AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

7W-8179 DRIVE GP-GOV & TRANSFER PUMP S/N 4PG1-663 PART OF 7C-6951 GOVERNOR GP-UNIT INJECTOR ALSO AN ATTACHMENT 3116


FUEL SYSTEM
GOVERNOR GP
PUMP GP-FUEL INJECTION
LINES GP-FUEL
PUMP GP-FUEL PRIMING
PUMP GP-FUEL TRANSFER
FILTER GP-FUEL

INDUSTRIAL ENGINE 3116 INDUSTRIAL ENGINE 4PG
 3116 Industrial Engine 4PG00001-UP SEBP1789 3116 4PG   (1988)

FUEL SYSTEM

GOVERNOR GP
DRIVE GP-GOV & TRANSFER PUMP
6I-0232 DRIVE GP-GOV & TRANSFER PUMP
DRIVE GP-GOV & TRANSFER PUMP
7E-8794 DRIVE GP-GOV & TRANSFER PUMP
DRIVE GP-GOV & TRANSFER PUMP
7W-8179 DRIVE GP-GOV & TRANSFER PUMP
GOVERNOR GP
101-7356 GOVERNOR GP
GOVERNOR GP
101-7356 GOVERNOR GP
GOVERNOR GP
101-7357 GOVERNOR GP
 

#SEBP17890520
 

7W-8179: DRIVE GP-GOV & TRANSFER PUMP

7W-8179 DRIVE GP-GOV & TRANSFER PUMP
S/N 4PG1-663
PART OF 7C-6951 GOVERNOR GP-UNIT INJECTOR
ALSO AN ATTACHMENT
i00416335 SEBP1789
7W8179 DRIVE GP-GOV & TRANSFER PUMP Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9M-1974 [1] WASHER-HARD (8.8X16X2-MM THK)  
2. 8T-0276 CM [1] BOLT (M8X1.25X45-MM)  
3. 9Y-7567 [1] SPRING-GOVERNOR DRIVE  
4. 9Y-0275 [1] COVER-GOVERNOR DRIVE  
5. 7W-9526 [1] SPRING-TORSION  
6. 7C-5593 [1] SPRING-THROTTLE BIAS  
7. 7W-9638 [1] SHAFT AS-SHUTOFF  
8. ZC [1] LEVER-SHUT OFF  
9. ZC [1] LEVER-SHUT OFF  
10. ZC [1] PIN-SPRING  
11. 8T-5433 CM [4] BOLT-SOCKET HEAD (M3X0.5X1.5-MM)  
12. 6V-5213 M [2] BOLT-SOCKET HEAD (M5X0.8X12-MM)  
13. 9Y-0273 [1] GEAR AS-GOVERNOR DRIVE  
14. 9Y-3289 C [1] DOWEL  
15. 4D-9986 [2] SEAL-O-RING  
16. 7W-5619 [1] PISTON AS-PUMP  
17. 7W-7379 [1] FITTING-INLET  
18. 7W-5621 [1] COVER-TRANSFER PUMP  
19. 7C-5294 [1] SPRING  
20. 8C-6364 M [3] BOLT-SOCKET HEAD (M5X0.8X14-MM)  
21. 7W-7381 [1] FITTING-OUTLET  
22. 3J-1907 [2] SEAL-O-RING  
23. 7W-7383 [2] VALVE AS-CHECK  
24. 7W-5571 [1] LEVER-CONTROL  
25. 8T-7050 M [1] SETSCREW-SOCKET (M5X0.8X12-MM)  
26. 6L-8598 [1] RING-RETAINING  
27. 7W-5568 [1] SHAFT AS-THROTTLE  
28. 7W-5615 [1] SLEEVE AS-PUMP  
29. 1W-0565 [1] RING-RETAINING  
30. 7W-5558 [1] HOUSING AS-GOVERNOR  
31. Z [1] CARRIER AS-DRIVE  
32. Z [1] DOWEL  
33. Z [2] BEARING-NEEDLE  
34. 7S-5005 [2] DOWEL  
35. 7S-6798 C [1] SEAL-LIP TYPE  
36. 9Y-0208 [1] BUSHING-TERMINAL  
37. Z [1] SHAFT  
  C   CHANGE FROM PREVIOUS TYPE
  M   METRIC PART
  Z   NOT SERVICED SEPARATELY
 

#SEBP17890521
 

7W-4812: FASTENER GP-FUEL INJ PUMP

7W-4812 FASTENER GP-FUEL INJ PUMP
PART OF 101-3186, 101-3187, 110-2395, 110-2396, 110-2397, 110-2398, 113-4895, 113-4896, 4P-1695, 4P-5527, 4P-5796, 7E-7661 GOVERNOR GP-UNIT INJECTOR
i00187773 SEBP1789
7W4812 FASTENER GP-FUEL INJ PUMP Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7W-3872 J [1] SLEEVE  
2. 9M-1974 [3] WASHER-HARD (8.8X16X2-MM THK)  
3. 6V-5218 M [3] BOLT (M8X1.25X35-MM)  
4. 9Y-5295 [1] TUBE  
5. 6F-6673 [1] SEAL-O-RING  
6. 7C-3839 [1] CLIP-SPRING  
7. 7E-0844 [1] SEAL  
8. 1T-1068 [1] SEAL-O-RING  
  J   INSTALL SLEEVE IN FRONT HOUSING
  M   METRIC PART
 

#SEBP17890522
 

149-8279: FASTENER GP-FUEL LINES

149-8279 FASTENER GP-FUEL LINES
FOR USE WITH @@@@@149-8282@@@@@, @@@@@149-8283@@@@@
AN ATTACHMENT
i00688401 SEBP1789
1498279 FASTENER GP-FUEL LINES Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6K-8178 [2] CLIP (LOOP)  
2. 8M-2773 [2] CLIP (LOOP)  
3. 8L-5449 [2] SPACER (0.375X0.75X0.69-IN THK)  
4. 3E-4352 [2] WASHER-HARD (8.8X20.5X2.5-MM THK)  
5. 6V-5219 M [2] BOLT (M8X1.25X40-MM)  
  M   METRIC PART
 

#SEBP17890523
 

149-8865: FASTENER GP-FUEL LINES

149-8865 FASTENER GP-FUEL LINES
AN ATTACHMENT
i00688455 SEBP1789
1498865 FASTENER GP-FUEL LINES Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8M-2773 [2] CLIP (LOOP)  
2. 8L-5449 [2] SPACER (0.375X0.75X0.69-IN THK)  
3. 3E-4352 [2] WASHER-HARD (8.8X20.5X2.5-MM THK)  
4. 6V-5219 M [2] BOLT (M8X1.25X40-MM)  
  M   METRIC PART
 

#SEBP17890524
 

151-5057: FASTENER GP-FUEL LINES

151-5057 FASTENER GP-FUEL LINES
FOR USE WITH @@@@@151-5056@@@@@
AN ATTACHMENT
i00688458 SEBP1789
1515057 FASTENER GP-FUEL LINES Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8M-2773 [1] CLIP (LOOP)  
2. 8L-5449 [1] SPACER (0.375X0.75X0.69-IN THK)  
3. 3E-4352 [1] WASHER-HARD (8.8X20.5X2.5-MM THK)  
4. 6V-3918 M [1] BOLT (M8X1.25X50-MM)  
  M   METRIC PART
 

#SEBP17890525
 

151-5058: FASTENER GP-FUEL LINES

151-5058 FASTENER GP-FUEL LINES
FOR USE WITH @@@@@151-5059@@@@@, LH MOUNTED FUEL FILTER AND ELECTRIC BOOST PUMP
AN ATTACHMENT
i00688459 SEBP1789
1515058 FASTENER GP-FUEL LINES Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. [1] ANGLE  
2. 149-5947 [1] ELBOW  
3. 3J-1907 [1] SEAL-O-RING  
4. [1] CLAMP  
5. 3E-4352 [3] WASHER-HARD (8.8X20.5X2.5-MM THK)  
6. 6V-5218 M [1] BOLT (M8X1.25X35-MM)  
7. 5P-7970 M [1] NUT (M8X1.25-THD)  
8. 6V-5219 M [1] BOLT (M8X1.25X40-MM)  
9. 9W-4216 [1] SPACER (9X18X7-MM THK)  
  M   METRIC PART
 

#SEBP17890526
 

172-4377: FASTENER GP-FUEL PUMP

172-4377 FASTENER GP-FUEL PUMP
FOR USE WITH LH MOUNTED FUEL FILTER AND ELECTRIC BOOST PUMP
AN ATTACHMENT
i01088156 SEBP1789
1724377 FASTENER GP-FUEL PUMP Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 096-4882 M [2] LOCKNUT (M8X1.25-THD)  
2. 7X-0603 [4] WASHER-HARD (9.9X35X2.5-MM THK)  
3. 101-9762 [2] MOUNT  
4. 8T-0276 M [2] BOLT (M8X1.25X45-MM)  
5. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
6. 172-7835 [2] CLAMP  
  M   METRIC PART
 

#SEBP17890527
 

148-6317: FASTENER GP-FUEL TRANSFER PUMP

148-6317 FASTENER GP-FUEL TRANSFER PUMP
FOR USE WITH LINES GP-FUEL FILTER
AN ATTACHMENT
i01022163 SEBP1789
1486317 FASTENER GP-FUEL TRANSFER PUMP Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. [1] CLAMP  
2. 5P-7970 M [1] NUT (M8X1.25-THD)  
3. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
4. 6V-5218 M [1] BOLT (M8X1.25X35-MM)  
5. [1] ANGLE  
6. 8T-0100 M [1] BOLT (M8X1.25X60-MM)  
7. 085-7329 [1] SPACER (9X19X30-MM THK)  
  M   METRIC PART
 

#SEBP17890528
 

112-6698: FILTER & LINES GP-FUEL

112-6698 FILTER & LINES GP-FUEL
AN ATTACHMENT
i00492646 SEBP1789
1126698 FILTER & LINES GP-FUEL Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6V-6317 M [2] BOLT (M10X1.5X20-MM)  
2. 6V-8724 [1] ELBOW  
3. 3J-1907 [5] SEAL-O-RING  
4. 8W-5425 I [1] HOSE AS  
5. 6V-8397 [6] SEAL-O-RING  
6. 8M-9024 [2] WASHER-HARD (10.2X22.5X5-MM THK)  
7. 5F-7054 [1] SEAL-O-RING  
8. 6V-2317 M [4] BOLT (M8X1.25X30-MM)  
9. 7E-5190 [1] TUBE AS  
10. 7E-5189 [1] VALVE AS (FUEL)  
11. 8T-0151 [1] ADAPTER  
12. 3S-2093 [1] STRAP-CABLE  
13. 9X-2099 M [1] STUD (M8X1.25X52.75-MM)  
14. 116-1859 [1] ELBOW  
15. 8T-5043 [1] ADAPTER  
16. 1J-9671 [1] SEAL-O-RING  
17. 9C-7323 I [1] HOSE AS  
18. 112-6521 [1] BASE AS-FUEL FILTER  
  112-6523 [1] INSERT-FUEL FILTER  
19. 6V-5839 [3] WASHER (11X21X2.5-MM THK)  
20. 9M-1974 [6] WASHER-HARD (8.8X16X2-MM THK)  
21. 5P-7970 M [2] NUT (M8X1.25-THD)  
22. 1P-0436 [1] GASKET (FUEL PRIMING PUMP)  
23. 6N-4414 [1] COVER-FILTER BASE  
24. 1B-2790 [1] BOLT (5/16-18X1.375-IN)  
25. 7B-2742 [1] BOLT (1/4-20X1.25-IN)  
26. 5P-0537 [1] WASHER-HARD (7.2X14.5X2-MM THK)  
27. 5P-7813 [1] SEAL-O-RING  
28. 3N-3252 [1] SPRING  
29. 6V-9850 [1] ELBOW  
30. 8M-2773 [2] CLIP (LOOP)  
31. 4P-2413 [1] PLATE  
32. 6V-1820 M [3] BOLT (M10X1.5X30-MM)  
33. 5P-4116 [2] WASHER-HARD (8.8X20.5X2-MM THK)  
34. 5P-1442 HOSE (140 CM)  
35. 4K-8864 [1] CLIP (LOOP)  
36. 6V-8774 [1] TEE  
37. 6V-5219 M [3] BOLT (M8X1.25X40-MM)  
38. 8L-5449 [3] SPACER (0.375X0.75X0.69-IN THK)  
39. 6K-8178 [2] CLIP (LOOP)  
40. 6I-2422 [1] VALVE AS  
41. 115-4184 [1] TEE-O-RING PORT  
42. 5P-4924 [1] ELBOW  
43. 5P-4961 [2] CLAMP-HOSE  
44. 4P-5918 [1] CLIP  
45. 039-4966 [1] ADAPTER  
46. 068-9526 [1] CAP-TUBE  
47. 5C-7261 M [1] NUT (M8X1.25-THD)  
  I   REFER TO HYDRAULIC INFORMATION SYSTEM
  M   METRIC PART
 

#SEBP17890529
 

7E-0589: FILTER & LINES GP-FUEL

7E-0589 FILTER & LINES GP-FUEL
Type 1
AN ATTACHMENT
i00397244 SEBP1789
7E0589 FILTER & LINES GP-FUEL Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8T-7934 [2] WASHER-HARD (11X21X5-MM THK)  
2. 6V-6317 M [2] BOLT (M10X1.5X20-MM)  
3. 6V-8724 [2] ELBOW  
4. 3J-1907 [4] SEAL-O-RING  
5. 7E-0156 [1] FITTING-INLET  
6. 6V-8397 [4] SEAL-O-RING  
7. 8W-5425 I [1] HOSE AS  
8. 7E-0592 [1] PLATE  
9. 002-9372 [2] CLIP  
10. 8T-5043 [1] ADAPTER  
  1J-9671 [1] SEAL-O-RING  
11. 7E-0591 [1] BASE AS-FUEL FILTER  
  9S-4167 [1] STUD-HOLLOW (1-14X1.47-IN)  
12. 7E-0155 [1] SCREEN AS-FUEL  
13. 7C-5861 [1] TUBE AS  
14. 5F-7054 [1] SEAL-O-RING  
15. 6V-2317 M [3] BOLT (M8X1.25X30-MM)  
16. 6V-5842 M [1] BOLT (M10X1.5X40-MM)  
17. 6V-5839 [2] WASHER (11X21X2.5-MM THK)  
18. 8C-8581 M [1] BOLT-HIGH TEMPERATURE (M10X1.5X30-MM)  
19. 7C-7838 [1] VALVE AS  
20. 7W-7381 [1] FITTING-OUTLET  
21. 8W-5740 I [1] HOSE AS  
22. 2T-2305 [1] ELBOW  
23. 1P-0436 [1] GASKET (FUEL PRIMING PUMP)  
24. 7B-2742 [1] BOLT (1/4-20X1.25-IN)  
  5P-0537 [1] WASHER-HARD (7.2X14.5X2-MM THK)  
25. 6N-4414 [1] COVER-FILTER BASE  
26. 1B-2790 [1] BOLT (5/16-18X1.375-IN)  
27. 9M-1974 [3] WASHER-HARD (8.8X16X2-MM THK)  
28. 5P-7970 M [1] NUT (M8X1.25-THD)  
  I   REFER TO HYDRAULIC INFORMATION SYSTEM
  M   METRIC PART
 

Information:

Engine News
Explanation Of Differences In Timing Advance Information
1981/08/26
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Use Correct Calibration Pin (1U9786) When Calibrating Governor; Do Not Use 1U7305 Insertion Tool
1989/11/01
Setscrew And Nut Available For Fuel Setting And Injector Synchronization
1990/11/01
Larger O-ring Seal Available For Oil Supply Port In Governor Housing
1991/05/01
4P6493 Governor Information Plate Available
1992/06/01
Governor Specifications Are Available Through The Technical Information System
1992/09/01
Replacement Governors For Early Engines
1992/10/01
Measuring "Dynamic Rack" Of Unit Injectors
1993/06/01
New Bench Checking And Setting Procedure For Fuel Ratio Control (FRC) Mechanical Goverened Engines{1264,1265}
1996/07/22
New Service Tool Calibration Pins For Mechanical Goverened Engines{1264,1265}
1996/07/22
Governor Shimming Is Determined By The Governor Test Bench Calibration{1264,1289}
1996/07/22
Replacing The Shutoff Assembly In Engines With Older Governors{1264,1289}
1996/07/22
Servo Assembly Parts Have Been Changed To Make Some Parts Common Between Mechanical Governed (Type I-VI) Engines{1264,1289}
1996/07/22
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Operation and Maintenance Manual
Fuel Inlet Screen - Clean/Inspect/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Using the 1U7326 Governor Calibration Bench{1264, 0778}
Using the 1U7326 Governor Calibration Bench{1264, 0778}
Governor Performance Data{1264}
Governor Performance Data{1264}
Using the 127-3458 Sleeve Replacement Tool Group{1290}
Using the 127-3458 Sleeve Replacement Tool Group{1290}
Installing the 4P-9048 Control Assembly or 102-7459 Control Assembly{1298}
Installing the 4P-9048 Control Assembly or 102-7459 Control Assembly{1298}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
Service Letter-NACD
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Vernier Control Cable Assembly
SUPPLEMENT FOR 3114, 3116 & 3126 - INDUSTRIAL ENGINES ENGINES EQUIPPED WIT
Governor Identification - Introduction
3114, 3116 and 3126 MUI Engine Governors
Governor (Type I)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type II)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type IV)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI)
3114, 3116 and 3126 MUI Engine Governors
Specification
3114, 3116 and 3126 MUI Engine Governors
Governor Performance Data
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII)
3114, 3116 and 3126 MUI Engine Governors
Governor
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines
Service Letter-China
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
Service Letter-Asia
Systems Operation
Governor Speed Circuit
3114, 3116 and 3126 MUI Engine Governors
Governor Limiting Circuit (Types I, II, III, and IV)
3114, 3116 and 3126 MUI Engine Governors
Governor Limiting Circuit (Types V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors
Fuel Ratio Control (Types I and IV)
3114, 3116 and 3126 MUI Engine Governors
Governor Servo (Types I, III, IV, V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors
Dashpot (Types I, III, IV, V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors
Governor Bias Spring (Most Types IV, V, and VI)
3114, 3116 and 3126 MUI Engine Governors
Governor Bumper Spring (Some Type IV)
3114, 3116 and 3126 MUI Engine Governors
Dual Horsepower (Type VI)
3114, 3116 and 3126 MUI Engine Governors
Dual Horsepower (Type VII)
3114, 3116 and 3126 MUI Engine Governors
Torque Limiter Device (Some Type V)
3114, 3116 and 3126 MUI Engine Governors
Information Release Memo
REMANUFACTURED GOVERNORS FOR VARIOUS 3114 AND 3116 INDUSTRIAL, MACHINE, MARINE AND ON-HIGHWAY TRUCK APPLICATIONS
REMANUFACTURED GOVERNORS FOR VARIOUS 3114 AND 3116 INDUSTRIAL, MACHINE, MARINE AND ON-HIGHWAY TRUCK APPLICATIONS
PRODUCT LINE ADDITION: REMAN 3524B HAA ENGINE AVAILABLE FOR 797A & 797B TRUCKS
PRODUCT LINE ADDITION: REMAN 3524B HAA ENGINE AVAILABLE FOR 797A & 797B TRUCKS
Service Letter-APD
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
Testing and Adjusting
Prepare Calibration Bench for Test Procedure
3114, 3116 and 3126 MUI Engine Governors
Installation of Governor on 1U7326 Governor Calibration Bench
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Setting the Governor Load Stop Dimension for More Than 9.00 mm
3114, 3116 and 3126 MUI Engine Governors
Governor (Types I, II, IV, and V) - Check
3114, 3116 and 3126 MUI Engine Governors
Throttle Lever Orientation (Types IV, V, VI, VII, and Some III) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Types I, II, and Some III) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Governor (Types IV and Some III) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Throttle Lever (Types IV, V, VI, VII, and Some III) - Remove
3114, 3116 and 3126 MUI Engine Governors
Throttle Lever (Types IV, V, VI, VII, and Some III) - Install
3114, 3116 and 3126 MUI Engine Governors
Governor - Adjust
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines
Troubleshooting
Governor Instability
3114, 3116 and 3126 Engines
Disassembly and Assembly
Governor (Type I) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type I) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type IV) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type IV) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type II) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type II) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor - Install
3114, 3116 and 3126 Engines
Governor - Remove
3114, 3116 and 3126 Engines
Service Magazine
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Use Correct Calibration Pin (1U9786) When Calibrating Governor; Do Not Use 1U7305 Insertion Tool{0706,0782,1264}
1989/11/06
Some 4C4462 Sleeve Removal And Installation Groups For Unit Injectors May Contain 4C5562 Reamer Assemblies That Are Dimensionally Incorrect {0782,1290}
1990/05/21
Engine Rack Control Assemblies Improved {1257}
1990/07/02
New Fuel Setting Screw Cover And Bolt {1257}
1990/07/02
Setscrew And Nut Available For Fuel Setting And Injector Synchronization {1257}
1990/10/22
Larger O-ring Seal Available For Oil Supply Port In Governor Housing{1264}
1991/05/13
4P6493 Governor Information Plate Available{7557}
1992/06/15
Governor Specifications Are Available Through The Technical Information System{1264,0374}
1992/09/07
Replacement Governors For Early Engines{1264}
1992/11/09
Measuring "Dynamic Rack" Of Unit Injectors{0780}
1993/06/21
New Control Assemblies Used In Fuel Injection Control Groups {1298}
1994/01/17

Caterpillar Parts SIS Catalog 3116 :

DRIVE GP-GOV & TRANSFER PUMP
7E-8794 DRIVE GP-GOV & TRANSFER PUMP
DRIVE GP-GOV & TRANSFER PUMP
6I-0232 DRIVE GP-GOV & TRANSFER PUMP
DRIVE GP-GOV & TRANSFER PUMP
4P-4775 DRIVE GP-GOV & TRANSFER PUMP
DRIVE GP-GOV & TRANSFER PUMP
4P-0666 DRIVE GP-GOV & TRANSFER PUMP
CONTROL GP-GOVERNOR
7E-9429 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
7E-6447 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
7C-7242 CONTROL GP-GOVERNOR
CONTROL GP-GOVERNOR
7C-5203 CONTROL GP-GOVERNOR
FASTENER GP-FUEL INJ PUMP
7W-4812 FASTENER GP-FUEL INJ PUMP
FASTENER GP-FUEL LINES
149-8279 FASTENER GP-FUEL LINES
FASTENER GP-FUEL LINES
149-8865 FASTENER GP-FUEL LINES
FASTENER GP-FUEL LINES
151-5057 FASTENER GP-FUEL LINES
FASTENER GP-FUEL LINES
151-5058 FASTENER GP-FUEL LINES
FASTENER GP-FUEL PUMP
172-4377 FASTENER GP-FUEL PUMP
FASTENER GP-FUEL TRANSFER PUMP
148-6317 FASTENER GP-FUEL TRANSFER PUMP
FILTER & LINES GP-FUEL
112-6698 FILTER & LINES GP-FUEL

Truck sale:

1998 CAT 3116
USD $14,000 
1998 CAT 3116

Milton CAT Power Systems
Milford, Massachusetts
2001 CAT 3116
USD $2,500 
2001 CAT 3116

Foley Equipment Company
Topeka Area, Kansas
 
 
2014 CAT 3116

Yoder & Frey Auctioneers
Ashland, Ohio
1989 CAT 3116
USD $22,500 
1989 CAT 3116

Martin Energy Group LLC
Ephrata, Pennsylvania
1997 CAT 3116
USD $20,997 
1997 CAT 3116

Hewitt Equipment Ltd
QUÉBEC, Quebec, Canada
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.