AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

237-1962 STARTING MOTOR GP-ELECTRIC 24-VOLT Type 2 FIELD REPLACEMENT FOR @@@@@207-1556@@@@@ C-10 TRUCK ENGINE


ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GP
SWITCH GP
WIRING GP

TRUCK ENGINE C-10 TRUCK ENGINE MBJ
 C-10 Truck Engine MBJ00001-UP SEBP3681 C-10 MBJ   (2001)

ELECTRICAL AND STARTING SYSTEM

STARTING MOTOR GP
STARTING MOTOR GP-ELECTRIC
102-5836 STARTING MOTOR GP-ELECTRIC
STARTING MOTOR GP-ELECTRIC
207-1556 STARTING MOTOR GP-ELECTRIC
STARTING MOTOR GP-ELECTRIC
237-1962 STARTING MOTOR GP-ELECTRIC
STARTING MOTOR GP-ELECTRIC
237-1962 STARTING MOTOR GP-ELECTRIC
STARTING MOTOR GP-ELECTRIC
9Y-7129 STARTING MOTOR GP-ELECTRIC
 

#SEBP36810810
 

237-1962: STARTING MOTOR GP-ELECTRIC

237-1962 STARTING MOTOR GP-ELECTRIC
24-VOLT
Type 2
FIELD REPLACEMENT FOR @@@@@207-1556@@@@@
i06992648 SEBP3681
2371962 STARTING MOTOR GP-ELECTRIC Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 7M-0326 [1] CONNECTOR  
2. 9H-3757 [2] WASHER (0.516X1X0.094-IN THK)  
3. 1S-7446 [3] SCREW-MACHINE (8-32X0.437-IN)  
4. 8C-9660 [3] WASHER (4.6X7.9X0.8-MM THK)  
5. 9S-2544 [9] SCREW-HEX HEAD (8-32X11.13-MM)  
6. 7M-0327 [1] WASHER-THRUST (17.4X25.4X1.6-MM THK)  
7. 3T-3418 [1] FRAME AS-END  
  3T-3423 [1] CUP  
  3T-3424 [1] PLUG-FELT  
  9G-4101 [1] BUSHING-END  
8. 3T-9525 [1] PLATE AS-BRUSH (STARTING MOTOR)  
8A. 6T-0371 [1] INSULATOR  
8B. 5P-6298 [12] SCREW-MACHINE (10-32X0.5-IN)  
  9F-5599 [12] LOCKWASHER  
8C. 7F-3525 [6] WASHER-SPECIAL (0.207X0.39X0.09-IN THK)  
8D. 6T-0372 [1] PLATE  
8E. 3T-4709 [3] PLATE  
8F. 2L-6679 [3] PLATE-INSULATOR  
8G. 3T-4710 [3] PLATE  
8H. 6T-0363 [6] HOLDER AS-BRUSH (STARTING MOTOR)  
    (EACH INCLUDES)
8J. 3T-9494 [1] SPRING  
9. 1T-0808 [2] WASHER (0.516X0.812X0.09-IN THK)  
10. 3T-3422 [1] WIRE AS (STARTING MOTOR)  
11. 2J-8163 [2] SEAL-O-RING  
12. 7X-3373 [1] BOLT (5/16-18X0.88-IN)  
13. 3T-3434 [6] PLUG  
14. 5J-5314 [5] BOLT (5/16-18X1.5-IN)  
15. 3L-3380 [1] BUSHING-TERMINAL  
16. 036-9821 [1] WASHER  
17. 4M-1828 [1] RETAINER-SPRING  
18. 306-3998 [1] BOOT-RUBBER  
19. 9M-7609 [1] SPRING (SHIFT LEVER)  
20. 4M-1827 [1] RETAINER-SPRING  
21. 8C-3089 [1] SEAL-O-RING  
22. 4M-1853 [1] LEVER AS-SHIFT  
23. 5M-3034 [1] LOCKNUT (5/16-24-THD)  
24. 7L-2894 [4] GASKET  
25. 4M-1831 [4] PLUG-LEVER HOUSING  
26. 4M-1854 [1] SHAFT-LEVER  
27. 1H-1023 [1] SEAL-O-RING  
28. 2D-6392 [1] SEAL-O-RING  
29. 7T-3974 [1] HOUSING AS-DRIVE  
30. 6N-3826 [1] DRIVE AS-MOTOR  
31. 2H-3429 [2] RING-RETAINING  
32. 6V-1322 [4] BOLT (1/4-20X0.375-IN)  
33. 8T-4205 [4] WASHER-HARD (7.2X14.5X2-MM THK)  
34. 6N-3279 [1] INSULATOR  
35. 0S-1597 [13] BOLT (1/4-28X1-IN)  
36. 1M-9971 [1] SPACER (0.835X1.72X0.188-IN THK)  
37. 1H-2629 [3] STRIP-INSULATION  
38. 7M-0324 [1] COIL AS-FIELD  
39. 3R-8797 [12] SCREW & WASHER AS (3/8-24X0.72-IN)  
40. 7F-3488 [6] SHOE-POLE  
41. 7M-8651 [1] ARMATURE AS  
42. 7M-0325 [1] INSULATOR  
43. 3T-9524 [6] BRUSH AS  
44. 3N-3763 [1] KIT-TERMINAL (STARTING MOTOR)  
    (INCLUDES BUSHINGS & WASHERS)
46. 3R-8801 [1] CLAMP  
47. 8F-1434 [2] LOCKWASHER  
48. 6V-8188 [6] NUT (1/2-13-THD)  
49. 7X-0562 [6] WASHER-HARD (13.5X19X0.8-MM THK)  
50. 4B-2049 [6] NUT (10-32-THD)  
51. 8T-0328 [10] WASHER-HARD (5.5X10X1-MM THK)  
52. 3T-9494 [6] SPRING (STARTING MOTOR)  
53. 3E-7771 [1] HOUSING AS (STARTING MOTOR)  
54. 9G-4101 [1] BUSHING-END  
55. 3T-3424 [3] PLUG-FELT  
56. 3T-3423 [3] CUP  
57. 1M-9968 [1] BUSHING  
59. 4L-2729 [1] WASHER (0.844X1.9X0.188-IN THK)  
60. 4M-1896 [1] BUSHING-TERMINAL  
61. 045-4065 [4] SCREW-MACHINE (10-32X0.75-IN)  
62. 125-6535 [1] COVER-STARTING MOTOR  
63. 7T-9123 [1] GASKET-PLATE  
64. 338-3453 C [1] SOLENOID AS-STARTING MOTOR (24-VOLT)  
  3R-8801 [1] CLAMP  
  C   CHANGE FROM PREVIOUS TYPE
 

#SEBP36810811
 

9Y-7129: STARTING MOTOR GP-ELECTRIC

9Y-7129 STARTING MOTOR GP-ELECTRIC
12-VOLT. STARTING AID RECOMMENDED BELOW 0 DEG CELSIUS (32 DEG F)
AN ATTACHMENT
i01602766 SEBP3681
9Y7129 STARTING MOTOR GP-ELECTRIC Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 8S-2332 [3] BOLT-12 POINT HEAD (5/8-11X1.75-IN)  
2. 207-1537 CY [1] STARTING MOTOR GP-ELECTRIC  
3. 4H-7869 [1] GASKET  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

#SEBP36810812
 

175-2303: SWITCH GP-MAGNETIC

175-2303 SWITCH GP-MAGNETIC -AIR INLET HEATER
S/N MBJ2187-UP
12-VOLT
PART OF 224-5030 WIRING GP-ELECTRONIC CONTROL
ALSO AN ATTACHMENT
i01821454 SEBP3681
1752303 SWITCH GP-MAGNETIC Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 102-8802 [1] KIT-RECEPTACLE (2-PIN)  
    (INCLUDES RECEPTACLE AS & WEDGE)
2. 186-3735 [2] PIN-CONNECTOR (16-GA TO 18-GA)  
3. 1H-3338 [2] LOCKWASHER (EXTERNAL TOOTH)  
4. 012-0380 [2] LOCKWASHER (6.5X12.5X1.6-MM THK)  
5. 5C-2890 M [2] NUT (M6X1-THD)  
6. 9X-1813 E SLEEVE (16-CM)  
7. 3E-7276 [1] SWITCH AS-MAGNETIC (12-VOLT)  
  E   ORDER BY THE CENTIMETER
  M   METRIC PART
 

#SEBP36810813
 

224-5030: WIRING GP-ELECTRONIC CONTROL

224-5030 WIRING GP-ELECTRONIC CONTROL
S/N MBJ1-1086
AIR SHUTOFF FEATURE
FOR USE WITH @@@@@215-6860@@@@@
CANNOT BE USED WITH @@@@@127-3288@@@@@, @@@@@157-0098@@@@@
AN ATTACHMENT
i01780051 SEBP3681
2245030 WIRING GP-ELECTRONIC CONTROL Parts scheme 2245030 WIRING GP-ELECTRONIC CONTROL Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2M-7077 [1] SPACER (0.406X0.62X0.37-IN THK)  
2. 3E-7448 [1] CONNECTOR  
3. 3S-2093 [12] STRAP-CABLE  
4. 4P-5918 [1] CLIP  
6. 131-3201 [2] BOOT  
7. 161-1704 [1] SENSOR GP-PRESSURE (AIR INLET MANIFOLD)  
8. 175-2303 Y [1] SWITCH GP-MAGNETIC (AIR INLET HEATER)  
9. 197-8391 Y [1] SENSOR GP-TEMPERATURE (AIR INLET MANIFOLD)  
10. 197-8392 Y [1] SENSOR GP-TEMPERATURE (WATER, COOLANT)  
11. 197-8393 Y [1] SENSOR GP-PRESSURE (ATMOSPHERIC)  
12. 197-8394 Y [1] SENSOR GP-PRESSURE (ENGINE OIL)  
13. 197-8396 Y [1] SENSOR GP-SPEED (CRANKSHAFT TIMING)  
14. 197-8397 Y [1] SENSOR GP-SPEED (CAMSHAFT TIMING)  
15. 211-7888 [1] WIRE AS  
16. 227-0938 [1] HARNESS AS-WIRING (ELECTRONIC CONTROL MODULE)(AIR SHUTOFF)  
  102-8802 [1] KIT-RECEPTACLE (2-PIN)  
    (INCLUDES RECEPTACLE AS & WEDGE)
  155-2255 [1] KIT-CONNECTING PLUG (12-PIN)  
    (INCLUDES PLUG AS & WEDGE)
  155-2260 [3] KIT-CONNECTING PLUG (3-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  155-2270 [9] KIT-CONNECTING PLUG (2-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  160-7690 [1] PLUG AS-CONNECTOR (70-PIN)  
  159-9322 [1] SEAL-O-RING  
17. 132-5789 [3] CLIP (LADDER)  
18. 164-9609 [1] ELBOW-PIPE  
19. 4D-7794 [1] CLIP  
20. 4K-8864 [2] CLIP (LOOP)  
21. 4P-7581 [2] CLIP (LADDER)  
22. 4P-8134 [4] CLIP (LADDER)  
23. 5P-4115 [2] WASHER-HARD (7.2X19X2-MM THK)  
24. 6V-5048 [1] SEAL-O-RING (8.92MM ID)  
25. 6V-5049 [1] SEAL-O-RING (11.89MM ID)  
26. 6V-5215 M [1] BOLT (M8X1.25X16-MM)  
27. 6V-5839 [2] WASHER (11X21X2.5-MM THK)  
28. 6V-7981 M [1] BOLT (M10X1.5X70-MM)  
29. 6V-8214 M [2] BOLT (M6X1X20-MM)  
30. 6V-8837 M [1] BOLT (M6X1X16-MM)  
31. 8M-2770 [1] CLIP (LOOP)  
32. 8M-2771 [1] CLIP  
33. 8T-0642 M [2] BOLT (M8X1.25X14-MM)  
34. 8T-4121 [1] WASHER-HARD (11X21X2.5-MM THK)  
35. 8T-4136 M [1] BOLT (M10X1.5X25-MM)  
36. 8T-4970 M [2] BOLT (M6X1X14-MM)  
37. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
38. 9S-4191 [1] PLUG (9/16-18-THD)  
39. 9S-8752 [1] NUT-FULL (3/8-16-THD)  
40. 9X-8256 [2] WASHER (6.6X12X2-MM THK)  
41. 9X-8267 [1] WASHER (6.6X12X2-MM THK)  
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
 

#SEBP36810814
 

224-5030: WIRING GP-ELECTRONIC CONTROL

224-5030 WIRING GP-ELECTRONIC CONTROL
S/N MBJ2187-5241
AIR SHUTOFF FEATURE
FOR USE WITH @@@@@215-6860@@@@@
CANNOT BE USED WITH @@@@@127-3288@@@@@, @@@@@157-0098@@@@@
ALSO AN ATTACHMENT
i01900306 SEBP3681
2245030 WIRING GP-ELECTRONIC CONTROL Parts scheme 2245030 WIRING GP-ELECTRONIC CONTROL Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2M-7077 [1] SPACER (0.406X0.62X0.37-IN THK)  
2. 3E-7448 [1] CONNECTOR  
3. 3S-2093 C [10] STRAP-CABLE  
4. 4P-5918 [1] CLIP  
6. 131-3201 [2] BOOT  
7. 161-1704 [1] SENSOR GP-PRESSURE (AIR INLET MANIFOLD)  
8. 175-2303 Y [1] SWITCH GP-MAGNETIC (AIR INLET HEATER)  
9. 197-8391 Y [1] SENSOR GP-TEMPERATURE (AIR INLET MANIFOLD)  
10. 197-8392 Y [1] SENSOR GP-TEMPERATURE (WATER, COOLANT)  
11. 197-8393 Y [1] SENSOR GP-PRESSURE (ATMOSPHERIC)  
12. 197-8394 Y [1] SENSOR GP-PRESSURE (ENGINE OIL)  
13. 197-8396 Y [1] SENSOR GP-SPEED (CRANKSHAFT TIMING)  
14. 197-8397 Y [1] SENSOR GP-SPEED (CAMSHAFT TIMING)  
15. 211-7888 [1] WIRE AS  
16. 228-1802 C [1] HARNESS AS-WIRING (ELECTRONIC CONTROL MODULE)(AIR SHUTOFF)  
  102-8802 [1] KIT-RECEPTACLE (2-PIN)  
    (INCLUDES RECEPTACLE AS & WEDGE)
  155-2255 [1] KIT-CONNECTING PLUG (12-PIN)  
    (INCLUDES PLUG AS & WEDGE)
  155-2260 [3] KIT-CONNECTING PLUG (3-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  155-2269 [7] PLUG AS-CONNECTOR (2-PIN)  
  160-7690 [1] PLUG AS-CONNECTOR (70-PIN)  
  159-9322 [1] SEAL-O-RING  
17. 132-5789 [3] CLIP (LADDER)  
18. 164-9609 [1] ELBOW-PIPE  
19. 4D-7794 [1] CLIP  
20. 4K-8864 [2] CLIP (LOOP)  
21. 4P-8134 [4] CLIP (LADDER)  
22. 5P-4115 [2] WASHER-HARD (7.2X19X2-MM THK)  
23. 6V-5048 [1] SEAL-O-RING (8.92MM ID)  
24. 6V-5049 [1] SEAL-O-RING (11.89MM ID)  
25. 6V-5215 M [1] BOLT (M8X1.25X16-MM)  
26. 6V-5839 [2] WASHER (11X21X2.5-MM THK)  
27. 6V-6317 CM [1] BOLT (M10X1.5X20-MM)  
28. 6V-7981 M [1] BOLT (M10X1.5X70-MM)  
29. 6V-8214 M [2] BOLT (M6X1X20-MM)  
30. 6V-8837 M [1] BOLT (M6X1X16-MM)  
31. 8M-2770 [1] CLIP (LOOP)  
32. 8M-2771 [1] CLIP  
33. 8T-0642 M [2] BOLT (M8X1.25X14-MM)  
34. 8T-4121 [1] WASHER-HARD (11X21X2.5-MM THK)  
35. 8T-4970 M [2] BOLT (M6X1X14-MM)  
36. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
37. 9S-4191 [1] PLUG (9/16-18-THD)  
38. 9S-8752 [1] NUT-FULL (3/8-16-THD)  
39. 9X-8256 [2] WASHER (6.6X12X2-MM THK)  
40. 9X-8267 [1] WASHER (6.6X12X2-MM THK)  
  C   CHANGE FROM PREVIOUS TYPE
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
 

#SEBP36810815
 

224-5031: WIRING GP-ELECTRONIC CONTROL

224-5031 WIRING GP-ELECTRONIC CONTROL
S/N MBJ1052-1086
FOR USE WITH @@@@@222-1480@@@@@
ALSO AN ATTACHMENT
i01780059 SEBP3681
2245031 WIRING GP-ELECTRONIC CONTROL Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2M-7077 [1] SPACER (0.406X0.62X0.37-IN THK)  
2. 3E-7448 [1] CONNECTOR  
3. 3S-2093 [12] STRAP-CABLE  
4. 4P-5918 [1] CLIP  
6. 161-1704 [1] SENSOR GP-PRESSURE (AIR INLET MANIFOLD)  
7. 189-9108 [1] HARNESS AS-SENSOR (FUEL TEMPERATURE)  
  102-8802 [1] KIT-RECEPTACLE (2-PIN)  
    (INCLUDES RECEPTACLE AS & WEDGE)
  155-2270 [1] KIT-CONNECTING PLUG (2-PIN)  
    (INCLUDES PLUG AS & WEDGE)
8. 197-8391 Y [1] SENSOR GP-TEMPERATURE (AIR INLET MANIFOLD)  
9. 197-8392 Y [1] SENSOR GP-TEMPERATURE (WATER, COOLANT)  
10. 197-8393 Y [1] SENSOR GP-PRESSURE (ATMOSPHERIC)  
11. 197-8394 Y [1] SENSOR GP-PRESSURE (ENGINE OIL)  
12. 197-8396 Y [1] SENSOR GP-SPEED (CRANKSHAFT TIMING)  
13. 197-8397 Y [1] SENSOR GP-SPEED (CAMSHAFT TIMING)  
14. 227-0937 [1] HARNESS AS-ENGINE (ELECTRONIC CONTROL MODULE)(ADEM III)  
  155-2255 [1] KIT-CONNECTING PLUG (12-PIN)  
    (INCLUDES PLUG AS & WEDGE)
  155-2260 [3] KIT-CONNECTING PLUG (3-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  155-2270 [7] KIT-CONNECTING PLUG (2-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  160-7690 [1] PLUG AS-CONNECTOR (70-PIN)  
  159-9322 [1] SEAL-O-RING  
15. 132-5789 [3] CLIP (LADDER)  
16. 164-9609 [1] ELBOW-PIPE  
17. 4D-7794 [1] CLIP  
18. 4K-8864 [2] CLIP (LOOP)  
19. 4P-7581 [2] CLIP (LADDER)  
20. 4P-8134 [4] CLIP (LADDER)  
21. 5P-4115 [2] WASHER-HARD (7.2X19X2-MM THK)  
22. 6V-5048 [1] SEAL-O-RING (8.92MM ID)  
23. 6V-5049 [1] SEAL-O-RING (11.89MM ID)  
24. 6V-5215 M [1] BOLT (M8X1.25X16-MM)  
25. 6V-5839 [2] WASHER (11X21X2.5-MM THK)  
26. 6V-7981 M [1] BOLT (M10X1.5X70-MM)  
27. 6V-8214 M [2] BOLT (M6X1X20-MM)  
28. 6V-8837 M [1] BOLT (M6X1X16-MM)  
29. 8M-2770 [1] CLIP (LOOP)  
30. 8M-2771 [1] CLIP  
31. 8T-0642 M [2] BOLT (M8X1.25X14-MM)  
32. 8T-4121 [1] WASHER-HARD (11X21X2.5-MM THK)  
33. 8T-4136 M [1] BOLT (M10X1.5X25-MM)  
34. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
35. 9S-4191 [1] PLUG (9/16-18-THD)  
36. 9S-8752 [1] NUT-FULL (3/8-16-THD)  
37. 9X-8267 [1] WASHER (6.6X12X2-MM THK)  
38. 197-8391 Y [1] SENSOR GP-TEMPERATURE (FUEL)  
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
 

#SEBP36810816
 

224-5031: WIRING GP-ELECTRONIC CONTROL

224-5031 WIRING GP-ELECTRONIC CONTROL
S/N MBJ1087-5241
FOR USE WITH @@@@@222-1480@@@@@
ALSO AN ATTACHMENT
i01900292 SEBP3681
2245031 WIRING GP-ELECTRONIC CONTROL Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2M-7077 [1] SPACER (0.406X0.62X0.37-IN THK)  
2. 3E-7448 [1] CONNECTOR  
3. 3S-2093 [10] STRAP-CABLE  
4. 4P-5918 [1] CLIP  
6. 161-1704 [1] SENSOR GP-PRESSURE (AIR INLET MANIFOLD)  
7. 189-9108 [1] HARNESS AS-SENSOR (FUEL TEMPERATURE)  
  102-8802 [1] KIT-RECEPTACLE (2-PIN)  
    (INCLUDES RECEPTACLE AS & WEDGE)
  155-2270 [1] KIT-CONNECTING PLUG (2-PIN)  
    (INCLUDES PLUG AS & WEDGE)
8. 197-8391 Y [1] SENSOR GP-TEMPERATURE (AIR INLET MANIFOLD)  
9. 197-8392 Y [1] SENSOR GP-TEMPERATURE (WATER, COOLANT)  
10. 197-8393 Y [1] SENSOR GP-PRESSURE (ATMOSPHERIC)  
11. 197-8394 Y [1] SENSOR GP-PRESSURE (ENGINE OIL)  
12. 197-8396 Y [1] SENSOR GP-SPEED (CRANKSHAFT TIMING)  
13. 197-8397 Y [1] SENSOR GP-SPEED (CAMSHAFT TIMING)  
14. 228-1801 [1] HARNESS AS (ELECTRONIC CONTROL MODULE)(ADEM III)  
  102-8802 [1] KIT-RECEPTACLE (2-PIN)  
    (INCLUDES RECEPTACLE AS & WEDGE)
  155-2255 [1] KIT-CONNECTING PLUG (12-PIN)  
    (INCLUDES PLUG AS & WEDGE)
  155-2260 [3] KIT-CONNECTING PLUG (3-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  155-2270 [7] KIT-CONNECTING PLUG (2-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  160-7690 [1] PLUG AS-CONNECTOR (70-PIN)  
  159-9322 [1] SEAL-O-RING  
15. 132-5789 [3] CLIP (LADDER)  
16. 164-9609 [1] ELBOW-PIPE  
17. 4D-7794 [1] CLIP  
18. 4K-8864 [2] CLIP (LOOP)  
19. 4P-8134 [4] CLIP (LADDER)  
20. 5P-4115 [2] WASHER-HARD (7.2X19X2-MM THK)  
21. 6V-5048 [1] SEAL-O-RING (8.92MM ID)  
22. 6V-5049 [1] SEAL-O-RING (11.89MM ID)  
23. 6V-5215 M [1] BOLT (M8X1.25X16-MM)  
24. 6V-5839 [2] WASHER (11X21X2.5-MM THK)  
25. 6V-6317 M [1] BOLT (M10X1.5X20-MM)  
26. 6V-7981 M [1] BOLT (M10X1.5X70-MM)  
27. 6V-8214 M [2] BOLT (M6X1X20-MM)  
28. 6V-8837 M [1] BOLT (M6X1X16-MM)  
29. 8M-2770 [1] CLIP (LOOP)  
30. 8M-2771 [1] CLIP  
31. 8T-0642 M [2] BOLT (M8X1.25X14-MM)  
32. 8T-4121 [1] WASHER-HARD (11X21X2.5-MM THK)  
33. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
34. 9S-4191 [1] PLUG (9/16-18-THD)  
35. 9S-8752 [1] NUT-FULL (3/8-16-THD)  
36. 9X-8267 [1] WASHER (6.6X12X2-MM THK)  
38. 197-8391 Y [1] SENSOR GP-TEMPERATURE (FUEL)  
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
 

#SEBP36810817
 

224-6271: WIRING GP-ELECTRONIC CONTROL

224-6271 WIRING GP-ELECTRONIC CONTROL
S/N MBJ1-1086
DUAL PASSIVE
ALSO AN ATTACHMENT
i01777467 SEBP3681
2246271 WIRING GP-ELECTRONIC CONTROL Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2M-7077 [1] SPACER (0.406X0.62X0.37-IN THK)  
2. 3E-7448 [1] CONNECTOR  
3. 3S-2093 [11] STRAP-CABLE  
4. 4P-5918 [1] CLIP  
6. 161-1704 [1] SENSOR GP-PRESSURE (AIR INLET MANIFOLD)  
7. 197-8391 Y [1] SENSOR GP-TEMPERATURE (AIR INLET MANIFOLD)  
8. 197-8392 Y [1] SENSOR GP-TEMPERATURE (WATER, COOLANT)  
9. 197-8393 Y [1] SENSOR GP-PRESSURE (ATMOSPHERIC)  
10. 197-8394 Y [1] SENSOR GP-PRESSURE (ENGINE OIL)  
11. 197-8396 Y [1] SENSOR GP-SPEED (CRANKSHAFT TIMING)  
12. 197-8397 Y [1] SENSOR GP-SPEED (CAMSHAFT TIMING)  
13. 227-0937 [1] HARNESS AS-ENGINE (ELECTRONIC CONTROL MODULE)(ADEM III)  
  155-2255 [1] KIT-CONNECTING PLUG (12-PIN)  
    (INCLUDES PLUG AS & WEDGE)
  155-2260 [3] KIT-CONNECTING PLUG (3-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  155-2270 [7] KIT-CONNECTING PLUG (2-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  160-7690 [1] PLUG AS-CONNECTOR (70-PIN)  
14. 132-5789 [3] CLIP (LADDER)  
15. 164-9609 [1] ELBOW-PIPE  
16. 4D-7794 [1] CLIP  
17. 4K-8864 [2] CLIP (LOOP)  
18. 4P-7581 [2] CLIP (LADDER)  
19. 4P-8134 [4] CLIP (LADDER)  
20. 5P-4115 [2] WASHER-HARD (7.2X19X2-MM THK)  
21. 6V-5048 [1] SEAL-O-RING (8.92MM ID)  
22. 6V-5049 [1] SEAL-O-RING (11.89MM ID)  
23. 6V-5215 M [1] BOLT (M8X1.25X16-MM)  
24. 6V-5839 [2] WASHER (11X21X2.5-MM THK)  
25. 6V-7981 M [1] BOLT (M10X1.5X70-MM)  
26. 6V-8214 M [2] BOLT (M6X1X20-MM)  
27. 6V-8837 M [1] BOLT (M6X1X16-MM)  
28. 8M-2770 [1] CLIP (LOOP)  
29. 8M-2771 [1] CLIP  
30. 8T-0642 M [2] BOLT (M8X1.25X14-MM)  
31. 8T-4121 [1] WASHER-HARD (11X21X2.5-MM THK)  
32. 8T-4136 M [1] BOLT (M10X1.5X25-MM)  
33. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
34. 9S-4191 [1] PLUG (9/16-18-THD)  
35. 9S-8752 [1] NUT-FULL (3/8-16-THD)  
36. 9X-8267 [1] WASHER (6.6X12X2-MM THK)  
37. 197-8391 Y [1] SENSOR GP-TEMPERATURE (FUEL)  
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
 

#SEBP36810818
 

224-6271: WIRING GP-ELECTRONIC CONTROL

224-6271 WIRING GP-ELECTRONIC CONTROL
DUAL PASSIVE
ALSO AN ATTACHMENT
i01899704 SEBP3681
2246271 WIRING GP-ELECTRONIC CONTROL Parts scheme 2246271 WIRING GP-ELECTRONIC CONTROL Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2M-7077 [1] SPACER (0.406X0.62X0.37-IN THK)  
2. 3E-7448 [1] CONNECTOR  
3. 3S-2093 C [9] STRAP-CABLE  
4. 4P-5918 [1] CLIP  
6. 210-1747 Y [1] SENSOR GP-PRESSURE (AIR INLET MANIFOLD)  
7. 197-8391 Y [1] SENSOR GP-TEMPERATURE (AIR INLET MANIFOLD)  
8. 197-8392 Y [1] SENSOR GP-TEMPERATURE (WATER, COOLANT)  
9. 197-8393 Y [1] SENSOR GP-PRESSURE (ATMOSPHERIC)  
10. 197-8394 Y [1] SENSOR GP-PRESSURE (ENGINE OIL)  
11. 197-8396 Y [1] SENSOR GP-SPEED (CRANKSHAFT TIMING)  
12. 197-8397 Y [1] SENSOR GP-SPEED (CAMSHAFT TIMING)  
13. 228-1801 C [1] HARNESS AS (ELECTRONIC CONTROL MODULE)  
  102-8802 [1] KIT-RECEPTACLE (2-PIN)  
    (INCLUDES RECEPTACLE AS & WEDGE_
  119-3662 [20] TUBE-HEAT SHRINK (10.85-MM DIA)  
  155-2255 [1] KIT-CONNECTING PLUG (12-PIN)  
    (INCLUDES PLUG AS & WEDGE)
  155-2260 [3] KIT-CONNECTING PLUG (3-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  155-2270 [5] KIT-CONNECTING PLUG (2-PIN)  
    (EACH INCLUDES PLUG AS & WEDGE)
  160-7690 [1] PLUG AS-CONNECTOR (70-PIN)  
  159-9322 [1] SEAL-O-RING  
14. 132-5789 [3] CLIP (LADDER)  
15. 164-9609 [1] ELBOW-PIPE  
16. 4D-7794 [1] CLIP  
17. 6V-4369 [1] CLIP  
18. 4P-8134 [4] CLIP (LADDER)  
19. 5P-4115 [2] WASHER-HARD (7.2X19X2-MM THK)  
20. 6V-5048 [1] SEAL-O-RING (8.92-MM ID)  
21. 6V-5049 [1] SEAL-O-RING (11.89-MM ID)  
23. 6V-5839 [2] WASHER (11X21X2.5-MM THK)  
24. 6V-6317 M [1] BOLT (M10X1.5X20-MM)  
25. 6V-7981 M [1] BOLT (M10X1.5X70-MM)  
26. 6V-8214 M [2] BOLT (M6X1X20-MM)  
27. 6V-8837 M [1] BOLT (M6X1X16-MM)  
28. 183-4403 [1] CLIP (LOOP)  
29. 8M-2771 [1] CLIP  
30. 8T-0642 M [3] BOLT (M8X1.25X14-MM)  
31. 8T-4121 [1] WASHER-HARD (11X21X2.5-MM THK)  
32. 9M-1974 [2] WASHER-HARD (8.8X16X2-MM THK)  
33. 9S-4191 [1] PLUG (9/16-18-THD)  
34. 9S-8752 [1] NUT-FULL (3/8-16-THD)  
35. 9X-8267 [1] WASHER (6.6X12X2-MM THK)  
36. 197-8391 Y [1] SENSOR GP-TEMPERATURE (FUEL)  
37. 134-3988 [1] CLIP (LOOP)  
  C   CHANGE FROM PREVIOUS TYPE
  M   METRIC PART
  Y   SEPARATE ILLUSTRATION
 

#SEBP36810819
 

169-4191: WIRING GP-ENGINE

169-4191 WIRING GP-ENGINE
FOR USE WITH CABOVER CHASSIS, RAIL MOUNT FUEL FILTER, LEECE NEVILLE ALTERNATOR
AN ATTACHMENT
i01094753 SEBP3681
1694191 WIRING GP-ENGINE Parts scheme
  For full view, you need register

Parts for your C-10 TRUCK ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 3S-2093 [13] STRAP-CABLE  
5. 061-9593 [1] ADAPTER  
6. 101-3129 M [3] STUD (M10X1.5-THD)  
7. 110-8760 [2] STRAP  
10. 4P-8134 [1] CLIP (LADDER)  
11. 4S-4455 [4] CLIP  
12. 5C-7261 M [1] NUT (M8X1.25-THD)  
13. 5P-4115 [1] WASHER-HARD (7.2X19X2-MM THK)  
14. 6V-1889 [4] CLIP (LOOP)  
15. 6V-8801 [1] NUT (3/8-16-THD)  
16. 7X-0579 [2] WASHER-HARD (8.8X25.5X2-MM THK)  
17. 8T-4121 [12] WASHER-HARD (11X21X2.5-MM THK)  
18. 8T-4133 M [7] NUT (M10X1.5-THD)  
19. 8T-4136 M [4] BOLT (M10X1.5X25-MM)  
20. 8T-4138 M [1] BOLT (M6X1X20-MM)  
21. 8T-7934 [3] WASHER-HARD (11X21X5-MM THK)  
22. 9L-1566 [4] SUPPORT  
  M   METRIC PART
 

Information:

Truck Engine News
Cold Weather Operation Reminder {1000, 1250, 1350, 1355, 1450, 1453, 1456}
2005/08/01
Operation and Maintenance Manual
Starting the Engine
C-10, C-12 and C-15 On-Highway Engines
Cold Start Strategy
C-10, C-12 and C-15 On-Highway Engines
Starting Recommendations
Cold Weather Recommendations for On-Highway Diesel Truck Engines
Cold Weather Recommendation Charts
Cold Weather Recommendations for On-Highway Diesel Truck Engines
Special Instruction
Caterpillar PRELUB<SUP>&reg;</SUP> Diagnostics{1469}
Caterpillar PRELUB® Diagnostics{1469}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Replace Armature of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat<SUP>&reg;</SUP> Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Specifications
Electric Starting Motor
C-10 and C-12 Truck Engines
Electric Starting Motor
C-10 and C-12 Truck Engines
Electric Starting Motor
C-10 and C-12 Truck Engines
Testing and Adjusting
Electric Starting System - Test
C-10 and C-12 Truck Engines
Pinion Clearance - Adjust
C-10 and C-12 Truck Engines
Disassembly and Assembly
Electric Starting Motor - Remove and Install
C-10 and C-12 On-Highway Engines

Caterpillar Parts SIS Catalog C-10 :

STARTING MOTOR GP-ELECTRIC
237-1962 STARTING MOTOR GP-ELECTRIC
STARTING MOTOR GP-ELECTRIC
207-1556 STARTING MOTOR GP-ELECTRIC
STARTING MOTOR GP-ELECTRIC
102-5836 STARTING MOTOR GP-ELECTRIC
SENSOR GP-TEMPERATURE
197-8392 SENSOR GP-TEMPERATURE
SENSOR GP-TEMPERATURE
197-8392 SENSOR GP-TEMPERATURE
SENSOR GP-TEMPERATURE
197-8391 SENSOR GP-TEMPERATURE
SENSOR GP-TEMPERATURE
197-8391 SENSOR GP-TEMPERATURE
SENSOR GP-SPEED
201-6615 SENSOR GP-SPEED
STARTING MOTOR GP-ELECTRIC
9Y-7129 STARTING MOTOR GP-ELECTRIC
SWITCH GP-MAGNETIC
175-2303 SWITCH GP-MAGNETIC
WIRING GP-ELECTRONIC CONTROL
224-5030 WIRING GP-ELECTRONIC CONTROL
WIRING GP-ELECTRONIC CONTROL
224-5030 WIRING GP-ELECTRONIC CONTROL
WIRING GP-ELECTRONIC CONTROL
224-5031 WIRING GP-ELECTRONIC CONTROL
WIRING GP-ELECTRONIC CONTROL
224-5031 WIRING GP-ELECTRONIC CONTROL
WIRING GP-ELECTRONIC CONTROL
224-6271 WIRING GP-ELECTRONIC CONTROL
WIRING GP-ELECTRONIC CONTROL
224-6271 WIRING GP-ELECTRONIC CONTROL

Truck sale:

Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.