IMPLEMENTS
ELEVATOR GPOPERATOR STATION
AIR CONDITIONER GPCONTROL GP-HYDRAULIC
CONTROL GP-TRANSMISSION
DOOR GP
IMPLEMENTS
ELEVATOR GP
#SEBP17860380
2T-0048: ROLLER GP-ELEVATOR CHAIN
2T-0048 ROLLER GP-ELEVATOR CHAIN
S/N 2XG1-UP
PART OF 2T-0044 FRAME GP-ELEVATOR
S/N 2XG1-UP
PART OF 2T-0044 FRAME GP-ELEVATOR
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9W-7228 | [1] | SEAL GP-DUO-CONE | |
| 2. | 5P-9120 | [1] | RING-SEALING | |
| 3. | 8J-6560 | [2] | CAP | |
| 4. | 7H-3171 | [2] | PLUG-PIPE | |
| 5. | 8J-9823 | [2] | RING-RETAINING | |
| 6. | 8J-6556 | [2] | WASHER-THRUST (63.5X108X3.175-MM THK) | |
| 7. | 8J-6559 | [1] | SHAFT | |
| 8. | 8J-6557 | [2] | BEARING-IRON | |
| 9. | 7M-7410 | [1] | PLUG-PIPE | |
| 10. | 2T-0242 | [1] | IDLER |
#SEBP17860381
310-3510: ROLLER GP-ELEVATOR CHAIN
310-3510 ROLLER GP-ELEVATOR CHAIN
S/N 2XG1-UP
PART OF 2T-0044 FRAME GP-ELEVATOR
S/N 2XG1-UP
PART OF 2T-0044 FRAME GP-ELEVATOR
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3G-7489 | [1] | CAP | |
| 2. | 8J-6552 | [1] | CARRIER-BEARING | |
| 3. | 8J-9810 | [1] | GASKET | |
| 4. | 325-7477 | [1] | ROLLER-IDLER | |
| 5. | 310-5273 | [1] | WASHER (34X65X16-MM THK) | |
| 6. | 030-0058 | [1] | BEARING AS-ROLLER | |
| 7. | 3B-8489 | [1] | FITTING-GREASE (1/8-27 PTF) | |
| 8. | 4L-9337 | [4] | BOLT (3/8-16X1.5-IN) | |
| 9. | 5L-4776 | [1] | SEAL-LIP TYPE | |
| 10. | 6V-3483 | [1] | BOLT (1-1/4-7X13.5-IN) | |
| 11. | 8T-4896 | [4] | WASHER-HARD (10.2X18.5X2.5-MM THK) |
#SEBP17860382
2T-2792: AIR CONDITIONER & MOUNTING GP
2T-2792 AIR CONDITIONER & MOUNTING GP
S/N 5TF1-99999
HEATS & COOLS
PART OF 2T-2912 AIR CONDITIONER AR
AN ATTACHMENT
S/N 5TF1-99999
HEATS & COOLS
PART OF 2T-2912 AIR CONDITIONER AR
AN ATTACHMENT
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 2T-2995 I | [1] | HOSE AS | |
| 2. | 6M-5062 | [2] | SEAL-O-RING | |
| 3. | 2T-0663 | [1] | CONDENSER | |
| 4. | 2T-1039 | [4] | PLATE | |
| 5. | 8T-9364 | [4] | BOLT (1/4-20X0.625-IN) | |
| 6. | 5P-4115 | [4] | WASHER-HARD (7.2X19X2-MM THK) | |
| 7. | 3G-1551 I | [1] | HOSE AS | |
| 8. | 5F-9144 | [3] | SEAL-O-RING | |
| 9. | 5L-4758 | [1] | SEAL-O-RING | |
| 10. | 3G-1423 | [1] | CLAMP AS | |
| 11. | 9D-6888 | [1] | DRYER-REFRIGERANT (RECEIVER) | |
| 12. | 4L-6454 | [1] | BOLT (3/8-16X1-IN) | |
| 8T-4896 | [1] | WASHER-HARD (10.2X18.5X2.5-MM THK) | ||
| 13. | 3T-3048 | [1] | CLIP AS | |
| 6D-1641 | [1] | CLIP (LOOP) | ||
| 14. | 0L-0639 | [1] | BOLT (3/8-24X2.25-IN) | |
| 15. | 6V-0880 | [1] | FITTING AS | |
| 2L-1224 | CAP-SEAL (HIGH SIDE) | |||
| 16. | 6V-0879 | [1] | FITTING AS | |
| 8C-5248 | CAP | |||
| 17. | 3S-8665 | [4] | CLIP (LOOP) | |
| 18. | 9M-8406 | [1] | CLIP (LOOP) | |
| 19. | 1P-6356 | [1] | PLATE | |
| 20. | 5K-5338 | [1] | CLIP (LOOP) | |
| 21. | 7K-1181 | [4] | STRAP-CABLE | |
| 22. | 6D-1641 | [1] | CLIP (LOOP) | |
| 23. | 9W-4111 Y | [1] | AIR CONDITIONER GP | |
| 3G-6429 B | [24] | SEAL | ||
| 24. | 5S-7379 | [14] | BOLT (3/8-16X0.875-IN) | |
| 25. | 5P-1075 | [16] | WASHER-HARD (10.2X22.5X3-MM THK) | |
| 26. | 3G-6426 | [1] | ANGLE | |
| 27. | 3G-6427 | [1] | ANGLE | |
| 28. | 9G-2264 | [1] | CLIP-CONNECTOR | |
| 29. | 2T-1978 | [2] | SEAL | |
| 30. | 5M-6668 | [2] | SCREW-MACHINE (8-32X0.75-IN) | |
| 31. | 3T-8728 | [1] | CIRCUIT BREAKER AS (20-AMPERE) | |
| 6V-8376 | [2] | SCREW-MACHINE (8-32X0.25-IN) | ||
| 9B-7233 | [2] | LOCKWASHER | ||
| 32. | 5T-9895 | [1] | HARNESS AS-CONSOLE (CIRCUIT BKR) | |
| 33. | 030-9612 | [1] | SCREW-FORMING (10-24X0.5-IN) | |
| 3G-2455 | [1] | ANGLE | ||
| 34. | 3T-3045 | [1] | CLIP AS | |
| 35. | 4B-4274 | [2] | WASHER (5.5X13X1.2-MM THK) | |
| 36. | 6D-1641 | [4] | CLIP (LOOP) | |
| 8T-4896 | [4] | WASHER-HARD (10.2X18.5X2.5-MM THK) | ||
| B | USE AS REQUIRED | |||
| I | REFER TO HYDRAULIC INFORMATION SYSTEM | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP17860383
2T-2912: AIR CONDITIONER AR
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS#SEBP17860384
9W-4111: AIR CONDITIONER GP
9W-4111 AIR CONDITIONER GP
S/N 5TF1-99999
PART OF 2T-2792 AIR CONDITIONER & MOUNTING GP
AN ATTACHMENT
S/N 5TF1-99999
PART OF 2T-2792 AIR CONDITIONER & MOUNTING GP
AN ATTACHMENT
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9W-4112 Y | [1] | HEATER GP-CAB | |
| 2. | 5P-6458 | [1] | SEAL-O-RING | |
| 3. | 5P-2492 | [2] | COUPLING-AIR CONDITIONER | |
| 4. | 5L-4758 | [2] | SEAL-O-RING | |
| 5. | 9D-4507 | [1] | COUPLING | |
| 6. | 5F-9144 | [2] | SEAL-O-RING | |
| 7. | 2G-0401 | [1] | VALVE | |
| 8. | 6M-5062 | [1] | SEAL-O-RING | |
| 9. | 2G-0429 | [1] | COIL-EVAPORATOR | |
| 10. | 5P-5673 D | SEAL (.5M) | ||
| 11. | 5S-7349 | [1] | BOLT (1/4-20X0.5-IN) | |
| 12. | 5P-4115 | [1] | WASHER-HARD (7.2X19X2-MM THK) | |
| 13. | 3T-0745 | [1] | CLIP | |
| 14. | 5P-5646 D | HOSE (3.4M) | ||
| 15. | 5P-2493 | [1] | COUPLING | |
| 16. | 5P-5664 D | HOSE (1.9M) | ||
| 17. | 2V-0099 | [1] | KNOB-CONTROL | |
| 18. | 2P-4339 | [1] | NUT-JAM (7/16-28-THD) | |
| 19. | 3E-5465 | [1] | THERMOSTAT (CAB AIR) | |
| 20. | 5P-7070 D | INSULATION-STRIP (.3M) | ||
| 21. | 3T-3198 | [1] | GROMMET | |
| 22. | 3T-3197 | [1] | GROMMET | |
| 23. | 8P-6355 | [1] | CLIP | |
| 24. | 2G-0395 | [2] | TUBE | |
| 25. | 7T-9793 | [2] | VALVE-CHECK | |
| D | ORDER BY THE METER | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP17860385
7C-8433: COMPRESSOR GP-REFRIGERANT
7C-8433 COMPRESSOR GP-REFRIGERANT
S/N 5TF1-99999
PART OF 2T-2912 AIR CONDITIONER AR
AN ATTACHMENT
S/N 5TF1-99999
PART OF 2T-2912 AIR CONDITIONER AR
AN ATTACHMENT
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8T-2502 B | [2] | BOLT (3/8-16X1.125-IN) | |
| 2. | 8T-4896 B | [14] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| 3. | 7W-4975 | [1] | STRAP | |
| 4. | 8T-4835 | [1] | BOLT (1/2-13X2-IN) | |
| 8F-0492 | [1] | SPACER (0.531X1.125X0.625-IN THK) | ||
| 5. | 8T-4223 | [3] | WASHER-HARD (13.5X25.5X3-MM THK) | |
| 6. | 7C-8236 | [1] | V-BELT | |
| 7. | 8T-9389 | [1] | BOLT (1/2-13X2.75-IN) | |
| 8. | 6V-8188 | [2] | NUT (1/2-13-THD) | |
| 9. | 5S-7383 | [2] | BOLT (3/8-16X1.75-IN) | |
| 10. | 7W-4973 | [1] | BRACKET | |
| 11. | 6V-4432 | [1] | BOLT (1/2-13X4-IN) | |
| 12. | 7W-4974 | [2] | PLATE | |
| 13. | 4L-9337 | [6] | BOLT (3/8-16X1.5-IN) | |
| 14. | 7T-8600 Y | [1] | COMPRESSOR GP-REFRIGERANT | |
| 15. | 7C-8434 | [1] | BRACKET | |
| 16. | 9G-9150 B | [1] | CLIP | |
| 17. | 6V-8801 B | [7] | NUT (3/8-16-THD) | |
| 18. | 7W-4978 | [1] | NUT AS | |
| B | USE AS REQUIRED | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP17860386
7T-8600: COMPRESSOR GP-REFRIGERANT
7T-8600 COMPRESSOR GP-REFRIGERANT
S/N 5TF1-99999
PART OF 7C-8433 COMPRESSOR GP-REFRIGERANT
AN ATTACHMENT
S/N 5TF1-99999
PART OF 7C-8433 COMPRESSOR GP-REFRIGERANT
AN ATTACHMENT
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 2K-0564 | [1] | LOCKNUT (1/2-20-THD) | |
| 2. | 1H-3338 | [3] | LOCKWASHER (EXTERNAL TOOTH) | |
| 3. | 8T-4171 M | [3] | BOLT (M6X1X12-MM) | |
| 4. | 8T-8816 | [1] | COMPRESSOR AS | |
| 1H-8171 | [2] | SEAL-O-RING | ||
| 7T-4532 | [1] | PLUG AS | ||
| 5. | 8T-8820 | [1] | DRIVE AS-CLUTCH | |
| 6. | 8C-4405 | [1] | RING-RETAINING | |
| 7. | 1B-8702 | [1] | KEY-WOODRUFF | |
| 8. | 8C-4158 J | [1] | SEAL-BEARING | |
| 9. | 8T-8814 | [1] | COVER-DUST | |
| 10. | 8T-8813 | [1] | COIL AS | |
| 7N-9737 | [1] | HOUSING-RECEPTACLE (14-GA TO 18-GA) | ||
| 7N-7780 | [1] | PIN-CONNECTOR (14-GA TO 18-GA) | ||
| 7N-7779 | [1] | SOCKET-CONNECTOR (14-GA TO 18-GA) | ||
| 11. | 8C-4160 J | [1] | SEAL-COIL | |
| 12. | 8C-4159 J | [1] | SEAL-PULLEY | |
| 13. | 8T-8817 | [1] | BALL BEARING | |
| AVAILABLE REPAIR KIT(S): | ||||
| 8T-8815 | [1] | KIT-REFRIGERANT SEAL | ||
| 8T-8819 | [1] | KIT-REPAIR | ||
| (INCLUDES KEY, SHIMS, RINGS, CLAMP & NUT) | ||||
| 8T-8821 J | [1] | KIT-DUST SEAL | ||
| (INCLUDES FRONT BEARING SEALS, REAR PULLEY SEALS & COIL SEAL) | ||||
| J | KIT MARKED J INCLUDES PART(S) MARKED J | |||
| M | METRIC PART | |||
#SEBP17860387
2T-2406: CONTROL GP-HYDRAULIC HAND
2T-2406 CONTROL GP-HYDRAULIC HAND
S/N 5TF1-99999
POSITION
PART OF 2T-2803 ROPS AR
S/N 5TF1-99999
POSITION
PART OF 2T-2803 ROPS AR
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 0L-0829 | [3] | HANDLE | |
| 2. | 2T-2536 | [1] | LEVER AS (ELEVATOR SPEED) | |
| 3. | 2T-2533 | [1] | LEVER AS (FLOOR & EJECTOR) | |
| 4. | 2T-1168 | [1] | LEVER AS (BOWL) | |
| 5. | 8W-1304 C | [1] | KNOB | |
| 6. | 5P-0537 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 7. | 3B-4617 | [2] | PIN-COTTER | |
| 1B-0676 | [2] | PIN | ||
| 8. | 1B-4430 | [1] | NUT-JAM (1/2-20-THD) | |
| 5P-8245 | [1] | WASHER-HARD (13.5X25.5X3-MM THK) | ||
| 9. | 7H-3641 | [1] | END-ROD (5/16-24-THD) | |
| 10. | 9M-1974 | [8] | WASHER-HARD (8.8X16X2-MM THK) | |
| 11. | 1B-7182 | [3] | BOLT (5/16-18X1.25-IN) | |
| 12. | 035-2017 | [8] | SCREW-BUTTON HEAD (3/8-16X1-IN) | |
| 13. | 8T-4896 | [10] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| 14. | 9D-2851 | [1] | BOOT | |
| 15. | 5T-1645 C | [1] | LEVER AS (ELEVATOR) | |
| DIRECTION CONTROL) | ||||
| 16. | 8D-6044 | [1] | GASKET | |
| 17. | 1B-8735 | [1] | KEY-WOODRUFF | |
| 18. | 2K-0400 | [2] | END-YOKE ROD | |
| 19. | 4D-4064 | [2] | ROD END (3/8-24-THD) | |
| 20. | 2K-8467 | [1] | PIN-SPRING | |
| 21. | 8D-6022 | [1] | SUPPORT | |
| 22. | 4D-6432 | [1] | LOCKNUT (7/16-20-THD) | |
| 23. | 2G-4357 | [1] | STOP | |
| 24. | 9D-0738 | [2] | WASHER-THRUST (0.641X1.38X0.094-IN THK) | |
| 25. | 9D-8599 | [1] | BRACKET AS | |
| 9D-0744 | [1] | BRACKET | ||
| 1K-6649 | [1] | BUSHING-OILLESS | ||
| 26. | 3H-0992 | [2] | SPRING-RACK DECELERATOR | |
| 27. | 4F-8386 | [1] | GASKET | |
| 28. | 1L-4693 | [1] | ROD-CONTROL | |
| 29. | 3D-2682 | [2] | STUD | |
| 30. | 8D-8057 | [1] | PIN | |
| 31. | 4F-2294 | [3] | NUT-JAM (5/16-24-THD) | |
| 32. | 5B-9079 | [4] | NUT-JAM (3/8-24-THD) | |
| 33. | 6J-0488 | [2] | SCREW-BUTTON HEAD (3/8-16X0.875-IN) | |
| 34. | 3B-4612 | [2] | PIN-COTTER | |
| 2B-1560 | [2] | PIN | ||
| 35. | 2T-2722 | [1] | BRACKET | |
| 36. | 2T-2721 | [1] | CHANNEL | |
| 37. | 8D-8058 | [3] | BUSHING | |
| 38. | 5M-7937 | [1] | DOWEL | |
| C | CHANGE FROM PREVIOUS TYPE | |||
#SEBP17860388
2T-1743: CONTROL GP-TRANSMISSION
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 035-2017 | [4] | SCREW-BUTTON HEAD (3/8-16X1-IN) | |
| 2. | 5M-2894 | [10] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| 3. | 2A-1736 | [1] | HANDLE | |
| 4. | 5D-6379 | [1] | PLATE AS | |
| 5D-1753 | [1] | WASHER (9X25X4-MM THK) | ||
| 5. | 4D-0506 | [1] | HANDLE | |
| 6. | 5B-8407 | [1] | PIN | |
| 7. | 3D-5702 | [1] | BUSHING | |
| 8. | 4D-0587 | [1] | PIN | |
| 9. | 5F-7464 | [1] | SPRING | |
| 10. | 3B-4611 | [1] | PIN-COTTER | |
| 1A-8912 | [1] | WASHER (6.7X12.7X1.6-MM THK) | ||
| 11. | 2T-1744 | [1] | BLOCK AS | |
| 12. | 3V-4791 | [1] | GROMMET | |
| 13. | 4J-2701 | [1] | ROD END | |
| 14. | 2T-1746 | [1] | ROD-HANDLE | |
| 15. | 5M-9708 | [1] | SPRING | |
| 16. | 3B-4617 | [1] | PIN-COTTER | |
| 1B-0676 | [1] | PIN | ||
| 17. | 1D-5117 | [1] | NUT-JAM (1/2-13-THD) | |
| 18. | 2T-1745 | [1] | BRACKET AS | |
| 19. | 4B-9808 | [1] | SETSCREW (1/4-20X0.5-IN) | |
| 20. | 2T-1748 | [2] | SHAFT | |
| 21. | 010-2570 | [1] | SETSCREW (1/4-20X0.375-IN) | |
| 22. | 7F-9558 | [3] | BUSHING-TERMINAL | |
| 23. | 0S-0509 | [1] | BOLT (3/8-16X0.75-IN) | |
| 5P-9297 | [1] | CLIP (LOOP) | ||
| 25. | 0S-1615 | [1] | BOLT (1/4-20X0.75-IN) | |
| 7L-4186 | [1] | ROD END | ||
| 26. | 8T-8496 | [1] | CABLE AS (TRANSMISSION CONTROL) | |
| 27. | 2T-1719 | [1] | ANGLE AS | |
| 28. | 6J-0488 | [2] | SCREW-BUTTON HEAD (3/8-16X0.875-IN) | |
| 29. | 0L-1351 | [3] | BOLT (3/8-16X0.875-IN) | |
| 30. | 2T-1720 | [1] | BOX AS | |
| 31. | 2T-1281 | [1] | PLATE AS |
#SEBP17860389
2T-2296: DOOR GP-CAB
For full view, you need register
Parts for your 615C WHEEL SCRAPER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8T-3504 | [1] | HANDLE AS-INSIDE | |
| 2. | 8B-3768 | [2] | ROD END | |
| 3. | 9S-1303 | [2] | PIN | |
| 4. | 3B-4610 | [1] | PIN-COTTER | |
| 5. | 6V-8279 | [1] | LATCH-DOOR | |
| 6. | 3G-1992 | [1] | STRAP-DOOR | |
| 3G-1996 | [1] | ADJUSTER | ||
| 7. | 7X-0480 | [4] | SCREW-HEX SOCKET (3/8-16X2-IN) | |
| 2K-4973 | [4] | LOCKNUT (3/8-16-THD) | ||
| 5P-1075 | [4] | WASHER-HARD (10.2X22.5X3-MM THK) | ||
| 8. | 2T-1070 | [1] | WINDOW AS | |
| 9. | 5P-6605 D | SEAL (5.1M) | ||
| 10. | 2T-2297 | [1] | DOOR AS | |
| 11. | 3K-6584 | [1] | ROD-CONTROL | |
| 12. | 6F-0612 | [2] | NUT-JAM (1/4-28-THD) | |
| 13. | 8T-0438 J | [1] | HANDLE AS | |
| 14. | 6V-2687 | [4] | SCREW-PAN HEAD (10-24X1-IN) | |
| 4B-4274 | [4] | WASHER (5.5X13X1.2-MM THK) | ||
| 15. | 2T-1724 | [2] | ANGLE | |
| 16. | 6V-1193 | [4] | SCREW-HEX SOCKET (3/8-16X0.625-IN) | |
| 6N-8863 | [4] | WASHER (10.2X32X2.5-MM THK) | ||
| 17. | 6V-3260 | [4] | BOLT-SOCKET HEAD (1/4-20X0.75-IN) | |
| 18. | 6V-8185 | [2] | NUT (1/4-20-THD) | |
| 8T-4205 | [2] | WASHER-HARD (7.2X14.5X2-MM THK) | ||
| 4M-5281 | [2] | BOLT (1/4-20X0.75-IN) | ||
| 19. | 2T-2298 | [1] | ANGLE AS | |
| 20. | 2T-3901 | [1] | ASHTRAY | |
| 3G-4898 | [2] | SCREW | ||
| 3G-2470 | [2] | WASHER | ||
| 21. | 5P-0372 | [1] | LOCK PIN | |
| 22. | 2T-2299 | [1] | WINDOW | |
| 23. | 2T-2572 | [2] | HINGE | |
| 24. | 2T-2591 | [2] | PLATE | |
| 25. | 8T-4896 | [4] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| D | ORDER BY THE METER | |||
| J | REQUIRES 5P8500 KEY | |||
