204-3604 WIRING GP-ELECTRONIC CONTROL S/N 4ZF7985-UP PART OF 234-2917 ENGINE AR Type 2 330C L EXCAVATOR

ELECTRICAL AND STARTING SYSTEM

WIRING GP

0. 204-3604 WIRING GP-
1. 204-3604 WIRING GP-
2. 193-3391 WIRING GP-
3. 163-6640 WIRING GP-

POWER TRAIN

DRIVE GP-FINAL

4. 199-4578 DRIVE GP-F
5. 199-4579 DRIVE GP-F
6. 199-4746 DRIVE GP-F
7. 199-4747 DRIVE GP-F
8. 199-4760 DRIVE GP-F
9. 227-6103 DRIVE GP-F
0. INFORMATION

EXCAVATOR 330C L EXCAVATOR GKX
330C & 330C L Excavators GKX00001-UP (MACHINE) POWERED BY C-9 Engine SEBP3152 330C L GKX (2001)

ELECTRICAL AND STARTING SYSTEM

WIRING GP

204-3604 WIRING GP-ELECTRONIC CONTROL

193-3391 WIRING GP-FINE SWING

163-6640 WIRING GP-REFUELING PUMP

#SEBP31520260

204-3604: WIRING GP-ELECTRONIC CONTROL

WIRING GP-ELECTRONIC CONTROL

204-3604 WIRING GP-ELECTRONIC CONTROL
S/N 4ZF7985-UP
PART OF 234-2917 ENGINE AR
Type 2

i02556247 SEBP3152

2043604 WIRING GP-ELECTRONIC CONTROL Parts scheme

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[24]	STRAP-CABLE
3.	215-3249	[1]	HARNESS AS-ENGINE (UNIT INJECTOR)
	3S-2093	[5]	STRAP-CABLE
	191-7823	[1]	RECEPTACLE AS
			(INCLUDES PLUG AS & WEDGE)
4.	226-0903	[1]	CABLE AS
5.	230-6279	[1]	HARNESS AS-ENGINE (ENGINE ELECTRONIC-LOWER)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	6I-4347	[4]	BOOT (4-PIN)
	100-3320	[1]	PLUG AS-CONNECTOR (2-PIN)
	111-2416	[1]	PLUG AS-CONNECTOR (2-PIN)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
	160-7690	[1]	PLUG AS-CONNECTOR (70-PIN)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	214-7170 L	[1]	KIT-REPAIR (ELECTRICAL CONNECTORS)
			(FOR EXTREME COLD CLIMATES)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	3E-3371	[2]	WEDGE-RECEPTACLE LOCK (3-PIN)
	8T-8737	[8]	PLUG-SEAL
	155-2276	[3]	WEDGE-PLUG LOCK (3-PIN)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	194-5226	[1]	WIRE AS (16-GA)
	194-5227	[1]	WIRE AS (14-GA)
6.	223-4453 CY	[1]	SWITCH GP-MAGNETIC (24-VOLT)(STARTING AID HEATER)
8.	4P-7581	[5]	CLIP (LADDER)
9.	4P-8134	[3]	CLIP (LADDER)
10.	5P-7970 M	[1]	NUT (M8X1.25-THD)
11.	6V-4369	[1]	CLIP
12.	6V-5839 C	[6]	WASHER (11X21X2.5-MM THK)
13.	6V-6317 CM	[2]	BOLT (M10X1.5X20-MM)
14.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
15.	8T-0328	[2]	WASHER-HARD (5.5X10X1-MM THK)
16.	7I-2272 M	[2]	BOLT (M5X0.8X12-MM)
17.	8T-4205	[1]	WASHER-HARD (7.2X14.5X2-MM THK)
18.	8T-5451 M	[1]	BOLT (M6X1X12-MM)
19.	9M-1974	[1]	WASHER-HARD (8.8X16X2-MM THK)
20.	8T-4133 CM	[2]	NUT (M10X1.5-THD)
21.	101-3129 CM	[2]	STUD (M10X1.5-THD)
	C		CHANGE FROM PREVIOUS TYPE
	L		KIT MARKED "L" PROVIDES OIL GRADE PLUGS FOR 0W20, 10W30, 15W40 OIL GRADES
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP31520261

204-3604: WIRING GP-ELECTRONIC CONTROL

WIRING GP-ELECTRONIC CONTROL

204-3604 WIRING GP-ELECTRONIC CONTROL
S/N 4ZF7985-UP; 7AZ103-UP
PART OF 208-3027, 234-2917, 237-0283 ENGINE AR

i02556294 SEBP3152

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[25]	STRAP-CABLE
3.	215-3249 Y	[1]	HARNESS AS-ENGINE (UNIT INJECTOR)
4.	226-0903	[1]	CABLE AS
5.	230-6279 Y	[1]	HARNESS AS-ENGINE (ECM)
6.	209-5582 CY	[1]	SWITCH GP-MAGNETIC (24-VOLT)(STARTING AID HEATER)
7.	208-9277 CM	[2]	BOLT-FLANGE HEAD (M6X1X20-MM)
8.	4P-7581	[5]	CLIP (LADDER)
9.	4P-8134	[3]	CLIP (LADDER)
10.	5P-7970 M	[1]	NUT (M8X1.25-THD)
11.	6V-4369	[1]	CLIP
12.	6V-5839 C	[4]	WASHER (11X21X2.5-MM THK)
13.	6V-6317 CM	[3]	BOLT (M10X1.5X20-MM)
14.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
15.	8T-0328	[2]	WASHER-HARD (5.5X10X1-MM THK)
16.	7I-2272 M	[2]	BOLT (M5X0.8X12-MM)
17.	8T-4205	[1]	WASHER-HARD (7.2X14.5X2-MM THK)
18.	8T-5451 M	[1]	BOLT (M6X1X12-MM)
19.	9M-1974	[1]	WASHER-HARD (8.8X16X2-MM THK)
20.	283-1226 C	[1]	BRACKET AS
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP31520262

193-3391: WIRING GP-FINE SWING

WIRING GP-FINE SWING

193-3391 WIRING GP-FINE SWING
S/N MCA1-UP; GKX1-UP
PART OF 191-5613 VALVE AR-SWING
AN ATTACHMENT

i01676113 SEBP3152

1933391 WIRING GP-FINE SWING Parts scheme

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	116-0118	[1]	CLIP
2.	193-3392	[1]	HARNESS AS-SOLENOID
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	103-2529 E		HOSE (92-CM)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
3.	111-4837	[2]	CLIP
4.	163-6722	[1]	SWITCH AS-ROCKER (FINE SWING CONTROL)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[5]	TERMINAL (MALE)
5.	7Y-8109	[1]	BRACKET AS
6.	8T-4121	[3]	WASHER-HARD (11X21X2.5-MM THK)
7.	8T-4136 M	[1]	BOLT (M10X1.5X25-MM)
8.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
9.	8T-4191 M	[1]	BOLT (M10X1.5X16-MM)
	E		ORDER BY THE CENTIMETER
	M		METRIC PART

#SEBP31520263

163-6640: WIRING GP-REFUELING PUMP

WIRING GP-REFUELING PUMP

163-6640 WIRING GP-REFUELING PUMP
S/N MCA1-UP; GKX1-UP
PART OF 176-2800 PUMP AR-REFUELING
AN ATTACHMENT

i02274736 SEBP3152

1636640 WIRING GP-REFUELING PUMP Parts scheme

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	8T-0328 C	[3]	WASHER-HARD (5.5X10X1-MM THK)
2.	3S-2093	[16]	STRAP-CABLE
3.	238-1721	[1]	WIRE AS
4.	116-0095	[1]	SWITCH AS (REFUELING PUMP, START)
	6T-9442	[1]	SWITCH GP-PUSH BUTTON
	1S-0812	[2]	SCREW-TAPPING
	3K-0835	[1]	NUT (5/8-24-THD)
	6F-0253	[1]	LOCKWASHER
	8T-8748	[1]	ADAPTER-MOUNT
	9W-0625	[1]	SWITCH AS-PUSH BUTTON
	6V-2689 BD		TUBE-HEAT SHRINK (6.35-MM DIA)
	116-0096	[1]	HARNESS AS-WIRING (REFUELING PUMP, START)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
5.	116-0097	[1]	SWITCH AS (REFUELING PUMP, STOP)
	6V-2689 BD		TUBE-HEAT SHRINK (6.35-MM DIA)
	116-0098	[1]	HARNESS AS-WIRING (REFUELING PUMP, STOP)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
6.	238-2074 C	[1]	HARNESS AS-SWITCH (REFUELING PUMP RELAY)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	3S-2093	[5]	STRAP-CABLE
	155-2270	[3]	KIT-CONNECTING PLUG (2-PIN)
			(EACH INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
7.	9X-3495	[1]	CLIP AS
8.	8T-4199 M	[1]	BOLT (M8X1.25X12-MM)
9.	8T-4224	[1]	WASHER-HARD (8.8X16X2-MM THK)
10.	149-5050	[1]	RELAY (24-VOLT)(REFUELING PUMP, START)
11.	7X-2619 CM	[2]	BOLT (M6X1X10-MM)
12.	9X-8256 C	[2]	WASHER (6.6X12X2-MM THK)
13.	213-0772 C	[1]	SWITCH AS-MAGNETIC (24-VOLT)(REFUELING PUMP RELAY)
14.	149-5050	[1]	RELAY (24-VOLT)(REFUELING PUMP, STOP)
15.	096-2591 CM	[2]	SCREW-MACHINE (M5X0.8X35-MM)
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	D		ORDER BY THE METER
	M		METRIC PART

#SEBP31520264

199-4578: DRIVE GP-FINAL

DRIVE GP-FINAL

199-4578 DRIVE GP-FINAL
S/N MCA1-304; GKX1-152
WITH MOTOR
PART OF 191-2576 POWER TRAIN AR

i01677967 SEBP3152

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	199-4579 Y	[1]	DRIVE GP-FINAL
2.	191-5606 Y	[1]	MOTOR & MTG GP-TRAVEL
	Y		SEPARATE ILLUSTRATION

#SEBP31520265

199-4579: DRIVE GP-FINAL

DRIVE GP-FINAL

199-4579 DRIVE GP-FINAL
S/N MCA1-304; GKX1-152
WITHOUT MOTOR
PART OF 199-4578 DRIVE GP-FINAL

i01678100 SEBP3152

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-2338	[2]	PLUG-PIPE
2.	7Y-0639	[1]	GEAR-SUN (21-TEETH)
3.	7Y-0642	[1]	GEAR-RING (63-TEETH)
4.	7Y-0645	[1]	CARRIER
5.	7Y-0659	[3]	GEAR-PLANETARY (22-TEETH)
6.	7Y-0661	[3]	SHAFT-PLANETARY
7.	7Y-0662	[4]	SHAFT-PLANETARY
8.	7Y-0663	[4]	GEAR-PLANETARY (20-TEETH)
9.	7Y-0667	[1]	RING-RETAINING
10.	7Y-0673	[1]	GEAR-RING (73-TEETH)
11.	7Y-0676	[3]	GEAR-PLANETARY (24-TEETH)
12.	7Y-0731	[1]	CARRIER AS
12A.	7Y-0656	[3]	SHAFT-PLANETARY
13.	7Y-1094 M	[14]	WASHER (66X102X1-MM THK)
14.	7Y-5235 M	[20]	BOLT (M24X3X190-MM)
15.	094-0577 B	[1]	PLATE (7-MM THK)
16.	094-0578 B	[1]	PLATE (8-MM THK)
17.	094-0579 B	[1]	PLATE (9-MM THK)
18.	094-0580 B	[1]	PLATE (10-MM THK)
19.	110-7231	[1]	GEAR-SUN (18-TEETH)
20.	191-2521	[1]	GEAR-SUN (23-TEETH)
21.	191-2522	[1]	RETAINER
22.	191-2523	[1]	CARRIER-PLANETARY
23.	191-2526	[1]	COVER
24.	191-2645	[1]	COUPLING
25.	196-4873	[2]	BEARING AS-BALL
26.	199-4580	[1]	HOUSING
27.	199-4581	[1]	HOUSING
28.	199-4582	[3]	BEARING AS
29.	199-4583	[11]	BEARING AS
30.	213-4737	[1]	SEAL GP-DUO-CONE
31.	093-1731	[1]	RING-RETAINING
32.	094-0584	[6]	WASHER (40.3X72X1-MM THK)
33.	095-0891	[7]	PIN-SPRING
34.	096-3216 M	[2]	SETSCREW-SOCKET (M12X1.75X12-MM)
35.	2P-3628	[1]	SEAL-O-RING
36.	7M-8485	[2]	SEAL-O-RING
37.	7Y-0595	[2]	SPACER (58X79.6X6-MM THK)
38.	7Y-0644	[1]	SPACER (163X190X8-MM THK)
39.	8T-4167	[20]	WASHER-HARD (26X44X4-MM THK)
40.	8T-4240	[3]	RING-RETAINING
41.	9X-6032 M	[12]	BOLT-SOCKET HEAD (M10X1.5X30-MM)
42.	1U-8846 B		SEALANT-GASKET
	B		USE AS REQUIRED
	M		METRIC PART

#SEBP31520266

199-4746: DRIVE GP-FINAL

DRIVE GP-FINAL

199-4746 DRIVE GP-FINAL -WITH MOTOR
S/N MCA1-304; GKX1-152
PART OF 191-2576 POWER TRAIN AR

i02061114 SEBP3152

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	199-4747 Y	[1]	DRIVE GP-FINAL
2.	191-5606 Y	[1]	MOTOR & MTG GP-TRAVEL
	Y		SEPARATE ILLUSTRATION

#SEBP31520267

199-4747: DRIVE GP-FINAL

DRIVE GP-FINAL

199-4747 DRIVE GP-FINAL -WITHOUT MOTOR
S/N MCA1-304; GKX1-152
PART OF 199-4746, 199-4760 DRIVE GP-FINAL
FIELD REPLACEMENT ORDER @@@@@199-4760@@@@@

i02063013 SEBP3152

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-2338	[2]	PLUG-PIPE
2.	7Y-0639	[1]	GEAR-SUN (21-TEETH)
3.	7Y-0642	[1]	GEAR-RING (63-TEETH)
4.	7Y-0645	[1]	CARRIER
5.	7Y-0659	[3]	GEAR-PLANETARY (22-TEETH)
6.	7Y-0661	[3]	SHAFT-PLANETARY
7.	7Y-0662	[4]	SHAFT-PLANETARY
8.	7Y-0663	[4]	GEAR-PLANETARY (20-TEETH)
9.	7Y-0667	[1]	RING-RETAINING
10.	7Y-0673	[1]	GEAR-RING (73-TEETH)
11.	7Y-0676	[3]	GEAR-PLANETARY (24-TEETH)
12.	7Y-0731	[1]	CARRIER AS
12A.	7Y-0656	[3]	SHAFT-PLANETARY
13.	7Y-1094 M	[14]	WASHER (66X102X1-MM THK)
14.	7Y-5235 M	[20]	BOLT (M24X3X190-MM)
15.	094-0577 B	[1]	PLATE (7-MM THK)
16.	094-0578 B	[1]	PLATE (8-MM THK)
17.	094-0579 B	[1]	PLATE (9-MM THK)
18.	094-0580 B	[1]	PLATE (10-MM THK)
19.	110-7231	[1]	GEAR-SUN (18-TEETH)
20.	191-2521	[1]	GEAR-SUN (23-TEETH)
21.	196-4873	[2]	BEARING AS-BALL
22.	199-4582	[3]	BEARING AS
23.	199-4583	[11]	BEARING AS
24.	199-4748	[1]	HOUSING-MOTOR
25.	199-4749	[1]	RETAINER
26.	199-4750	[1]	CARRIER-PLANETARY
27.	213-4737	[1]	SEAL GP-DUO-CONE
28.	093-1731	[1]	RING-RETAINING
29.	094-0584	[6]	WASHER (40.3X72X1-MM THK)
30.	095-0891	[7]	PIN-SPRING
31.	096-3216 M	[2]	SETSCREW-SOCKET (M12X1.75X12-MM)
32.	191-2526	[1]	COVER
33.	191-2645	[1]	COUPLING
34.	199-4580	[1]	HOUSING
35.	2P-3628	[1]	SEAL-O-RING
36.	7M-8485	[2]	SEAL-O-RING
37.	7Y-0595	[2]	SPACER (58X79.6X6-MM THK)
38.	7Y-0644	[1]	SPACER (163X190X8-MM THK)
39.	8T-4167	[20]	WASHER-HARD (26X44X4-MM THK)
40.	8T-4240	[3]	RING-RETAINING
41.	9X-6032 M	[12]	BOLT-SOCKET HEAD (M10X1.5X30-MM)
42.	1U-8846 B		SEALANT-GASKET
	B		USE AS REQUIRED
	M		METRIC PART

#SEBP31520268

199-4760: DRIVE GP-FINAL

DRIVE GP-FINAL

199-4760 DRIVE GP-FINAL -WITHOUT MOTOR
S/N MCA1-304; GKX1-152
FIELD REPLACEMENT FOR @@@@@199-4747@@@@@

i02061259 SEBP3152

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name	Comments
1.	199-4747 Y	[1]	DRIVE GP-FINAL
	Y		SEPARATE ILLUSTRATION

#SEBP31520269

227-6103: DRIVE GP-FINAL

DRIVE GP-FINAL

227-6103 DRIVE GP-FINAL -WITHOUT MOTOR
S/N MCA305-UP; GKX153-UP
PART OF 227-6104 DRIVE GP-FINAL

i02061120 SEBP3152

For full view, you need register

Parts for your 330C L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-2338	[2]	PLUG-PIPE
2.	7Y-0639	[1]	GEAR-SUN (21-TEETH)
3.	7Y-0642	[1]	GEAR-RING (63-TEETH)
4.	7Y-0645	[1]	CARRIER
5.	7Y-0659	[3]	GEAR-PLANETARY (22-TEETH)
6.	7Y-0661	[3]	SHAFT-PLANETARY
7.	7Y-0662	[4]	SHAFT-PLANETARY
8.	7Y-0663	[4]	GEAR-PLANETARY (20-TEETH)
9.	7Y-0667	[1]	RING-RETAINING
10.	7Y-0673	[1]	GEAR-RING (73-TEETH)
11.	7Y-0676	[3]	GEAR-PLANETARY (24-TEETH)
12.	7Y-0731	[1]	CARRIER AS
12A.	7Y-0656	[3]	SHAFT-PLANETARY
13.	7Y-1094 M	[14]	WASHER (66X102X1-MM THK)
14.	7Y-5235 M	[20]	BOLT (M24X3X190-MM)
15.	094-0577 B	[1]	PLATE (7-MM THK)
16.	094-0578 B	[1]	PLATE (8-MM THK)
17.	094-0579 B	[1]	PLATE (9-MM THK)
18.	094-0580 B	[1]	PLATE (10-MM THK)
19.	110-7231	[1]	GEAR-SUN (18-TEETH)
20.	191-2521	[1]	GEAR-SUN (23-TEETH)
21.	196-4873 J	[2]	BEARING AS-BALL
22.	199-4582	[3]	BEARING AS
23.	199-4583	[11]	BEARING AS
24.	199-4748 J	[1]	HOUSING-MOTOR
25.	199-4750	[1]	CARRIER-PLANETARY
26.	213-4737 J	[1]	SEAL GP-DUO-CONE
27.	227-6100 J	[1]	RETAINER
28.	227-6101 J	[2]	PLATE-WASHER
29.	227-6102 J	[2]	DOWEL
30.	093-1731	[1]	RING-RETAINING
31.	094-0584	[6]	WASHER (40.3X72X1-MM THK)
32.	095-0891	[7]	PIN-SPRING
33.	096-3216 M	[2]	SETSCREW-SOCKET (M12X1.75X12-MM)
34.	191-2526	[1]	COVER
35.	191-2645	[1]	COUPLING
36.	199-4580 J	[1]	HOUSING
37.	2P-3628	[1]	SEAL-O-RING
38.	7M-8485	[2]	SEAL-O-RING
39.	7Y-0595	[2]	SPACER (58X79.6X6-MM THK)
40.	7Y-0644	[1]	SPACER (163X190X8-MM THK)
41.	8T-0293 JM	[2]	BOLT (M12X1.75X20-MM)
42.	8T-4167	[20]	WASHER-HARD (26X44X4-MM THK)
43.	8T-4240	[3]	RING-RETAINING
44.	9X-6032 M	[12]	BOLT-SOCKET HEAD (M10X1.5X30-MM)
45.	1U-8846 B		SEALANT-GASKET

			AVAILABLE REPAIR KIT(S):
	227-6112 J		HOUSING GP-MOTOR
	B		USE AS REQUIRED
	J		KIT MARKED J SERVICES PART(S) MARKED J
	M		METRIC PART

Information:

ELECTRICAL AND STARTING SYSTEM

WIRING GP

Engine News

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/13

Special Instruction

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}
Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}

Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}

Tool Operating Manual

Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Testing and Adjusting

Electric Starting System - Test
C-9 Engines for Caterpillar Built Machines

Troubleshooting

CID 0168 FMI 01 System Voltage Low
C-9 Engine for Caterpillar Built Machines

CID 0168 FMI 00 System Voltage High
C-9 Engine for Caterpillar Built Machines

CID 0263 FMI 03 Digital Sensor Supply short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0263 FMI 04 Digital Sensor Supply short to ground
C-9 Engine for Caterpillar Built Machines

Electrical Connectors - Inspect
C-9 Engine for Caterpillar Built Machines

CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0100 FMI 04 Engine Oil Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C-9 Engine for the 973C Track-Type Loader

CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C-9 Engine for the 973C Track-Type Loader

CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0273 FMI 04 Turbo Outlet Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0041 FMI 04 8 Volt DC Supply short to ground
C-9 Engine for Caterpillar Built Machines

CID 0248 FMI 09 Cat Data Link not communicating
C-9 Engine for Caterpillar Built Machines

CID 0042 FMI 11 Inject Actuation Control Valve open/short
C-9 Engine for Caterpillar Built Machines

CID 0094 FMI 03 Fuel Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0094 FMI 04 Fuel Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0110 FMI 04 Engine Coolant Temperature short to ground
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 00 High Injector Actuation Pressure
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 03 Injector Actuation Pressure voltage high
C-9 Engine for the 973C Track-Type Loader

CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0175 FMI 04 Engine Oil Temperature short to ground
C-9 Engine for the 973C Track-Type Loader

CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs
C-9 Engine for Caterpillar Built Machines

CID 0041 FMI 03 8 Volt DC Supply short to +batt
C-9 Engine for Caterpillar Built Machines

How To Use the Functional Tests
C-9 Engine for Caterpillar Built Machines

Air Inlet Heater Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 11 Injector Actuation Pressure system fault
C-9 Engine for Caterpillar Built Machines

CID 0190 FMI 02 Loss of Engine Speed Signal
C-9 Engine for the 973C Track-Type Loader

CID 0190 FMI 11 Engine Speed Sensor mechanical failure
C-9 Engine for Caterpillar Built Machines

CID 0617 FMI 05 Air Inlet Heater Relay open/current below normal
C-9 Engine for the 973C Track-Type Loader

Cat Data Link Circuit - Test
C-9 Engine for Caterpillar Built Machines

Electrical Power Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Engine Pressure Sensor Open or Short Circuit - Test
C-9 Engine for Caterpillar Built Machines

Engine Shutdown Switch Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 02 Injector Actuation Pressure signal erratic
C-9 Engine for the 973C Track-Type Loader

CID 0342 FMI 02 Loss of Secondary Engine Speed signal
C-9 Engine for Caterpillar Built Machines

CID 0091 FMI 02 Incorrect Throttle Switch inputs
C-9 Engine for the 973C Track-Type Loader

CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0175 FMI 04 Engine Oil Temperature short to ground
C-9 Engine for Caterpillar Built Machines

CID 0320 FMI 02 Speed/Timing Sensor Loss of Signal
C-9 Engine for Caterpillar Built Machines

Injection Actuation Pressure Control Valve Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 04 Injector Actuation Pressure voltage low
C-9 Engine for the 973C Track-Type Loader

CID 0342 FMI 11 Secondary Engine Speed Sensor mechanical failure
C-9 Engine for the 973C Track-Type Loader

CID 1715 FMI 03 Engine Oil Temperature Sensor #2 short to +batt
C-9 Engine for Caterpillar Built Machines

CID 1715 FMI 04 Engine Oil Temperature Sensor #2 short to ground
C-9 Engine for Caterpillar Built Machines

Engine Pressure Sensor Open or Short Circuit - Test
C-9 Engine for the 973C Track-Type Loader

Sensors and Electrical Connectors
C-9 Engine for Caterpillar Built Machines

5 Volt Engine Pressure Sensor Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Analog Sensor Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Digital Sensor Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Engine Speed/Timing Sensor Circuit - Test
C-9 Engine for Caterpillar Built Machines

Throttle Position Sensor Circuit - Test
C-9 Engine for Caterpillar Built Machines

Throttle Switch Circuit - Test
C-9 Engine for the 973C Track-Type Loader

CID 0444 FMI 03 Start Relay short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0444 FMI 05 Start Relay open circuit
C-9 Engine for the 973C Track-Type Loader

CID 0444 FMI 06 Start Relay short to ground
C-9 Engine for the 973C Track-Type Loader

Start Relay Circuit - Test
C-9 Engine for the 973C Track-Type Loader

Sensors and Electrical Connectors
C-9 Engine for the 973C Track-Type Loader

CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for the 973C Track-Type Loader

Engine Wiring Information
C-9 Engine for Caterpillar Built Machines

User Defined Shutdown Input Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0617 FMI 06 Air Inlet Heater Relay grounded/current above norm
C-9 Engine for Caterpillar Built Machines

Service Magazine

Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2012/05/04

A New Engine Oil Grade Plug 0W20 Is Now Available {1408}
2002/04/22

Service of the Machined Terminals and the Stamped and Formed Terminals {7553}
2006/11/13

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/12

Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/06/08

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
2012/05/08

Information On Battery Cables and Wire Assemblies for Assembling at Dealer Site {4459}
2012/09/21

Caterpillar Parts SIS Catalog 330C L :

204-3604 WIRING GP-ELECTRONIC CONTROL

163-6698 WIRING GP-CONVERTER

186-4628 WIRING GP-CONSOLE

186-4572 WIRING GP-CONSOLE

170-6909 WIRING GP-CONSOLE

204-3604 WIRING GP-ELECTRONIC CONTROL

193-3391 WIRING GP-FINE SWING

163-6640 WIRING GP-REFUELING PUMP

199-4578 DRIVE GP-FINAL

199-4579 DRIVE GP-FINAL

199-4746 DRIVE GP-FINAL

199-4747 DRIVE GP-FINAL

199-4760 DRIVE GP-FINAL

Truck sale:

Caterpillar 330C L
- Crawler Excavators
MADISA

55,000

Caterpillar 330CL, Crawler Excavators, Construction
- Crawler Excavators
BLANCHARD MACHINERY CO.

48,000

Caterpillar 330CL, Crawler Excavators, Construction
- Crawler Excavators
MILTON CAT

Caterpillar 330CL
- Crawler Excavators
MILTON CAT