206-1728 WIPER & WASHER GP-WINDOW S/N SHA6498-UP PART OF 204-4164 CANOPY AR-OPEN ROPS AN ATTACHMENT 416E

OPERATOR STATION

WASHER GP-WINDOW

0. 206-1728 WIPER & WA

WIPER GP-WINDOW

1. 206-1725 WIPER GP-W

SERVICE EQUIPMENT AND SUPPLIES

CHARTS & FILMS

2. 250-7914 FILM GP

WORK TOOLS

BUCKET GP

3. 175-7877 LINK GP-SH

SERVICE EQUIPMENT AND SUPPLIES

PROTECTION GP

4. 216-0909 LOCK GP-VA

CHARTS & FILMS

5. 248-5711 PLATE & FI
6. 263-8591 PLATE & FI
7. 317-1460 PLATE & FI

OPERATOR STATION

CONSOLE GP

8. 206-1701 PROTECTION

WORK TOOLS

BUCKET GP

9. 119-1530 TRANSPORT
0. INFORMATION

BACKHOE LOADER 416E BACKHOE LOADER SHA
416E Backhoe Loader Single Tilt Center Pivot SHA00001-UP (MACHINE) POWERED BY 3054C Engine SEBP3701 416E SHA (2006)

OPERATOR STATION

WASHER GP-WINDOW

206-1727 WASHER GP-WINDOW

206-1728 WIPER & WASHER GP-WINDOW

#SEBP37010830

206-1728: WIPER & WASHER GP-WINDOW

WIPER & WASHER GP-WINDOW

206-1728 WIPER & WASHER GP-WINDOW
S/N SHA6498-UP
PART OF 204-4164 CANOPY AR-OPEN ROPS
AN ATTACHMENT

i03399321 SEBP3701

2061728 WIPER & WASHER GP-WINDOW Parts scheme

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[10]	STRAP-CABLE
2.	276-8791	[1]	CLIP
3.	8T-1118	[1]	NOZZLE AS-WASHER
4.	9R-3469	[1]	DIAPHRAGM
5.	101-0745	[1]	BLADE AS-WIPER (600-MM)(FRONT)
6.	283-3451	[1]	CONNECTOR AS
7.	213-6051	[1]	HARNESS AS-CAB (WIPER MOTOR)
	9W-0852	[1]	PIN-CONNECTOR (14-GA TO 16-GA)
	9X-3401	[4]	PIN-CONNECTOR (16-GA TO 18-GA)
	155-2265	[1]	KIT-CONNECTING PLUG (8-PIN)
	155-2271	[2]	KIT-CONNECTING PLUG (4-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
	8T-8737	[3]	PLUG-SEAL
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	9W-0844	[5]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	180-9340	[15]	SOCKET-CONNECTOR (14-GA TO 18-GA)
	8L-8413	[15]	STRAP-CABLE (WHITE)
	9R-9442	[2]	TERMINAL
	2L-8069	[1]	TERMINAL-RING (2-GA TO 10-GA, 3/8-IN SCREW)
	5P-4571	[2]	TERMINAL-BLADE (14-GA TO 16-GA)
	119-3662 E		TUBE-HEAT SHRINK (10.85-MM DIA)(7-CM)
	125-7874 E		TUBE-HEAT SHRINK (5.72-MM DIA)(5-CM)
	6V-2689 D		TUBE-HEAT SHRINK (6.35-MM DIA)(0.1-M)
8.	154-5410	[1]	ARM-WINDOW WIPER
9.	186-2589 Y	[1]	MOTOR GP-WINDOW WIPER (FRONT)
10.	214-3763	[1]	TANK GP-WINDOW WASHER
	6T-1375	[2]	PUMP AS-WASHER
	8E-8293	[2]	GROMMET
	214-3742	[1]	TANK-WASHER
	254-5683	[1]	CAP
11.	6V-7357 M	[1]	BOLT (M6X1X25-MM)
12.	8T-4205	[1]	WASHER-HARD (7.2X14.5X2-MM THK)
13.	144-0195 E		HOSE (217-CM)
13A.	144-0195 E		HOSE (79-CM)
13B.	144-0195 E		HOSE (297-CM)
13C.	144-0195 E		HOSE (15-CM EACH)
14.	156-0283	[2]	WASHER-HARD (8.4X35X2.5-MM THK)
15.	9X-8372	[1]	FILM-INSTRUCTION (WASHER FILL)
16.	8T-5093 M	[1]	BOLT-LOCKING (M8X1.25X25-MM)
17.	6K-9632	[1]	TEE
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP37010831

206-1725: WIPER GP-WINDOW

WIPER GP-WINDOW

206-1725 WIPER GP-WINDOW
S/N SHA1-UP
PART OF 204-4161, 204-4162, 228-4602 CAB AR-ENCLOSED ROPS
AN ATTACHMENT

i02098566 SEBP3701

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	5C-8811	[1]	BLADE AS-WIPER (500-MM)(REAR)
2.	101-0745	[1]	BLADE AS-WIPER (600-MM)(FRONT)
3.	154-5410	[1]	ARM-WINDOW WIPER (FRONT)
4.	160-2169	[2]	SPACER (7X11X8.4-MM THK)
5.	186-2589 Y	[1]	MOTOR GP-WINDOW WIPER (FRONT)
6.	214-4709	[1]	SWITCH AS-ROCKER (WIPER, WASHER, REAR)
	111-7899	[1]	GASKET
7.	220-2000	[1]	MOTOR GP-WINDOW WIPER (REAR)
	186-3735	[5]	PIN-CONNECTOR (16-GA TO 18-GA)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
8.	220-2001	[1]	ARM AS-WIPER (REAR)
	136-3194	[1]	NOZZLE AS-WASHER
	194-5171 E		HOSE (35-CM)
9.	223-8263	[1]	PLATE
10.	229-0306	[1]	PLATE
11.	6V-7357 M	[1]	BOLT (M6X1X25-MM)
12.	8T-4138 M	[2]	BOLT (M6X1X20-MM)
13.	8T-4171 M	[4]	BOLT (M6X1X12-MM)
14.	8T-4205	[9]	WASHER-HARD (7.2X14.5X2-MM THK)
15.	5C-2890 M	[1]	NUT (M6X1-THD)
16.	8T-4971 M	[1]	BOLT (M6X1X30-MM)
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP37010832

250-7914: FILM GP

FILM GP

250-7914 FILM GP
S/N SHA1-UP
PART OF 213-9284 CHASSIS AR

i02364822 SEBP3701

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Pos.	Qty	Parts name
1.	[1]	FILM-IDENTIFICATION (416E, RH)
2.	[1]	FILM-IDENTIFICATION (BOOM, RH)
3.	[1]	FILM-IDENTIFICATION (416E, LH)
4.	[1]	FILM-IDENTIFICATION (BOOM, LH)

#SEBP37010833

175-7877: LINK GP-SHIPPING

LINK GP-SHIPPING

175-7877 LINK GP-SHIPPING
S/N SHA1-UP
REQUIRED WHEN NO BACKHOE BUCKET IS INSTALLED
AN ATTACHMENT

i01411821 SEBP3701

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name	Comments
	120-9286	[1]	PLATE

#SEBP37010834

216-0909: LOCK GP-VANDALISM

LOCK GP-VANDALISM

216-0909 LOCK GP-VANDALISM
S/N SHA1-UP
FOR USE WITH SINGLE TILT LOADER
AN ATTACHMENT

i02110453 SEBP3701

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name	Comments
	246-2641 J	[1]	PADLOCK GP (VANDALISM GUARD)
	J		REQUIRES 5P-8500 KEY

#SEBP37010835

248-5711: PLATE & FILM GP

PLATE & FILM GP

248-5711 PLATE & FILM GP
S/N SHA1-UP
PART OF 213-9284 CHASSIS AR

i02120967 SEBP3701

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
225-4150	[1]	PLATE-SERVICE INFORMATION (MACHINE)
		(ON SERVICE PLATE ON MAIN FRAME TOWER)
239-6989	[1]	PLATE-SERIAL NUMBER (MACHINE)
		(ON MAIN FRAME TOWER)

A	[1]	PLATE-SERIAL NUMBER (ENGINE)

231-9361	[1]	FILM-IDENTIFICATION (FUSE, RELAY)
		(UNDER RH CONSOLE COVER THAT COVERS THE POWER DISTRUBUTION BLOCK. ORIENT FILM SUCH THAT IT CAN BE READ WHEN THE COVER
		IS OPEN & THE BLOCK IS EXPOSED)
	[1]	FILM-INSTRUCTION (BOOM LOCK)
		(NEXT TO BOOM LOCK ON RH CONSOLE)
	[1]	FILM-INSTRUCTION (VARIABLE SPEED)
		(ON RH CONSOLE NEXT TO GOVERNER CONTROL HANDLE)
252-2157	[4]	FILM-INFORMATION (TIE-DOWN)
		(APPLY 2 FILMS, ONE ON EACH SIDE OF THE MACHINE ON THE MAIN FRAME ABOVE THE FRONT AXLE, ABOVE THE TIE DOWN MOUNTING
		PLATE. APPLY THE OTHER 2 FILMS IN THE REAR OF THE MACHINE ON THE MAIN FRAME NEXT TO THE TIE DOWN HOLES UNDER THE
		SWING CYLINDERS)
134-7258	[1]	FILM-INFORMATION (EXTENDED LIFE COOLANT)
		(NEXT TO RADIATOR CAP. ORIENT FILM SUCH THAT IT CAN BE READ FROM THE LH SIDE OF THE MACHINE)
159-8033	[1]	FILM-IDENTIFICATION (12-VOLT)
		(INSIDE BATTERY BOX DOOR 90 +/-5-MM FROM THE BOTTOM EDGE (SAME AS STACKING THE WARNING BATTERY FILM & THE 12 VOLT
		FILM ON TOP OF EACH OTHER) & CENTERED BELOW THE WARNING BATTERY FILM)
226-1242	[2]	FILM-WARNING (CRUSH HAZARD, STAY BACK, U.S.)
		(ON BOOM 700-MM +/-5 UP FROM CENTER LINE OF SWING & BOOM LOWER FOOT PIN & 65-MM +/-5 OVER FROM INSIDE OF THE REAR EDGE
		OF BOOM WRAPPER PLATE)
239-9429	[1]	FILM-WARNING (ARM BRACE, READ OMM, U.S.)
		(ON LH SIDE OF THE MACHINE ON SAFETY BRACE CENTERED FROM TOP TO BOTTOM & FROM SIDE TO SIDE)
225-0313	[1]	FILM-WARNING (JUMP START, READ OMM, U.S.)
		(INSIDE OF BATTERY BOX DOOR 150 +/-5-MM FROM THE BOTTOM EDGE (SAME AS STACKING THE NO STEP FILM ON TOP OF THE 12 VOLT
		FILM) & THE RIGHT EDGE OF THE FILM 210 +/-5-MM FROM LEFT SIDE (SAME AS THE NO STEP FILM PLACED SIDE BY SIDE THE
		WARNING BATTERY FILM)
255-0791	[1]	FILM-WARNING (READ OMM)
		(ON RH CONSOLE UNDER KEYSWITCH IN AREA PROVIDED. UNIVERSAL FILM IS LOCATED ON THE UPPER HALF & THE SEATBELT IS ON THE
		THE LOWER HALF)
255-0792	[1]	FILM-WARNING (SEAT BELT)
		(ON RH CONSOLE UNDER KEYSWITCH IN AREA PROVIDED. UNIVERSAL FILM IS LOCATED ON THE UPPER HALF & THE SEATBELT IS ON THE
		LOWER HALF)
219-0302	[1]	FILM-WARNING (NO WELD, NO DRILL, READ OMM)
		(ON LH A-POST 350 +/-5-MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO DRILL & THE ROPS/FOPS FILM IN THE
		LOWER POSITION)
225-0041	[1]	FILM-INFORMATION (ROPS, FOPS, READ OMM)
		(ON LH A-POST 350 +/-5-MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO
		DRILL & THE ROPS/FOPS FILM IN THE LOWER POSITION)
124-2456	[1]	FILM-INSTRUCTION (NO STEP)
		(POSITION INSIDE BATTERY BOX DOOR 75 +/- 5-MM FROM THE RIGHT EDGE & THE TOP EDGE IS EVEN WITH THE 12 VOLT FILM)
224-8945	[1]	FILM-WARNING (DO NOT USE ETHER, U.S.)
		(UNDER HOOD ON THE PRE-CLEANER UNDER THE SERVICE FILM. ORIENT FILM SUCH THAT IT CAN
		BE READ FROM THE LEFT SIDE OF THE MACHINE)
258-9999	[4]	FILM-IDENTIFICATION (LIFT EYE LOCATION)
		(APPLY A TOTAL OF 4 FILMS. THE FIRST 2 FILMS ARE TO BE APPLIED TO THE FRONT SIDE OF THE FRONT AXLE BETWEEN THE CHASSIS
		& WHEEL ASSEMBLY ON THE LH & RH SIDE OF THE MACHINE. THE REMAINDER 2 FILMS ARE TO BE APPLIED TO THE STAB PAD CENTERED
		UNDER THE LIFTING HOLE ORIENTED WITH THE ARROW POINTING UP WHEN THE STABILIZER IS IN THE UPPER WARD POSITION)
240-7094	[2]	FILM-WARNING (NO ENTRANCE, EXIT, READ OMM)
		(ON THE REAR OF THE CAB STRUCTURE AT THE BOTTOM 50 +/-5-MM FROM THE RED REFLECTOR TOWARD THE CENTER OF THE MACHINE FOR)
		BOTH FILMS, CENTERED FROM TOP TO BOTTOM)
159-3590	[1]	FILM-IDENTIFICATION (WATER SEPARATOR)
		(ON LEFT SIDE OF THE MAIN FRAME NEXT TO THE FUEL TANK. 20-MM +/- 10-MM FROM THE FUEL
		TANK BRACKET & UP FROM THE BOTTOM EDGE OF THE MAIN FRAME 50-MM +/- 10-MM)
	[1]	FILM-IDENTIFICATION (FUSE PANEL)
		(INSIDE RH CONSOLE ACCESS PANEL. ORIENT FILM SUCH THAT IS CAN BE READ WHILE STANDING ON THE GROUND WITH THE ACCESS DOOR
		OPEN & VIEWING FILM)
	[1]	FILM-IDENTIFICATION (LUBRICATION POINTS)
		(UNDER THE HOOD ON PRE-CLEANER, REMOVE SUPPLIER FILM & ORIENT FILM SUCH THAT IT
		CAN BE READ FROM THE LEFT SIDE OF THE MACHINE)
252-8435	[1]	FILM-IDENTIFICATION (START SWITCH, READ OMM)
		(ON RH CONSOLE AROUND KEYSWITCH)
259-4401	[1]	FILM-WARNING (HOT FLUID UND PRESS, READ OMM)
		(ON RADIATOR CAP ORIENTED SUCH THAT IT CAN BE READ FROM THE LH SIDE OF THE MACHINE)
289-3412	[1]	FILM-COVER (PROTECT)
		IN THE BATTERY BOX ON LEFT HAND SIDE. FILM SHOULD BE 150 +/- 5-MM UP FROM THE BOTTOM OF
		THE BOX & LEVEL WITH THE BOTTOM OF BOX CENTERED FROM SIDE TO SIDE)
A		NOT PART OF THIS GROUP

#SEBP37010836

263-8591: PLATE & FILM GP

PLATE & FILM GP

263-8591 PLATE & FILM GP
S/N SHA1-UP
PART OF 216-8801, 216-8821 BUCKET GP-MULTIPURPOSE
AN ATTACHMENT

i02444490 SEBP3701

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name	Comments
1.	247-6118	[2]	FILM-WARNING (CRUSH HAZARD, STAY BACK)

#SEBP37010837

317-1460: PLATE & FILM GP

PLATE & FILM GP

317-1460 PLATE & FILM GP -MACHINE
S/N SHA1-UP
AN ATTACHMENT

i03710642 SEBP3701

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
225-4150	[1]	PLATE-SERVICE INFORMATION (MACHINE)
		(ON SERVICE PLATE ON MAIN FRAME TOWER)
239-6989	[1]	PLATE-SERIAL NUMBER (MACHINE)
		(ON MAIN FRAME TOWER)

193-5913	[6]	PLUG

258-9999	[4]	FILM-IDENTIFICATION (LIFT EYE LOCATION)
		(2-ON THE FRONT SIDE OF THE FRONT AXLE BETWEEN THE CHASSIS & WHEEL ASSEMBLY ON THE LH & RH SIDE OF THE MACHINE
		2- ON THE STABILIZER PAD UNDER THE LIFTING HOLE ORIENTED WITH THE ARROW POINTING UP WHEN THE STABILIZER IS
		IN THE UPPER WARD POSITION)
289-3412	[1]	FILM-COVER (PROTECT)
		(IN THE BATTERY BOX ON LH SIDE, 150-MM UP FROM THE BOTTOM OF
		THE BOX & LEVEL WITH THE BOTTOM OF BOX CENTERED FROM SIDE TO SIDE)
159-8033	[1]	FILM-IDENTIFICATION (12-VOLT)
		(INSIDE BATTERY BOX DOOR CENTERED FROM SIDE TO SIDE ABOVE THE JUMP START WARNING FILM & CENTERED FROM TOP TO BOTTOM
		BETWEEN THE JUMP START FILM & THE BEND IN THE DOOR)
	[1]	FILM-IDENTIFICATION (FUSE PANEL)
		(INSIDE RH CONSOLE ACCESS PANEL. ORIENT FILM SUCH THAT IS CAN BE READ WHILE STANDING ON THE GROUND WITH THE ACCESS DOOR
		OPEN & VIEWING FILM)
231-9361	[1]	FILM-IDENTIFICATION (FUSE, RELAY)
		(UNDER RH CONSOLE COVER THAT COVERS THE POWER DISTRUBUTION BLOCK. ORIENT FILM SUCH THAT IT CAN BE READ WHEN THE COVER
		IS OPEN & THE BLOCK IS EXPOSED)
252-8435	[1]	FILM-IDENTIFICATION (START SWITCH, READ OMM)
		(ON RH CONSOLE AROUND KEYSWITCH)
	[1]	FILM-IDENTIFICATION (LUBRICATION POINTS)
		(UNDER THE HOOD ON PRE-CLEANER, ORIENT FILM SUCH THAT IT CAN BE READ FROM THE LEFT SIDE OF THE MACHINE)
134-7258	[1]	FILM-INFORMATION (EXTENDED LIFE COOLANT)
		(ON SHUNT TANK NEXT TO RADIATOR CAP. ORIENT FILM SUCH THAT IT CAN BE READ FROM THE LH SIDE OF THE MACHINE)
225-0041	[1]	FILM-INFORMATION (ROPS, FOPS, READ OMM)
		(ON LH A-POST 350-MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO
		DRILL & THE ROPS/FOPS FILM IN THE LOWER POSITION)
252-2157	[4]	FILM-INFORMATION (TIE-DOWN)
		(2-ON EACH SIDE OF THE MACHINE ON THE MAIN FRAME ABOVE THE FRONT AXLE, ABOVE THE TIE DOWN MOUNTING PLATE. CENTERED TOP
		TO BOTTOM & LEFT TO RIGHT
		2-IN THE REAR OF THE MACHINE ON THE MAIN FRAME NEXT TO THE TIE DOWN HOLES UNDER THE
		SWING CYLINDER)
124-2456	[1]	FILM-INSTRUCTION (NO STEP)
		(INSIDE BATTERY BOX DOOR 75-MM FROM THE RIGHT EDGE & THE TOP EDGE IS EVEN WITH THE 12-VOLT FILM)
	[1]	FILM-INSTRUCTION (BOOM LOCK)
		(NEXT TO BOOM LOCK ON RH CONSOLE)
	[1]	FILM-INSTRUCTION (VARIABLE SPEED)
		(ON RH CONSOLE NEXT TO GOVERNER CONTROL HANDLE)
219-0302	[1]	FILM-WARNING (NO WELD, NO DRILL, READ OMM)
		(ON LH A-POST 350-MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO DRILL & THE ROPS/FOPS FILM IN THE
		LOWER POSITION)
224-8946	[1]	FILM-WARNING (NO ETHER SPRAY/AIR INTK, INTL)
		(ON BOTTOM OF PRECLEANER HOOD UNDER THE SERVICE FILM)
225-0312	[1]	FILM-WARNING (JUMP START, READ OMM, INTL)
		(ON INSIDE OF BATTERY BOX DOOR CENTERED ABOVE DOOR LATCH & 75-MM UP FROM THE EDGE OF DOOR)
226-1240	[2]	FILM-WARNING (CRUSH HAZARD, STAY BACK, INTL)
		(ON BOOM 700-MM UP FROM CENTER LINE OF SWING & BOOM LOWER FOOT PIN
		& 65-MM OVER FROM INSIDE OF THE REAR EDGE OF BOOM WRAPPER PLATE)
239-9430	[1]	FILM-WARNING (ARM BRACE, READ OMM, INTL)
		(ON SAFETY BRACE OF LH SIDE OF THE MACHINE CENTERED FROM TOP TO BOTTOM & SIDE TO SIDE)
240-7095	[2]	FILM-WARNING (NO ENTRANCE, EXIT, READ OMM)
		(ON REAR OF THE CAB STRUCTURE AT THE BOTTOM 50-MM FROM THE RED REFLECTOR TOWARD THE CENTER OF THE MACHINE FOR BOTH
		FILMS, CENTERED FROM TOP TO BOTTOM)
255-0793	[1]	FILM-WARNING (READ OMM)
		(ON RIGHT CONSOLE UNDER KEYSWITCH)
255-0794	[1]	FILM-WARNING (SEAT BELT)
		(ON RIGHT CONSOLE UNDER KEYSWITCH)
259-4402	[1]	FILM-WARNING (HOT FLUID UNDER PRESSURE)
		(ON RADIATOR CAP ORIENTED SUCH THAT IT CAN BE READ FROM THE LH SIDE OF THE MACHINE)

#SEBP37010838

206-1701: PROTECTION GP-VANDALISM

PROTECTION GP-VANDALISM

206-1701 PROTECTION GP-VANDALISM -ROTATING GUARD
S/N SHA1-UP
PART OF 204-4160, 204-4164 CANOPY AR-OPEN ROPS
AN ATTACHMENT

i02098370 SEBP3701

2061701 PROTECTION GP-VANDALISM Parts scheme

For full view, you need register

Parts for your 416E BACKHOE LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	206-1852	[1]	COVER-VANDALISM
2.	206-1853	[2]	BUSHING
3.	206-1855	[1]	PLATE
4.	206-1856	[1]	BRACKET
5.	226-0291 J	[1]	LOCK AS
6.	129-3178 M	[2]	LOCKNUT (M6X1-THD)
7.	174-8131 M	[1]	SCREW-TRUSS HEAD (M4X0.7X12-MM)
8.	232-4636	[2]	BOLT-CARRIAGE (M6X1X25-MM)
9.	8C-9660	[1]	WASHER (4.6X7.9X0.8-MM THK)
10.	8T-2659 M	[1]	LOCKNUT (M4X0.7-THD)
11.	9X-2038	[2]	WASHER (7X19X2-MM THK)
	J		REQUIRES 5P-85OO KEY
	M		METRIC PART