9Y1932 ENGINE AR-PART 1 OF 2 ENGINE S/N 4TF2472-99999 325 L EXCAVATOR

Part No	Qty	Parts name


6I-1222 Y	[1]	AFTERCOOLER GP
7C-1683 Y	[1]	ALTERNATOR GP

1N-3477 Y	[1]	BREATHER GP

2W-9608 Y	[1]	CAMSHAFT GP-SINGLE
4W-3462 Y	[1]	CARRIER GP-SEAL
7W-6989 Y	[1]	CONTROL GP-FUEL INJECTION
4W-2913 Y	[1]	COOLER GP-ENGINE OIL
4W-2108 Y	[1]	COVER GP-CYLINDER BLOCK
7L-0004 Y	[1]	COVER GP-FRONT
7C-5033 Y	[1]	COVER GP-SOUND SUPPRESSION
9Y-7620 Y	[1]	COVER GP-VALVE MECHANISM
4W-2197 Y	[1]	CRANKSHAFT GP
7E-2482 RY	[1]	CYLINDER BLOCK GP
9Y-8871 Y	[1]	CYLINDER HEAD GP

6I-0772 Y	[1]	DAMPER & PULLEY GP
7C-4532 Y	[1]	DRAIN GP-OIL PAN
7C-0044 Y	[1]	DRIVE GP-FAN
4W-5428 Y	[1]	DRIVE GP-WATER PUMP

9Y-1052 Y	[1]	FILTER GP-ENGINE OIL
6I-2693 Y	[1]	FILTER GP-FUEL
9Y-0283 Y	[1]	FITTING GP
9Y-6092 Y	[1]	FLYWHEEL GP
9Y-3350 Y	[1]	FUMES DISPOSAL GP

4P-0852 Y	[1]	GAUGE GP-OIL LEVEL (DIPSTICK)
2W-8475 Y	[1]	GEAR GP-FRONT
7E-7660 Y	[1]	GOVERNOR GP-UNIT INJECTOR

7W-8813 Y	[1]	HOUSING GP-FLYWHEEL
7L-0002 Y	[1]	HOUSING GP-FRONT

7E-2538 Y	[1]	INSTRUMENT GP
R		REMFG PART MAY BE AVAILABLE
Y		SEPARATE ILLUSTRATION

#SEBP20080002

9Y-1932: ENGINE AR

ENGINE AR

9Y1932 ENGINE AR-PART 2 OF 2
ENGINE S/N 4TF2472-99999

SEBP20080002 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name


4W-2515 Y	[1]	LIFTING GP
7C-6213 Y	[1]	LINES GP-AIR
4P-9693 Y	[1]	LINES GP-AIR FUEL RATIO CONTROL
4W-2914 Y	[1]	LINES GP-ENGINE OIL
4P-9695 Y	[1]	LINES GP-FUEL FILTER
7C-2476 Y	[1]	LINES GP-TURBOCHARGER
6I-3186 Y	[1]	LINES GP-WATER

7C-2472 Y	[1]	MANIFOLD GP-EXHAUST
4W-3480 Y	[1]	MANIFOLD GP-INLET
2W-9607 Y	[1]	MECHANISM GP-FUEL PUMP AND VALVE

4W-0269 Y	[1]	PAN GP-OIL
9Y-8543 Y	[6]	PISTON AND ROD GP
		S/N 4TF2472-5108
100-3694 Y	[6]	PISTON AND ROD GP
		S/N 4TF5109-9999
4W-5429 Y	[1]	PULLEY GP-CRANKSHAFT
4P-7081 Y	[1]	PULLEY GP-FAN DRIVE
4W-2195 Y	[1]	PUMP GP-ENGINE OIL
7E-7607 Y	[6]	PUMP GP-FUEL INJECTION
4P-7206 Y	[1]	PUMP GP-FUEL PRIME AND PRIMARY FILTER
4W-7589 Y	[1]	PUMP GP-WATER

4W-1016 Y	[1]	SEAL GP-CRANKSHAFT
7C-4028 Y	[1]	SOLENOID GP-SHUT-OFF
7C-0747 Y	[1]	STARTING MOTOR GP-ELECTRIC
		S/N 4TF2472-5739

7E-5197 Y	[1]	TURBOCHARGER GP

		GASKET KITS AVAILABLE:

7X-2521		CENTRAL & LOWER STRUCTURE
3E-3278		FRONT STRUCTURE
100-2941		FUEL SYSTEM
7X-2524		OIL COOLER & LINES
7X-2525		REAR STRUCTURE
100-2953		SINGLE CYLINDER HEAD
7X-2526		TURBOCHARGER
7X-2528		WATER PUMP
Y		SEPARATE ILLUSTRATION

#SEBP20080003

7Y-0373: ENGINE AR

ENGINE AR

7Y0373 ENGINE AR
S/N 7TG1-73 & 2JK1-200

SEBP20080003 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name





9Y-1932 Y	[1]	ENGINE AR

4I-7412 Y	[1]	FAN GP-SUCTION

7Y-1534 Y	[1]	MUFFLER GP
Y		SEPARATE ILLUSTRATION

#SEBP20080004

101-3966: ENGINE AR

ENGINE AR

1013966 ENGINE AR
S/N 7TG74-UP & 2JK201-UP

SEBP20080004 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name





101-4871 Y	[1]	ENGINE AR

4I-7412 Y	[1]	FAN GP-SUCTION

7Y-1534 Y	[1]	MUFFLER GP

7C-0747 Y	[1]	STARTING MOTOR GP-ELECTRIC
		- OR -
108-3858 Y	[1]	STARTING MOTOR GP-ELECTRIC
Y		SEPARATE ILLUSTRATION

#SEBP20080005

101-4871: ENGINE AR

ENGINE AR

1014871 ENGINE AR-PART 1 OF 2
ENGINE S/N 98Z2619-UP

SEBP20080005 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name





6I-1222 Y	[1]	AFTERCOOLER GP-TREATED WATER
7C-1683 Y	[1]	ALTERNATOR GP-CHARGING
		S/N 98Z2619-5473
7E-7276 Y	[1]	ALTERCATOR GP-CHARGING
		S/N 98Z5474-UP

1N-3477 Y	[1]	BREATHER GP

2W-9608 Y	[1]	CAMSHAFT GP-SINGLE
4W-3462 Y	[1]	CARRIER GP-SEAL
7W-6989 Y	[1]	CONTROL GP-FUEL INJECTION
		S/N 98Z2619-7746
105-1695 Y	[1]	CONTROL GP-FUEL INJECTION
		S/N 98Z7747-UP
4W-2913 Y	[1]	COOLER GP-ENGINE OIL
		S/N 98Z2619-7746
115-6951 Y	[1]	COOLER GP-ENGINE OIL
		S/N 98Z7747-UP
6I-3766 Y	[1]	COVER GP-CYLINDER BLOCK
7L-0004 Y	[1]	COVER GP-FRONT
7C-5033 Y	[1]	COVER GP-SOUND SUPPRESSION
9Y-7620 Y	[1]	COVER GP-VALVE MECHANISM
4W-2197 Y	[1]	CRANKSHAFT GP
7E-2482 RY	[1]	CYLINDER BLOCK GP
9Y-8871 Y	[1]	CYLINDER HEAD GP
		S/N 98Z2619-7746
4P-8264 Y	[1]	CYLINDER HEAD GP
		S/N 98Z7747-UP

6I-0772 Y	[1]	DAMPER & PULLEY GP
7C-4532 Y	[1]	DRAIN GP-OIL PAN
7C-0044 Y	[1]	DRIVE GP-FAN
4W-5428 Y	[1]	DRIVE GP-WATER PUMP

9Y-1052 Y	[1]	FILTER GP-ENGINE OIL
6I-2693 Y	[1]	FILTER GP-FUEL
9Y-0283 Y	[1]	FITTING GP
9Y-6092 Y	[1]	FLYWHEEL GP
9Y-3350 Y	[1]	FUMES DISPOSAL GP

4P-0852 Y	[1]	GAUGE GP-OIL LEVEL (DIPSTICK)
2W-8475 Y	[1]	GEAR GP-FRONT
7E-7660 Y	[1]	GOVERNOR GP-UNIT INJECTOR

7W-8813 Y	[1]	HOUSING GP-FLYWHEEL
7L-0002 Y	[1]	HOUSING GP-FRONT

7E-2538 Y	[1]	INSTRUMENT GP
R		REMFG PART MAY BE AVAILABLE
Y		SEPARATE ILLUSTRATION

#SEBP20080006

101-4871: ENGINE AR

ENGINE AR

1014871 ENGINE AR-PART 2 OF 2
ENGINE S/N 98Z2619-UP

SEBP20080006 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name




4W-2515 Y	[1]	LIFTING GP
7C-6213 Y	[1]	LINES GP-AIR
4P-9693 Y	[1]	LINES GP-AIR FUEL RATIO CONTROL
4W-2914 Y	[1]	LINES GP-ENGINE OIL
4P-9695 Y	[1]	LINES GP-FUEL FILTER
7C-2476 Y	[1]	LINES GP-TURBOCHARGER
6I-3186 Y	[1]	LINES GP-WATER
7C-2472 Y	[1]	MANIFOLD GP-EXHAUST
6I-2298 Y	[1]	MANIFOLD GP-EXHAUST
		S/N 98Z2619-5473
4W-3480 Y	[1]	MANIFOLD GP-INLET
4P-4372 Y	[1]	MECHANISM GP-FUEL PUMP & VALVE

4W-0269 Y	[1]	PAN GP-OIL
6I-4765 Y	[6]	PISTON & ROD GP
		S/N 98Z2619-5473
107-7546 Y	[6]	PISTON & ROD GP
		S/N 98Z5474-7746
107-7639 Y	[6]	PISTON & ROD GP
		S/N 98Z7747-UP
4W-5429 Y	[1]	PULLEY GP-CRANKSHAFT
4P-7081 Y	[1]	PULLEY GP-FAN DRIVE
4W-2195 Y	[1]	PUMP GP-ENGINE OIL
7E-7607 Y	[6]	PUMP GP-FUEL INJECTION
4P-7206 Y	[1]	PUMP GP-FUEL PRIMING & PRIMARY FILTER
4W-7589 Y	[1]	PUMP GP-WATER

4W-1016 Y	[1]	SEAL GP-CRANKSHAFT
		S/N 98Z2619-7746
115-4203 Y	[1]	SEAL GP-CRANKSHAFT
		S/N 98Z7747-UP
7C-4028 Y	[1]	SOLENOID GP-SHUT-OFF
6I-3765 Y	[1]	SUPPORT GP-CONTROL (GOVERNOR)
		S/N 98Z2619-4998,5012,5013,5015,
		5030-5033,5037,5038,5042,5052-5055,
		5074-5076,5095,5096,5098-5119
116-6688 Y	[1]	SUPPORT GP-CONTROL (GOVERNOR)
		S/N 98Z4999-5011,5014,5016,5029,
		5034-5036,5039-5041,5043-5051
		5056-5073,5077-5094,5097,5120-UP
6I-2267 Y	[1]	TURBOCHARGER GP

		GASKET KITS AVAILABLE

7X-2521		CENTRAL & LOWER STRUCTURE
3E-3278		FRONT STRUCTURE
100-2941		FUEL SYSTEM
7X-2524		OIL COOLER & LINES
7X-2525		REAR STRUCTURE
100-2953		SINGLE CYLINDER HEAD
7X-2526		TURBOCHARGER
7X-2528		WATER PUMP
Y		SEPARATE ILLUSTRATION

#SEBP20080007

7E-2482: CYLINDER BLOCK GP

CYLINDER BLOCK GP

7E2482 CYLINDER BLOCK GP*R
ENGINE S/N 98Z1-13709
7C5826-PAGE 5
FOR USE WITH TWO-PIECE PISTONS

c537301 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7C-5826 Y	[1]	CYLINDER BLOCK GP
2.	6V-3538	[2]	DOWEL
3.	4P-5651	[6]	TUBE AS-PISTON COOLING
4.	7N-5683	[2]	DOWEL
5.	6V-3940 M	[6]	BOLT
6.	1W-8407	[2]	SLEEVE
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP20080008

7E-2482: CYLINDER BLOCK GP

CYLINDER BLOCK GP

7E2482 CYLINDER BLOCK GP*R
ENGINE S/N 98Z13710-17019
1004948-PAGE 4.03
FOR USE WITH TWO-PIECE PISTONS

c607754 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	100-4948 CY	[1]	CYLINDER BLOCK GP
2.	6V-3538	[2]	DOWEL (20MM(.78IN)LG)
3.	4P-5651	[6]	TUBE AS-PISTON COOLING
4.	7N-5683	[2]	DOWEL
5.	6V-3940 M	[6]	BOLT (M8X1.25X25MM)
6.	1W-8407	[2]	SLEEVE
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP20080009

7E-2482: CYLINDER BLOCK GP

CYLINDER BLOCK GP

7E2482 CYLINDER BLOCK GP*R
ENGINE S/N 98Z17020-UP
1291095-PAGE 4.04
FOR USE WITH TWO-PIECE PISTONS

c625371 SEBP2008

For full view, you need register

Parts for your 325 L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	129-1095 YC	[1]	CYLINDER BLOCK GP
2.	6V-3940 M	[6]	BOLT
3.	1W-8407	[2]	SLEEVE
4.	6V-3538	[2]	DOWEL
5.	4P-5651	[6]	TUBE AS-PISTON COOLING
6.	7N-5683	[2]	DOWEL
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

Information:

ENGINE ARRANGEMENT

ENGINE AR

Truck Engine News

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/18

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}

Engine News

Improved Registration Process for Retrofit Products {1000, 7000}
2011/04/15

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/18

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}

Procedure for Cleaning an Engine Lubrication System when Contaminated with Engine Coolant Containing Antifreeze {1000, 1348, 1395}
Procedure for Cleaning an Engine Lubrication System when Contaminated with Engine Coolant Containing Antifreeze {1000, 1348, 1395}

Special Instruction

Troubleshooting Engine Vibration In Vehicular Equipment{1000}
Troubleshooting Engine Vibration In Vehicular Equipment{1000}

Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}

Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}

Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}

Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}

Caterpillar DPF Installation and Operation Guide for Diesel Engines - California Only {1000, 1091}
Caterpillar DPF Installation and Operation Guide for Diesel Engines - California Only {1000, 1091}

Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490}
Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490}

Storage Procedure for Caterpillar Products {0355, 1000, 7000}
Storage Procedure for Caterpillar Products {0355, 1000, 7000}

Recommended Storage Procedures For Hydraulic Excavators {0355, 1000, 1250, 7000}
Recommended Storage Procedures For Hydraulic Excavators {0355, 1000, 1250, 7000}

Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}
Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}

Differences in Appearance of Cat ® Reman Parts when Compared to New Parts {1000, 1250}
Differences in Appearance of Cat ^® Reman Parts when Compared to New Parts {1000, 1250}

Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}

Service Letter-NACD

Product Support Program For Replacing The Travel And Work Mode Solenoid Valves On Certain 325L And 330L Excavators
Product Support Program For Replacing The Travel And Work Mode Solenoid Valves On Certain 325L And 330L Excavators

0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock
0R3002, 0R3003, 0R3190, 0R3389, 0R3580, 0R3742, 0R4368, 0R4369, 0R4370, 0R4374, And 0R4376 Remanufactured Unit Injectors Used On Various 3114 And 3116 Engines Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

A Recommendation for Initial Parts Stock Quantities Will Now Be Included in Service Letters{1000, 7000, 7751, 7752}
A Recommendation for Initial Parts Stock Quantities Will Now Be Included in Service Letters{1000, 7000, 7751, 7752}

Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}

368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}

Specifications

Fine Swing Solenoid Valve Group 4I1042
325, 325L AND 325N EXCAVATOR ATTACHMENTS

Solenoid Valve Group
325, 325L AND 325N EXCAVATOR ATTACHMENTS

Tool Operating Manual

Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}
Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}

Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}
Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}

NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}

142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000}
142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000}

Service Letter-China

Service Letter-Asia

Systems Operation

General Information
3114, 3116, and 3126 Engines

Reuse And Salvage Guidelines

Reuse and Salvage for Mechanical Governor Groups in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI) {0374, 1000, 1050, 1250, 1300}
Reuse and Salvage for Mechanical Governor Groups in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI) {0374, 1000, 1050, 1250, 1300}

Reuse and Testing of Fuel Injection Pump Housing {0374, 1000, 1250, 1300}
Reuse and Testing of Fuel Injection Pump Housing {0374, 1000, 1250, 1300}

HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}
HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}

Cleaning Components with Carbon Dioxide (CO2) {0680, 1000, 7000}
Cleaning Components with Carbon Dioxide (CO₂) {0680, 1000, 7000}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}

Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}

Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}

Contamination Control Guidelines

Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}
Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}

Information Release Memo

CAT REMAN ANNOUNCES ADDITIONAL 3116 AND 3306 ENGINE OPTIONS FOR CAT® MACHINE APPLICATIONS
CAT REMAN ANNOUNCES ADDITIONAL 3116 AND 3306 ENGINE OPTIONS FOR CAT® MACHINE APPLICATIONS

CAT REMAN ANNOUNCES ADDITIONAL C7, C9, C15 AND 3116 ENGINE OPTIONS FOR CAT® MACHINE APPLICATIONS
CAT REMAN ANNOUNCES ADDITIONAL C7, C9, C15 AND 3116 ENGINE OPTIONS FOR CAT® MACHINE APPLICATIONS

CAT REMAN ANNOUNCES ADDITIONAL LONG BLOCK OPTIONS FOR CAT® MACHINE APPLICATIONS (UPDATED COVERAGE CHART)
CAT REMAN ANNOUNCES ADDITIONAL LONG BLOCK OPTIONS FOR CAT® MACHINE APPLICATIONS (UPDATED COVERAGE CHART)

Service Letter-APD

Testing and Adjusting

Engine Speed - Check
3114, 3116, and 3126 Engines

Technical Analysis

Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565}

Disassembly and Assembly

Solenoid Valves
325, 325L & 325N EXCAVATORS VEHICLE SYSTEMS

Engine
SUPPLEMENT FOR 3116 ENGINE 325, 325L, & 325N EXCAVATORS

Service Magazine

Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22

Separate Valve Stem Gauges Available{0653,1000}
1982/06/07

Analyzing A Major Engine Failure{1000}
1982/07/19

Reference Chart for Engine Improvements{0374,1000}
1982/10/25

New Index Lists Engine Special Instructions By SMCS Code{1000,0374}
1986/04/07

Improved 5P3000 Engine And Transmission Shipping Stand Assembly; Modification Available For Stands Already In Use{0640}
1977/04/25

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11

Microfiche For Replacement Engine Bills Of Material {0374,1000}
1987/10/26

Explanation Of Nomenclature Used In Engine Performance{1000,0374}
1978/05/15

Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24

New Solenoid Valve Sealed Against Moisture{5479}
1993/09/27

New Fuel Shutoff Solenoids With Improved Durability Available {1259}
1999/03/22

Solenoid Valve Assembly Is Improved In Pilot Lines Group {5479,5057}
1999/03/29

A New Screen In The TMI System Provides The Status Of Emission Certification Of Engines {1000}
2001/01/08

Caterpillar's Position On The Use Of Biodiesel Fuel In Caterpillar Engines {1000}
2012/09/17

A List Of Contacts For Caterpillar Product Support Is Available {1000, 4450, 7000}
2002/03/25

Responsibilities for Emission Certified Engines {1000}
2005/10/03

Replacement Engines are Available for Legacy Machines {1000}
2010/06/23

Proper Long Term Storage of Caterpillar Products {0355, 1000, 7000}
2009/04/27

Changes To Caterpillar Incident Reporting Field Use Form And DSN Incident Report Entry Screens {1000, 7000}
2013/04/17

Redesigned Fluid Sampling Valves Are Now Available for All Cat Products {7542}
2011/02/11

Improved Registration Process for Retrofit Products {1000, 3000, 7000, 7570}
2011/02/17

TA2 (Technical Analysis) Inspections are Now Available on SIS {0372, 1000, 7000, 753T, 7565}
2013/01/10

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/21

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}

A New Process Is Available to Request Service Animations for Certain Service Information Procedures {1000, 7000}
A New Process Is Available to Request Service Animations for Certain Service Information Procedures {1000, 7000}

Caterpillar Parts SIS Catalog 325 L :

7E-2482 CYLINDER BLOCK GP

Truck sale:

46,000

Caterpillar 325L, Crawler Excavators, Construction
- Crawler Excavators
NMC

36,350

Caterpillar 325L, Crawler Excavators, Construction
- Crawler Excavators
TOROMONT CAT

22,376

Caterpillar 325L, Feller Bunchers, Forestry equipment

FINNING CANADA

75.000

Caterpillar 325 LL, Boomstamladers, Bosbouw
- Knuckleboom loaders
N C MACHINERY CO.

75.000

Caterpillar 325 LL, Raupenbagger, Bau-Und Bergbauausrüstung
- Crawler excavators
N C MACHINERY CO.