FUEL SYSTEM
PUMP GP-FUEL INJECTIONFILTER GP-FUEL
TANK GP-FUEL
ELECTRICAL AND STARTING SYSTEM
ALTERNATOR GP-CHARGINGBATTERY GP
FUEL SYSTEM
PUMP GP-FUEL INJECTION
#SEBP35710100
234-2919: PUMP GP-FUEL INJECTION
234-2919 PUMP GP-FUEL INJECTION
S/N CRX719-UP
PART OF 176-3180 ENGINE AR-PRIMARY
Type 2
AN ATTACHMENT
S/N CRX719-UP
PART OF 176-3180 ENGINE AR-PRIMARY
Type 2
AN ATTACHMENT
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 4B-4277 | [4] | WASHER (8.8X17.5X1.6-MM THK) | |
| 2. | 6I-0217 M | [1] | BOLT (M8X1.25X20-MM) | |
| 3. | 6I-0260 M | [3] | BOLT (M8X1.25X25-MM) | |
| 4. | 6I-0291 M | [1] | NUT (M8X1.25-THD) | |
| 5. | 6I-1090 M | [2] | BOLT (M8X1.25X40-MM) | |
| 6. | 7M-7410 | [1] | PLUG-PIPE | |
| 7. | 9F-2247 | [1] | PLUG-PIPE | |
| 8. | 100-4830 M | [1] | BOLT (M10X1.5X20-MM) | |
| 9. | 114-4363 M | [1] | BOLT (M8X1.25X12-MM) | |
| 10. | 124-3815 M | [1] | BOLT (M8X1.25X16-MM) | |
| 11. | 145-8327 | [1] | SEAL-O-RING | |
| 12. | 149-2091 | [1] | SEAL-O-RING | |
| 13. | 155-0576 | [8] | MOUNT-ISOLATION | |
| 14. | 179-7071 | [4] | BOLT (M8X1.25X20-MM) | |
| 15. | 199-9252 | [1] | SEAL-O-RING | |
| 16. | 199-9267 | [1] | SEAL-O-RING | |
| 17. | 199-9751 | [2] | SEAL-O-RING | |
| 18. | 396-6499 | [1] | CONTROL GP-VOLTAGE (12-VOLT)(LOAD PROTECTION) | |
| 1S-9593 | [2] | STRAP-CABLE | ||
| 7T-0093 | [4] | PIN-CONNECTOR (12-GA TO 14-GA) | ||
| 177-9653 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 19. | 268-4360 | [1] | SENSOR GP-TEMPERATURE (ENGINE COOLANT) | |
| 20. | 216-3446 | [1] | SENSOR GP-SPEED (ENGINE TIMING) | |
| 21. | 274-6721 | [1] | SENSOR GP-PRESSURE (ENGINE OIL) | |
| 22. | 274-6720 | [1] | SENSOR GP-PRESSURE (BOOST) | |
| 23. | 217-0100 | [4] | SPACER (8.2X12.7X25.4-MM THK) | |
| 24. | 221-1018 | [1] | CONTROL GP-UNPROGRAMMED | |
| 26. | 232-2720 | [1] | TUBE AS (CYL NO. 1)(NO.1) | |
| 27. | 232-2721 | [1] | TUBE AS (CYL NO. 2)(NO.2) | |
| 28. | 232-2722 | [1] | TUBE AS (CYL NO. 3)(NO.3) | |
| 29. | 232-2723 | [1] | TUBE AS (CYL NO. 4)(NO.4) | |
| 30. | 232-2725 | [2] | CLIP | |
| 31. | 232-2726 | [1] | CLIP | |
| 32. | 232-3149 | [3] | WASHER (8.35X16.85X1.55-MM THK) | |
| 33. | 232-3156 | [1] | GEAR-FUEL PUMP (68-TEETH) | |
| 34. | 232-3157 | [1] | BRACKET | |
| 35. | 238-8671 | [4] | CLAMP-INJECTOR | |
| 36. | 232-3168 | [1] | BRACKET-SUPPORT | |
| 37. | 232-3274 M | [4] | BOLT (M8X1.25X48.1-MM) | |
| 38. | 234-2906 | [4] | INJECTOR AS-FUEL | |
| (EACH INCLUDES) | ||||
| 38A. | 140-8718 | [1] | WASHER | |
| 38B. | 234-2900 | [1] | NOZZLE | |
| 38C. | 275-1038 | [1] | SEAL-O-RING | |
| 39. | 225-5173 | [1] | PUMP GP-FUEL INJECTION | |
| 40. | 6I-0456 M | [2] | BOLT (M8X1.25X45-MM) | |
| 41. | 217-0099 | [2] | SPACER (8.2X25X2-MM THK) | |
| 42. | 268-4360 | [1] | SENSOR GP-TEMPERATURE (AIR INLET) | |
| 278-8678 F | [1] | KIT-SENSOR (LUBRICATION OIL PRESSURE) | ||
| 278-8682 F | [1] | KIT-SENSOR (AIR PRESSURE) | ||
| F | NOT SHOWN | |||
| M | METRIC PART | |||
| R | REMANUFACTURED PART MAY BE AVAILABLE | |||
#SEBP35710101
234-3039: PUMP GP-FUEL PRM & PRIM FILTER
234-3039 PUMP GP-FUEL PRM & PRIM FILTER
S/N CRX107-647
PART OF 176-3180, 194-9477 ENGINE AR-PRIMARY
AN ATTACHMENT
S/N CRX107-647
PART OF 176-3180, 194-9477 ENGINE AR-PRIMARY
AN ATTACHMENT
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 6I-0456 M | [1] | BOLT (M8X1.25X45-MM) | |
| 2. | 120-6872 | [3] | BOLT | |
| 3. | 167-7418 | [1] | SPACER | |
| 4. | 215-9508 | [1] | FITTING (QUICK DISCONNECT, FEMALE) | |
| 5. | 215-9509 | [1] | FITTING (QUICK DISCONNECT, MALE) | |
| 6. | 226-0808 | [1] | TUBE AS | |
| 7. | 226-0809 | [1] | TUBE AS | |
| 8. | 232-7808 | [1] | PUMP AS-FUEL TRANSFER | |
| 9. | 1R-1804 | [1] | FILTER ELEMENT-WTR SEP & FUEL | |
| 10. | 232-9758 | [3] | WASHER (6.51X17.785X1.6-MM THK) | |
| 11. | 232-9762 | [1] | BRACKET | |
| 12. | 234-3063 | [1] | CLIP | |
| M | METRIC PART | |||
#SEBP35710102
235-5283: PUMP GP-FUEL PRM & PRIM FILTER
235-5283 PUMP GP-FUEL PRM & PRIM FILTER
S/N CRX648-UP
PART OF 176-3180, 194-9477 ENGINE AR-PRIMARY
Type 1
AN ATTACHMENT
S/N CRX648-UP
PART OF 176-3180, 194-9477 ENGINE AR-PRIMARY
Type 1
AN ATTACHMENT
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 234-3063 | [1] | CLIP | |
| 2. | 120-6872 J | [3] | BOLT | |
| 3. | 232-9758 J | [3] | WASHER (6.51X17.785X1.6-MM THK) | |
| 4. | 215-9508 | [1] | FITTING (QUICK DISCONNECT, FEMALE) | |
| 5. | 215-9509 | [1] | FITTING (QUICK DISCONNECT, MALE) | |
| 6. | 226-0808 | [1] | TUBE AS | |
| 7. | 226-0809 | [1] | TUBE AS | |
| 8. | 237-0285 | [1] | BRACKET | |
| 9. | 357-4187 | [1] | KIT-FUEL PRIMING PUMP | |
| (INCLUDES SPACERS & ISOLATORS) | ||||
| 9A. | 207-2757 | [1] | SEAL | |
| 9B. | 221-2014 | [1] | BOWL AS | |
| 9C. | 222-6617 | [1] | DRAIN AS | |
| 9D. | 1R-1804 | [1] | FILTER ELEMENT-WTR SEP & FUEL | |
| AVAILABLE REPAIR KIT(S): | ||||
| 240-9756 J | [1] | KIT-MOUNTING (FUEL PRIMING PUMP) | ||
| J | KIT MARKED J INCLUDES PART(S) MARKED J | |||
#SEBP35710103
235-5283: PUMP GP-FUEL PRM & PRIM FILTER
235-5283 PUMP GP-FUEL PRM & PRIM FILTER
S/N CRX648-UP
PART OF 176-3180, 194-9477 ENGINE AR-PRIMARY
Type 2
AN ATTACHMENT
S/N CRX648-UP
PART OF 176-3180, 194-9477 ENGINE AR-PRIMARY
Type 2
AN ATTACHMENT
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 234-3063 | [1] | CLIP | |
| 2. | 120-6872 J | [3] | BOLT | |
| 3. | 232-9758 J | [3] | WASHER (6.51X17.785X1.6-MM THK) | |
| 4. | 215-9508 | [1] | FITTING (QUICK DISCONNECT, FEMALE) | |
| 5. | 215-9509 | [1] | FITTING (QUICK DISCONNECT, MALE) | |
| 6. | 226-0808 | [1] | TUBE AS | |
| 7. | 226-0809 | [1] | TUBE AS | |
| 8. | 237-0285 | [1] | BRACKET | |
| 9. | 467-7011 CY | [1] | KIT-FUEL PRIMING PUMP | |
| AVAILABLE REPAIR KIT(S): | ||||
| 240-9756 J | [1] | KIT-MOUNTING (FUEL PRIMING PUMP) | ||
| C | CHANGE FROM PREVIOUS TYPE | |||
| J | KIT MARKED J INCLUDES PART(S) MARKED J | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP35710104
210-5912: TANK & MTG GP-FUEL
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 185-8411 | [2] | WASHER (14X60X4-MM THK) | |
| 2. | 203-1995 Y | [1] | TANK GP-FUEL | |
| 3. | 222-6403 | [2] | SLEEVE AS | |
| 4. | 224-4847 | [1] | CRADLE AS | |
| 224-4155 | [3] | BLOCK-RUBBER | ||
| 5. | 131-5879 | [2] | WASHER (11X32X3-MM THK) | |
| 6. | 195-3176 | [4] | MOUNT | |
| 7. | 8T-4186 M | [2] | BOLT (M10X1.5X40-MM) | |
| 8. | 8T-7930 M | [2] | BOLT (M12X1.75X160-MM) | |
| 9. | 3S-2093 | [1] | STRAP-CABLE | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP35710105
203-1995: TANK GP-FUEL
For full view, you need register
#SEBP35710106
206-5501: ALTERNATOR GP-CHARGING
206-5501 ALTERNATOR GP-CHARGING
S/N SLG1-UP
PART OF 210-4830, 210-4831, 222-7751, 251-5974 ENGINE & TRANSMISSION AR
AN ATTACHMENT
S/N SLG1-UP
PART OF 210-4830, 210-4831, 222-7751, 251-5974 ENGINE & TRANSMISSION AR
AN ATTACHMENT
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7C-9465 | [1] | SPACER (11.1X14.3X20-MM THK) | |
| 2. | 171-2213 | [1] | CIRCUIT BREAKER AS (135-AMPERE) | |
| 1H-3244 | [2] | LOCKWASHER | ||
| 6V-8187 | [2] | NUT (1/4-28-THD) | ||
| 8T-4205 | [2] | WASHER-HARD (7.2X14.5X2-MM THK) | ||
| 3. | 207-6036 Y | [1] | ALTERNATOR GP-CHARGING (12 VOLT 105 AMP) | |
| 4. | 222-4176 | [1] | BRACKET AS | |
| 5. | 222-4181 | [1] | STRAP | |
| 6. | 044-3994 | [2] | SCREW | |
| 7. | 3B-4502 | [2] | LOCKWASHER | |
| 8. | 6V-4283 | [1] | PLATE-IDENTIFICATION (ALTERNATOR RESET) | |
| 9. | 6V-7744 M | [1] | LOCKNUT (M10X1.5-THD) | |
| 10. | 8T-4121 | [4] | WASHER-HARD (11X21X2.5-MM THK) | |
| 11. | 8T-4196 M | [1] | BOLT (M10X1.5X35-MM) | |
| 12. | 8T-4224 | [3] | WASHER-HARD (8.8X16X2-MM THK) | |
| 13. | 8T-4908 M | [3] | BOLT (M8X1.25X25-MM) | |
| 14. | 8T-6685 M | [1] | BOLT (M10X1.5X110-MM) | |
| M | METRIC PART | |||
| R | REMANUFACTURED PART MAY BE AVAILABLE | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP35710107
207-6036: ALTERNATOR GP-CHARGING
207-6036 ALTERNATOR GP-CHARGING -105-AMPERE
S/N SLG1-UP
12 VOLT
PART OF 206-5501 ALTERNATOR GP-CHARGING
AN ATTACHMENT
S/N SLG1-UP
12 VOLT
PART OF 206-5501 ALTERNATOR GP-CHARGING
AN ATTACHMENT
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| (NO SERVICE PARTS AVAILABLE AT TIME OF PUBLICATION) | ||||
#SEBP35710108
211-6802: ALTERNATOR GP-CHARGING
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| (NO SERVICEABLE PARTS AVAILABLE AT TIME OF PUBLICATION) | ||||
#SEBP35710109
178-3462: BATTERY & WIRING GP
178-3462 BATTERY & WIRING GP -WITHOUT DISCONNECT SWITCH
S/N SLG1-1299
AN ATTACHMENT
S/N SLG1-1299
AN ATTACHMENT
For full view, you need register
Parts for your TH560B TELEHANDLER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9X-3404 | [1] | BATTERY (12-VOLT, MAINTENANCE FREE, WET) | |
| 2. | 191-2802 | [1] | CABLE AS-BATTERY (NEGATIVE) | |
| 1S-7251 | [1] | TERMINAL-CABLE (00-GA, 1/2-IN SCREW) | ||
| 5P-0747 E | CABLE (00-GA, BLACK)(89-CM) | |||
| 6T-0465 | [1] | COVER-TERMINAL (BLACK) | ||
| 7N-5274 | [1] | COVER AS-TERMINAL (BLACK) | ||
| 8Y-8081 E | TUBE-CONVOLUTED (400-CM) | |||
| 3S-6050 | [1] | TERMINAL AS-BATTERY (NEGATIVE) | ||
| 1M-6119 | [1] | BOLT (5/16-18X1.375-IN) | ||
| 1M-6120 | [1] | NUT (5/16-18-THD) | ||
| 3. | 192-1257 | [1] | BRACKET AS | |
| 4. | 220-4910 | [1] | CABLE AS-BATTERY (POSITIVE) | |
| 1S-7252 | [1] | TERMINAL-CABLE (00-GA, 3/8-IN SCREW) | ||
| 5P-0761 E | CABLE (00-GA, RED)(26-CM) | |||
| 8C-3056 E | CABLE (2-GA, RED)(54-CM) | |||
| 6V-9023 E | TUBE-HEAT SHRINK (12.7-MM DIA)(3-CM) | |||
| 030-1712 | [1] | TERMINAL-RING (2-GA, 1/4-IN SCREW) | ||
| 8Y-8081 E | TUBE-CONVOLUTED (78-CM) | |||
| 8N-0869 | [1] | COVER-TERMINAL (RED) | ||
| 219-4049 | [1] | TERMINAL AS | ||
| 219-4050 | [1] | TERMINAL-BATTERY | ||
| 219-6208 | [1] | TERMINAL (2-GA) | ||
| 5P-0537 | [1] | WASHER-HARD (7.2X14.5X2-MM THK) | ||
| 5P-9960 | [1] | BOLT (1/4-20X0.75-IN) | ||
| 5. | 131-3865 | [2] | STUD | |
| 6. | 3K-6060 | [2] | LOCKNUT (3/8-16-THD) | |
| 7. | 7X-0578 | [2] | WASHER-HARD (10.2X32X2.5-MM THK) | |
| 8. | 8I-4640 | [2] | CABLE AS | |
| 9. | 8I-4641 | [1] | CABLE AS | |
| 10. | 8T-4121 | [5] | WASHER-HARD (11X21X2.5-MM THK) | |
| 11. | 8T-4133 M | [3] | NUT (M10X1.5-THD) | |
| 12. | 8T-4191 M | [2] | BOLT (M10X1.5X16-MM) | |
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
Information:
FUEL SYSTEM
PUMP GP-FUEL INJECTION
Truck Engine News
Engine News
The Pop (Injector) Tester Is not Available for Fuel Injectors {0782, 1251, 1254, 1290, 1713}
2008/11/17
2008/11/17
Technical Information Bulletin
Troubleshooting the Fuel Injection System{1250, 1251, 1252}
Troubleshooting the Fuel Injection System{1250, 1251, 1252}
Troubleshooting the Fuel Injection System{1250, 1251, 1252}
Specifications
Tool Operating Manual
Using the 4C-6090 Multichannel Temperature Selector Group{0599, 0701, 0706, 1251, 1254, 1290, 1713}
Using the 4C-6090 Multichannel Temperature Selector Group{0599, 0701, 0706, 1251, 1254, 1290, 1713}
Using the 4C-6090 Multichannel Temperature Selector Group{0599, 0701, 0706, 1251, 1254, 1290, 1713}
Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286}
Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286}
Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286}
Testing and Adjusting Fuel Injection Pump and Governor on 3064 and 3066 Engines{0374, 0599, 0706}
Testing and Adjusting Fuel Injection Pump and Governor on 3064 and 3066 Engines{0374, 0599, 0706}
Testing and Adjusting Fuel Injection Pump and Governor on 3064 and 3066 Engines{0374, 0599, 0706}
Using the 143-2099 Sleeve Replacement Tool Group on 3114, 3116, and 3126 Engines{0374, 0599, 0701, 0706, 0781}
Using the 143-2099 Sleeve Replacement Tool Group on 3114, 3116, and 3126 Engines{0374, 0599, 0701, 0706, 0781}
Using the 143-2099 Sleeve Replacement Tool Group on 3114, 3116, and 3126 Engines{0374, 0599, 0701, 0706, 0781}
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
Troubleshooting
Fuel Injection Pump Circuit - Test
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines
Disassembly and Assembly
Service Magazine
