AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

100-6179 GOVERNOR GP-UNIT INJECTOR S/N 4PG920-UP PART OF 105-4655, 113-4256, 4P-5512, 4P-5670, 4P-5731 GOVERNOR GP-UNIT INJECTOR Type 1 ALSO AN ATTACHMENT 3116


FUEL SYSTEM
GOVERNOR GP

INDUSTRIAL ENGINE 3116 INDUSTRIAL ENGINE 4PG
 3116 Industrial Engine 4PG00001-UP SEBP1789 3116 4PG   (1988)

FUEL SYSTEM

GOVERNOR GP
GOVERNOR GP
7W-5557 GOVERNOR GP
GOVERNOR GP
7W-5557 GOVERNOR GP
GOVERNOR GP-UNIT INJECTOR
100-6179 GOVERNOR GP-UNIT INJECTOR
GOVERNOR GP-UNIT INJECTOR
100-6179 GOVERNOR GP-UNIT INJECTOR
101-3186 GOVERNOR GP-UNIT INJECTOR
101-3187 GOVERNOR GP-UNIT INJECTOR
 

#SEBP17890550
 

100-6179: GOVERNOR GP-UNIT INJECTOR

100-6179 GOVERNOR GP-UNIT INJECTOR
S/N 4PG920-UP
PART OF 105-4655, 113-4256, 4P-5512, 4P-5670, 4P-5731 GOVERNOR GP-UNIT INJECTOR
Type 1
ALSO AN ATTACHMENT
i00461305 SEBP1789
1006179 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8T-1460 [1] RING-RETAINING  
2. 4P-5676 [1] CLEVIS  
3. 4H-1641 [1] PIN-SPRING  
4. 7C-8854 [1] PIN-CLEVIS  
5. 4P-4985 [1] VALVE-GOVERNOR SERVO  
6. 8C-3312 [1] RING-RETAINING  
7. 7W-7364 [1] SLEEVE-GOVERNOR SERVO  
8. 5P-9757 [1] SEAL-O-RING  
9. 7W-7362 [1] PISTON-GOVERNOR SERVO  
10. 4P-4983 [1] SLEEVE  
11. 9Y-1837 [1] SPRING  
12. 8T-7060 [1] RING-RETAINING  
13. 104-7039 [1] SLEEVE-LIMITING  
14. 7N-2171 [1] RING-RETAINING  
15. 7E-3215 [1] LEVER AS  
16. Z [1] PIN  
17. Z [2] SWIVEL  
18. Z [1] LEVER  
19. 7W-5594 [1] SHAFT AS-PIVOT  
20. Z [1] PIN  
21. 7C-5480 [1] SPRING-TORSION  
22. 7C-8640 [1] SPRING-CAM  
23. 7C-6592 [1] ARBOR AS-TORQUE CAM  
24. 8C-6775 M [1] SETSCREW-SOCKET  
25. 7E-3216 [1] BLOCK AS-BEARING  
26. 6F-5933 [2] BEARING AS-NEEDLE  
27. 7E-3217 [1] LEVER AS  
28. Z [1] SWIVEL  
29. 8C-8546 M [9] BOLT-SOCKET HEAD (M5X0.8X14-MM)  
30. 3P-3547 [1] RING-RETAINING  
31. 4P-5743 [1] LEVER AS-LIMIT  
32. Z [1] PIN  
33. Z [1] LEVER-TORQUE  
34. 7E-0155 [1] SCREEN AS-FUEL  
35. 6V-8189 [1] NUT (5/16-18-THD)  
36. 7W-5614 [1] SEAL-GOVERNOR HOUSING  
37. 3T-0849 M [6] BOLT-SOCKET HEAD (M6X1X25-MM)  
38. 7W-4313 [1] WASHER (5X11X1.5-MM THK)  
39. 6I-4514 [1] HOUSING AS  
40. Z [1] SHAFT  
41. Z [1] PLUG  
42. 8T-6702 M [1] SETSCREW-SOCKET (M5X0.8X20-MM)  
43. 5C-2874 M [2] NUT (M5X0.8-THD)  
44. 7C-6204 [1] PLUG  
45. 7L-3386 [1] SEAL-O-RING  
46. 7C-5884 [1] COVER-OIL SUMP  
47. 6V-5213 M [3] BOLT-SOCKET HEAD (M5X0.8X12-MM)  
48. 4P-3539 [1] LEVER-THROTTLE  
49. 8T-5435 M [1] BOLT (M5X0.8X25-MM)  
50. 101-7676 [1] SETSCREW-HEX HEAD  
51. 7C-4483 [1] SCREEN AS (OIL INLET)  
52. 6V-5100 [1] SEAL-O-RING  
53. 4P-4231 [1] COVER-REAR  
54. Z [1] PLUG  
55. 4P-3537 [1] RING-TOLERANCE  
56. 8T-0269 M [3] BOLT-SOCKET HEAD (M6X1X20-MM)  
57. 7E-8794 Y [1] DRIVE GP-GOV & TRANSFER PUMP  
58. 7C-5150 [1] PIN  
59. 4P-0737 [1] SHAFT-RISER  
60. 7C-5148 [1] CARRIER-FLYWEIGHT  
61. 9X-2547 M [2] SCREW-FLAT HEAD (M5X0.8X30-MM)  
62. 2S-7316 [2] DOWEL  
63. 6V-7699 [4] WASHER-HARD (5.5X13X1.6-MM THK)  
64. 8C-8545 M [4] BOLT-SOCKET HEAD (M5X0.8X20-MM)  
65. 7C-5541 [2] PLATE  
66. 7W-8993 [2] WEIGHT  
67. 8C-5061 [1] RING-RETAINING  
68. 7C-2743 [2] RACE  
69. 7W-5561 [1] BEARING-THRUST  
70. 7W-1440 B [8] SHIM (0.12-MM THK)  
71. 4P-8947 [1] RISER  
72. 4P-8948 [1] SEAT AS-SPRING  
73. [1] INSERT  
74. 7C-3776 [1] PISTON AS  
75. 4N-6407 [1] SPOOL-DASHPOT  
76. 4N-6406 [1] RING-SPACER  
77. 4N-6404 [1] RING-RETAINING  
78. 7W-5591 [1] SEAT-GOVERNOR SPRING  
79. 7C-5883 B [7] SHIM (0.25-MM THK)  
80. 7C-5885 [1] WASHER (24.5X41X3-MM THK)  
81. 4P-4000 [1] SPRING-LEVER  
82. 7C-6205 [1] PLUG  
  B   USE AS REQUIRED
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
  Z   NOT SERVICED SEPARATELY
 

#SEBP17890551
 

100-6179: GOVERNOR GP-UNIT INJECTOR

100-6179 GOVERNOR GP-UNIT INJECTOR
S/N 4PG920-UP
PART OF 4P-5724 GOVERNOR GP, 111-1750, 113-4196, 113-4256, 4P-5512, 4P-5670, 4P-5731, 4P-5732, 4P-5733 GOVERNOR GP-UNIT INJECTOR
Type 2
ALSO AN ATTACHMENT
i00461326 SEBP1789
1006179 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8T-1460 [1] RING-RETAINING  
2. 108-1612 [1] CLEVIS  
3. 6D-9953 [1] PIN-SPRING  
4. 7C-8854 [1] PIN-CLEVIS  
5. 115-2553 [1] VALVE-GOVERNOR SERVO  
6. 8C-3312 [1] RING-RETAINING  
7. 7W-7364 [1] SLEEVE-GOVERNOR SERVO  
8. 5P-9757 [1] SEAL-O-RING  
9. 108-1613 [1] PISTON-SERVO  
10. 125-8158 [1] SLEEVE-RACK CONTROL  
11. 9Y-1837 [1] SPRING  
12. 8T-7060 [1] RING-RETAINING  
13. 117-9098 [1] SLEEVE-LIMITING  
14. 7N-2171 [1] RING-RETAINING  
15. 114-1803 C [1] LEVER AS  
16. Z [1] PIN  
17. Z [2] SWIVEL  
18. Z [1] LEVER  
19. 7W-5594 [1] SHAFT AS-PIVOT  
20. Z [1] PIN  
21. 7C-5480 [1] SPRING-TORSION  
22. 7C-8640 [1] SPRING-CAM  
23. 123-6433 [1] ARBOR AS-TORQUE CAM  
24. 8T-8895 M [1] SETSCREW-SOCKET (M4X0.7X16-MM)  
25. 7E-3216 [1] BLOCK AS-BEARING  
26. 6F-5933 [2] BEARING AS-NEEDLE  
27. 7E-3217 [1] LEVER AS  
28. Z [1] SWIVEL  
29. 8C-8546 M [9] BOLT-SOCKET HEAD (M5X0.8X14-MM)  
30. 3P-3547 [1] RING-RETAINING  
31. 4P-5743 [1] LEVER AS-LIMIT  
32. Z [1] PIN  
33. Z [1] LEVER-TORQUE  
34. 7C-6205 [1] PLUG  
35. 6V-8189 [1] NUT (5/16-18-THD)  
36. 115-1192 [1] SEAL-GOVERNOR HOUSING  
37. 3T-0849 M [6] BOLT-SOCKET HEAD (M6X1X25-MM)  
38. 7W-4313 [1] WASHER (5X11X1.5-MM THK)  
39. 6I-4514 [1] HOUSING AS  
40. Z [1] SHAFT  
41. Z [1] PLUG  
42. 8T-6702 M [1] SETSCREW-SOCKET (M5X0.8X20-MM)  
43. 5C-2874 M [2] NUT (M5X0.8-THD)  
44. 7C-6204 [1] PLUG  
45. 7L-3386 [1] SEAL-O-RING  
46. 7C-5884 [1] COVER-OIL SUMP  
47. 6V-5213 M [3] BOLT-SOCKET HEAD (M5X0.8X12-MM)  
48. 4P-3539 [1] LEVER-THROTTLE  
49. 8T-5435 M [1] BOLT (M5X0.8X25-MM)  
50. 1N-3887 C [1] SETSCREW-SOCKET (5/16-18X1.5-IN)  
51. 7C-4483 [1] SCREEN AS (OIL INLET)  
52. 6V-5100 [1] SEAL-O-RING  
53. 4P-4231 [1] COVER-REAR  
54. Z [1] PLUG  
55. 4P-3537 [1] RING-TOLERANCE  
56. 8T-0269 M [3] BOLT-SOCKET HEAD (M6X1X20-MM)  
57. 7E-8794 Y [1] DRIVE GP-GOV & TRANSFER PUMP  
58. 7C-5150 [1] PIN  
59. 4P-0737 [1] SHAFT-RISER  
60. 7C-5148 [1] CARRIER-FLYWEIGHT  
61. 9X-2547 M [2] SCREW-FLAT HEAD (M5X0.8X30-MM)  
62. 2S-7316 [2] DOWEL  
63. 6V-7699 [4] WASHER-HARD (5.5X13X1.6-MM THK)  
64. 8C-8545 M [4] BOLT-SOCKET HEAD (M5X0.8X20-MM)  
65. 7C-5541 [2] PLATE  
66. 7W-8993 [2] WEIGHT  
67. 8C-5061 [1] RING-RETAINING  
68. 7C-2743 [2] RACE  
69. 7W-5561 [1] BEARING-THRUST  
70. 7W-1440 B [8] SHIM (0.12-MM THK)  
71. 4P-8947 [1] RISER  
72. 4P-8948 [1] SEAT AS-SPRING  
73. [1] INSERT  
74. 7C-3776 [1] PISTON AS  
75. 4N-6407 [1] SPOOL-DASHPOT  
76. 4N-6406 [1] RING-SPACER  
77. 4N-6404 [1] RING-RETAINING  
78. 7W-5591 [1] SEAT-GOVERNOR SPRING  
79. 7C-5883 B [7] SHIM (0.25-MM THK)  
80. 7C-5885 [1] WASHER (24.5X41X3-MM THK)  
81. 4P-4000 [1] SPRING-LEVER  
  B   USE AS REQUIRED
  C   CHANGE FROM PREVIOUS TYPE
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
  Z   NOT SERVICED SEPARATELY
 

#SEBP17890552
 

101-3186: GOVERNOR GP-UNIT INJECTOR

101-3186 GOVERNOR GP-UNIT INJECTOR
S/N 4PG1062-UP
i00463127 SEBP1789
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
  7W-4812 Y [1] FASTENER GP-FUEL INJ PUMP  
  101-7356 Y [1] GOVERNOR GP  
    S/N 4PG1062-1711
  110-2322 Y [1] GOVERNOR GP-UNIT INJECTOR  
    S/N 4PG1712-UP
  7W-8434 Y [1] LINES GP-GOVERNOR OIL  
  Y   SEPARATE ILLUSTRATION
 

#SEBP17890553
 

101-3187: GOVERNOR GP-UNIT INJECTOR

101-3187 GOVERNOR GP-UNIT INJECTOR
S/N 4PG2243-UP
i00794252 SEBP1789
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
  7W-4812 Y [1] FASTENER GP-FUEL INJ PUMP  
  110-2320 Y [1] GOVERNOR GP-UNIT INJECTOR  
  7W-8434 Y [1] LINES GP-GOVERNOR OIL  
  Y   SEPARATE ILLUSTRATION
 

#SEBP17890554
 

105-4655: GOVERNOR GP-UNIT INJECTOR

105-4655 GOVERNOR GP-UNIT INJECTOR
FOR USE WITH 2200 RPM & UP APPLICATIONS TO REDUCED RATED ENGINE SPEED TO 2200 RPM
AN ATTACHMENT
i00480714 SEBP1789
1054655 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 100-6179 Y [1] GOVERNOR GP-UNIT INJECTOR  
2. 4P-1698 [1] CAM-TORQUE  
3. 4P-2467 [1] SPRING GP-GOVERNOR  
  [1] SPRING-LOW IDLE  
  [1] SPRING  
4. 7C-4466 [1] SPRING-DASHPOT  
5. 7C-0989 [1] PLUG-ORIFICE  
  Y   SEPARATE ILLUSTRATION
 

#SEBP17890555
 

110-2320: GOVERNOR GP-UNIT INJECTOR

110-2320 GOVERNOR GP-UNIT INJECTOR
S/N 4PG2243-UP
PART OF 101-3187 GOVERNOR GP-UNIT INJECTOR
i00966572 SEBP1789
1102320 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6I-4267 Y [1] GOVERNOR GP-UNIT INJECTOR  
2. 4P-4916 [1] CAM-TORQUE  
3. 4P-4359 [1] SPRING GP-GOVERNOR  
4. 7C-4466 [1] SPRING-DASHPOT  
5. 7C-0989 [1] PLUG-ORIFICE  
6. 4P-5746 [1] CONTROL AS-FUEL RATIO  
7. 4P-5605 B [1] SHIM (0.5-MM THK)  
8. 7E-0155 [1] SCREEN AS-FUEL  
  B   USE AS REQUIRED
  Y   SEPARATE ILLUSTRATION
 

#SEBP17890556
 

110-2321: GOVERNOR GP-UNIT INJECTOR

110-2321 GOVERNOR GP-UNIT INJECTOR
AN ATTACHMENT
i01352903 SEBP1789
1102321 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 130-7323 CY [1] GOVERNOR GP-UNIT INJECTOR  
2. 4P-1441 [1] CAM-TORQUE  
3. 4P-4359 [1] SPRING GP-GOVERNOR  
4. 7C-4466 [1] SPRING-DASHPOT  
5. 7C-0989 [1] PLUG-ORIFICE  
6. 4P-5746 [1] CONTROL AS-FUEL RATIO  
7. 7E-0155 [1] SCREEN AS-FUEL  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

#SEBP17890557
 

110-2322: GOVERNOR GP-UNIT INJECTOR

110-2322 GOVERNOR GP-UNIT INJECTOR
S/N 4PG1712-UP
PART OF 101-3186 GOVERNOR GP-UNIT INJECTOR
Type 1
i00494573 SEBP1789
1102322 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6I-4267 Y [1] GOVERNOR GP-UNIT INJECTOR  
2. 4P-1441 [1] CAM-TORQUE  
3. 7E-3829 [1] SPRING GP-GOVERNOR  
4. 7C-0989 [1] PLUG-ORIFICE  
5. 4P-5746 [1] CONTROL AS-FUEL RATIO  
6. 7C-4466 [1] SPRING-DASHPOT  
7. 4P-5605 [1] SHIM (0.5-MM THK)  
8. 7E-0155 [1] SCREEN AS-FUEL  
  Y   SEPARATE ILLUSTRATION
 

#SEBP17890558
 

110-2322: GOVERNOR GP-UNIT INJECTOR

110-2322 GOVERNOR GP-UNIT INJECTOR
S/N 4PG1712-UP
PART OF 101-3186 GOVERNOR GP-UNIT INJECTOR
Type 2
i00494572 SEBP1789
1102322 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 130-7323 Y [1] GOVERNOR GP-UNIT INJECTOR  
2. 4P-1441 [1] CAM-TORQUE  
3. 7E-3829 [1] SPRING GP-GOVERNOR  
4. 7C-0989 [1] PLUG-ORIFICE  
5. 4P-5746 [1] CONTROL AS-FUEL RATIO  
6. 7C-4466 [1] SPRING-DASHPOT  
7. 4P-5605 [1] SHIM (0.5-MM THK)  
8. 7E-0155 [1] SCREEN AS-FUEL  
  Y   SEPARATE ILLUSTRATION
 

#SEBP17890559
 

110-2323: GOVERNOR GP-UNIT INJECTOR

110-2323 GOVERNOR GP-UNIT INJECTOR
Type 1
AN ATTACHMENT
i00494579 SEBP1789
1102323 GOVERNOR GP-UNIT INJECTOR Parts scheme
  For full view, you need register

Parts for your 3116 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6I-4267 Y [1] GOVERNOR GP-UNIT INJECTOR  
2. 4P-1441 [1] CAM-TORQUE  
3. 4P-4359 [1] SPRING GP-GOVERNOR  
4. 7C-4466 [1] SPRING-DASHPOT  
5. 7C-0989 [1] PLUG-ORIFICE  
6. 4P-5746 [1] CONTROL AS-FUEL RATIO  
7. 7E-0155 [1] SCREEN AS-FUEL  
  Y   SEPARATE ILLUSTRATION
 

Information:

Engine News
Explanation Of Differences In Timing Advance Information
1981/08/26
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Use Correct Calibration Pin (1U9786) When Calibrating Governor; Do Not Use 1U7305 Insertion Tool
1989/11/01
Setscrew And Nut Available For Fuel Setting And Injector Synchronization
1990/11/01
Larger O-ring Seal Available For Oil Supply Port In Governor Housing
1991/05/01
4P6493 Governor Information Plate Available
1992/06/01
Governor Specifications Are Available Through The Technical Information System
1992/09/01
Replacement Governors For Early Engines
1992/10/01
Measuring "Dynamic Rack" Of Unit Injectors
1993/06/01
New Bench Checking And Setting Procedure For Fuel Ratio Control (FRC) Mechanical Goverened Engines{1264,1265}
1996/07/22
New Service Tool Calibration Pins For Mechanical Goverened Engines{1264,1265}
1996/07/22
Governor Shimming Is Determined By The Governor Test Bench Calibration{1264,1289}
1996/07/22
Replacing The Shutoff Assembly In Engines With Older Governors{1264,1289}
1996/07/22
Servo Assembly Parts Have Been Changed To Make Some Parts Common Between Mechanical Governed (Type I-VI) Engines{1264,1289}
1996/07/22
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Operation and Maintenance Manual
Fuel Inlet Screen - Clean/Inspect/Replace
3114, 3116, and 3126 Industrial and Generator Set Engines
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Using the 1U7326 Governor Calibration Bench{1264, 0778}
Using the 1U7326 Governor Calibration Bench{1264, 0778}
Governor Performance Data{1264}
Governor Performance Data{1264}
Using the 127-3458 Sleeve Replacement Tool Group{1290}
Using the 127-3458 Sleeve Replacement Tool Group{1290}
Installing the 4P-9048 Control Assembly or 102-7459 Control Assembly{1298}
Installing the 4P-9048 Control Assembly or 102-7459 Control Assembly{1298}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
Service Letter-NACD
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Vernier Control Cable Assembly
SUPPLEMENT FOR 3114, 3116 & 3126 - INDUSTRIAL ENGINES ENGINES EQUIPPED WIT
Governor Identification - Introduction
3114, 3116 and 3126 MUI Engine Governors
Governor (Type I)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type II)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type IV)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V)
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI)
3114, 3116 and 3126 MUI Engine Governors
Specification
3114, 3116 and 3126 MUI Engine Governors
Governor Performance Data
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII)
3114, 3116 and 3126 MUI Engine Governors
Governor
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines
Service Letter-China
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
Service Letter-Asia
Systems Operation
Governor Speed Circuit
3114, 3116 and 3126 MUI Engine Governors
Governor Limiting Circuit (Types I, II, III, and IV)
3114, 3116 and 3126 MUI Engine Governors
Governor Limiting Circuit (Types V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors
Fuel Ratio Control (Types I and IV)
3114, 3116 and 3126 MUI Engine Governors
Governor Servo (Types I, III, IV, V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors
Dashpot (Types I, III, IV, V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors
Governor Bias Spring (Most Types IV, V, and VI)
3114, 3116 and 3126 MUI Engine Governors
Governor Bumper Spring (Some Type IV)
3114, 3116 and 3126 MUI Engine Governors
Dual Horsepower (Type VI)
3114, 3116 and 3126 MUI Engine Governors
Dual Horsepower (Type VII)
3114, 3116 and 3126 MUI Engine Governors
Torque Limiter Device (Some Type V)
3114, 3116 and 3126 MUI Engine Governors
Information Release Memo
REMANUFACTURED GOVERNORS FOR VARIOUS 3114 AND 3116 INDUSTRIAL, MACHINE, MARINE AND ON-HIGHWAY TRUCK APPLICATIONS
REMANUFACTURED GOVERNORS FOR VARIOUS 3114 AND 3116 INDUSTRIAL, MACHINE, MARINE AND ON-HIGHWAY TRUCK APPLICATIONS
PRODUCT LINE ADDITION: REMAN 3524B HAA ENGINE AVAILABLE FOR 797A & 797B TRUCKS
PRODUCT LINE ADDITION: REMAN 3524B HAA ENGINE AVAILABLE FOR 797A & 797B TRUCKS
Service Letter-APD
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
Testing and Adjusting
Prepare Calibration Bench for Test Procedure
3114, 3116 and 3126 MUI Engine Governors
Installation of Governor on 1U7326 Governor Calibration Bench
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Setting the Governor Load Stop Dimension for More Than 9.00 mm
3114, 3116 and 3126 MUI Engine Governors
Governor (Types I, II, IV, and V) - Check
3114, 3116 and 3126 MUI Engine Governors
Throttle Lever Orientation (Types IV, V, VI, VII, and Some III) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Check
3114, 3116 and 3126 MUI Engine Governors
Governor (Types I, II, and Some III) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Governor (Types IV and Some III) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Adjust
3114, 3116 and 3126 MUI Engine Governors
Throttle Lever (Types IV, V, VI, VII, and Some III) - Remove
3114, 3116 and 3126 MUI Engine Governors
Throttle Lever (Types IV, V, VI, VII, and Some III) - Install
3114, 3116 and 3126 MUI Engine Governors
Governor - Adjust
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines
Troubleshooting
Governor Instability
3114, 3116 and 3126 Engines
Disassembly and Assembly
Governor (Type I) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type I) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type III) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type IV) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type IV) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type V) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VI) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type VII) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type II) - Disassemble
3114, 3116 and 3126 MUI Engine Governors
Governor (Type II) - Assemble
3114, 3116 and 3126 MUI Engine Governors
Governor - Install
3114, 3116 and 3126 Engines
Governor - Remove
3114, 3116 and 3126 Engines
Service Magazine
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Use Correct Calibration Pin (1U9786) When Calibrating Governor; Do Not Use 1U7305 Insertion Tool{0706,0782,1264}
1989/11/06
Some 4C4462 Sleeve Removal And Installation Groups For Unit Injectors May Contain 4C5562 Reamer Assemblies That Are Dimensionally Incorrect {0782,1290}
1990/05/21
Engine Rack Control Assemblies Improved {1257}
1990/07/02
New Fuel Setting Screw Cover And Bolt {1257}
1990/07/02
Setscrew And Nut Available For Fuel Setting And Injector Synchronization {1257}
1990/10/22
Larger O-ring Seal Available For Oil Supply Port In Governor Housing{1264}
1991/05/13
4P6493 Governor Information Plate Available{7557}
1992/06/15
Governor Specifications Are Available Through The Technical Information System{1264,0374}
1992/09/07
Replacement Governors For Early Engines{1264}
1992/11/09
Measuring "Dynamic Rack" Of Unit Injectors{0780}
1993/06/21
New Control Assemblies Used In Fuel Injection Control Groups {1298}
1994/01/17

Caterpillar Parts SIS Catalog 3116 :

GOVERNOR GP
7W-5557 GOVERNOR GP
GOVERNOR GP
7W-5557 GOVERNOR GP
GOVERNOR GP
7W-5557 GOVERNOR GP
7W-5557 GOVERNOR GP
GOVERNOR GP
4P-5724 GOVERNOR GP
GOVERNOR GP
4P-5724 GOVERNOR GP
GOVERNOR GP
4P-5724 GOVERNOR GP
GOVERNOR GP
4P-5724 GOVERNOR GP
GOVERNOR GP-UNIT INJECTOR
100-6179 GOVERNOR GP-UNIT INJECTOR
101-3186 GOVERNOR GP-UNIT INJECTOR
101-3187 GOVERNOR GP-UNIT INJECTOR
GOVERNOR GP-UNIT INJECTOR
105-4655 GOVERNOR GP-UNIT INJECTOR
GOVERNOR GP-UNIT INJECTOR
110-2320 GOVERNOR GP-UNIT INJECTOR
GOVERNOR GP-UNIT INJECTOR
110-2321 GOVERNOR GP-UNIT INJECTOR
GOVERNOR GP-UNIT INJECTOR
110-2322 GOVERNOR GP-UNIT INJECTOR
GOVERNOR GP-UNIT INJECTOR
110-2322 GOVERNOR GP-UNIT INJECTOR

Truck sale:

1998 CAT 3116
USD $14,000 
1998 CAT 3116

Milton CAT Power Systems
Milford, Massachusetts
2001 CAT 3116
USD $2,500 
2001 CAT 3116

Foley Equipment Company
Topeka Area, Kansas
 
 
2014 CAT 3116

Yoder & Frey Auctioneers
Ashland, Ohio
1989 CAT 3116
USD $22,500 
1989 CAT 3116

Martin Energy Group LLC
Ephrata, Pennsylvania
1997 CAT 3116
USD $20,997 
1997 CAT 3116

Hewitt Equipment Ltd
QUÉBEC, Quebec, Canada
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.