AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

4P-9524 PUMP GP-FUEL INJECTION S/N 3NL297-UP 3176B INDUSTRIAL ENGINE


FUEL SYSTEM
PUMP GP-FUEL INJECTION
PUMP GP-FUEL PRIMING
PUMP GP-FUEL TRANSFER
SEPARATOR GP-WATER
ELECTRICAL AND STARTING SYSTEM
ALTERNATOR GP-CHARGING

INDUSTRIAL ENGINE 3176B INDUSTRIAL ENGINE 3NL
 3176B Industrial Engine 3NL00001-UP SEBP2226 3176B 3NL   (1993)

FUEL SYSTEM

PUMP GP-FUEL INJECTION
INJECTOR GP-FUEL
153-7923 INJECTOR GP-FUEL
PUMP GP-FUEL INJECTION
100-6448 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
100-6448 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
4P-9524 PUMP GP-FUEL INJECTION
WIRING GP-UNIT INJECTOR
257-4183 WIRING GP-UNIT INJECTOR
WIRING GP-UNIT INJECTOR
4P-9536 WIRING GP-UNIT INJECTOR
 

#SEBP22260280
 

4P-9524: PUMP GP-FUEL INJECTION

4P-9524 PUMP GP-FUEL INJECTION
S/N 3NL297-UP
i00373152 SEBP2226
4P9524 PUMP GP-FUEL INJECTION Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9X-7557 [1] SEAL-O-RING  
2. 152-3001 M [1] BOLT (8X1.25X7-MM)  
3. 9X-7722 [1] SEAL-O-RING  
4. 116-8888 C [1] INJECTOR GP-FUEL  
  6I-2538 [1] CLIP  
5. 7C-8851 [1] CLAMP-INJECTOR  
6. 4P-8525 [1] SPACER (9X16X30-MM THK)  
7. 9X-7317 [1] SEAL-O-RING  
  C   CHANGE FROM PREVIOUS TYPE
  M   METRIC PART
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP22260281
 

7C-2919: PUMP GP-FUEL PRIMING

7C-2919 PUMP GP-FUEL PRIMING
PART OF 103-0707, 103-0708, 105-4237, 111-2701, 4P-9546 LINES GP-FUEL INJECTION
ALSO AN ATTACHMENT
i00404201 SEBP2226
7C2919 PUMP GP-FUEL PRIMING Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 105-2508 [1] PUMP AS-FUEL PRIMING  
4. 6V-5218 M [1] BOLT (M8X1.25X35-MM)  
5. 9M-1974 [1] WASHER-HARD (8.8X16X2-MM THK)  
6. 1P-0436 [1] GASKET (FUEL PRIMING PUMP)  
7. 5P-0537 [1] WASHER-HARD (7.2X14.5X2-MM THK)  
8. 8T-0640 M [1] BOLT (M6X1X30-MM)  
  M   METRIC PART
 

#SEBP22260282
 

4P-9532: PUMP GP-FUEL TRANSFER

4P-9532 PUMP GP-FUEL TRANSFER
i00373165 SEBP2226
4P9532 PUMP GP-FUEL TRANSFER Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 104-7901 C [1] PUMP GP-FUEL TRANSFER  
2. 8C-0624 [1] SEAL-O-RING  
3. 8T-0292 M [2] BOLT (M8X1.25X90-MM)  
4. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
5. 3K-0360 C [1] SEAL-O-RING  
6. 9X-6650 C [1] CONNECTOR-O-RING  
  C   CHANGE FROM PREVIOUS TYPE
  M   METRIC PART
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP22260283
 

2W-4234: SEPARATOR GP-WATER

2W-4234 SEPARATOR GP-WATER
FOR USE WITH MARINE PROPULSION AND MARINE AUXILIARY ENGINES
AN ATTACHMENT
i00359085 SEBP2226
2W4234 SEPARATOR GP-WATER Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2W-4235 [1] BASE AS  
2. 8N-1590 [1] WASHER  
3. 8F-9206 [1] SEAL-O-RING  
4. 8N-1588 [1] BOLT-SEPARATOR  
5. 2W-4273 [1] VALVE AS-VENT (FUEL, WATER SEPARATOR)  
6. 8N-1589 [1] GASKET-SEPARATOR  
7. 2W-4236 [1] CASE AS  
8. 5B-7890 [1] PLUG-PIPE  
9. 8N-1586 [1] SPRING-SEPARATOR  
10. 4B-4281 [1] WASHER (16.8X33X2.5-MM THK)  
11. 8F-4610 [1] RING-RETAINING  
12. 8N-1587 [1] SUPPORT  
13. 8N-1585 [1] SEAL-SEPARATOR  
14. 8N-0205 [1] FILTER ELEMENT-FUEL (WATER SEPARATOR)  
 

#SEBP22260284
 

8N-0940: SEPARATOR GP-WATER

8N-0940 SEPARATOR GP-WATER
S/N 3NL1-7341
PRIMARY 10 MICRON FILTER/WATER SEPARATOR, USE ON SUCTION SIDE OF TRANSFER PUMP WITH 1/2 INCH HOSE
FIELD REPLACEMENT ORDER @@@@@459-3810@@@@@
AN ATTACHMENT
i00428887 SEBP2226
8N0940 SEPARATOR GP-WATER Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8N-0497 [1] BASE AS (FUEL, WATER SEPARATOR)  
2. 8N-1590 [1] WASHER  
3. 8F-9206 [1] SEAL-O-RING  
4. 8N-1588 [1] BOLT-SEPARATOR  
5. 6D-0238 [1] VALVE AS  
6. 8N-1589 [1] GASKET-SEPARATOR  
7. 7N-7368 [1] CASE AS  
8. 6V-0682 [1] VALVE-DRAIN  
9. 8N-1586 [1] SPRING-SEPARATOR  
10. 4B-4281 [1] WASHER (16.8X33X2.5-MM THK)  
11. 8F-4610 [1] RING-RETAINING  
12. 8N-1587 [1] SUPPORT  
13. 8N-1585 [1] SEAL-SEPARATOR  
14. 8N-0205 [1] FILTER ELEMENT-FUEL (WATER SEPARATOR)(PRIMARY)  
 

#SEBP22260285
 

100-5045: ALTERNATOR GP-CHARGING

100-5045 ALTERNATOR GP-CHARGING
24 VOLT, 50 AMPERE
PART OF 100-5047 ALTERNATOR GP-CHARGING
AN ATTACHMENT
i00093506 SEBP2226
1005045 ALTERNATOR GP-CHARGING Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7T-2793 [1] FAN AS (12-BLADE)  
2. 7T-2790 [1] ROTOR AS  
3. 7T-6418 [1] STATOR AS  
4. 7T-2792 [1] FRAME AS  
5. 7T-6417 [1] COIL AS  
6. 7T-2798 [1] REGULATOR AS-VOLTAGE (24-VOLT)(ALTERNATOR)  
7. 7T-2797 [1] COVER  
8. 7T-6416 [1] HOLDER AS-BRUSH (ALTERNATOR)  
9. 7T-2795 [1] FRAME AS  
10. 2K-4821 [1] LOCKNUT (5/8-18-THD)  
11. 5P-8247 [1] WASHER-HARD (17X32X3.5-MM THK)  
12. 7T-2801 [1] CONDENSER  
13. 7X-0447 [1] NUT (7/16-14-THD)  
14. 2H-3920 [1] LOCKWASHER  
15. 9L-6770 [1] CAP-DUST  
16. 6V-8185 [1] NUT (1/4-20-THD)  
17. 1H-3244 [1] LOCKWASHER  
18. 7T-2802 [1] WIRE AS  
   
  1B-8705 F [1] KEY-WOODRUFF  
   
    AVAILABLE REPAIR KIT(S):
  7T-2799 [1] KIT-BEARING  
    (INCLUDES BEARINGS)
  7T-2800 [1] KIT-TERMINAL (ALTERNATOR AIR)  
    (INCLUDES INSULATORS, LOCKWASHERS, WASHERS & NUTS)
  7T-2803 [1] KIT-HARDWARE (ALTERNATOR AIR)  
    (INCLUDES SCREW ASSEMBLIES & BOLT ASSEMBLIES)
  7T-2804 [1] KIT-ALTERNATOR TERMINAL (RELAY)  
    (INCLUDES CAP, BOLT, WIRE AS & BUSHING)
  7T-2805 [1] KIT-ALTERNATOR TERMINAL (NEGATIVE)  
    (INCLUDES NUTS, LOCKWASHERS, WASHER & INSULATORS)
  7T-2816 [1] KIT-HARDWARE (ALTERNATOR AIR)  
    (INCLUDES WASHERS, SPACERS, RING, PLATE AS, BOLT AS & PLATE)
  F   NOT SHOWN
 

#SEBP22260286
 

100-5046: ALTERNATOR GP-CHARGING

100-5046 ALTERNATOR GP-CHARGING
24-VOLTS, 50-AMPERE
PART OF 100-5047 ALTERNATOR GP-CHARGING
AN ATTACHMENT
i00093507 SEBP2226
1005046 ALTERNATOR GP-CHARGING Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9G-7566 [1] FRAME-DRIVE END  
2. 2K-4821 [1] LOCKNUT (5/8-18-THD)  
3. 5P-8247 [1] WASHER-HARD (17X32X3.5-MM THK)  
4. 1B-8705 [1] KEY-WOODRUFF  
5. 9G-7549 [1] SPACER (25X40X9.5-MM THK)  
6. 9G-7551 [1] BEARING  
7. 9G-7564 [1] FAN  
8. 9G-7548 [1] RING  
9. 3T-1886 [1] STATOR AS  
10. 3T-1885 [1] COIL AS-FIELD  
11. 9G-7560 [1] ROTOR AS  
12. 3T-1887 [1] DIODE AS  
13. 9G-7568 [1] FRAME AS-REAR  
14. 9G-7562 [1] COVER AS  
15. 9G-7553 [1] RING-COVER  
16. 9G-7552 [1] BEARING  
17. 9L-6770 [1] CAP-DUST  
18. 9G-7567 [1] REGULATOR AS-VOLTAGE (24-VOLT)(ALTERNATOR)  
19. 7X-0447 [1] NUT (7/16-14-THD)  
20. 5C-2874 M [1] NUT (M5X0.8-THD)  
21. 7X-0620 [1] WASHER-HARD (5.5X13X1.6-MM THK)  
22. 9X-6001 M [4] BOLT (M5X0.8X150-MM)  
23. 8T-0328 [4] WASHER-HARD (5.5X10X1-MM THK)  
24. 8T-5360 [1] WASHER (12X22.5X2.5-MM THK)  
   
    AVAILABLE REPAIR KIT(S):
  9G-7554 [1] KIT-TERMINAL GROUND (ALTERNATOR AIR)  
    (INCLUDES LOCK WASHERS & HEX NUTS)
  9G-7555 [1] KIT-OUTPUT TERMINAL (ALTERNATOR AIR)  
    (INCLUDES BUSHINGS, LOCK WASHERS & HEX NUTS)
  9G-7556 [1] KIT-CAPACITOR (ALTERNATOR AIR)  
    (INCLUDES CAPACITOR, LOCK WASHER & SCREWS)
  9G-7559 [1] KIT-RELAY TERMINAL (ALTERNATOR AIR)  
    (INCLUDES TUBE, NUT, TERMINAL, WASHERS, BUSHING & CAP)
  9G-7565 [1] KIT-REGULATOR TERMINAL (ALTERNATOR AIR)  
    (INCLUDES WASHERS, BUSHING & HEX NUT)
  M   METRIC PART
 

#SEBP22260287
 

100-5047: ALTERNATOR GP-CHARGING

100-5047 ALTERNATOR GP-CHARGING
24-VOLT, 50-AMPERE
FIELD REPLACEMENT FOR @@@@@100-5045@@@@@, @@@@@100-5046@@@@@
AN ATTACHMENT
i00093508 SEBP2226
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
  100-5045 Y [1] ALTERNATOR GP-CHARGING  
    -OR-
  100-5046 Y [1] ALTERNATOR GP-CHARGING  
  R   REMANUFACTURED PART MAY BE AVAILABLE
  Y   SEPARATE ILLUSTRATION
 

#SEBP22260288
 

197-8820: ALTERNATOR GP-CHARGING

197-8820 ALTERNATOR GP-CHARGING
24-VOLT, 95-AMPERE
FIELD REPLACEMENT FOR @@@@@ 9X-7803@@@@@
FIELD INSTALLATION
i01691128 SEBP2226
1978820 ALTERNATOR GP-CHARGING Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 185-2653 [1] FRAME  
2. 5S-7349 [1] BOLT (1/4-20X0.5-IN)  
3. 185-2639 [1] FAN AS  
4. 1H-3244 [1] LOCKWASHER  
5. 185-2645 [1] FRAME  
6. 2K-4821 [1] LOCKNUT (5/8-18-THD)  
7. 5P-8247 [1] WASHER-HARD (17X32X3.5-MM THK)  
8. 228-9657 [1] COVER AS  
9. 8T-4205 [1] WASHER-HARD (7.2X14.5X2-MM THK)  
10. 185-2647 [1] GROMMET  
11. 9L-6770 [1] CAP-DUST  
12. 205-0626 [1] STATOR AS-ALTERNATOR  
13. 185-2638 [2] COLLAR  
14. 185-2654 [1] PLATE  
15. 185-2650 [1] ROTOR AS  
16. 185-2644 [1] COIL AS  
17. 185-2648 [1] REGULATOR AS-VOLTAGE (24-VOLT)(ALTERNATOR)  
18. 6V-8189 [1] NUT (5/16-18-THD)  
19. 8T-4224 [1] WASHER-HARD (8.8X16X2-MM THK)  
20. 3F-9556 [1] LOCKWASHER  
21. 185-2655 [1] KIT-BEARING (ALTERNATOR)  
    (INCLUDES BEARINGS)
22. 199-8436 [1] KIT-TERMINAL (ALTERNATOR AIR)  
    (INCLUDES HOLDER AS, PLATE, INSULATOR, PIN, BOLTS, GROMMET & NUTS)
23. 199-7891 [1] KIT-TERMINAL (ALTERNATOR AIR)  
    (INCLUDES INSULATORS, WASHERS & NUTS)
24. 185-2658 [1] KIT-HARDWARE (ALTERNATOR AIR)  
    (INCLUDES BOLTS)
 

#SEBP22260289
 

266-7227: ALTERNATOR GP-CHARGING

266-7227 ALTERNATOR GP-CHARGING
24-VOLT, 60-AMPERE
FIELD REPLACEMENT FOR @@@@@ 4N-3986@@@@@
i02788059 SEBP2226
2667227 ALTERNATOR GP-CHARGING Parts scheme
  For full view, you need register

Parts for your 3176B INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8T-4205 [1] WASHER-HARD (7.2X14.5X2-MM THK)  
2. 1H-3244 [1] LOCKWASHER  
3. 6V-8187 [1] NUT (1/4-28-THD)  
4. 292-3815 [2] KIT-TERMINAL  
5. 9L-6770 [1] CAP-DUST  
6. 5P-3418 [1] BEARING-ROLLER  
7. 5P-3419 [1] RACE-BEARING INNER  
8. 291-8247 [1] RECTIFIER AS  
9. 202-2708 [1] DIODE AS  
10. 3T-6354 [1] REGULATOR AS-VOLTAGE (24-VOLT)(ALTERNATOR)  
11. 291-8253 [1] CAPACITOR AS  
12. 202-9897 [1] BEARING-SPECIAL BALL  
13. 100-6531 [1] FAN-ALTERNATOR (11-BLADE)  
14. 187-2034 [1] NUT-FLANGE (5/8-18-THD)  
15. 291-8274 [1] PLATE  
16. 291-8271 [1] HOUSING AS  
17. 202-2700 [1] FRAME  
18. 291-8263 [1] STATOR AS  
19. 6N-1945 [1] COIL AS-FIELD  
20. 9S-2390 [1] RETAINER  
21. 9S-2302 [1] ROTOR AS  
22. 4B-2047 [1] NUT (10-24-THD)  
23. 8T-0328 [1] WASHER-HARD (5.5X10X1-MM THK)  
24. 8F-1434 [1] LOCKWASHER  
25. 202-2784 [1] KIT-ALTERNATOR TERMINAL (OUTPUT)  
    (KIT INCLUDES NUT, WASHERS, INSULATORS, CONNECTORS, ADAPTER, & SCREW)
26. 202-2785 [1] KIT-ALTERNATOR TERMINAL (RELAY)  
    (KIT INCLUDES STUD, BUSHINGS, CONNECTOR, & NUT)
27. 202-2786 [1] KIT-ALTERNATOR TERMINAL (INDICATOR LIGHT)  
    (KIT INCLUDES NUTS, WASHERS, BUSHINGS, & CONNECTOR)
   
  202-2787 F [1] KIT-HARDWARE (ALTERNATOR AIR)  
    (KIT INCLUDES NUTS, SCREWS, WASHER, BOOT, COLLAR, & CONNECTOR)
  F   NOT SHOWN
 

Information:

Engine News
Explanation Of Differences In Timing Advance Information
1981/08/26
New Fuel Nozzle Test Sheet Available
1982/10/20
Bulged Capsule-Type Fuel Nozzles
1982/10/20
Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Special Instruction, SEHS9246-01, "Using 9U-6860 Tool Group To Replace Unit Injector Sleeves" Is Available {1713}
1996/09/23
Caterpillar High Efficiency Fuel Filters Help Provide Maximum Fuel Pump And Fuel Injector Life {1261}
1996/09/23
Procedure To Investigate Misfires On Engines Equipped With Electronic Unit Injectors (EUI){1290}
1997/05/01
Stronger Injector Hold Down Bolt Used In Fuel Injection Pump Groups{1290}
1998/04/01
Do NOT Interchange Electrical Stators Between Electronic Unit Injectors (EUIs) {1290}
1998/05/01
Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Torque Increased for Nuts on Fuel Injector Wiring Harness {1290}
2000/01/01
Improved O-Ring Seals for Fuel Injectors for Longer Seal Life {1254}
2003/10/01
Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Operation and Maintenance Manual
Electronic Unit Injector - Inspect/Adjust
3176B Industrial Engine
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Using 9U-6860 Tool Group To Replace Unit Injector Sleeves{1290}
Using 9U-6860 Tool Group To Replace Unit Injector Sleeves{1290}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Service Letter-NACD
Certain Fuel Injectors Need To Be Removed From Part Stock
Certain Fuel Injectors Need To Be Removed From Part Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Fuel Transfer Pump
3176B INDUSTRIAL ENGINE
Electronic Unit Injector Mechanism Group
3176B INDUSTRIAL ENGINE
Unit Injector Rocker Arm Assembly
3176B INDUSTRIAL ENGINE
Electronically Controlled Unit Injector
3176B INDUSTRIAL ENGINE
Valve Mechanism Group
3176B INDUSTRIAL ENGINE
Valve Mechanism Cover Group
3176B INDUSTRIAL ENGINE
Service Letter-China
Certain Fuel Injectors Need To Be Removed From Part Stock
Certain Fuel Injectors Need To Be Removed From Part Stock
Service Letter-Asia
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Service Letter-APD
Certain Fuel Injectors Need To Be Removed From Part Stock
Certain Fuel Injectors Need To Be Removed From Part Stock
Disassembly and Assembly
Fuel Transfer Pump
3176B INDUSTRIAL ENGINE
Rocker Arm Assemblies & Push Rods
3176B INDUSTRIAL ENGINE
EUI (Electronic Unit Injectors)
3176B INDUSTRIAL ENGINE
Service Magazine
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14

Caterpillar Parts SIS Catalog 3176B :

PUMP GP-FUEL INJECTION
100-6448 PUMP GP-FUEL INJECTION
PUMP GP-FUEL INJECTION
100-6448 PUMP GP-FUEL INJECTION
LINES GP-FUEL INJECTION
4P-9546 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
111-2701 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
105-4237 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
105-4237 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
103-0708 LINES GP-FUEL INJECTION
LINES GP-FUEL INJECTION
103-0708 LINES GP-FUEL INJECTION
PUMP GP-FUEL PRIMING
7C-2919 PUMP GP-FUEL PRIMING
PUMP GP-FUEL TRANSFER
4P-9532 PUMP GP-FUEL TRANSFER
SEPARATOR GP-WATER
2W-4234 SEPARATOR GP-WATER
SEPARATOR GP-WATER
8N-0940 SEPARATOR GP-WATER
ALTERNATOR GP-CHARGING
100-5045 ALTERNATOR GP-CHARGING
ALTERNATOR GP-CHARGING
100-5046 ALTERNATOR GP-CHARGING
100-5047 ALTERNATOR GP-CHARGING
ALTERNATOR GP-CHARGING
197-8820 ALTERNATOR GP-CHARGING

Truck sale:

Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.