ELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINEHARNESS GP
BASIC ENGINE
ENGINE BRAKE GPELECTRICAL AND STARTING SYSTEM
SENSOR GPELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINE#SEBP19130340
7E-2550: CONTROL GP-ENGINE ELECTRONIC
7E-2550 CONTROL GP-ENGINE ELECTRONIC
Type 2
Type 2
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8C-9988 | [1] | CONTROL GP-ELECTRONIC | |
| 2. | 9W-0115 | [6] | MOUNT | |
| 3. | 6V-8189 C | [3] | NUT (5/16-18-THD) | |
| 4. | 7X-1387 | [3] | WASHER (10.26X22.22X1.9-MM THK) | |
| 5. | 8C-9892 | [3] | STUD-MOUNTING | |
| 6. | 8C-9987 | [3] | WASHER (8.3X28X2.5-MM THK) | |
| 7. | 0S-0509 | [1] | BOLT (3/8-16X0.75-IN) | |
| 8. | 5M-2894 | [1] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| C | CHANGE FROM PREVIOUS TYPE | |||
| R | REMANUFACTURED PART MAY BE AVAILABLE | |||
#SEBP19130341
7E-2550: CONTROL GP-ENGINE ELECTRONIC
7E-2550 CONTROL GP-ENGINE ELECTRONIC
Type 1
Type 1
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8C-9988 | [1] | CONTROL GP-ELECTRONIC | |
| 2. | 9W-0115 | [6] | MOUNT | |
| 3. | 1D-4716 | [3] | NUT-FULL (5/16-18-THD) | |
| 4. | 7X-1387 | [3] | WASHER (10.26X22.22X1.9-MM THK) | |
| 5. | 8C-9892 | [3] | STUD-MOUNTING | |
| 6. | 8C-9987 | [3] | WASHER (8.3X28X2.5-MM THK) | |
| 7. | 0S-0509 | [1] | BOLT (3/8-16X0.75-IN) | |
| 8. | 5M-2894 | [1] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| R | REMANUFACTURED PART MAY BE AVAILABLE | |||
#SEBP19130342
7W-1785: CONTROL GP-ENGINE ELECTRONIC
7W-1785 CONTROL GP-ENGINE ELECTRONIC
S/N 5YG1-783
PROGRAMMABLE ELECTRONIC ENGINE CONTROL
S/N 5YG1-783
PROGRAMMABLE ELECTRONIC ENGINE CONTROL
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 5H-9706 | [1] | BOLT | |
| 2. | 2W-3621 | [1] | HOUSING AS | |
| 6F-0984 | [1] | DOWEL | ||
| 2W-0459 | [1] | GASKET | ||
| 3. | 5P-9085 | [1] | CLIP | |
| 4. | 9X-6770 | [1] | SOLENOID-ROTARY | |
| (TIMING ADVANCE) | ||||
| 5. | 9S-8752 | [8] | NUT-FULL (3/8-16-THD) | |
| 5M-2894 | [8] | WASHER-HARD (10.2X18.5X2.5-MM THK) | ||
| 6. | 9W-0497 | [1] | CONTROL GP | |
| (TIMING POSITION SENSOR) | ||||
| 9X-3402 | [4] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8737 | [1] | PLUG-SEAL | ||
| 9W-4059 | [1] | WASHER | ||
| 7. | 3R-6569 | [2] | BOLT (1/4-20X0.875-IN) | |
| 4W-2482 | [2] | CLAMP | ||
| 8. | 2H-3931 | [1] | SEAL-O-RING | |
| 9. | 2W-3623 | [1] | BELLCRANK | |
| 2W-3627 | [1] | SPRING | ||
| 10. | 8N-4524 | [1] | GASKET | |
| 11. | 4B-4909 | [1] | SPRING | |
| 12. | 7E-2898 | [1] | CLIP AS | |
| 13. | 4W-2592 | [1] | COLLAR | |
| 14. | 4W-2480 | [1] | NUT | |
| 15. | 6L-2376 | [1] | BOLT | |
| 16. | 9M-1974 | [2] | WASHER-HARD (8.8X16X2-MM THK) | |
#SEBP19130343
249-5293: HARNESS AS-SENSOR
249-5293 HARNESS AS-SENSOR
PART OF 161-9930 SENSOR GP-PRESSURE
PART OF 161-9930 SENSOR GP-PRESSURE
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 155-2260 | [1] | KIT-CONNECTING PLUG (3-PIN) | ||
| (INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 230-4013 | [1] | PLUG AS-CONNECTOR (3-PIN) | ||
| 264-7030 | [1] | SEAL-CONNECTOR | ||
| 9X-1813 E | SLEEVE (45-CM) | |||
| 194-5226 | [6] | WIRE AS (16-GA) | ||
| -OR- | ||||
| 194-5227 | [6] | WIRE AS (14-GA) | ||
| E | ORDER BY THE CENTIMETER | |||
#SEBP19130344
143-6699: HARNESS AS-WIRING
143-6699 HARNESS AS-WIRING -ENGINE BRAKE
FOR USE WITH JACOBS COMPRESSION BRAKE
FIELD INSTALLATION
FOR USE WITH JACOBS COMPRESSION BRAKE
FIELD INSTALLATION
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| (NO SERVICED PARTS) | ||||
#SEBP19130345
148-7503: HARNESS GP-ENGINE BRAKE
148-7503 HARNESS GP-ENGINE BRAKE
FOR USE WITH COMRESSION BRAKE
FIELD INSTALLATION
FOR USE WITH COMRESSION BRAKE
FIELD INSTALLATION
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS#SEBP19130346
143-4818: KIT-ELECTRONIC CONTROL
143-4818 KIT-ELECTRONIC CONTROL
BOOST AND OIL PRESSURE SENSOR
FIELD INSTALLATION
BOOST AND OIL PRESSURE SENSOR
FIELD INSTALLATION
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS#SEBP19130347
122-1649: KIT-SENSOR & MOUNTING
122-1649 KIT-SENSOR & MOUNTING
OIL PRESSURE
PART OF 143-4818 KIT-ELECTRONIC CONTROL
FIELD INSTALLATION
OIL PRESSURE
PART OF 143-4818 KIT-ELECTRONIC CONTROL
FIELD INSTALLATION
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 161-9930 Y | [1] | SENSOR GP-PRESSURE (ENGINE OIL) | ||
| 5M-3062 | [1] | BOLT (3/8-16X0.75-IN) | ||
| 4P-7581 | [1] | CLIP (LADDER) | ||
| 3E-7448 | [1] | CONNECTOR | ||
| 102-8803 | [2] | KIT-RECEPTACLE (3-PIN) | ||
| (EACH INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [5] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 3J-7354 | [1] | SEAL-O-RING | ||
| 122-1141 | [1] | SENSOR GP-PRESSURE (ENGINE OIL) | ||
| 155-2260 | [1] | KIT-CONNECTING PLUG (3-PIN) | ||
| (INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 180-9340 | [3] | SOCKET-CONNECTOR (14-GA TO 18-GA) | ||
| 9X-1813 E | SLEEVE (34-CM) | |||
| 3S-2093 | [15] | STRAP-CABLE | ||
| 8T-4896 | [1] | WASHER-HARD (10.2X18.5X2.5-MM THK) | ||
| AVAILABLE REPAIR KIT(S): | ||||
| 155-2260 | [1] | KIT-CONNECTING PLUG (3-PIN) | ||
| (INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| E | ORDER BY THE CENTIMETER | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP19130348
247-1804: SENSOR GP
247-1804 SENSOR GP
TRANSDUCER
PART OF 143-4818 KIT-ELECTRONIC CONTROL
FIELD REPLACEMENT FOR @@@@@132-4363@@@@@
TRANSDUCER
PART OF 143-4818 KIT-ELECTRONIC CONTROL
FIELD REPLACEMENT FOR @@@@@132-4363@@@@@
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8T-8734 | [1] | RECEPTACLE-CONNECTOR | |
| 2. | 8T-8731 | [1] | PLUG-CONNECTOR (3-PIN) | |
| 3. | 8T-8735 | [1] | PLUG-CONNECTOR | |
| 4. | 9X-3401 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | |
| 5. | 9X-3402 | [9] | SOCKET-CONNECTOR (16-GA TO 18-GA) | |
| 6. | 9X-1386 E | [76] | SLEEVE (76-CM) | |
| 7. | 3J-7354 | [3] | SEAL-O-RING | |
| 8. | 8T-8737 | [4] | PLUG-SEAL | |
| 9. | 5P-3426 | [1] | ELBOW | |
| 10. | 3J-7352 | [1] | CONNECTOR | |
| 11. | E | TUBE (29-CM) | ||
| 12. | 9S-4182 | [1] | PLUG (7/16-20-THD) | |
| E | ORDER BY THE CENTIMETER | |||
#SEBP19130349
110-8190: SENSOR GP-POSITION
110-8190 SENSOR GP-POSITION
FIELD REPLACEMENT ORDER @@@@@161-8906@@@@@
AN ATTACHMENT
FIELD REPLACEMENT ORDER @@@@@161-8906@@@@@
AN ATTACHMENT
Parts for your 3406B TRUCK ENGINE:
CATERPILLAR SISInformation:
ELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINE
Truck Engine News
Personality Module Software Updated; Do Not Troubleshoot Diagnostic Code 55 (No Detected Faults)
1990/12/01
1990/12/01
A New Version of Caterpillar Electronic Technician (ET) is Now Available {0785, 1900, 7610}
2008/05/01
2008/05/01
Engine News
A New Electronic Control Module Wash Out Process {1901, 1920}
A New Electronic Control Module Wash Out Process {1901, 1920}
A New Electronic Control Module Wash Out Process {1901, 1920}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
Operation and Maintenance Manual
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Using the 8T8697 Electronic Control Analyzer Programmer (ECAP){0781, 0782}
Using the 8T8697 Electronic Control Analyzer Programmer (ECAP){0781, 0782}
Using the 8T8697 Electronic Control Analyzer Programmer (ECAP){0781, 0782}
New Electronic Transducer Module Installation Instructions For 3406B And 3406C Truck Engines{1900, 1904, 1917, 1924}
New Electronic Transducer Module Installation Instructions For 3406B And 3406C Truck Engines{1900, 1904, 1917, 1924}
New Electronic Transducer Module Installation Instructions For 3406B And 3406C Truck Engines{1900, 1904, 1917, 1924}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
Obtaining Factory Passwords and Software Enabled Attachments{7610, 7620}
ECM Communication and Flashing Issues{0709, 1901, 7620}
ECM Communication and Flashing Issues{0709, 1901, 7620}
ECM Communication and Flashing Issues{0709, 1901, 7620}
Instructions for Communicating With and Flashing the <NOBR>10R-4085</NOBR> Engine Electronic Control Gp and the <NOBR>10R-1824</NOBR> Engine Electronic Control Gp {1901, 1920}
Instructions for Communicating With and Flashing the10R-4085 Engine Electronic Control Gp and the 10R-1824 Engine Electronic Control Gp {1901, 1920}
Instructions for Communicating With and Flashing the
Diagnostic Code Information for Caterpillar <SUP>®</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Procedure to Flash the ADEM 3 Engine Electronic Control Gp {1901, 1920}
Procedure to Flash the ADEM 3 Engine Electronic Control Gp {1901, 1920}
Procedure to Flash the ADEM 3 Engine Electronic Control Gp {1901, 1920}
Service Letter-NACD
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
Service Letter-Australia
Service Letter-CFEL
Service Letter-Truck/Ag/Marine
Technical Information Bulletin
Electronic Control Analyzer Programmer (ECAP) Timing Calibration Problem
Electronic Control Analyzer Programmer (ECAP) Timing Calibration Problem
Electronic Control Analyzer Programmer (ECAP) Timing Calibration Problem
Incorrect Programming of the "Pulses Per Mile" Parameter in CAT ET Configuration Screen{0785, 1901}
Incorrect Programming of the "Pulses Per Mile" Parameter in CAT ET Configuration Screen{0785, 1901}
Incorrect Programming of the "Pulses Per Mile" Parameter in CAT ET Configuration Screen{0785, 1901}
Specifications
Tool Operating Manual
Using the ECAP NEXG4512 Customer Parameter Configuration Aid Service Program Module{0781, 0785}
Using the ECAP NEXG4512 Customer Parameter Configuration Aid Service Program Module{0781, 0785}
Using the ECAP NEXG4512 Customer Parameter Configuration Aid Service Program Module{0781, 0785}
Using the ECAP NEXG4521 Machine Functions Service Program Module{0781}
Using the ECAP NEXG4521 Machine Functions Service Program Module{0781}
Using the ECAP NEXG4521 Machine Functions Service Program Module{0781}
Service Letter-China
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
Service Letter-Asia
Information Release Memo
Service Letter-APD
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
The Control Group (Personality Module) Needs To Be Replaced On Certain 460 HP 3406B PEEC Engines
Disassembly and Assembly
Service Magazine
Component Cross Reference Lists For Programed Electronic Engine Control (PEEC) Systems{1900}
1992/04/20
1992/04/20
New Machine Software for Cat<SUP>®</SUP> Product Link Is Now Available on Certain Cat<SUP>®</SUP> Products {7490, 7606, 7610, 7620}
New Machine Software for Cat® Product Link Is Now Available on Certain Cat® Products {7490, 7606, 7610, 7620}
New Machine Software for Cat® Product Link Is Now Available on Certain Cat® Products {7490, 7606, 7610, 7620}




