Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/06/26
Harness Repair of Alternator R-Terminal Connector {1405, 1408, 7553}
2000/10/02
Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2000/10/09
Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}
Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}
Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14
Truck Engine News
Setting Modifications for the Messenger Display that Is Used With On-Highway Truck Engines in South America and Venezuela {1901, 1920, 7490}
2008/12/01
Engine News
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
Special Instruction
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Cat<SUP>&reg;</SUP> VIMS Converter Functionality {7610, 7620}
Cat® VIMS Converter Functionality {7610, 7620}
Service Magazine
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
New Inspection and Repair Procedure Is Now Available for Cat<SUP>&reg;</SUP> Products Located in India Equipped with Product Link {7606}
2014/09/22
New Software Is Now Available for All Cat<SUP>&reg;</SUP> Products With PL522 China System {7606, 7620}
2015/03/04
New Troubleshooting Procedure Is Now Available for all Cat<SUP>&reg;</SUP> Products Equipped with PL321 VIMS (PL321 VSR) {7606}
2015/05/12
New Software Is Now Available for Cat<SUP>&reg;</SUP> Product Link {7606, 7610, 7620}
New Software Is Now Available for Cat® Product Link {7606, 7610, 7620}
Truck Engine News
Two New Cold Weather Fuel Heaters Available
1986/11/01
Incorrect Use Of Fuel Heaters Can Reduce Engine Power
1987/02/01
Cold Weather Operation Reminder {1000, 1250, 1350, 1355, 1450, 1453, 1456}
2005/08/01
Engine News
Fuel Heaters Are Now Available For Field Installation
1980/01/09
Special Instruction
Installation Of 9N3829 Jacket Water Heater Group{1383}
Installation Of 9N3829 Jacket Water Heater Group{1383}
Installation of 7E-6310, 9X-3294, 6N-9125, 7E-5244 and 3T-8724 Jacket Water Heater Groups{1383}
Installation of 7E-6310, 9X-3294, 6N-9125, 7E-5244 and 3T-8724 Jacket Water Heater Groups{1383}
Installation Instructions for Jacket Water Heaters with Seal Kits{1383}
Installation Instructions for Jacket Water Heaters with Seal Kits{1383}
Service Magazine
Fuel Heaters Are Now Available For Field Installation {1296}
1980/01/07
Two New Cold Weather Fuel Heaters Available {1296}
1986/11/03
Incorrect Use Of Fuel Heaters Can Reduce Engine Power{1296}
1987/02/16
How To Identify Failures To Electric Jacket Water Heaters{1383}
1988/04/18
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Special Instruction
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Service Magazine
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
Engine News
A New Electronic Control Module Wash Out Process {1901, 1920}
A New Electronic Control Module Wash Out Process {1901, 1920}
Special Instruction
Installation Instructions For Product Link 101 Inline Timer{7602}
Installation Instructions For Product Link 101 Inline Timer{7602}
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Service Magazine
New Flash File Software Is Used for Product Link 151/201 {7606, 7620}
2002/07/15
Improved VisionLink And VisionLink Store Software Are Now Available for All Caterpillar Products {7606, 7620}
2015/09/15
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
New Software Is Now Available for All Cat<SUP>&reg;</SUP> Products With The Product Link PL421 or Product Link PL420 System {7606, 7620}
2014/12/10
New Software for Product Link PL522 Module Is Now Available for All Cat<SUP>&reg;</SUP> Products {7606}
2014/08/08
Loss of Daily Reports May Be an Indicator of End of Life for the Product Link<SUP>&reg;</SUP> ECM on PL321SR and PL321VSR Systems {7606}
2014/06/24
Capturing Engine Stop Messages and Idle Information on All Caterpillar Products Equipped with Product Link 522 {7606}
2014/07/25
Service Meter Adjustment Is Now Available in VisionLink<SUP>TM</SUP> {7478, 7606}
2014/08/20
New Inspection and Repair Procedure Is Now Available for Cat<SUP>&reg;</SUP> Products Located in India Equipped with Product Link {7606}
2014/09/22
"Maintenance Mode" in Product Link is Used to Prevent Codes From Being Transmitted When Performing Service to a Machine or Engine {7606}
2014/11/24
Revision to "Reports and Messages Not Available" Troubleshooting Procedure for Cat<SUP>&reg;</SUP> Products with Cat<SUP>&reg;</SUP> Product Link 121/321 {7606}
2014/12/24
Event Codes (E2131, E2132, or E2133) Appearing Occasionally with On-board Machine Systems with a PL321, or PL121 Satellite System Installed {7600, 7606}
2015/01/06
Procedure to Improve Reporting into VisionLink after Re-Registration of Product Link Systems PL121/321 {7606}
2015/03/17
New Software Is Now Available for All Cat<SUP>&reg;</SUP> Products With PL522 China System {7606, 7620}
2015/03/04
New Software for Product Link PL522 Module Is Now Available for All Cat<SUP>&reg;</SUP> Products {7606, 7620}
2015/06/26
New Troubleshooting Procedure Is Now Available for all Cat<SUP>&reg;</SUP> Products Equipped with PL321 VIMS (PL321 VSR) {7606}
2015/05/12
New Product Link Software for PL300 Is Now Available for All Cat<SUP>&reg;</SUP> Products {7606, 7620}
2015/09/11
Special Instruction
Diagnostic Code Information for Caterpillar <SUP>&reg;</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Service Magazine
Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16
Service Meter Adjustment Is Now Available in VisionLink<SUP>TM</SUP> {7478, 7606}
2014/08/20
Special Instruction
Procedure to Replace Armature of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Tool Operating Manual
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Reuse And Salvage Guidelines
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Service Magazine
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Truck sale:

 
11,500 
Caterpillar D3208EP, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY
CATERPILLAR 3208 1993
 
CATERPILLAR 3208 1993
- STATIONARY - DIESEL
WAGNER EQUIPMENT CO
United States
CATERPILLAR 3208 2004
 
CATERPILLAR 3208 2004
- STATIONARY GENERATOR SETS
EMPRESAS MATCO, S.A. DE C.V.
Sufragio Efectivo Norte 870 - Obregón -
1998 CAT 3208
USD $19,000 
1998 CAT 3208

Galactic Liquidation LLC
1990 CAT 3208
 
1990 CAT 3208

Ken Porter Auctions
Carson, California
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.