3116 Industrial Engine 4PG00001-UP SERVICE EQUIPMENT AND SUPPLIES Caterpillar SIS

Engine News

New Caterpillar Publication, "Questions And Answers About Engine Bearings" Is Available
1980/08/13

Reuse Of Engine Bearings
1983/05/25

Reuse Of Engine Bearings
1983/11/30

New Main Bearing Material {1203}
1999/06/01

Special Instruction

Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}

Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}

Service Magazine

Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03

New Bearing Standard: Quantity Of One Part Number Now Has Both Halves Of The Bearing{7551}
1982/08/09

Reuse Of Engine Bearings{1230}
1983/05/16

Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21

Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08

Use Only Paint To Mark Connecting Rod Caps For Torque-Turn Method {1218,1219}
1987/06/01

Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12

Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28

New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04

Engine News

Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning
1979/08/22

Special Instructions Packaged With Turbocharger Cartridge Repair Kits May Be Incorrect
1986/02/01

Stop Engine If There Is A Turbocharger Bearing Failure
1987/04/01

New Turbocharger Models Have Left-Hand Threads On Compressor Nut And Turbine Shaft{1053,1052}
1994/03/01

Changes To Retainer Nut Torque And Assembly Procedures For Turbocharger Compressor Wheels
1977/03/15

Service Magazine

Use Care When Handling Turbocharger Compressor Wheels{1052,1077}
1985/12/16

Special Instructions Packaged With Turbocharger Cartridge Repair Kits May Be Incorrect{1053}
1986/02/03

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

Changes To Retainer Nut Torque And Assembly Procedures For Turbocharger Compressor Wheels{0374,1052}
1977/02/28

Stop Engine If There Is A Turbocharger Bearing Failure{1052,1318}
1987/04/06

Silicone Grease Now Used In Seal Ring Groove In Turbochargers{1052,1053,1077}
1978/05/15

Use Of 9S3265 Retaining Compound On Schwitzer Turbocharger Compressor Wheel Retainer Nuts{1052,1053}
1979/06/25

Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20

Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/09/03

6V2055 High Vacuum Grease Gives Better Oil Seal {1052,1053,1077,0682}
1979/09/10

Different Thrust Bearing And Thrust Rings Now Used In Turbochargers{1052,1053}
1979/10/22

New Turbocharger Models Have Left-Hand Threads On Compressor Nut And Turbine Shaft {1053,1052}
1994/02/28

Engine News

New Fuel Nozzle Test Sheet Available
1982/10/20

Reference Chart for Engine Improvements
1982/11/10

Polarity Connections And Use Of Service Meter Films When Service Meter Kits Are Installed
1987/05/01

New Engine Wall Charts Give Maintenance Management Recommendations
1989/03/01

4P6493 Governor Information Plate Available
1992/06/01

Piston Usage Chart For Two Piece Pistons{1214}
1995/08/01

New Engine Information Plates Require More Information{1000}
1996/02/16

Operation and Maintenance Manual

Engine Identification
3114, 3116, and 3126 Industrial and Generator Set Engines

Information Plate
3114, 3116, and 3126 Industrial and Generator Set Engines

Reference Numbers
3114, 3116, and 3126 Industrial and Generator Set Engines

Serial Number Plate
3114, 3116, and 3126 Industrial and Generator Set Engines

Safety Signs and Labels
3114, 3116, and 3126 Industrial and Generator Set Engines

Emissions Certification Film
3114, 3116, and 3126 Industrial and Generator Set Engines

Special Instruction

Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Service Magazine

Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur{1318,0375,0374,1280}
1982/05/03

Separate Valve Stem Gauges Available{0653,1000}
1982/06/07

New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04

Reference Chart for Engine Improvements{0374,1000}
1982/10/25

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Engine Information Plate Contains More Data; Use Of Performance Specifications{1250,7557}
1985/10/28

Polarity Connections And Use Of Service Meter Films When Service Meter Kits Are Installed{7480,7000}
1987/02/16

Use Only Paint To Mark Connecting Rod Caps For Torque-Turn Method {1218,1219}
1987/06/01

Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22

Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27

New Engine Wall Charts Give Maintenance Management Recommendations{0374,0375,7500,7557,7580}
1989/03/06

4P6493 Governor Information Plate Available{7557}
1992/06/15

Lubricant Will Ease Installation Of Secondary Radial Seal Air Filter Element {1054}
1994/04/25

Service Charts and Decals Available {0374, 0375, 7405, 7557}
2000/03/06

Ordering a Replacement Machine Identification Plate {7405, 7557}
Ordering a Replacement Machine Identification Plate {7405, 7557}

Engine News

Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12

Engine Oil Filter Element Has Metal Wrapper Instead Of Paper Wrapper
1986/03/01

Do Not Prefill Secondary Fuel Filter
1989/05/01

New 4C5084 Oil Filter Cutter Replaces Former 6V7905 Filter Cutter
1990/11/01

SOS Allowable Soot Level Changed{1318}
1994/08/01

New Oil for All Engines Burning Low-Sulfur Fuel (0.05% or less) Except The 3600 Family Of Engines{1318}
1995/02/01

New "High Efficiency" Fuel Filters Help Prevent Worn Injectors{1261}
1995/08/01

New Bench Checking And Setting Procedure For Fuel Ratio Control (FRC) Mechanical Goverened Engines{1264,1265}
1996/07/22

New Service Tool Calibration Pins For Mechanical Goverened Engines{1264,1265}
1996/07/22

New Fuel Filtration System Available {1261,1263,1274}
1998/01/20

8N-4617 Air Cleaner Clamp Kit Available{1051}
1998/03/01

Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01

New High Efficiency Oil Filters are Now Available {1308}
2004/03/01

Operation and Maintenance Manual

Engine Oil and Filter - Change
3114, 3116, and 3126 Industrial and Generator Set Engines

Fuel System Primary Filter - Clean/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines

Engine Air Cleaner Element (Dual Element) - Clean/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines

Engine Air Precleaner - Check/Clean
3114, 3116, and 3126 Industrial and Generator Set Engines

Fuel System Water Separator - Drain
3114, 3116, and 3126 Industrial and Generator Set Engines

Refill Capacities
3114, 3116, and 3126 Industrial and Generator Set Engines

Fuel Inlet Screen - Clean/Inspect/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines

Special Instruction

Caterpillar Certified Procedure to Inspect and Clean Air Filters {1051, 1054}
Caterpillar Certified Procedure to Inspect and Clean Air Filters {1051, 1054}

Service Letter-Australia

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

Service Letter-CFEL

Technical Information Bulletin

Incorrect Installation Of 146-6692 Primary Fuel Filter/Water Separator
Incorrect Installation Of 146-6692 Primary Fuel Filter/Water Separator

Specifications

Fuel Filter Base
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines

Fuel Filter and Water Separator
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines

Fuel Filter (Primary)
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines

Tool Operating Manual

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

Service Letter-China

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

Service Letter-Asia

Reuse And Salvage Guidelines

Caterpillar Certified Procedure to Inspect and Clean Air Filters {1051, 1054}
Caterpillar Certified Procedure to Inspect and Clean Air Filters {1051, 1054}

Service Letter-APD

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

Disassembly and Assembly

Fuel Priming Pump and Primary Fuel Filter - Remove and Install
3114, 3116 and 3126 Engines

Service Magazine

Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22

Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur{1318,0375,0374,1280}
1982/05/03

New Oil Additives Can Cause High Copper (Cu) Indications During S.O.S. Tests{0372,1318}
1982/09/27

Oil Filter Inspection Can Save Additional Internal Engine Damage{1318}
1985/06/17

Canister Size Of Coolant Conditioner Element Has Changed{1350}
1985/11/25

Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13

Engine Oil Filter Element Has Metal Wrapper Instead Of Paper Wrapper{1318}
1986/03/10

Field Repair Of Cooler Cores Made Of Aluminium{1063,1374,1375}
1977/09/05

Stop Engine If There Is A Turbocharger Bearing Failure{1052,1318}
1987/04/06

Do Not Use Plastic Tubing And Compression Fittings Without An Insert As A Fuel Supply Line{1274}
1978/06/26

Use Correct Procedure To Clean The Engine Lubrication System If Permanent Type Antifreeze (Ethylene Glycol) Is In The Engine{1318,1350}
1979/02/19

New Larger Capacity Water Separator Is Available{1250}
1979/03/12

Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27

Fast Fuel Delivery Couplings And Fast Oil Change Couplings Are Available For All Caterpillar Equipment{0671,1273,1279,1325}
1979/10/08

Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U.S. Factories{1318}
1979/10/15

Do Not Prefill Secondary Fuel Filter {1261,1290}
1989/05/22

New Fuel Inlet Fitting Eliminates Breakage; New Screen Used In Inlet Fitting{1250,1252,1261}
1990/03/05

Lubricant Will Ease Installation Of Secondary Radial Seal Air Filter Element {1054}
1994/04/25

SOS Allowable Soot Level Changed{1318}
1994/08/08

Be Sure To Correctly Tighten 1R-0712, 1R-0740, 1R-0749, 1R-0750, 1R-0751, 1R-0753, And 1R-0759 Fuel Filter Assemblies {1261}
1998/01/26

Engine News

Gasket Kits
1982/02/10

9U5839 Liquid Gasket Material Available For Use With Aluminum
1992/04/01

New Gasket Kits To Service Caterpillar Diesel And Natural Gas Engines
1978/08/16

Improvements to Caterpillar's Gasket Kits for Engines {7555}
2001/01/01

The Oil Pan Gasket now Requires a Gasket Sealant to be Used {1302, 7555}
2003/09/01

Repair Guidelines for Air Compressors {1803}
2003/09/01

New Oil Pan and Integral Seal {1302, 1302, 1302}
2003/10/01

A New Cylinder Head Gasket is Now Used {1100, 1124}
2008/12/29

Special Instruction

Using the 1U-7598 Seal Installation Group To Install 115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals{1160, 1161}
Using the 1U-7598 Seal Installation Group To Install 115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals{1160, 1161}

115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals{1160, 1161}
115-4109 (Dry) and 115-4120 (Wet) Crankshaft Seals{1160, 1161}

Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}

Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}

Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}

Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}

Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}

Usage of Cylinder Head Gaskets{1124}
Usage of Cylinder Head Gaskets{1124}

Determining the Correct Part Numbers for Main Bearings and Cylinder Head Gaskets{1124, 1201, 1203}
Determining the Correct Part Numbers for Main Bearings and Cylinder Head Gaskets{1124, 1201, 1203}

Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562}
Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562}

Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Technical Information Bulletin

7X-2521 Gasket Kit Includes New Oil Pan Gasket
7X-2521 Gasket Kit Includes New Oil Pan Gasket

Reuse And Salvage Guidelines

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Service Magazine

Improved Caterpillar O-ring Face Seals are Now Available {7555}
2000/05/08

Engine News

Use Of Metric Fasteners
1981/11/25

Identification Of Metric Fasteners
1987/12/01

9U5839 Liquid Gasket Material Available For Use With Aluminum
1992/04/01

8N-4617 Air Cleaner Clamp Kit Available{1051}
1998/03/01

Operation and Maintenance Manual

Standard Torque for Worm Drive Band Hose Clamps
3114, 3116, and 3126 Industrial and Generator Set Engines

Special Instruction

Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}

Chart for Heli-Coil Repair {0676}
Chart for Heli-Coil Repair {0676}

Specifications

Standard Torque for Worm Drive Band Hose Clamps
3114, 3116, and 3126 Industrial and Generator Set Engines

Truck Engine News

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}

Engine News

Interactive Self-Paced Computer Training Course Available forTechnical Marketing Information (TMI) System Users {0314}
2000/02/01

The Current Special Publication, PECP9067, "One Safe Source" Is Now Available Through The Internet {0374}
2002/05/01

The Contents Of The Service Manuals For All Commercial Engines Is Available On The Caterpillar Intranet {1000}
2002/12/01

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}

New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}

Special Instruction

Index of Repair Process Engineering Publications {0374, 1000, 7000}
Index of Repair Process Engineering Publications {0374, 1000, 7000}

Procedure for Ordering Vintage Parts {0374, 1000, 7000}
Procedure for Ordering Vintage Parts {0374, 1000, 7000}

Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}

Caterpillar Communication Regarding REACH Article 33{0374, 7000}
Caterpillar Communication Regarding REACH Article 33{0374, 7000}

Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}

Visual Service Procedures - Colors and Symbols {0374, 7000, 7006, 7960}
Visual Service Procedures - Colors and Symbols {0374, 7000, 7006, 7960}

Tool Operating Manual

9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}

439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}
439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}

Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}
Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}

Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254}
Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254}

Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}
Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}

Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}

456-4449 Support Device{0374, 0599, 0629, 0632, 0700}
456-4449 Support Device{0374, 0599, 0629, 0632, 0700}

Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}
Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}
464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}

General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}
General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}

442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}

Zip-Tie Installation Guide{0374, 0599, 7000}
Zip-Tie Installation Guide{0374, 0599, 7000}

NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}

{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}

NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}

Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}
Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}

Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}
Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}

Reuse And Salvage Guidelines

Index of Repair Process Engineering Publications {0374, 1000, 7000}
Index of Repair Process Engineering Publications {0374, 1000, 7000}

Reuse and Salvage for Mechanical Governor Groups in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI) {0374, 1000, 1050, 1250, 1300}
Reuse and Salvage for Mechanical Governor Groups in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI) {0374, 1000, 1050, 1250, 1300}

Reuse and Testing of Fuel Injection Pump Housing {0374, 1000, 1250, 1300}
Reuse and Testing of Fuel Injection Pump Housing {0374, 1000, 1250, 1300}

General Salvage and Reconditioning Techniques {0374, 1000}
General Salvage and Reconditioning Techniques {0374, 1000}

Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}

Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}

Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}

Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}

Contamination Control Guidelines

Hose Products Reference Guide {0374, 0599, 0684, 0738, 5057}
Hose Products Reference Guide {0374, 0599, 0684, 0738, 5057}

Applied Failure Analysis

Failure Analysis Report - AFA Good Report {0374, 1000}
Failure Analysis Report - AFA Good Report {0374, 1000}

Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000}
Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000}

Product Evaluation Report - AFA Bad Report {0374, 1000}
Product Evaluation Report - AFA Bad Report {0374, 1000}

Technical Analysis

Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}

Service Magazine

Interactive Self-Paced Computer Training Course Available forTechnical Marketing Information (TMI) System Users {0314}
2000/01/31

The Current Special Publication, PECP9067, "One Safe Source" Is Now Available Through The Internet {0374}
2002/05/13

Announcing the Combination of Groups Within the Paper Copies of the Caterpillar Parts Manuals {0374}
2002/06/03

Recent Changes to the R134a Refrigerant Air Conditioning Manuals Are Now Available for All Caterpillar Products {0374, 1802, 1805, 1807, 1808, 1809, 7309, 7320, 7322, 7343}
2014/07/17

A New Tool Operating Manual for Proper Zip-Tie Installation Is Now Available for All Caterpillar Products {0374, 0599, 7000}
2015/08/10

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/28

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}

New Service Information Content Is Now Available in Channel 1 {0374, 7000}
New Service Information Content Is Now Available in Channel 1 {0374, 7000}

Engine News

Why Engines Are Damaged By Fuel Sulfur
1979/08/22

Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur
1982/05/12

Caterpillar Recommends Against The Use Of Alcohol Mist Injection Systems
1982/08/25

New Oil Additives Can Cause High Copper (Cu) Indications During S.O.S. Tests
1982/09/22

Fuel Sulfur Analyzer Available
1986/01/01

High Silicates In Antifreeze
1986/02/01

Oil Total Base Number (TBN) Test Kit Available
1986/02/01

New 8T2998 Lubricant Available
1986/03/01

High Silicates In Antifreeze
1986/03/01

Caterpillar Antifreeze Now Used And Available From Parts Departments
1986/11/01

Easy Five-Minute Coolant Conditioner Test With 8T5296 Coolant Conditioner Test Kit
1987/04/01

Cooling System Conditioner
1987/04/01

Analyzing Caterpillar And Competitive Antifreezes For Amount Of Silicates
1988/02/01

New Publication Available-"Diesel Fuels And Your Engine"
1988/03/01

Extraction Tools For "Live Oil Sampling"
1988/05/01

Lubricant Supplement Lists Specifications For CXP Lubricants
1988/06/01

SOS Allowable Soot Level Changed{1318}
1994/08/01

New Oil for All Engines Burning Low-Sulfur Fuel (0.05% or less) Except The 3600 Family Of Engines{1318}
1995/02/01

Caterpillar Long Life Coolant/Antifreeze Identification{1395}
1995/07/01

A New Edition of the Special Publication, SEBD0640, "Oil and Your Engine" is Available {1348}
2001/11/01

Understanding Elevated Copper Levels in Used Oil Samples {1348, 7542}
2003/02/01

The Oil Pan Gasket now Requires a Gasket Sealant to be Used {1302, 7555}
2003/09/01

Special Publication, SEBU6251, "Caterpillar Commercial Diesel Engine Fluids Recommendations" has been Revised {0645, 1000, 1250, 1280, 1300, 1348, 1350, 1395}
2004/05/01

Caterpillar Extended Life Inhibitor (ELI) Is Now Available for Use in Applications that Freeze Protection Is Not Needed {1350, 1352, 1395}
2010/10/06

Operation and Maintenance Manual

Lubricant Information
3114, 3116, and 3126 Industrial and Generator Set Engines

Engine Oil
3114, 3116, and 3126 Industrial and Generator Set Engines

Lubricating Grease
3114, 3116, and 3126 Industrial and Generator Set Engines

S·O·S Oil Analysis
3114, 3116, and 3126 Industrial and Generator Set Engines

General Coolant Information
3114, 3116, and 3126 Industrial and Generator Set Engines

Coolant Recommendations
3114, 3116, and 3126 Industrial and Generator Set Engines

Extended Life Coolant (ELC)
3114, 3116, and 3126 Industrial and Generator Set Engines

Commercial Heavy-Duty Coolant/Antifreeze and SCA
3114, 3116, and 3126 Industrial and Generator Set Engines

Diesel Engine Antifreeze/Coolant (DEAC)
3114, 3116, and 3126 Industrial and Generator Set Engines

Conventional Coolant/Antifreeze Cooling System Maintenance
3114, 3116, and 3126 Industrial and Generator Set Engines

Supplemental Coolant Additive (SCA)
3114, 3116, and 3126 Industrial and Generator Set Engines

Water/Supplemental Coolant Additive (SCA)
3114, 3116, and 3126 Industrial and Generator Set Engines

Extended Life Coolant (ELC) Cooling System Maintenance
3114, 3116, and 3126 Industrial and Generator Set Engines

Cooling System Supplemental Coolant Additive (SCA) - Test/Add
3114, 3116, and 3126 Industrial and Generator Set Engines

Cooling System Coolant Extender (ELC) - Add
3114, 3116, and 3126 Industrial and Generator Set Engines

Engine Oil Sample - Obtain
3114, 3116, and 3126 Industrial and Generator Set Engines

Cooling System Coolant Level - Check
3114, 3116, and 3126 Industrial and Generator Set Engines

Engine Oil and Filter - Change
3114, 3116, and 3126 Industrial and Generator Set Engines

Cooling System Coolant (ELC) - Change
3114, 3116, and 3126 Industrial and Generator Set Engines

Cold Weather Lubricants
3114, 3116, and 3126 Industrial and Generator Set Engines

Refill Capacities
3114, 3116, and 3126 Industrial and Generator Set Engines

Fan Drive Bearing - Lubricate - If Equipped
3114, 3116, and 3126 Industrial and Generator Set Engines

Special Instruction

Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}

Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}

The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}

Instructions for Use of Cat Coolant Conditioner for Aluminum Components {1350, 1352, 1395}
Instructions for Use of Cat Coolant Conditioner for Aluminum Components {1350, 1352, 1395}

Tool Operating Manual

NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}

370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}

Service Magazine

Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22

Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur{1318,0375,0374,1280}
1982/05/03

Caterpillar Recommends Against The Use Of Alcohol Mist Injection Systems{1050,1250}
1982/06/28

New Oil Additives Can Cause High Copper (Cu) Indications During S.O.S. Tests{0372,1318}
1982/09/27

Canister Size Of Coolant Conditioner Element Has Changed{1350}
1985/11/25

Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13

Oil Total Base Number (TBN) Test Kit Available{1300}
1986/01/20

High Silicates In Antifreeze{1350}
1986/02/03

New 8T2998 Lubricant Available{0645,1210}
1986/02/17

Engine Oil Filter Element Has Metal Wrapper Instead Of Paper Wrapper{1318}
1986/03/10

Caterpillar Antifreeze Now Used And Available From Parts Departments{1350,1395}
1986/11/10

Easy Five-Minute Coolant Conditioner Test With 8T5296 Coolant Conditioner Test Kit{1395,0786}
1987/03/23

Cooling System Conditioner{1395,1350}
1987/03/23

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Stop Engine If There Is A Turbocharger Bearing Failure{1052,1318}
1987/04/06

Analyzing Caterpillar And Competitive Antifreezes For Amount Of Silicates{1350,1395}
1988/02/22

New Publication Available-"Diesel Fuels And Your Engine"{0374,0375,0645}
1988/03/21

Extraction Tools For "Live Oil Sampling"{7770,0770,0781,0783,0784}
1988/04/18

Installation Of Valves For Live Oil Sampling{7770,0770,0781,0783,0784}
1988/06/06

Use Correct Procedure To Clean The Engine Lubrication System If Permanent Type Antifreeze (Ethylene Glycol) Is In The Engine{1318,1350}
1979/02/19

Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27

Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U.S. Factories{1318}
1979/10/15

Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17

New Engine Wall Charts Give Maintenance Management Recommendations{0374,0375,7500,7557,7580}
1989/03/06

Engine Coolant Can Be Recycled{1395}
1989/11/13

New Cooling System Cleaner Now Available For All Engines{1350,0680,1352,1353}
1989/12/25

SOS Allowable Soot Level Changed{1318}
1994/08/08

A New Quick Coupler is Required to Extend the Service Life of Dual Purpose Valves {6129, 7542}
2002/01/21

A New Edition of the Special Publication, SEBD0640, "Oil and Your Engine" is Available {1348}
2001/11/19

Color Coded Dust Caps for S·O·S Ports Will Be Available {7770}
2002/04/01

Recent Changes to the R134a Refrigerant Air Conditioning Manuals Are Now Available for All Caterpillar Products {0374, 1802, 1805, 1807, 1808, 1809, 7309, 7320, 7322, 7343}
2014/07/17

Truck Engine News

The Product Structure Link In The Service Information System (SIS) Has Been Changed For Service Letters That Address Parts Stock Distribution {1000, 7750}
2001/08/01

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Engine News

Protect Your Reconditioned Or Rebuilt Engines During Start-Up
1980/10/01

Double-Check Those Dimensions
1980/11/12

Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12

Changes Have Been Made To Caterpillar Service Literature
1981/03/04

"SIRS User Instructions" Available
1982/02/24

Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/04/07

Hunting Down The Cheaters
1985/06/01

Keeping The Product Information System Up-To-Date
1985/10/01

Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers
1986/03/01

Engine Oil Filter Element Has Metal Wrapper Instead Of Paper Wrapper
1986/03/01

New Index Lists Engine Special Instructions By SMCS Code
1986/04/01

List of Service Publications
1986/05/01

Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01

Three Types Of Maintenance Management Publications Available For Engines
1986/06/01

Changes Have Been Made To 0T Microfiche (Fuel Setting And Related Information)
1986/07/01

More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01

List of Service Publications
1986/10/01

Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals
1986/11/01

Check For Dirt Before Replacing Pyrometer Switch
1987/01/01

List of Service Publications
1987/02/01

List of Service Publications
1987/08/01

List of Service Publications
1988/01/01

List of Service Publications
1988/04/01

List of Service Publications
1988/10/01

New Engine Wall Charts Give Maintenance Management Recommendations
1989/03/01

"Ugly's Electrical-References" SEBD0983, Now Available
1990/06/01

List of Service Publications
1990/10/01

List of Service Publications{0374,0375}
1991/03/01

List of Service Publications
1991/06/01

List of Service Publications
1991/08/01

List of Service Publications{0374,0375}
1991/12/01

List of Service Publications
1992/02/01

List of Service Publications
1992/10/01

List of Service Publications
1993/03/01

List of Service Publications
1993/08/01

New Oil for All Engines Burning Low-Sulfur Fuel (0.05% or less) Except The 3600 Family Of Engines{1318}
1995/02/01

Returning Core Engines For Full Refund {0374}
1995/03/01

Troubleshooting Information{7569}
1996/06/12

New Troubleshooting Guide Available{0374}
1997/11/14

Safety Vent Caps For Caterpillar Batteries
1977/07/13

New Color For Fiche In Engine Numerical Parts Record Library
1978/07/05

New Gasket Kits To Service Caterpillar Diesel And Natural Gas Engines
1978/08/16

Tips For Service Information Retrieval System (SIRS) Users
1978/11/15

Interactive Self-Paced Computer Training Course Available forTechnical Marketing Information (TMI) System Users {0314}
2000/02/01

The Product Structure Link In The Service Information System (SIS) Has Been Changed For Service Letters That Address Parts Stock Distribution {1000, 7750}
2001/09/01

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Operation and Maintenance Manual

Ordering Replacement Parts
3114, 3116, and 3126 Industrial and Generator Set Engines

Customer Assistance
3114, 3116, and 3126 Industrial and Generator Set Engines

Hoses and Clamps - Inspect/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines

Walk-Around Inspection
3114, 3116, and 3126 Industrial and Generator Set Engines

Overhaul Considerations
3114, 3116, and 3126 Industrial and Generator Set Engines

Special Instruction

Use Of 6V3025 Battery Cable Repair Kit{0613, 1400}
Use Of 6V3025 Battery Cable Repair Kit{0613, 1400}

Chart for Heli-Coil Repair {0676}
Chart for Heli-Coil Repair {0676}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

398-6786 Recommended J Series Flush Mount/Abrasion Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}
398-6786 Recommended J Series Flush Mount/Abrasion Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}

Caterpillar Communication Regarding REACH Article 33{0374, 7000}
Caterpillar Communication Regarding REACH Article 33{0374, 7000}

Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}

Visual Service Procedures - Colors and Symbols {0374, 7000, 7006, 7960}
Visual Service Procedures - Colors and Symbols {0374, 7000, 7006, 7960}

Service Letter-Australia

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

Service Letter-CFEL

Service Letter-China

Service Letter-Asia

Reuse And Salvage Guidelines

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Service Letter-APD

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

Technical Analysis

Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}

Service Magazine

Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22

Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03

Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur{1318,0375,0374,1280}
1982/05/03

New Address For Repair Of Diagnostic Tools{0650}
1982/06/14

New Oil Additives Can Cause High Copper (Cu) Indications During S.O.S. Tests{0372,1318}
1982/09/27

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

Engine Information Plate Contains More Data; Use Of Performance Specifications{1250,7557}
1985/10/28

Canister Size Of Coolant Conditioner Element Has Changed{1350}
1985/11/25

Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13

Engine Oil Filter Element Has Metal Wrapper Instead Of Paper Wrapper{1318}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Three Types Of Maintenance Management Publications Available For Engines{0374}
1986/06/09

New 5P7307 Engine Turning Tool Group Fits All Engines{0611}
1977/02/14

Improved 5P3000 Engine And Transmission Shipping Stand Assembly; Modification Available For Stands Already In Use{0640}
1977/04/25

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

Tools Now Available To Ream And/Or Hone 0.500" (12.70 mm) Diameter Valve Guides{0663}
1977/08/22

Polarity Connections And Use Of Service Meter Films When Service Meter Kits Are Installed{7480,7000}
1987/02/16

Check For Plugged Orifices In Mechanical Pressure Gauges{7450}
1987/03/02

Stop Engine If There Is A Turbocharger Bearing Failure{1052,1318}
1987/04/06

Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12

Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25

Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16

Analyzing Caterpillar And Competitive Antifreezes For Amount Of Silicates{1350,1395}
1988/02/22

New Publication Available-"Diesel Fuels And Your Engine"{0374,0375,0645}
1988/03/21

Extraction Tools For "Live Oil Sampling"{7770,0770,0781,0783,0784}
1988/04/18

Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22

Use Correct Procedure To Clean The Engine Lubrication System If Permanent Type Antifreeze (Ethylene Glycol) Is In The Engine{1318,1350}
1979/02/19

9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28

A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28

Caution Label Added To 5P4150 Nozzle Testing Group{0651}
1979/07/09

Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27

Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U.S. Factories{1318}
1979/10/15

Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17

New Publication Available-"Coolant And Your Engine"{1395,0374,0375}
1989/02/13

New Engine Wall Charts Give Maintenance Management Recommendations{0374,0375,7500,7557,7580}
1989/03/06

Preventive Maintenance For Batteries{1401}
1989/03/27

Do Not Prefill Secondary Fuel Filter {1261,1290}
1989/05/22

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Hand Tool List For 3114 And 3116 Engines{0600,0701}
1989/10/23

Engine Coolant Can Be Recycled{1395}
1989/11/13

New Cooling System Cleaner Now Available For All Engines{1350,0680,1352,1353}
1989/12/25

New Fuel Inlet Fitting Eliminates Breakage; New Screen Used In Inlet Fitting{1250,1252,1261}
1990/03/05

Lubricant Will Ease Installation Of Secondary Radial Seal Air Filter Element {1054}
1994/04/25

Returning Core Engines For Full Refund {0374}
1995/02/20

Interactive Self-Paced Computer Training Course Available forTechnical Marketing Information (TMI) System Users {0314}
2000/01/31

Service Information System Product Structure Link Change for Service Letters that Address Parts Stock Distribution {1000, 7000, 7750}
2001/08/20

Correction to Service Magazine , "Use the Technical Information Feedback Systems" {0374}
2001/12/03

A New Quick Coupler is Required to Extend the Service Life of Dual Purpose Valves {6129, 7542}
2002/01/21

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}

New Service Information Content Is Now Available in Channel 1 {0374, 7000}
New Service Information Content Is Now Available in Channel 1 {0374, 7000}

Engine News

Use Only Paint To Mark Connecting Rod Caps For Torque-Turn Method
1987/06/01

Service Magazine

Use Only Paint To Mark Connecting Rod Caps For Torque-Turn Method {1218,1219}
1987/06/01

New Engine Wall Charts Give Maintenance Management Recommendations{0374,0375,7500,7557,7580}
1989/03/06

Engine News

Engine Storage; Engine Start-Up After Storage
1982/02/24

Special Instruction

Procedure for Ordering Vintage Parts {0374, 1000, 7000}
Procedure for Ordering Vintage Parts {0374, 1000, 7000}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Australia

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-CFEL

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-CSARL

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Americas

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Brazil

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Truck/Ag/Marine

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-China

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Asia

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-APD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines
All 6I4783 Fuel Filters Need To Be Removed From Parts Stock And Machines In Dealer Inventory Equipped With 3116 Engines

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Magazine

Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18

Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22

New Bearing Standard: Quantity Of One Part Number Now Has Both Halves Of The Bearing{7551}
1982/08/09

Self-Exciting Alternator May Not Charge After Periods Of Storage{1405,1406}
1991/09/23

Special Instruction

Use Of Preventive Maintenance Kits{7501}
Use Of Preventive Maintenance Kits{7501}

Service Magazine

Preventive Maintenance For Batteries{1401}
1989/03/27

Engine News

Revision To Guideline For Reusable Parts Is Available
1979/03/14

Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning
1979/08/22

Protect Your Reconditioned Or Rebuilt Engines During Start-Up
1980/10/01

Reuse Of Engine Bearings
1983/05/25

Reuse Of Engine Bearings
1983/11/30

Special Instructions Packaged With Turbocharger Cartridge Repair Kits May Be Incorrect
1986/02/01

Increase Piston Reuse With Keystone Piston Ring Gauge Group
1986/07/01

Salvage Of Turbocharger Compressor Housing During Reconditioning
1978/10/18

Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}

Special Instruction

Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Tool Operating Manual

439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}
439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}

Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}
Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}

Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}

464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}
464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}

442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}

NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}

{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}

Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}
Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}

Reuse And Salvage Guidelines

Fundamentals of Arc Spray for Reconditioning Components {0679}
Fundamentals of Arc Spray for Reconditioning Components {0679}

Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}
Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Thermal Spray Procedures for Engine Front Cover{0679, 1150, 1151, 1162}
Thermal Spray Procedures for Engine Front Cover{0679, 1150, 1151, 1162}

Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}

Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}
Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}

Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}

Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}

Service Magazine

Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08

Reuse Of Engine Bearings{1230}
1983/05/16

Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21

Special Instructions Packaged With Turbocharger Cartridge Repair Kits May Be Incorrect{1053}
1986/02/03

Increase Piston Reuse With Keystone Piston Ring Gauge Group{1214,1215}
1986/06/16

Salvage Of Cylinder Heads By Using Oversized Valve Guides And Valve Inserts {1104,1103}
1987/03/30

New Information On Reusable Cylinder Liners{1216}
1978/06/19

Salvage Of Turbocharger Compressor Housing During Reconditioning{1052}
1978/10/09

A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28

Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20

Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}

Truck Engine News

A Guide to Reman Product Markings is Now Available {7754}
2015/09/18

Engine News

In The Future, Oversize And Undersize Connecting Rod And Main Bearings Will Have Size Identification Marks In Metric Units
1980/07/09

Remanufactured Undersize Crankshafts Are Available
1984/04/11

Substantial Price Reduction For Caterpillar Remanufactured Short Blocks
1985/06/01

Substantial Price Reduction For Caterpillar Remanufactured Short Blocks
1985/08/01

Why Choose Caterpillar Remanufactured Crankshafts? Because We Offer More ...
1985/09/01

Remanufactured Heavy-Duty Starters And High-Amp Alternators
1987/06/01

Oversize Pistons Not Available
1993/04/01

A Guide to Reman Product Markings is Now Available {7754}
2015/09/17

Special Instruction

Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}

Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}

A Guide to Cat® Reman Product Markings {7754}
A Guide to Cat^® Reman Product Markings {7754}

Service Letter-NACD

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Tool Operating Manual

NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}

Service Letter-China

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Asia

Reuse And Salvage Guidelines

Fundamentals of Arc Spray for Reconditioning Components {0679}
Fundamentals of Arc Spray for Reconditioning Components {0679}

Thermal Spray Procedures for Engine Front Cover{0679, 1150, 1151, 1162}
Thermal Spray Procedures for Engine Front Cover{0679, 1150, 1151, 1162}

Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}
Reuse and Salvage for Gear Train and Gear Shafts on Engines {0679, 1151, 1162, 1206}

Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}

Service Letter-APD

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Magazine

Remanufactured Undersize Crankshafts Are Available{1202}
1983/11/21

Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25

New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads{1105,1101}
1990/10/08

Oversize Pistons Not Available{1214,1216}
1993/04/05

A Guide to Reman Product Markings is Now Available {7754}
2015/09/15

Technical Information Bulletin

Engine Shipping Stands With Improper Welds For Certain 3116, 3126, C7, C9 Reman Engines {7505}
Engine Shipping Stands With Improper Welds For Certain 3116, 3126, C7, C9 Reman Engines {7505}

Service Magazine

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Improved 5P3000 Engine And Transmission Shipping Stand Assembly; Modification Available For Stands Already In Use{0640}
1977/04/25

New Engine Wall Charts Give Maintenance Management Recommendations{0374,0375,7500,7557,7580}
1989/03/06

Truck Engine News

New Infrared Thermometer Has Narrow, 50:1 Target Ratio, Wide Temperature Range {0776, 1350, 3000, 4000, 4150, 4250}
2006/03/27

Engine News

New 6V87 Gauge Measures Valve Stem Wear
1979/01/10

New 6V2120 Spline Sprocket Improves Depth Control Of 5P4175 Boring Tool Group
1980/05/14

6V3150 Engine Pressure Group And 6V3121 Multitach Group Are Available For Testing Engines
1981/01/28

Changes Have Been Made To Caterpillar Service Literature
1981/03/04

Instruction Cards For "Go-No Go" Gauges Now Available
1981/07/01

New Engine Testing And Adjusting Tools Give More Accuracy And Longer Service Life
1982/02/24

Use 6V6035 Hardness Tester On Crankshafts
1982/02/24

Use The 6V6059 Microlite With The 6V2196 Inspection Microscope
1982/04/07

Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/04/07

New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach
1982/05/12

New Address For Repair Of Diagnostic Tools
1982/06/16

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25

Separate Valve Stem Gauges Available
1982/08/25

Dial Bore Gauge And Size Setting Fixture Available
1982/09/22

Service Information For Easier Use Of The 6V3100 Timing Indicator Group
1982/10/20

Make Change To 6V2100 Multitach And 5P9698 Calibrator
1982/12/15

Use FT1711 Light Table For Cylinder Liner Inspection
1982/12/15

New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip
1982/12/15

Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15

Use The 6V5000 Infrared Thermometer Group To Measure Temperatures
1983/04/27

New Service Centers For 6V3100 Engine Timing Indicator Group
1983/10/26

Hunting Down The Cheaters
1985/06/01

Fuel Sulfur Analyzer Available
1986/01/01

Oil Total Base Number (TBN) Test Kit Available
1986/02/01

New Engine Timing Indicator Group Available
1986/07/01

Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01

New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity
1986/11/01

Check For Dirt Before Replacing Pyrometer Switch
1987/01/01

Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups
1987/03/01

Check For Plugged Orifices In Mechanical Pressure Gauges
1987/03/01

5P957 And 5P3514 Coolant And Battery Tester
1987/04/01

Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems
1987/05/01

Two New Self-Powered Digital Tachometers And Signal Generator Available
1987/05/01

Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group
1987/07/01

Fluid Sampling Tools For Nonpressurized Compartments
1988/03/01

Extraction Tools For "Live Oil Sampling"
1988/05/01

New Service Tools Available
1988/10/01

Vibration Measurement System For Caterpillar Products
1989/06/01

Use Correct Calibration Pin (1U9786) When Calibrating Governor; Do Not Use 1U7305 Insertion Tool
1989/11/01

Hand Tool List For 3114 And 3116 Engines
1989/11/01

New 4C5084 Oil Filter Cutter Replaces Former 6V7905 Filter Cutter
1990/11/01

Modification Of 1U7791 Valve Seat Driver
1990/11/01

New 9U6101 Lower Pilot Reamer Group Available
1993/02/01

Improved 1U-7430 Front Crankshaft Seal Installer Available{1160}
1995/08/01

Fuel Injector Sleeve Replacement Tooling{0703,1125}
1996/02/16

New Service Tool Calibration Pins For Mechanical Goverened Engines{1264,1265}
1996/07/22

Governor Shimming Is Determined By The Governor Test Bench Calibration{1264,1289}
1996/07/22

New 173-1530 Injector Seating Tool Group Available{0710,1290}
1999/09/01

5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster
1978/01/18

Caterpillar Electronic Technician (Cat ET) 2001B-Service Pack 1 Software Upgrade is Now Available {0785}
2002/02/01

Do not Use the 1U-6661 Pop Tester Gp to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/24

Do not Use the 1U-6661 Pop Tester Gp or the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/24

Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01

Do not Use the 1U-6661 Pop Tester Gp or the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01

Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}

Special Instruction

Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement^*{0781, 0782}

Using The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement^*{0781, 0782}

Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}
Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}

Using The 5P-4150 Nozzle Testing Group{0782}
Using The 5P-4150 Nozzle Testing Group{0782}

Using The 4S6553 Engine Evaluation Test Group{0781}
Using The 4S6553 Engine Evaluation Test Group{0781}

Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}

6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569}
6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569}

Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}

Using The 6V4950 Injection Line Speed Pickup Group{0782}
Using The 6V4950 Injection Line Speed Pickup Group{0782}

Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}

Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}
Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}

Using 8S2305, 9S228, And 6V9128 Rack Position Tool Groups{0782, 1250}
Using 8S2305, 9S228, And 6V9128 Rack Position Tool Groups{0782, 1250}

Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}

Using Caterpillar Cylinder Pack Pulling Tools{1239}
Using Caterpillar Cylinder Pack Pulling Tools{1239}

Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}

Using The 8T1000 Position Indicator Group{0760, 0762}
Using The 8T1000 Position Indicator Group{0760, 0762}

Using the 1U6602 Photo-Tach Group{0775}
Using the 1U6602 Photo-Tach Group{0775}

Using the 1U7326 Governor Calibration Bench{1264, 0778}
Using the 1U7326 Governor Calibration Bench{1264, 0778}

Using the 1U5470 Engine Pressure Group{0781}
Using the 1U5470 Engine Pressure Group{0781}

Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}

Using the 127-3458 Sleeve Replacement Tool Group{1290}
Using the 127-3458 Sleeve Replacement Tool Group{1290}

Using the 4C6821 Injection Line Speed Pickup Group{0781}
Using the 4C6821 Injection Line Speed Pickup Group{0781}

Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}

Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}

Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}

Operation And Maintenance Of 1P3060 Pyrometer Group{0776}
Operation And Maintenance Of 1P3060 Pyrometer Group{0776}

Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}

Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}

Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}

Use Of 8T0455 Cylinder Liner Projection Indicator Group{0760, 1216}
Use Of 8T0455 Cylinder Liner Projection Indicator Group{0760, 1216}

Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}

Using The 6V7899 Size Setting Fixture Group{651}
Using The 6V7899 Size Setting Fixture Group{651}

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

Tool and Specification Chart for Inverted Duo-Cone Seals {0599, 7561}
Tool and Specification Chart for Inverted Duo-Cone Seals {0599, 7561}

Using Caterpillar Replacement Thread Inserts {0676}
Using Caterpillar Replacement Thread Inserts {0676}

Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}

Operating Instructions for Cat 1U-9400 Series Hydraulic Test Center {0784}
Operating Instructions for Cat 1U-9400 Series Hydraulic Test Center {0784}

Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}

Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474}
Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Tool Operating Manual

Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes

Instructions for 1U9801 Ultrasonic Wear Indicator Program Module Replacement{0767}
Instructions for 1U9801 Ultrasonic Wear Indicator Program Module Replacement{0767}

Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}
Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}

358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684}
358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684}

Crimputer III Setup and Operation{0684, 5057}
Crimputer III Setup and Operation{0684, 5057}

NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}

9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}

NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}

370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}

439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}
439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}

NEHS0566 4C-9832 Large Engine Roll-Over Stand {0599, 0701}
NEHS0566 4C-9832 Large Engine Roll-Over Stand {0599, 0701}

Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}
Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}

Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254}
Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254}

185-5321 Cylinder Head Lifting Hook Assembly{0599, 0632, 0703, 1101, 6459}
185-5321 Cylinder Head Lifting Hook Assembly{0599, 0632, 0703, 1101, 6459}

Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}
Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}

Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}

456-4449 Support Device{0374, 0599, 0629, 0632, 0700}
456-4449 Support Device{0374, 0599, 0629, 0632, 0700}

Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}
Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}
464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}

General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}
General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}

442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}

Zip-Tie Installation Guide{0374, 0599, 7000}
Zip-Tie Installation Guide{0374, 0599, 7000}

NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}

{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}

NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}

M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}

Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}
Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}

Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}
Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}

Reuse And Salvage Guidelines

Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}

Dynamometer Testing of Caterpillar Engines {0781, 1000}
Dynamometer Testing of Caterpillar Engines {0781, 1000}

Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685}
Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685}

Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}

Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}

Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}

Crimputer III Setup and Operation{0684, 5057}
Crimputer III Setup and Operation{0684, 5057}

Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}

Fundamentals of HVOF Spray for Reconditioning Components {0599, 0679, 1000, 7000}
Fundamentals of HVOF Spray for Reconditioning Components {0599, 0679, 1000, 7000}

Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}
Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}

Cleaning Components with Carbon Dioxide (CO2) {0680, 1000, 7000}
Cleaning Components with Carbon Dioxide (CO₂) {0680, 1000, 7000}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}

Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}

Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}

Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}

Shop Review

Engine Component Racks
Engine Component Racks

Engine Stands
Engine Stands

Bench Test Procedures

Dynamometer Testing of Caterpillar Engines {0781, 1000}
Dynamometer Testing of Caterpillar Engines {0781, 1000}

Technical Analysis

Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}

Service Magazine

Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17

Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18

New Engine Testing And Adjusting Tools Give More Accuracy And Longer Service Life{0651}
1982/02/01

Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22

Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03

Separate Valve Stem Gauges Available{0653,1000}
1982/06/07

New Address For Repair Of Diagnostic Tools{0650}
1982/06/14

6V6124 Calibration Coil Available To Calibrate And Check 6V4910 AC/DC Clamp-On Ammeter{0651}
1982/06/28

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16

Vacuum Tester Checks For Leaks Between Valve Face and Seat{0651,1103,1105}
1982/09/06

Dial Bore Gauge And Size Setting Fixture Available{0653}
1982/09/20

Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11

Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08

Make Change To 6V2100 Multitach And 5P9698 Calibrator{0651}
1982/11/15

Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22

New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29

Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13

Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16

New Engine Timing Indicator Group Available {0781,0782}
1986/07/07

New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27

Use Gas Detector Tubes That Have Expired Dates To "Break In" The Combustion Chambers For The Fuel Sulphur Analyzer Group{0651}
1986/11/10

Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15

New Special Instruction For Troubleshooting 5P2150 Engine Horsepower Meter{0651,1250}
1977/01/17

New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17

New 5P7307 Engine Turning Tool Group Fits All Engines{0611}
1977/02/14

Tools Now Available To Ream And/Or Hone 0.500" (12.70 mm) Diameter Valve Guides{0663}
1977/08/22

Troubleshooting The Tachometer System Of The 4S6553 Engine Instrument Group{0651}
1977/10/10

Fabricated Extension Prevents Fuel "Splash" During Injection Valve Testing{0650,1254}
1977/10/17

Assembly Procedure For The 5P4721 Tube (Part Of The 5P4149 Conversion Group And 5P4150 Nozzle Testing Group){0650}
1977/10/24

With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31

Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems {0774,1250,1300,1350}
1987/05/11

The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11

Two New Self-Powered Digital Tachometers And Signal Generator Available {7462}
1987/05/11

Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20

Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06

5P4149 Conversion Group To Become A Discontinued Item On October 1, 1978{0650,1254}
1978/03/27

Locating Bushings For The 5P3550 Rod Boring Machine Will Now Hold Tapered Piston Pin Bushings {0626}
1978/04/17

Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

New 5P8744 Adapter Assembly And Special Instruction Procedures For 5P4150 Nozzle Tester Group{0650}
1978/08/28

New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11

Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25

Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25

4J7533 O-Ring Seals Now Available For Parts Service Of The 5P4150 Nozzle Tester Group{0651}
1978/10/09

Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16

Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16

New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04

Extraction Tools For "Live Oil Sampling"{7770,0770,0781,0783,0784}
1988/04/18

Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18

New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23

Installation Of Valves For Live Oil Sampling{7770,0770,0781,0783,0784}
1988/06/06

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

New 6V87 Gauge Measures Valve Stem Wear{0653,1105}
1979/01/08

Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22

9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28

6V183 Gasket Now Available For Parts Service To Use On 5P4150 Or 8S2242 Nozzle Tester{0651}
1979/06/25

Caution Label Added To 5P4150 Nozzle Testing Group{0651}
1979/07/09

Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06

Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03

Fast Fuel Delivery Couplings And Fast Oil Change Couplings Are Available For All Caterpillar Equipment{0671,1273,1279,1325}
1979/10/08

Use The 6V2034 Micrometer Adapter To Measure Lip Thickness Of Engine Valves {0653,1105}
1979/10/29

Hand Tool List For 3114 And 3116 Engines{0600,0701}
1989/10/23

Use Correct Calibration Pin (1U9786) When Calibrating Governor; Do Not Use 1U7305 Insertion Tool{0706,0782,1264}
1989/11/06

Some 4C4462 Sleeve Removal And Installation Groups For Unit Injectors May Contain 4C5562 Reamer Assemblies That Are Dimensionally Incorrect {0782,1290}
1990/05/21

Modification Of 1U7791 Valve Seat Driver{0782,1103}
1990/10/29

Rotate Crankshaft On 3114, 3116 And 3126 Engines Using 9U-6943 Gear Shaft Housing Assembly Or 9U-7336 Gear Shaft Housing Assembly {1202,0701}
1996/12/09

128-3102 Tap Assembly And 128-3104 Stud Puller To Remove Injector Sleeves With Oversized Lower Bore {1125}
1997/01/27

Cylinder Head Stress Plate Used During Cylinder Bore Honing And Measurement {1223}
1997/01/27

Use 146-2597 Rocker Arm Bearing Installation Tool To Hold Push Rods In Place {1208}
1998/08/17

Pull the Injector Sleeve with a 139-0692 Sleeve Jaw {0706, 1713}
2000/04/17

New Hydraulic Wrenches and Pumps {0602, 0615}
2000/06/01

Diagnostic Cables and Harnesses Are Available {0785}
2000/12/25

Thermocouple Assembly (Exhaust) Measures Engine Exhaust Temperatures {0701, 0776, 0781}
2004/04/01

40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16

Do not Use the 1U-6661 Pop Tester Gp or the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/24

Do not Use the 1U-6661 Pop Tester Gp or the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01

Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562}
Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562}

A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}

A New Tool Operating Manual for Proper Zip-Tie Installation Is Now Available for All Caterpillar Products {0374, 0599, 7000}
2015/08/10

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}

Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}

Engine News

How To Obtain Correct Delivery Date For Warranty Claims
1978/10/18

Provide Proper Documentation of Returned Parts within the Warranty Claim {1000}
2004/05/01

Insulation on Exhaust Components {1000}
2006/03/06

Service Magazine

Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14

Tool Operating Manual

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

Service Magazine

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Fast Fuel Delivery Couplings And Fast Oil Change Couplings Are Available For All Caterpillar Equipment{0671,1273,1279,1325}
1979/10/08

Special Instruction

Using Caterpillar Replacement Thread Inserts {0676}
Using Caterpillar Replacement Thread Inserts {0676}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Reuse And Salvage Guidelines

Service Magazine

Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03

3116 Industrial Engine 4PG00001-UP SERVICE EQUIPMENT AND SUPPLIES Caterpillar SIS

Parts group 3116:

Information:

Truck sale: