WORK TOOLS
GROUND ENGAGING TOOLS (G.E.T.)RIPPER GP
GROUND ENGAGING TOOLS (G.E.T.)
SERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMSGASKET & SEAL KITS
WORK TOOLS
GROUND ENGAGING TOOLS (G.E.T.)
#SEBP26360640
506-5922: EDGE-CUTTING
For full view, you need register
Parts for your D6R TRACK-TYPE TRACTOR:
| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| (NO SERVICED PARTS) | ||||
#SEBP26360641
9W-0610: MOUNTING GP-RIPPER
For full view, you need register
Parts for your D6R TRACK-TYPE TRACTOR:
| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9W-0609 | [4] | SPACER (53X100X35-MM THK) | |
| 2. | 1U-0301 | [2] | BRACKET AS | |
| 3. | 1U-0612 | [2] | PIN | |
| 4. | 7X-0292 | [2] | BOLT (3/8-16X4.5-IN) | |
| 2K-4973 | [2] | LOCKNUT (3/8-16-THD) | ||
| 5. | 1K-6872 | [2] | LOCKNUT (1/2-13-THD) | |
| 6. | 5D-3118 | [20] | STUD-TAPERLOCK (1-8-THD) | |
| 7. | 7X-0335 | [2] | BOLT (1/2-13X5.25-IN) | |
| 8. | 1U-0300 | [1] | BRACKET AS (RH) | |
| 7T-1975 | [1] | BRACKET AS (LH) | ||
| 9. | 1U-0159 | [2] | PIN | |
| 10. | 9N-4449 B | [12] | SPACER (68X121X1.5-MM THK) | |
| 11. | 6V-8190 | [20] | NUT (1-8-THD) | |
| 12. | 9N-4450 B | [4] | SPACER (68X120X5-MM THK) | |
| B | USE AS REQUIRED | |||
#SEBP26360642
9W-0804: RIPPER AR
For full view, you need register
Parts for your D6R TRACK-TYPE TRACTOR:
| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 9T-2716 Y | [1] | CYLINDER GP-RIPPER | ||
| 3W-1356 Y | [1] | GUARD GP-TRANSMISSION | ||
| 9W-1018 Y | [1] | LINES GP-RIPPER | ||
| 9W-0610 Y | [1] | MOUNTING GP-RIPPER | ||
| 9W-1017 Y | [1] | RIPPER GP | ||
| 8M-3494 | [1] | PLATE-SERIAL NUMBER (RIPPER) | ||
| ON CARRIAGE ASSEMBLY ON RH SIDE OF RH TOWER | ||||
| 4B-4158 | [2] | SCREW-DRIVE (NO 4X0.25-IN) | ||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP26360643
9W-1017: RIPPER GP
For full view, you need register
Parts for your D6R TRACK-TYPE TRACTOR:
| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9W-0201 | [1] | CARRIAGE AS | |
| 1A. | 5K-7748 | [3] | HOLDER-BIT | |
| 9W-0513 | [2] | PLATE AS | ||
| 2. | 2K-4309 | [1] | REINFORCEMENT (RH) | |
| 2K-4310 | [1] | REINFORCEMENT (LH) | ||
| 3. | 9W-0553 | [1] | PLATE AS | |
| 4. | 9J-9598 | [2] | PIN | |
| 5. | 7X-0292 | [2] | BOLT (3/8-16X4.5-IN) | |
| 2K-4973 | [2] | LOCKNUT (3/8-16-THD) | ||
| 6. | 8T-9389 | [8] | BOLT (1/2-13X2.75-IN) | |
| 7. | 6V-8188 | [8] | NUT (1/2-13-THD) | |
| 8. | 9W-0873 | [2] | LINK AS | |
| (EACH INCLUDES) | ||||
| 9. | 9W-0876 | [2] | BUSHING | |
| 10. | 3B-8489 | [3] | FITTING-GREASE (1/8-27 PTF) | |
| 11. | 4K-3004 | [2] | BEARING-TRUNNION SUPPLEMENTARY | |
| 12. | 3K-8510 | [1] | PIN | |
| 13. | 5C-6565 | [2] | BOLT (1/2-13X1.125-IN) | |
| 14. | 2K-0703 | [1] | BAR | |
| 15. | 189-0985 | [1] | FRAME & BEARING AS | |
| 3B-8489 | [4] | FITTING-GREASE (1/8-27 PTF) | ||
| 16. | 9W-0099 | [4] | BUSHING | |
| 17. | 1U-0159 | [2] | PIN | |
| 18. | 7X-0340 | [2] | BOLT (1/2-13X6.5-IN) | |
| 19. | 9J-8926 Y | [1] | TOOTH GP-RIPPER | |
| 20. | 8T-4223 | [18] | WASHER-HARD (13.5X25.5X3-MM THK) | |
| 21. | 1K-6872 | [2] | LOCKNUT (1/2-13-THD) | |
| Y | SEPARATE ILLUSTRATION | |||
#SEBP26360644
3A-7880: TOOTH GP-RIPPER
For full view, you need register
Parts for your D6R TRACK-TYPE TRACTOR:
| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 8J-2189 Y | [3] | TOOTH GP-RIPPER | ||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP26360645
8J-2189: TOOTH GP-RIPPER
8J-2189 TOOTH GP-RIPPER -STRAIGHT
S/N 4JR1-UP
PART OF 3A-7880 TOOTH GP-RIPPER
Type 1
AN ATTACHMENT
S/N 4JR1-UP
PART OF 3A-7880 TOOTH GP-RIPPER
Type 1
AN ATTACHMENT
For full view, you need register
#SEBP26360646
8J-2189: TOOTH GP-RIPPER
8J-2189 TOOTH GP-RIPPER -STRAIGHT
S/N 4JR1-UP
PART OF 3A-7880 TOOTH GP-RIPPER
Type 2
AN ATTACHMENT
S/N 4JR1-UP
PART OF 3A-7880 TOOTH GP-RIPPER
Type 2
AN ATTACHMENT
For full view, you need register
#SEBP26360647
9J-8926: TOOTH GP-RIPPER
9J-8926 TOOTH GP-RIPPER -CURVED
S/N 3SH1-UP; 4JR1-UP
PART OF 9W-1017 RIPPER GP
AN ATTACHMENT
S/N 3SH1-UP; 4JR1-UP
PART OF 9W-1017 RIPPER GP
AN ATTACHMENT
For full view, you need register
#SEBP26360648
126-2300: FILM GP
For full view, you need register
Parts for your D6R TRACK-TYPE TRACTOR:
| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 107-9250 | [1] | FILM-STRIPE (CAT, RH) | |
| 126-2285 | [1] | FILM-STRIPE (CAT, LH) | ||
| 2. | 126-2281 | [1] | FILM-STRIPE (CATERPILLAR, FRONT) | |
| 3. | 126-2295 | [1] | FILM-STRIPE (D6R, LH) | |
| 4. | 126-2282 | [1] | FILM-STRIPE (RH) | |
| 5. | 126-2299 | [1] | FILM-STRIPE (D6R XL, RH, TANK GUARD) | |
| 6. | 126-2280 | [1] | FILM-STRIPE (CATERPILLAR, REAR) | |
| 7. | 137-3924 | [1] | FILM-STRIPE (LH) | |
| 8. | [1] | FILM-STRIPE (XL, LH) | ||
#SEBP26360649
177-4134: KIT-GASKET
177-4134 KIT-GASKET -TORQUE CONVERTER
S/N 4JR1-UP
KIT INCLUDES ALL SEALS, GASKETS & BENDABLE LOCKS TO OVERHAUL A TORQUE CONVERTER
FOR USE WITH @@@@@ 1T-2004@@@@@
FIELD INSTALLATION
S/N 4JR1-UP
KIT INCLUDES ALL SEALS, GASKETS & BENDABLE LOCKS TO OVERHAUL A TORQUE CONVERTER
FOR USE WITH @@@@@ 1T-2004@@@@@
FIELD INSTALLATION
For full view, you need register
Parts for your D6R TRACK-TYPE TRACTOR:
| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 8H-9818 | [1] | GASKET | ||
| 136-2216 | [1] | SEAL-LIP TYPE | ||
| 1S-9799 | [1] | SEAL-O-RING | ||
| 2S-2251 | [1] | SEAL-O-RING | ||
| 6F-4718 | [1] | SEAL-O-RING | ||
| 8M-4433 | [2] | SEAL-O-RING | ||
| 8M-4986 | [1] | SEAL-O-RING | ||
| 8M-8157 | [1] | SEAL-O-RING | ||
| 9H-0846 | [1] | SEAL-O-RING | ||
| FOR A LIST OF RELATED PARTS THAT MAY BE REQUIRED FOR THE ENGINE REBUILD TO THE KIT CONSIST, PLEASE VISIT | ||||
| HTTP://DEALER.CAT.COM/RELATED | ||||
Information:
WORK TOOLS
GROUND ENGAGING TOOLS (G.E.T.)
Special Instruction
Installation and Removal Of The Mechanically Attached Wear Plate System
Installation and Removal Of The Mechanically Attached Wear Plate System
Installation and Removal Of The Mechanically Attached Wear Plate System
256-2930 Recommended K Series Flush Mount/Abrasion Adapter Welding Sequence{0679, 6800, 6801, 6802, 6803, 6805}
256-2930 Recommended K Series Flush Mount/Abrasion Adapter Welding Sequence{0679, 6800, 6801, 6802, 6803, 6805}
256-2930 Recommended K Series Flush Mount/Abrasion Adapter Welding Sequence{0679, 6800, 6801, 6802, 6803, 6805}
Tool Operating Manual
Using the 149-0173 Choker-Style Fabric Basket to Install and Remove Bucket Teeth{0374, 0599, 0751, 6700, 6800}
Using the 149-0173 Choker-Style Fabric Basket to Install and Remove Bucket Teeth{0374, 0599, 0751, 6700, 6800}
Using the 149-0173 Choker-Style Fabric Basket to Install and Remove Bucket Teeth{0374, 0599, 0751, 6700, 6800}
Using 149-0174 Non-Choker Style Fabric Baskets to Install or Remove Bucket or Blade Cutting Edges{0374, 0599, 0632, 0700, 0751, 6800}
Using 149-0174 Non-Choker Style Fabric Baskets to Install or Remove Bucket or Blade Cutting Edges{0374, 0599, 0632, 0700, 0751, 6800}
Using 149-0174 Non-Choker Style Fabric Baskets to Install or Remove Bucket or Blade Cutting Edges{0374, 0599, 0632, 0700, 0751, 6800}
