204-3604 WIRING GP-ELECTRONIC CONTROL S/N 4ZF1-UP PART OF 211-5020, 235-4129 ENGINE AR 330C EXCAVATOR

ELECTRICAL AND STARTING SYSTEM

WIRING GP

0. 204-3604 WIRING GP-
1. 204-3604 WIRING GP-
2. 193-3391 WIRING GP-
3. 229-1429 WIRING GP-
4. 223-0126 WIRING GP-
5. 223-0126 WIRING GP-
6. 223-0126 WIRING GP-
7. 217-6002 WIRING GP-
8. 217-6002 WIRING GP-
9. 217-6002 WIRING GP-
0. INFORMATION

EXCAVATOR 330C EXCAVATOR JCD
330C & 330C L Excavators JCD00001-UP (MACHINE) POWERED BY C-9 Engine SEBP3662 330C JCD (2001)

ELECTRICAL AND STARTING SYSTEM

WIRING GP

204-3604 WIRING GP-ELECTRONIC CONTROL

193-3391 WIRING GP-FINE SWING

229-1429 WIRING GP-MATERIAL HANDLER

#SEBP36620330

204-3604: WIRING GP-ELECTRONIC CONTROL

WIRING GP-ELECTRONIC CONTROL

204-3604 WIRING GP-ELECTRONIC CONTROL
S/N 4ZF1-UP
PART OF 211-5020, 235-4129 ENGINE AR

i02513979 SEBP3662

2043604 WIRING GP-ELECTRONIC CONTROL Parts scheme

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[24]	STRAP-CABLE
3.	215-3249	[1]	HARNESS AS-ENGINE (UNIT INJECTOR)
	3S-2093	[5]	STRAP-CABLE
	191-7823	[1]	RECEPTACLE AS
4.	226-0903	[1]	CABLE AS
5.	230-6279	[1]	HARNESS AS-ENGINE (ENGINE ELECTRONIC-LOWER)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	6I-4347	[4]	BOOT (4-PIN)
	100-3320	[1]	PLUG AS-CONNECTOR (2-PIN)
	111-2416	[1]	PLUG AS-CONNECTOR (2-PIN)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS & WEDGE)
	160-7690	[1]	PLUG AS-CONNECTOR (70-PIN)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
			(INCLUDES PLUG AS & WEDGE)
	214-7170 L	[1]	KIT-REPAIR (ELECTRICAL CONNECTORS)
			(FOR EXTREME COLD CLIMATES)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	3E-3371	[2]	WEDGE-RECEPTACLE LOCK (3-PIN)
	8T-8737	[8]	PLUG-SEAL
	155-2276	[3]	WEDGE-PLUG LOCK (3-PIN)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
			(INCLUDES PLUG AS & WEDGE)
	194-5226	[1]	WIRE AS (16-GA)
	194-5227	[1]	WIRE AS (14-GA)
6.	223-4453 CY	[1]	SWITCH GP-MAGNETIC (24-VOLT)(STARTING AID HEATER)
8.	4P-7581	[5]	CLIP (LADDER)
9.	4P-8134	[3]	CLIP (LADDER)
10.	5P-7970 M	[1]	NUT (M8X1.25-THD)
11.	6V-4369	[1]	CLIP
12.	6V-5839 C	[6]	WASHER (11X21X2.5-MM THK)
13.	6V-6317 CM	[2]	BOLT (M10X1.5X20-MM)
14.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
15.	8T-0328	[2]	WASHER-HARD (5.5X10X1-MM THK)
16.	7I-2272 M	[2]	BOLT (M5X0.8X12-MM)
17.	8T-4205	[1]	WASHER-HARD (7.2X14.5X2-MM THK)
18.	8T-5451 M	[1]	BOLT (M6X1X12-MM)
19.	9M-1974	[1]	WASHER-HARD (8.8X16X2-MM THK)
20.	8T-4133 CM	[2]	NUT (M10X1.5-THD)
21.	101-3129 CM	[2]	STUD (M10X1.5-THD)
	C		CHANGE FROM PREVIOUS TYPE
	L		KIT MARKED "L" PROVIDES OIL GRADE PLUGS FOR 0W20, 10W30, 15W40 OIL GRADES
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP36620331

204-3604: WIRING GP-ELECTRONIC CONTROL

WIRING GP-ELECTRONIC CONTROL

204-3604 WIRING GP-ELECTRONIC CONTROL
S/N 4ZF7986-UP; 7AZ1-UP
PART OF 211-5020 ENGINE AR
ALSO AN ATTACHMENT

i05375394 SEBP3662

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[25]	STRAP-CABLE
3.	419-0841 CY	[1]	HARNESS AS-ENGINE (UNIT INJECTOR)
4.	226-0903	[1]	CABLE AS
5.	230-6279 Y	[1]	HARNESS AS-ENGINE (ECM)
6.	398-0940 CY	[1]	SWITCH GP-MAGNETIC (24-VOLT)(STARTING AID HEATER)
7.	208-9277 M	[2]	BOLT-FLANGE HEAD (M6X1X20-MM)
8.	4P-7581	[5]	CLIP (LADDER)
9.	4P-8134	[3]	CLIP (LADDER)
10.	5P-7970 M	[1]	NUT (M8X1.25-THD)
11.	6V-4369	[1]	CLIP
12.	6V-5839	[4]	WASHER (11X21X2.5-MM THK)
13.	6V-6317 M	[3]	BOLT (M10X1.5X20-MM)
14.	7I-2272 M	[2]	BOLT (M5X0.8X12-MM)
15.	8T-0328	[2]	WASHER-HARD (5.5X10X1-MM THK)
16.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
17.	8T-4205	[1]	WASHER-HARD (7.2X14.5X2-MM THK)
18.	8T-5451 M	[1]	BOLT (M6X1X12-MM)
19.	9M-1974	[1]	WASHER-HARD (8.8X16X2-MM THK)
20.	283-1226	[1]	BRACKET AS
21.	439-4571 C	[5]	CLIP (LOOP)
22.	440-0881 CM	[5]	BOLT-SOCKET HEAD (M8X1.25-THD)
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP36620332

193-3391: WIRING GP-FINE SWING

WIRING GP-FINE SWING

193-3391 WIRING GP-FINE SWING
S/N JCD1-UP; JNK1-UP
PART OF 218-9386, 223-9291 CHASSIS AR

i01520528 SEBP3662

1933391 WIRING GP-FINE SWING Parts scheme

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	116-0118	[1]	CLIP
2.	193-3392	[1]	HARNESS AS-SOLENOID
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	103-2529 E		HOSE (92-CM)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
3.	111-4837	[2]	CLIP
4.	163-6722	[1]	SWITCH AS-ROCKER (FINE SWING CONTROL)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[5]	TERMINAL (MALE)
5.	7Y-8109	[1]	BRACKET AS
6.	8T-4121	[3]	WASHER-HARD (11X21X2.5-MM THK)
7.	8T-4136 M	[1]	BOLT (M10X1.5X25-MM)
8.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
9.	8T-4191 M	[1]	BOLT (M10X1.5X16-MM)
	E		ORDER BY THE CENTIMETER
	M		METRIC PART

#SEBP36620333

229-1429: WIRING GP-MATERIAL HANDLER

WIRING GP-MATERIAL HANDLER

229-1429 WIRING GP-MATERIAL HANDLER -MAGNET
S/N JCD1-UP; JNK1-UP
PART OF 228-3976 CONTROL AR-HYDRAULIC GENERATOR
AN ATTACHMENT

i01935835 SEBP3662

2291429 WIRING GP-MATERIAL HANDLER Parts scheme

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	228-7662	[1]	HARNESS AS-PANEL
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	102-8801	[1]	KIT-RECEPTACLE (12-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[2]	KIT-CONNECTING PLUG (2-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
2.	149-5050	[1]	RELAY (24-VOLT)(MAGNET)
3.	7X-2619 M	[1]	BOLT (M6X1X10-MM)
4.	161-3128	[1]	RELAY (24-VOLT)(MAGNET)
5.	229-2895	[1]	HARNESS AS-PLATFORM
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
	102-8801	[1]	KIT-RECEPTACLE (12-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
	155-2271	[1]	KIT-CONNECTING PLUG (4-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
6.	3S-2093 B	[10]	STRAP-CABLE
7.	228-9295	[1]	HARNESS AS-PLATFORM
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
8.	228-6295	[1]	HARNESS AS-PLATFORM
	155-2260	[2]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
	155-2271	[1]	KIT-CONNECTING PLUG (4-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
9.	229-6053	[1]	SWITCH AS-ROCKER (MAGNET)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[4]	TERMINAL (MALE)
10.	219-6932	[1]	HARNESS AS-SWITCH
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
11.	147-5321	[1]	HARNESS AS-SOLENOID
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
12.	8T-0288 M	[2]	BOLT (M5X0.8X12-MM)
13.	9X-8256	[1]	WASHER (6.6X12X2-MM THK)
	B		USE AS REQUIRED
	M		METRIC PART

#SEBP36620334

223-0126: WIRING GP-MEDIUM PRESSURE

WIRING GP-MEDIUM PRESSURE

223-0126 WIRING GP-MEDIUM PRESSURE
S/N JCD1-UP; JNK1-UP
PART OF 219-7807 CONTROL AR-AUXILIARY
Type 1
AN ATTACHMENT

i02206490 SEBP3662

2230126 WIRING GP-MEDIUM PRESSURE Parts scheme

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	222-3491	[1]	HARNESS AS-PLATFORM
	102-8804	[2]	KIT-RECEPTACLE (4-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2271	[1]	KIT-CONNECTING PLUG (4-PIN)
	155-2274	[2]	KIT-CONNECTING PLUG (6-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
2.	7K-1181 B	[6]	STRAP-CABLE
3.	8T-4196 M	[1]	BOLT (M10X1.5X35-MM)
4.	111-4837	[1]	CLIP
5.	149-5050	[1]	RELAY (24-VOLT)(HYD LOCK, QUICK CPLR, SUPPLY)
5A.	149-5050	[1]	RELAY (24-VOLT)(ROTATOR, CCW ROTATION)
5B.	149-5050	[1]	RELAY (24-VOLT)(ROTATOR, CLOCKWISE ROTATION)
6.	7X-2619 M	[1]	BOLT (M6X1X10-MM)
7.	9X-8256	[1]	WASHER (6.6X12X2-MM THK)
8.	5C-9553 M	[2]	BOLT (M6X1X16-MM)
9.	222-3493	[1]	HARNESS AS-PANEL (RELAY)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[2]	KIT-CONNECTING PLUG (2-PIN)
			(EACH INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
	3S-2093	[2]	STRAP-CABLE
10.	3S-2093 B	[46]	STRAP-CABLE
11.	223-5651	[1]	HARNESS AS-PANEL (RELAY)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	3S-2093	[2]	STRAP-CABLE
	121-1022	[2]	DIODE
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
	B		USE AS REQUIRED
	M		METRIC PART

#SEBP36620335

223-0126: WIRING GP-MEDIUM PRESSURE

WIRING GP-MEDIUM PRESSURE

223-0126 WIRING GP-MEDIUM PRESSURE
S/N JCD1-UP; JNK1-UP
PART OF 219-7807 CONTROL AR-AUXILIARY
Type 2
AN ATTACHMENT

i02206677 SEBP3662

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	222-3491	[1]	HARNESS AS-PLATFORM
	102-8804	[2]	KIT-RECEPTACLE (4-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2271	[1]	KIT-CONNECTING PLUG (4-PIN)
	155-2274	[2]	KIT-CONNECTING PLUG (6-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
2.	7K-1181 BC	[4]	STRAP-CABLE
3.	8T-4136 CM	[1]	BOLT (M10X1.5X25-MM)
4.	111-4837 C	[2]	CLIP
5.	149-5050	[1]	RELAY (24-VOLT)(HYD LOCK, QUICK CPLR, SUPPLY)
5A.	149-5050	[1]	RELAY (24-VOLT)(ROTATOR, CCW ROTATION)
5B.	149-5050	[1]	RELAY (24-VOLT)(ROTATOR, CLOCKWISE ROTATION)
6.	7X-2619 M	[1]	BOLT (M6X1X10-MM)
7.	9X-8256	[1]	WASHER (6.6X12X2-MM THK)
8.	5C-9553 M	[2]	BOLT (M6X1X16-MM)
9.	222-3493	[1]	HARNESS AS-PANEL (RELAY)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[2]	KIT-CONNECTING PLUG (2-PIN)
			(EACH INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
10.	3S-2093 B	[46]	STRAP-CABLE
11.	223-5651	[1]	HARNESS AS-PANEL (RELAY)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	3S-2093	[2]	STRAP-CABLE
	121-1022	[2]	DIODE
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
12.	8T-4121 C	[2]	WASHER-HARD (11X21X2.5-MM THK)
13.	8T-4172 CM	[1]	BOLT (M10X1.5X80-MM)
14.	4I-7889 C	[1]	SPACER (11X25X45-MM THK)
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART

#SEBP36620336

223-0126: WIRING GP-MEDIUM PRESSURE

WIRING GP-MEDIUM PRESSURE

223-0126 WIRING GP-MEDIUM PRESSURE
S/N JCD1-UP; JNK1-UP
PART OF 219-7807 CONTROL AR-AUXILIARY
Type 3
AN ATTACHMENT

i02595277 SEBP3662

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	222-3491	[1]	HARNESS AS-PLATFORM
	102-8804	[2]	KIT-RECEPTACLE (4-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2271	[1]	KIT-CONNECTING PLUG (4-PIN)
	155-2274	[2]	KIT-CONNECTING PLUG (6-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
2.	7K-1181 B	[4]	STRAP-CABLE
3.	8T-4136 M	[1]	BOLT (M10X1.5X25-MM)
4.	111-4837	[2]	CLIP
5.	149-5050	[1]	RELAY (24-VOLT)(HYD LOCK, QUICK CPLR, SUPPLY)
5A.	149-5050	[1]	RELAY (24-VOLT)(ROTATOR, CCW ROTATION)
5B.	149-5050	[1]	RELAY (24-VOLT)(ROTATOR, CLOCKWISE ROTATION)
8.	8T-0288 CM	[2]	BOLT (M5X0.8X12-MM)
9.	222-3493	[1]	HARNESS AS-PANEL (RELAY)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[2]	KIT-CONNECTING PLUG (2-PIN)
			(EACH INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
	3S-2093	[2]	STRAP-CABLE
10.	3S-2093 B	[46]	STRAP-CABLE
11.	223-5651	[1]	HARNESS AS-PANEL (RELAY)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE)
	3S-2093	[2]	STRAP-CABLE
	121-1022	[2]	DIODE
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
12.	8T-4121	[2]	WASHER-HARD (11X21X2.5-MM THK)
13.	8T-4172 M	[1]	BOLT (M10X1.5X80-MM)
14.	4I-7889	[1]	SPACER (11X25X45-MM THK)
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART

#SEBP36620337

217-6002: WIRING GP-PLATFORM

WIRING GP-PLATFORM

217-6002 WIRING GP-PLATFORM -ULTRA-HIGH DEMOLITION
S/N JNK1-UP
PART OF 216-5607 HYDRAULIC AR
Type 1
AN ATTACHMENT

i01711826 SEBP3662

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	218-3573	[1]	HARNESS AS-CHASSIS
	6V-2668	[1]	CAP-PROTECTION
	7N-9738	[1]	HOUSING-RECEPTACLE (14-GA TO 18-GA)
	121-1022	[2]	DIODE
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	155-2260	[3]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
2.	220-0920	[1]	HARNESS AS-BOX (CAB TILT)
	3E-7996	[1]	PLUG-CONNECTOR (6-PIN)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
3.	163-6720	[1]	SWITCH AS-ROCKER (CAB TILT)(CAB TILT)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[5]	TERMINAL (MALE)
4.	129-6463	[1]	SWITCH AS (CAB TILT)
5.	9G-9813 Y	[1]	ALARM GP (24-VOLT)(WARNING)
6.	224-1055	[1]	PLATE
7.	149-5050	[1]	RELAY (24-VOLT)(CAB TILT)
8.	157-3706	[1]	FILM-INSTRUCTION (CAB TILT)
9.	9X-8256	[1]	WASHER (6.6X12X2-MM THK)
10.	7X-2619 M	[1]	BOLT (M6X1X10-MM)
11.	112-6163	[1]	ACTUATOR
12.	7K-1181 B	[40]	STRAP-CABLE
	B		USE AS REQUIRED
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP36620338

217-6002: WIRING GP-PLATFORM

WIRING GP-PLATFORM

217-6002 WIRING GP-PLATFORM -ULTRA-HIGH DEMOLITION
S/N JNK1-UP
PART OF 216-5607 HYDRAULIC AR
Type 2
AN ATTACHMENT

i02187200 SEBP3662

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	225-6266	[1]	HARNESS AS-SWITCH (CAB TILT)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	6V-2668	[1]	CAP-PROTECTION
	121-1022	[2]	DIODE
	7N-9738	[1]	HOUSING-RECEPTACLE (14-GA TO 18-GA)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
2.	225-6265	[1]	HARNESS AS-PANEL
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			KIT INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
3.	163-6720	[1]	SWITCH AS-ROCKER (CAB TILT)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[5]	TERMINAL (MALE)
4.	129-6463	[1]	SWITCH AS (CAB TILT)
5.	9G-9813 Y	[1]	ALARM GP (24-VOLT)(WARNING)
6.	224-1055	[1]	PLATE
7.	149-5050	[1]	RELAY (24-VOLT)(CAB TILT)
8.	157-3706	[1]	FILM-INSTRUCTION (CAB TILT)
9.	9X-8256	[1]	WASHER (6.6X12X2-MM THK)
10.	7X-2619 M	[1]	BOLT (M6X1X10-MM)
11.	112-6163	[1]	ACTUATOR
12.	7K-1181 B	[40]	STRAP-CABLE
	B		USE AS REQUIRED
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP36620339

217-6002: WIRING GP-PLATFORM

WIRING GP-PLATFORM

217-6002 WIRING GP-PLATFORM -ULTRA-HIGH DEMOLITION
S/N JCD1-UP; JNK1-UP
PART OF 238-6262 CAB AR, 216-5607 HYDRAULIC AR
Type 1
AN ATTACHMENT

i02187207 SEBP3662

For full view, you need register

Parts for your 330C EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-6328 CY	[1]	ALARM GP (24-VOLT)
2.	233-5018 C	[1]	HARNESS AS (CAB TILT)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	121-1022	[2]	DIODE
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(EACH PLUG AS INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
3.	163-6720	[1]	SWITCH AS-ROCKER (CAB TILT)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[5]	TERMINAL (MALE)
4.	7K-1181 B	[40]	STRAP-CABLE
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	Y		SEPARATE ILLUSTRATION

Information:

ELECTRICAL AND STARTING SYSTEM

WIRING GP

Engine News

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/13

Special Instruction

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}
Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}

Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}

Tool Operating Manual

Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Testing and Adjusting

Electric Starting System - Test
C-9 Engines for Caterpillar Built Machines

Troubleshooting

CID 0168 FMI 01 System Voltage Low
C-9 Engine for Caterpillar Built Machines

CID 0168 FMI 00 System Voltage High
C-9 Engine for Caterpillar Built Machines

CID 0263 FMI 03 Digital Sensor Supply short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0263 FMI 04 Digital Sensor Supply short to ground
C-9 Engine for Caterpillar Built Machines

Electrical Connectors - Inspect
C-9 Engine for Caterpillar Built Machines

CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0100 FMI 04 Engine Oil Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C-9 Engine for the 973C Track-Type Loader

CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C-9 Engine for the 973C Track-Type Loader

CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0273 FMI 04 Turbo Outlet Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0041 FMI 04 8 Volt DC Supply short to ground
C-9 Engine for Caterpillar Built Machines

CID 0248 FMI 09 Cat Data Link not communicating
C-9 Engine for Caterpillar Built Machines

CID 0042 FMI 11 Inject Actuation Control Valve open/short
C-9 Engine for Caterpillar Built Machines

CID 0094 FMI 03 Fuel Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0094 FMI 04 Fuel Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0110 FMI 04 Engine Coolant Temperature short to ground
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 00 High Injector Actuation Pressure
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 03 Injector Actuation Pressure voltage high
C-9 Engine for the 973C Track-Type Loader

CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0175 FMI 04 Engine Oil Temperature short to ground
C-9 Engine for the 973C Track-Type Loader

CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs
C-9 Engine for Caterpillar Built Machines

CID 0041 FMI 03 8 Volt DC Supply short to +batt
C-9 Engine for Caterpillar Built Machines

How To Use the Functional Tests
C-9 Engine for Caterpillar Built Machines

Air Inlet Heater Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 11 Injector Actuation Pressure system fault
C-9 Engine for Caterpillar Built Machines

CID 0190 FMI 02 Loss of Engine Speed Signal
C-9 Engine for the 973C Track-Type Loader

CID 0190 FMI 11 Engine Speed Sensor mechanical failure
C-9 Engine for Caterpillar Built Machines

CID 0617 FMI 05 Air Inlet Heater Relay open/current below normal
C-9 Engine for the 973C Track-Type Loader

Cat Data Link Circuit - Test
C-9 Engine for Caterpillar Built Machines

Electrical Power Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Engine Pressure Sensor Open or Short Circuit - Test
C-9 Engine for Caterpillar Built Machines

Engine Shutdown Switch Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 02 Injector Actuation Pressure signal erratic
C-9 Engine for the 973C Track-Type Loader

CID 0342 FMI 02 Loss of Secondary Engine Speed signal
C-9 Engine for Caterpillar Built Machines

CID 0091 FMI 02 Incorrect Throttle Switch inputs
C-9 Engine for the 973C Track-Type Loader

CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0175 FMI 04 Engine Oil Temperature short to ground
C-9 Engine for Caterpillar Built Machines

CID 0320 FMI 02 Speed/Timing Sensor Loss of Signal
C-9 Engine for Caterpillar Built Machines

Injection Actuation Pressure Control Valve Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0164 FMI 04 Injector Actuation Pressure voltage low
C-9 Engine for the 973C Track-Type Loader

CID 0342 FMI 11 Secondary Engine Speed Sensor mechanical failure
C-9 Engine for the 973C Track-Type Loader

CID 1715 FMI 03 Engine Oil Temperature Sensor #2 short to +batt
C-9 Engine for Caterpillar Built Machines

CID 1715 FMI 04 Engine Oil Temperature Sensor #2 short to ground
C-9 Engine for Caterpillar Built Machines

Engine Pressure Sensor Open or Short Circuit - Test
C-9 Engine for the 973C Track-Type Loader

Sensors and Electrical Connectors
C-9 Engine for Caterpillar Built Machines

5 Volt Engine Pressure Sensor Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Analog Sensor Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Digital Sensor Supply Circuit - Test
C-9 Engine for Caterpillar Built Machines

Engine Speed/Timing Sensor Circuit - Test
C-9 Engine for Caterpillar Built Machines

Throttle Position Sensor Circuit - Test
C-9 Engine for Caterpillar Built Machines

Throttle Switch Circuit - Test
C-9 Engine for the 973C Track-Type Loader

CID 0444 FMI 03 Start Relay short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0444 FMI 05 Start Relay open circuit
C-9 Engine for the 973C Track-Type Loader

CID 0444 FMI 06 Start Relay short to ground
C-9 Engine for the 973C Track-Type Loader

Start Relay Circuit - Test
C-9 Engine for the 973C Track-Type Loader

Sensors and Electrical Connectors
C-9 Engine for the 973C Track-Type Loader

CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for the 973C Track-Type Loader

CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for the 973C Track-Type Loader

Engine Wiring Information
C-9 Engine for Caterpillar Built Machines

User Defined Shutdown Input Circuit - Test
C-9 Engine for Caterpillar Built Machines

CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C-9 Engine for Caterpillar Built Machines

CID 0617 FMI 06 Air Inlet Heater Relay grounded/current above norm
C-9 Engine for Caterpillar Built Machines

Service Magazine

Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2012/05/04

A New Engine Oil Grade Plug 0W20 Is Now Available {1408}
2002/04/22

Service of the Machined Terminals and the Stamped and Formed Terminals {7553}
2006/11/13

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/12

Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/06/08

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
2012/05/08

Information On Battery Cables and Wire Assemblies for Assembling at Dealer Site {4459}
2012/09/21

Caterpillar Parts SIS Catalog 330C :

204-3604 WIRING GP-ELECTRONIC CONTROL

217-6003 WIRING GP-CONTROL

186-4628 WIRING GP-CONSOLE

186-4572 WIRING GP-CONSOLE

204-3604 WIRING GP-ELECTRONIC CONTROL

193-3391 WIRING GP-FINE SWING

229-1429 WIRING GP-MATERIAL HANDLER

223-0126 WIRING GP-MEDIUM PRESSURE

217-6002 WIRING GP-PLATFORM

Truck sale:

Caterpillar 330C
- Crawler Excavators
CGT - COMPAGNIA GENERALE TRATTORI

375,750

Caterpillar 330 CF, Crawler Excavators, Construction
- Crawler Excavators
WHEELER MACHINERY CO.

379,533

Caterpillar 330 CF, Crawler Excavators, Construction
- Crawler Excavators
WHEELER MACHINERY CO.

372,345

Caterpillar 330 CF, Crawler Excavators, Construction
- Crawler Excavators
WHEELER MACHINERY CO.

330,000

Caterpillar 330 CF, Crawler Excavators, Construction
- Crawler Excavators
WHEELER MACHINERY CO.