OPERATOR STATION
AIR CONDITIONER GPCONTROL GP-HYDRAULIC
CONTROL GP-CLUTCH & BRAKE
OPERATOR STATION
AIR CONDITIONER GP
#SEBP20440340
103-9527: CONDENSER GP-REFRIGERANT
103-9527 CONDENSER GP-REFRIGERANT -WITH FANS
S/N 7PK135-UP
PART OF 104-4517 CONDENSER & MTG GP-REFRIGERANT
Type 1
AN ATTACHMENT
S/N 7PK135-UP
PART OF 104-4517 CONDENSER & MTG GP-REFRIGERANT
Type 1
AN ATTACHMENT
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9X-3451 | [1] | CASE AS | |
| 5C-9553 M | [2] | BOLT (M6X1X16-MM) | ||
| 8T-3490 M | [12] | NUT-WELD (M10X1.5-THD) | ||
| 9G-9151 | [3] | CLIP | ||
| 8T-5413 M | [2] | STUD-WELD (M10X1.5X25-MM) | ||
| 7T-1099 | [6] | LINK | ||
| 8T-3597 M | [12] | NUT-WELD (M12X1.75-THD) | ||
| 8T-3994 M | [2] | STUD-WELD (M6X1-THD) | ||
| 2. | 8T-4137 M | [8] | BOLT (M10X1.5X20-MM) | |
| 3. | 8T-4121 | [8] | WASHER-HARD (11X21X2.5-MM THK) | |
| 4. | 9X-3452 | [2] | GUARD AS-FAN | |
| 5. | 5C-2890 M | [1] | NUT (M6X1-THD) | |
| 6. | 8T-4205 | [1] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 7. | 2L-1224 | [1] | CAP-SEAL (HIGH SIDE) | |
| 8. | 142-8620 | [2] | FAN AS-CONDENSER (4-BLADE) | |
| 9. | 3E-5239 | [1] | RELAY AS (24-VOLT)(CONDENSER BLOWER MOTOR) | |
| 10. | 123-8329 | [1] | HARNESS AS-HEATER & AIR COND | |
| 11. | 6D-4246 | [2] | CLIP (LOOP) | |
| 12. | 106-2721 J | [2] | MOTOR AS (AIR CONDITIONER, HEATER) | |
| (EACH INCLUDES) | ||||
| 3E-3365 | [1] | WEDGE-RECEPTACLE LOCK (2-PIN) | ||
| 9W-0852 | [2] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 13. | 9X-3439 | [1] | COIL-CONDENSER | |
| 14. | 127-9083 | [2] | PLATE | |
| 15. | 8T-4198 M | [4] | BOLT (M10X1.5X100-MM) | |
| 16. | 8T-4133 M | [4] | NUT (M10X1.5-THD) | |
| 17. | 5P-8438 | [1] | GROMMET | |
| 18. | 7T-5868 | [4] | CLAMP AS | |
| 19. | 3S-2093 | [7] | STRAP-CABLE | |
| 20. | 9X-4292 | [4] | TUBE | |
| 21. | 8T-4223 | [12] | WASHER-HARD (13.5X25.5X3-MM THK) | |
| 22. | 2D-2751 | [1] | GROMMET | |
| 23. | 8C-3756 | [1] | FILM-IDENTIFICATION (AIR CONDITIONER) | |
| 24. | 8T-4192 M | [12] | BOLT (M12X1.75X25-MM) | |
| 25. | 5P-1075 | [8] | WASHER-HARD (10.2X22.5X3-MM THK) | |
| 26. | 6V-5749 | [1] | PLUG-BUTTON | |
| 27. | 5P-5673 BD | SEAL | ||
| 28. | 5P-5924 BD | SEAL | ||
| AVAILABLE REPAIR KIT(S): | ||||
| 9G-0398 J | [1] | KIT-MOTOR BRUSH | ||
| (INCLUDES 2 BRUSHES & 2 BRUSH CAPS) | ||||
| B | USE AS REQUIRED | |||
| D | ORDER BY THE METER | |||
| J | REPAIR KIT(S) MARKED J AVAILABLE FOR PART MARKED J | |||
| M | METRIC PART | |||
#SEBP20440341
103-9527: CONDENSER GP-REFRIGERANT
103-9527 CONDENSER GP-REFRIGERANT -WITH FANS
S/N 7PK135-UP
PART OF 104-4517 CONDENSER & MTG GP-REFRIGERANT
Type 2
AN ATTACHMENT
S/N 7PK135-UP
PART OF 104-4517 CONDENSER & MTG GP-REFRIGERANT
Type 2
AN ATTACHMENT
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3E-5239 | [1] | RELAY AS (24-VOLT)(CONDENSER FAN MOTOR) | |
| 2. | 3S-2093 | [7] | STRAP-CABLE | |
| 3. | 7K-1181 C | [2] | STRAP-CABLE | |
| 4. | 7T-5856 | [4] | CLAMP | |
| 5. | 322-4474 | [1] | FILM-INFORMATION (24-VOLT HEATER) | |
| 6. | 344-3037 | [2] | PLUG | |
| 7. | 9X-3452 | [2] | GUARD AS-FAN | |
| 8. | 124-8490 C | [1] | HARNESS AS-HEATER & AIR COND | |
| 8T-8729 | [1] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 9W-0844 | [4] | SOCKET-CONNECTOR (14-GA TO 16-GA) | ||
| 9W-0852 | [2] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 9X-1056 | [4] | TERMINAL-RECEPTACLE (14-GA TO 16-GA) | ||
| 9X-1054 | [1] | PLUG AS-CONNECTOR (4-PIN) | ||
| 102-8803 | [1] | KIT-RECEPTACLE (3-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 155-2270 | [2] | KIT-CONNECTING PLUG (2-PIN) | ||
| (EACH INCLUDES PLUG AS, WEDGE, & INTERFACE SEAL) | ||||
| 9. | 142-8620 | [2] | FAN AS-CONDENSER (4-BLADE) | |
| (EACH INCLUDES) | ||||
| 3H-7180 | [1] | SETSCREW (1/4-28X0.25-IN) | ||
| 10. | 308-6335 | [2] | MOTOR GP-ELECTRIC (CONDENSER FAN) | |
| (EACH INCLUDES) | ||||
| 9W-0852 | [2] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 11. | 203-2070 C | [8] | MOUNT | |
| 12. | 204-9530 C | [4] | TUBE | |
| 13. | 216-0805 C | [1] | KIT-COIL (AIR CONDITIONER) | |
| (INCLUDES COIL, TUBES, MOUNTS, BOLTS & WASHERS) | ||||
| 14. | 204-9532 C | [1] | CASE AS | |
| 7T-1099 | [4] | LINK | ||
| 8T-3490 M | [12] | NUT-WELD (M10X1.5-THD) | ||
| 8T-3597 M | [12] | NUT-WELD (M12X1.75-THD) | ||
| 9G-9151 | [2] | CLIP | ||
| 15. | 4P-8134 C | [2] | CLIP (LADDER) | |
| 16. | 5C-2890 M | [1] | NUT (M6X1-THD) | |
| 17. | 5P-1075 | [8] | WASHER-HARD (10.2X22.5X3-MM THK) | |
| 19. | 7X-0578 | [4] | WASHER-HARD (10.2X32X2.5-MM THK) | |
| 20. | 8T-4121 C | [4] | WASHER-HARD (11X21X2.5-MM THK) | |
| 21. | 8T-4133 M | [4] | NUT (M10X1.5-THD) | |
| 22. | 8T-4137 M | [8] | BOLT (M10X1.5X20-MM) | |
| 23. | 8T-4192 M | [12] | BOLT (M12X1.75X25-MM) | |
| 24. | 8T-4205 | [1] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 25. | 8T-4223 | [12] | WASHER-HARD (13.5X25.5X3-MM THK) | |
| 26. | 8T-6685 CM | [4] | BOLT (M10X1.5X110-MM) | |
| 28. | 5P-5924 D | SEAL (0.1-M EACH) | ||
| 29. | 5P-5672 CD | SEAL (0.6-M EACH) | ||
| 30. | 5P-5908 D | SEAL (0.2-M EACH) | ||
| C | CHANGE FROM PREVIOUS TYPE | |||
| D | ORDER BY THE METER | |||
| M | METRIC PART | |||
#SEBP20440342
103-9527: CONDENSER GP-REFRIGERANT
103-9527 CONDENSER GP-REFRIGERANT -WITH FANS
S/N 7PK135-UP
PART OF 104-4517 CONDENSER & MTG GP-REFRIGERANT
Type 3
AN ATTACHMENT
S/N 7PK135-UP
PART OF 104-4517 CONDENSER & MTG GP-REFRIGERANT
Type 3
AN ATTACHMENT
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3E-5239 | [1] | RELAY AS (24-VOLT)(CONDENSER FAN MOTOR) | |
| 2. | 3S-2093 C | [3] | STRAP-CABLE | |
| 7. | 9X-3452 | [2] | GUARD AS-FAN | |
| 8. | 124-8490 | [1] | HARNESS AS-HEATER & AIR COND | |
| 8T-8729 | [1] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 9W-0844 | [4] | SOCKET-CONNECTOR (14-GA TO 16-GA) | ||
| 9W-0852 | [2] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 9X-1056 | [4] | TERMINAL-RECEPTACLE (14-GA TO 16-GA) | ||
| 9X-1054 | [1] | PLUG AS-CONNECTOR (4-PIN) | ||
| 102-8803 | [1] | KIT-RECEPTACLE (3-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 155-2270 | [2] | KIT-CONNECTING PLUG (2-PIN) | ||
| (EACH INCLUDES PLUG AS, WEDGE, & INTERFACE SEAL) | ||||
| 9. | 399-4829 C | [2] | FAN AS-CONDENSER (5-BLADE) | |
| 11. | 203-2070 | [8] | MOUNT | |
| 12. | 204-9530 | [4] | TUBE | |
| 13. | 216-0805 | [1] | KIT-COIL (AIR CONDITIONER) | |
| (INCLUDES COIL, TUBES, MOUNTS, BOLTS, & WASHERS) | ||||
| 14. | 381-2492 C | [1] | CASE AS | |
| 16. | 5C-2890 CM | [9] | NUT (M6X1-THD) | |
| 17. | 8T-4121 | [8] | WASHER-HARD (11X21X2.5-MM THK) | |
| 19. | 8T-4222 | [4] | WASHER-PLATED (11X32X2.5-MM THK) | |
| 22. | 8T-4137 M | [8] | BOLT (M10X1.5X20-MM) | |
| 23. | 8T-4192 M | [12] | BOLT (M12X1.75X25-MM) | |
| 24. | 9X-8256 C | [9] | WASHER (6.6X12X2-MM THK) | |
| 25. | 8T-4223 | [12] | WASHER-HARD (13.5X25.5X3-MM THK) | |
| 26. | 8T-6685 M | [4] | BOLT (M10X1.5X110-MM) | |
| 28. | 5P-5924 D | SEAL (0.1-M EACH) | ||
| 29. | 5P-5672 D | SEAL (0.6-M EACH) | ||
| 31. | 1P-6522 C | [1] | GROMMET | |
| C | CHANGE FROM PREVIOUS TYPE | |||
| D | ORDER BY THE METER | |||
| M | METRIC PART | |||
#SEBP20440343
8E-8681: CONDENSER GP-REFRIGERANT
8E-8681 CONDENSER GP-REFRIGERANT
S/N 7PK1-UP
PART OF 113-5294, 9U-8270 AIR CONDITIONER AR
AN ATTACHMENT
S/N 7PK1-UP
PART OF 113-5294, 9U-8270 AIR CONDITIONER AR
AN ATTACHMENT
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9N-4219 | [1] | BRACKET AS | |
| 9F-2978 | [2] | NUT-WELD (3/8-16-THD) | ||
| 2. | 5P-1075 | [11] | WASHER-HARD (10.2X22.5X3-MM THK) | |
| 3. | 3S-2093 | [3] | STRAP-CABLE | |
| 4. | 7X-0346 | [2] | BOLT (5/8-11X2-IN) | |
| 8G-5258 | [2] | SPACER (17X35X20-MM THK) | ||
| 5. | 9U-8556 | [1] | GUARD AS | |
| 9F-2978 | [5] | NUT-WELD (3/8-16-THD) | ||
| 1F-0748 | [2] | NUT-WELD (1/2-13-THD) | ||
| 6. | 8P-8540 | [2] | GROMMET | |
| 7. | 8D-0983 | [4] | MOUNTING AS-VIBRATION ISOLATOR | |
| 8. | 7X-0311 | [4] | BOLT (7/16-14X2.25-IN) | |
| 9. | 8T-5360 | [8] | WASHER (12X22.5X2.5-MM THK) | |
| 10. | 9N-4224 | [2] | PLATE | |
| 11. | 8T-4139 M | [4] | BOLT (M12X1.75X30-MM) | |
| 12. | 9X-3450 Y | [1] | CONDENSER GP-REFRIGERANT | |
| 13. | 8D-7185 | [4] | WASHER (11.9X38.1X3-MM THK) | |
| 14. | 6I-9019 | [1] | HARNESS AS | |
| 15. | 3T-3045 | [2] | CLIP AS | |
| 16. | 4D-7794 | [1] | CLIP | |
| 17. | 7X-0447 | [4] | NUT (7/16-14-THD) | |
| 18. | 4K-5122 | [1] | HOLDER AS-FUSE | |
| 7N-2867 | [1] | CAP-FUSE HOLDER | ||
| 8M-0456 | [1] | FUSE (20-AMPERE) | ||
| 19. | 4L-6454 | [13] | BOLT (3/8-16X1-IN) | |
| 20. | 9B-7237 | [8] | BOLT (3/8-16X1.25-IN) | |
| 8M-9124 | [8] | WASHER (10X22.5X8-MM THK) | ||
| 21. | 9U-1934 | [2] | HARNESS AS | |
| 8T-4896 | [2] | WASHER-HARD (10.2X18.5X2.5-MM THK) | ||
| 22. | 6I-9004 | [1] | COVER | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP20440344
9X-3450: CONDENSER GP-REFRIGERANT
9X-3450 CONDENSER GP-REFRIGERANT
S/N 7PK1-134
PART OF 8E-8681 CONDENSER GP-REFRIGERANT
AN ATTACHMENT
S/N 7PK1-134
PART OF 8E-8681 CONDENSER GP-REFRIGERANT
AN ATTACHMENT
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3E-5239 | [1] | RELAY AS (24-VOLT) | |
| 2. | 3S-2093 | [7] | STRAP-CABLE | |
| 3. | 7T-5856 | [4] | CLAMP | |
| 4. | 7X-1076 | [1] | SWITCH AS (HIGH PRESSURE CONDENSER) | |
| 7N-7779 | [1] | SOCKET-CONNECTOR (14-GA TO 18-GA) | ||
| 7N-7780 | [1] | PIN-CONNECTOR (14-GA TO 18-GA) | ||
| 7N-9737 | [1] | HOUSING-RECEPTACLE (14-GA TO 18-GA) | ||
| 5. | 308-6335 | [2] | MOTOR GP-ELECTRIC | |
| (EACH INCLUDES) | ||||
| 9W-0852 | [2] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 6. | 8C-3756 | [1] | FILM-IDENTIFICATION (AIR CONDITIONER) | |
| 7. | 8P-6363 | [1] | PLUG | |
| 8. | 216-0804 | [1] | KIT-REPAIR (CONDENSER COIL) | |
| (INCLUDES WASHER, BOLT, COIL, MOUNT & TUBE) | ||||
| 9. | 204-9532 | [1] | CASE AS | |
| 10. | 9X-3452 | [2] | GUARD AS-FAN | |
| 11. | 204-9530 | [4] | TUBE | |
| 12. | 123-8330 | [1] | HARNESS AS-HEATER & AIR COND | |
| 13. | 7X-0578 | [4] | WASHER-HARD (10.2X32X2.5-MM THK) | |
| 14. | 142-8620 | [2] | FAN AS-CONDENSER (4-BLADE) | |
| (EACH INCLUDES) | ||||
| 3H-7180 | [1] | SETSCREW (1/4-28X0.25-IN) | ||
| 15. | 5C-2890 M | [1] | NUT (M6X1-THD) | |
| 16. | 5P-1075 | [8] | WASHER-HARD (10.2X22.5X3-MM THK) | |
| 17. | 5P-8441 | [1] | GROMMET | |
| 18. | 5P-9085 | [2] | CLIP | |
| 19. | 8T-4121 | [4] | WASHER-HARD (11X21X2.5-MM THK) | |
| 20. | 8T-4133 M | [4] | NUT (M10X1.5-THD) | |
| 21. | 8T-4137 M | [8] | BOLT (M10X1.5X20-MM) | |
| 22. | 8T-4192 M | [12] | BOLT (M12X1.75X25-MM) | |
| 23. | 8T-6685 M | [4] | BOLT (M10X1.5X110-MM) | |
| 24. | 8T-4205 | [1] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 25. | 8T-4223 | [12] | WASHER-HARD (13.5X25.5X3-MM THK) | |
| 26. | 9X-7373 | [1] | GROMMET | |
| 27. | 5P-5672 G | SEAL (0.6-M EACH) | ||
| 28. | 5P-5924 G | SEAL (0.1-M EACH) | ||
| 29. | 5P-5908 G | SEAL (0.2-M EACH) | ||
| 30. | 203-2070 | [8] | MOUNT | |
| G | ORDER BY THE INCH | |||
| M | METRIC PART | |||
#SEBP20440345
8G-4479: CONTROL GP-HYDRAULIC HAND
8G-4479 CONTROL GP-HYDRAULIC HAND
S/N 7PK1-UP
BULLDOZER-LIFT
PART OF 8E-8074 HYDRAULIC AR
S/N 7PK1-UP
BULLDOZER-LIFT
PART OF 8E-8074 HYDRAULIC AR
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 6V-8183 | [2] | NUT-FULL (3/8-24-THD) | |
| 2. | 3W-1486 | [1] | ROD | |
| 3. | 3W-2959 | [1] | COVER | |
| 4. | 7X-0578 | [4] | WASHER-HARD (10.2X32X2.5-MM THK) | |
| 5. | 3W-1488 | [1] | SHAFT AS | |
| 6. | 8G-4650 | [1] | LEVER | |
| 7. | 5P-8167 | [1] | BOLT (3/8-16X0.625-IN) | |
| 8. | 8T-4896 | [5] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| 9. | 3B-4615 | [2] | PIN-COTTER | |
| 10. | 3W-1482 | [1] | SHAFT AS | |
| 11. | 8G-4657 | [1] | YOKE | |
| 12. | 2L-6267 | [1] | LOCKNUT (3/8-24-THD) | |
| 13. | 3W-1484 | [1] | BRACKET AS | |
| 14. | 9B-7237 | [5] | BOLT (3/8-16X1.25-IN) | |
| 15. | 4D-4064 | [1] | ROD END (3/8-24-THD) | |
| 16. | 2K-4973 | [1] | LOCKNUT (3/8-16-THD) | |
| 17. | 6P-5207 | [1] | SEAL-DOMED | |
| 18. | 7M-4914 | [1] | SPRING-HYD DECELERATOR | |
| 19. | 3W-1481 | [1] | ROD (BLADE LIFT) | |
| 20. | 6P-5208 | [1] | GUIDE-CONTROL | |
| 21. | 7X-3374 | [2] | NUT-FULL (1/2-20-THD) | |
| 22. | 9B-7237 | [2] | BOLT (3/8-16X1.25-IN) | |
| 23. | 8T-4896 | [4] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| 24. | 3W-1487 | [1] | SUPPORT | |
| 25. | 8T-0798 | [4] | BEARING-ROLLER | |
| 26. | 8T-0741 | [4] | SEAL-LIP TYPE | |
| 27. | 3W-1473 | [1] | HANDLE | |
| 28. | 5P-8167 | [1] | BOLT (3/8-16X0.625-IN) | |
| 29. | 5J-5315 | [1] | ROD END | |
| 30. | 1B-0676 | [2] | PIN | |
| 31. | 7F-3713 | [1] | ROD-CONTROL |
#SEBP20440346
8G-4480: CONTROL GP-HYDRAULIC HAND
8G-4480 CONTROL GP-HYDRAULIC HAND
S/N 7PK1-UP
BULLDOZER-ANGLING
PART OF 8E-8074 HYDRAULIC AR
S/N 7PK1-UP
BULLDOZER-ANGLING
PART OF 8E-8074 HYDRAULIC AR
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3D-8752 | [1] | LOCKNUT (5/16-24-THD) | |
| 2. | 7S-5757 | [1] | RING-RETAINING | |
| 3. | 5P-8247 C | [1] | WASHER-HARD (17X32X3.5-MM THK) | |
| 4. | 8G-4680 | [1] | YOKE | |
| 5. | 6V-1033 | [1] | END-BEARING ROD | |
| 6. | 9M-1974 | [1] | WASHER-HARD (8.8X16X2-MM THK) | |
| 7. | 3B-4615 | [2] | PIN-COTTER | |
| 8. | 1B-0676 | [2] | PIN | |
| 9. | 7F-3713 | [1] | ROD-CONTROL | |
| 10. | 8E-1370 C | [1] | WASHER-THRUST | |
| 11. | 8T-0798 | [4] | BEARING-ROLLER | |
| 12. | 8T-0741 | [4] | SEAL-LIP TYPE | |
| 13. | 8E-1372 C | [1] | LEVER AS (BLADE ANGLE) | |
| 14. | 7X-3376 C | [2] | NUT-FULL (5/16-24-THD) | |
| 15. | 3W-1496 | [1] | ROD | |
| 16. | 3W-1615 | [1] | LEVER | |
| 17. | 7H-3641 | [1] | END-ROD (5/16-24-THD) | |
| 18. | 6V-8918 C | [1] | BOLT (5/16-18X1.25-IN) | |
| 031-4155 | [1] | LOCKNUT (5/16-18-THD) | ||
| C | CHANGE FROM PREVIOUS TYPE | |||
#SEBP20440347
8G-4481: CONTROL GP-HYDRAULIC HAND
8G-4481 CONTROL GP-HYDRAULIC HAND
S/N 7PK1-UP
BULLDOZER-TILT
PART OF 8E-8074 HYDRAULIC AR
S/N 7PK1-UP
BULLDOZER-TILT
PART OF 8E-8074 HYDRAULIC AR
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7H-3641 | [1] | END-ROD (5/16-24-THD) | |
| 2. | 3W-2960 | [1] | SHAFT AS | |
| 3. | 1B-0676 | [1] | PIN | |
| 4. | 3B-4615 | [1] | PIN-COTTER | |
| 5. | 7F-3713 | [1] | ROD-CONTROL | |
| 6. | 8T-4224 | [2] | WASHER-HARD (8.8X16X2-MM THK) | |
| 7. | 6V-8918 | [2] | BOLT (5/16-18X1.25-IN) | |
| 8. | 031-4155 | [2] | LOCKNUT (5/16-18-THD) | |
| 9. | 8T-4122 | [2] | WASHER-HARD (17X32X3.5-MM THK) | |
| 10. | 9B-7237 | [3] | BOLT (3/8-16X1.25-IN) | |
| 8T-4896 | [3] | WASHER-HARD (10.2X18.5X2.5-MM THK) | ||
| 11. | 8T-0798 | [6] | BEARING-ROLLER | |
| 12. | 8T-0741 | [6] | SEAL-LIP TYPE | |
| 13. | 3W-1493 | [1] | LEVER | |
| 14. | 3W-1495 | [1] | LEVER | |
| 15. | 1B-0676 | [2] | PIN | |
| 3B-4615 | [2] | PIN-COTTER | ||
| 16. | 3R-7116 | [1] | ROD-CONTROL | |
| 17. | 7X-3376 | [4] | NUT-FULL (5/16-24-THD) | |
| 18. | 7H-3641 | [2] | END-ROD (5/16-24-THD) | |
| 19. | 3W-1492 | [1] | LEVER | |
| 1B-8704 | [1] | KEY-WOODRUFF | ||
| 20. | 4L-9337 | [1] | BOLT (3/8-16X1.5-IN) | |
| 6V-8801 | [1] | NUT (3/8-16-THD) | ||
| 21. | 8T-4122 | [3] | WASHER-HARD (17X32X3.5-MM THK) | |
| 22. | 031-4155 | [1] | LOCKNUT (5/16-18-THD) | |
| 6V-8918 | [1] | BOLT (5/16-18X1.25-IN) | ||
| 8T-4224 | [1] | WASHER-HARD (8.8X16X2-MM THK) | ||
| 23. | 8G-4659 | [1] | SHAFT AS (BLADE TILT) | |
| 24. | 3W-1491 | [1] | SUPPORT | |
| 25. | 2H-2292 | [1] | ROD-ADJUSTMENT | |
| 26. | 3B-4617 | [1] | PIN-COTTER (PIN) | |
| 27. | 4J-2701 | [1] | ROD END | |
| 6V-9527 F | [1] | FILM-INSTRUCTION | ||
| F | NOT SHOWN | |||
#SEBP20440348
9N-4828: CONTROL GP-HYDRAULIC HAND
9N-4828 CONTROL GP-HYDRAULIC HAND
S/N 7PK1-UP
GRAPPLE-TILT
PART OF 6I-8949, 9N-4872, 9U-8329 GRAPPLE AR
AN ATTACHMENT
S/N 7PK1-UP
GRAPPLE-TILT
PART OF 6I-8949, 9N-4872, 9U-8329 GRAPPLE AR
AN ATTACHMENT
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7H-3641 | [1] | END-ROD (5/16-24-THD) | |
| 2. | 8T-4122 | [2] | WASHER-HARD (17X32X3.5-MM THK) | |
| 3. | 6V-8918 | [1] | BOLT (5/16-18X1.25-IN) | |
| 031-4155 | [1] | LOCKNUT (5/16-18-THD) | ||
| 4. | 8T-4224 | [1] | WASHER-HARD (8.8X16X2-MM THK) | |
| 5. | 9B-7237 | [3] | BOLT (3/8-16X1.25-IN) | |
| 8T-4896 | [3] | WASHER-HARD (10.2X18.5X2.5-MM THK) | ||
| 6. | 8T-0798 | [6] | BEARING-ROLLER | |
| 7. | 8T-0741 | [6] | SEAL-LIP TYPE | |
| 8. | 3W-2960 | [1] | SHAFT AS | |
| 9. | 3W-1493 | [1] | LEVER (DOZER TILT) | |
| 10. | 3D-8752 | [1] | LOCKNUT (5/16-24-THD) | |
| 11. | 3B-4615 | [1] | PIN-COTTER | |
| 12. | 1B-0676 | [1] | PIN | |
| 13. | 7F-3713 | [1] | ROD-CONTROL | |
| 14. | 3W-1495 | [1] | LEVER (DOZER TILT) | |
| 15. | 1B-0676 | [2] | PIN | |
| 3B-4615 | [2] | PIN-COTTER | ||
| 16. | 8E-0152 | [1] | ROD | |
| 17. | 7X-3376 | [4] | NUT-FULL (5/16-24-THD) | |
| 18. | 6V-1033 | [1] | END-BEARING ROD | |
| 19. | 3W-1492 | [1] | LEVER (DOZER TILT) | |
| 20. | 1B-8704 | [1] | KEY-WOODRUFF | |
| 21. | 6V-8918 | [1] | BOLT (5/16-18X1.25-IN) | |
| 22. | 8T-4224 | [1] | WASHER-HARD (8.8X16X2-MM THK) | |
| 23. | 4L-9337 | [1] | BOLT (3/8-16X1.5-IN) | |
| 6V-8801 | [1] | NUT (3/8-16-THD) | ||
| 24. | 8T-4122 | [3] | WASHER-HARD (17X32X3.5-MM THK) | |
| 25. | 031-4155 | [1] | LOCKNUT (5/16-18-THD) | |
| 26. | 8G-4659 | [1] | SHAFT AS | |
| 27. | 6V-9527 | [1] | FILM-INSTRUCTION | |
| 28. | 3W-1491 | [1] | SUPPORT | |
| 29. | 2H-2292 | [1] | ROD-ADJUSTMENT | |
| 30. | 7H-3641 | [1] | END-ROD (5/16-24-THD) | |
| 31. | 3B-4617 | [1] | PIN-COTTER | |
| 32. | 4J-2701 | [1] | ROD END |
#SEBP20440349
8G-4330: CONTROL GP-STEER CLUTCH & BRK
8G-4330 CONTROL GP-STEER CLUTCH & BRK
S/N 7PK1-UP
PART OF 8E-8072 POWER TRAIN AR
S/N 7PK1-UP
PART OF 8E-8072 POWER TRAIN AR
For full view, you need register
Parts for your D4HTSK III TRACK SKIDDER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8G-5317 | [2] | BUMPER | |
| 6V-8189 | [2] | NUT (5/16-18-THD) | ||
| 2. | 3W-1447 | [1] | LEVER | |
| 3. | 3W-8484 | [1] | LEVER | |
| 4. | 5J-5315 | [4] | ROD END | |
| 5. | 9M-4707 | [1] | ROD | |
| 6. | 3W-8483 | [1] | LEVER | |
| 7. | 5S-7382 | [2] | BOLT (3/8-16X1.375-IN) | |
| 8. | 1B-8706 | [3] | KEY-WOODRUFF | |
| 9. | 3S-2713 | [6] | NUT-FULL (3/8-24-THD) | |
| 10. | 113-8460 | [1] | ROD | |
| 11. | 5P-2566 | [1] | BOLT (1/2-13X1.5-IN) | |
| 12. | 8T-2501 | [1] | BOLT (3/8-16X2-IN) | |
| 2K-4973 | [1] | LOCKNUT (3/8-16-THD) | ||
| 13. | 9M-4461 | [1] | ROD END | |
| 14. | 3W-1446 | [1] | LEVER | |
| 15. | 4L-9337 | [1] | BOLT (3/8-16X1.5-IN) | |
| 16. | 8T-4835 | [1] | BOLT (1/2-13X2-IN) | |
| 17. | 8G-5189 | [1] | SUPPORT | |
| 18. | 1K-4705 | [2] | WASHER | |
| 19. | 1T-0720 | [1] | BOLT-12 POINT HEAD (3/8-16X1.25-IN) | |
| 20. | 8G-5190 | [1] | SHAFT AS | |
| 21. | 8G-5193 | [1] | SHAFT | |
| 22. | 8T-1177 | [2] | BEARING-ROLLER | |
| 23. | 8T-1173 | [2] | SEAL-LIP TYPE | |
| 24. | 8T-1175 | [2] | SEAL-LIP TYPE | |
| 25. | 090-3178 | [2] | BEARING-ROLLER | |
| 26. | 1B-8702 | [2] | KEY-WOODRUFF | |
| 27. | 2Y-5671 | [2] | WASHER (19.43X33X0.91-MM THK) | |
| 28. | 8P-7824 | [2] | KNOB | |
| 29. | 030-7573 | [2] | BOLT (3/8-16X1.5-IN) | |
| 30. | 8P-7826 | [2] | KNOB | |
| 31. | 3W-8485 | [1] | LEVER | |
| 32. | 3W-8486 | [1] | LEVER | |
| 33. | 5S-7379 | [3] | BOLT (3/8-16X0.875-IN) | |
| 34. | 8T-4896 | [12] | WASHER-HARD (10.2X18.5X2.5-MM THK) | |
| 35. | 2L-6267 | [4] | LOCKNUT (3/8-24-THD) | |
| 36. | 1B-0676 | [1] | PIN | |
| 3B-4617 | [1] | PIN-COTTER | ||
| 37. | 3D-9912 | [1] | ROD-CONTROL | |
| 38. | 4D-4064 | [1] | ROD END (3/8-24-THD) | |
| 7X-3174 | [1] | BOLT (3/8-24X1.375-IN) | ||
| 39. | 3W-1448 | [1] | SHAFT | |
| 40. | 8T-1178 | [2] | BEARING-ROLLER | |
| 8T-1174 | [2] | SEAL-LIP TYPE | ||
| 41. | 7X-0291 | [4] | BOLT (3/8-16X3.75-IN) | |
| 42. | 8M-5254 | [6] | SEAL-O-RING | |
| 43. | 1B-8714 | [2] | KEY-WOODRUFF | |
| 44. | 3W-1449 | [1] | SUPPORT | |
| 45. | 9S-1328 | [2] | WASHER (26X41X1.6-MM THK) | |
| 46. | 3T-6498 Y | [1] | VALVE GP-STEERING & BRAKE CONT | |
| 47. | 4L-6454 | [4] | BOLT (3/8-16X1-IN) | |
| 48. | 3W-8487 | [1] | LEVER | |
| Y | SEPARATE ILLUSTRATION | |||
Information:
OPERATOR STATION
AIR CONDITIONER GP
Tool Operating Manual
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Service Magazine
