ELECTRICAL AND STARTING SYSTEM
WIRING GPPOWER TRAIN
AXLE GPELECTRICAL AND STARTING SYSTEM
WIRING GP#SEBP38450450
271-4010: WIRING GP-SENSOR
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3S-2093 | [1] | STRAP-CABLE | |
| 2. | 4V-1939 | [4] | CLAMP | |
| 3. | 107-4749 | [2] | PLATE | |
| 4. | 7K-1181 | [1] | STRAP-CABLE | |
| 5. | 271-4011 | [1] | HARNESS AS-SENSOR | |
| 155-2260 | [1] | KIT-CONNECTING PLUG (3-PIN) | ||
| (INCLUDES PLUG AS & WEDGE) | ||||
| 102-8803 | [1] | KIT-RECEPTACLE (3-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 9X-3401 | [3] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| -OR- | ||||
| 126-1767 | [3] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 114-8843 E | SLEEVE-PLASTIC (40-CM) | |||
| 9X-3402 | [3] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| -OR- | ||||
| 126-1768 | [3] | SOCKET-CONNECTOR (14-GA TO 16-GA) | ||
| 1P-0810 B | TAPE-ELECTRICAL | |||
| 8T-2225 E | TUBE-HEAT SHRINK (25.4-MM DIA)(10-CM) | |||
| 6. | 4P-7581 | [1] | CLIP (LADDER) | |
| 7. | 8T-4121 | [3] | WASHER-HARD (11X21X2.5-MM THK) | |
| 8. | 8T-4133 M | [2] | NUT (M10X1.5-THD) | |
| 9. | 8T-4136 M | [1] | BOLT (M10X1.5X25-MM) | |
| 10. | 8M-2773 | [3] | CLIP (LOOP) | |
| 11. | 9X-2480 M | [4] | BOLT (M6X1X45-MM) | |
| 12. | 9X-8256 | [4] | WASHER (6.6X12X2-MM THK) | |
| B | USE AS REQUIRED | |||
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
#SEBP38450451
275-0023: WIRING GP-SENSOR
275-0023 WIRING GP-SENSOR -TILT POSITION
S/N N1A1-UP
PART OF 244-3375, 244-3396, 325-2745, 334-0443, 344-2861, 377-4529 CONTROL AR-HIGH LIFT
S/N N1A1-UP
PART OF 244-3375, 244-3396, 325-2745, 334-0443, 344-2861, 377-4529 CONTROL AR-HIGH LIFT
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3S-2093 | [1] | STRAP-CABLE | |
| 2. | 4V-1939 | [4] | CLAMP | |
| 3. | 107-4749 | [2] | PLATE | |
| 4. | 7K-1181 | [2] | STRAP-CABLE | |
| 5. | 275-0025 | [1] | HARNESS AS-SENSOR | |
| 6. | 4P-7581 | [1] | CLIP (LADDER) | |
| 7. | 8T-4121 | [3] | WASHER-HARD (11X21X2.5-MM THK) | |
| 8. | 8T-4133 M | [2] | NUT (M10X1.5-THD) | |
| 9. | 8T-4136 M | [1] | BOLT (M10X1.5X25-MM) | |
| 10. | 9M-8406 | [3] | CLIP (LOOP) | |
| 11. | 9X-2480 M | [4] | BOLT (M6X1X45-MM) | |
| 12. | 9X-8256 | [4] | WASHER (6.6X12X2-MM THK) | |
| M | METRIC PART | |||
#SEBP38450452
253-3945: WIRING GP-WASTE HANDLER
253-3945 WIRING GP-WASTE HANDLER
S/N N1A1-UP
PART OF 247-8561 ACTUATOR GP-POWER
S/N N1A1-UP
PART OF 247-8561 ACTUATOR GP-POWER
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7K-1181 | [11] | STRAP-CABLE | |
| 2. | 157-1364 | [1] | SWITCH AS-TOGGLE (POWER GUARD ACTUATOR) | |
| 102-8805 | [1] | KIT-RECEPTACLE (6-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 6T-3631 | [2] | NUT-HEX (15/32-32-THD) | ||
| 6T-3632 | [1] | LOCKWASHER | ||
| 6T-3633 | [1] | RING-LOCKING | ||
| 186-3735 | [1] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 3. | 249-6463 | [1] | FILM-IDENTIFICATION (POWER GUARD ACTUATOR SWITCH) | |
| 4. | 266-7230 | [1] | HARNESS AS-CONTROL (POWER GUARD ACTUATOR) | |
| 155-2270 | [1] | KIT-CONNECTING PLUG (2-PIN) | ||
| 155-2274 | [1] | KIT-CONNECTING PLUG (6-PIN) | ||
| (EACH PLUG KIT INCLUDES PLUG AS & WEDGE) | ||||
| 5. | 130-5300 | [1] | CLIP | |
| 6. | 186-3221 | [1] | WIRE AS | |
| 7. | 3T-2662 | [1] | CIRCUIT BREAKER AS (15-AMPERE, AUTOMATIC RESET)(POWER GUARD ACTUATOR) | |
| 6V-8376 | [2] | SCREW-MACHINE (8-32X0.25-IN) | ||
| 9B-7233 | [2] | LOCKWASHER | ||
| 8. | 4D-8123 | [1] | CLIP | |
| 9. | 5M-6668 | [2] | SCREW-MACHINE (8-32X0.75-IN) | |
| 10. | 5P-9085 | [3] | CLIP (LOOP) | |
#SEBP38450453
214-6161: AXLE AR-FIXED
214-6161 AXLE AR-FIXED -FRONT, STANDARD DIFFERENTIAL
S/N N1A1-UP
PART OF 244-5421, 340-4746 LOGGING AR
S/N N1A1-UP
PART OF 244-5421, 340-4746 LOGGING AR
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS#SEBP38450454
214-9398: AXLE AR-FIXED
214-9398 AXLE AR-FIXED -FRONT, STANDARD DIFFERENTIAL
S/N N1A1-3212
PART OF 334-0419 AXLE AR-FIXED & OSCILLATING, 334-0422, 334-0423, 334-0428, 334-0429, 334-0430 CONFIGURATION AR, 237-0240 POWER TRAIN AR
S/N N1A1-3212
PART OF 334-0419 AXLE AR-FIXED & OSCILLATING, 334-0422, 334-0423, 334-0428, 334-0429, 334-0430 CONFIGURATION AR, 237-0240 POWER TRAIN AR
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 112-0757 Y | [2] | BRAKE & PLANETARY GP | ||
| 137-1392 Y | [1] | DIFFERENTIAL GP | ||
| 112-0738 Y | [1] | GEAR GP-BEVEL & PINION | ||
| 214-6156 Y | [1] | HOUSING GP-FIXED AXLE | ||
| 220-7925 | [1] | PLATE GP-AXLE IDENTIFICATION | ||
| 220-3773 | [1] | PLATE GP-AXLE IDENTIFICATION | ||
| 109-8895 | [1] | PLATE-IDENTIFICATION (LOGGING SKID) | ||
| 220-3681 | [1] | TAPE | ||
| 220-7924 | [1] | PLATE GP-AXLE IDENTIFICATION | ||
| 082-2817 | [4] | TACK | ||
| 109-8895 | [1] | PLATE-IDENTIFICATION (LOGGING SKID) | ||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP38450455
214-9402: AXLE AR-FIXED
214-9402 AXLE AR-FIXED -FRONT, LIMITED SLIP DIFFERENTIAL
S/N N1A1-UP
PART OF 334-0425, 334-0432 CONFIGURATION AR
S/N N1A1-UP
PART OF 334-0425, 334-0432 CONFIGURATION AR
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS#SEBP38450456
334-0419: AXLE AR-FIXED & OSCILLATING
334-0419 AXLE AR-FIXED & OSCILLATING -STANDARD
S/N N1A1-UP
CANNOT BE USED WITH 243-1946 CONTROL GP-ELECTROHYDRAULIC, 319-8253 CONTROL GP-ELECTROHYDRAULIC, 325-2745 CONTROL AR-HIGH LIFT, 339-1894 OPTION AR-POWER TRAIN
S/N N1A1-UP
CANNOT BE USED WITH 243-1946 CONTROL GP-ELECTROHYDRAULIC, 319-8253 CONTROL GP-ELECTROHYDRAULIC, 325-2745 CONTROL AR-HIGH LIFT, 339-1894 OPTION AR-POWER TRAIN
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| Y | [1] | AXLE AR-FIXED (FRONT, STANDARD DIFFERENTIAL) | ||
| Y | [1] | AXLE AR-OSCILLATING (REAR, STANDARD DIFFERENTIAL) | ||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP38450457
112-0723: AXLE AR-OSCILLATING
112-0723 AXLE AR-OSCILLATING -REAR, STANDARD DIFFERENTIAL
S/N N1A1-3212
PART OF 334-0419 AXLE AR-FIXED & OSCILLATING, 334-0428 CONFIGURATION AR, 237-0240 POWER TRAIN AR
S/N N1A1-3212
PART OF 334-0419 AXLE AR-FIXED & OSCILLATING, 334-0428 CONFIGURATION AR, 237-0240 POWER TRAIN AR
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS#SEBP38450458
126-7845: AXLE AR-OSCILLATING
126-7845 AXLE AR-OSCILLATING -REAR, LIMITED SLIP DIFFERENTIAL
S/N N1A1-UP
PART OF 334-0422, 334-0423, 334-0425, 334-0429, 334-0430, 334-0432 CONFIGURATION AR
S/N N1A1-UP
PART OF 334-0422, 334-0423, 334-0425, 334-0429, 334-0430, 334-0432 CONFIGURATION AR
Parts for your 950H WHEEL LOADER:
CATERPILLAR SIS#SEBP38450459
126-7846: AXLE AR-OSCILLATING
126-7846 AXLE AR-OSCILLATING -REAR, NOSPIN DIFFERENTIAL
S/N N1A1-UP
S/N N1A1-UP
Parts for your 950H WHEEL LOADER:
CATERPILLAR SISInformation:
ELECTRICAL AND STARTING SYSTEM
WIRING GP
Special Instruction
Tool Operating Manual
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Reuse And Salvage Guidelines
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Troubleshooting
CID 0100 FMI 04 Engine Oil Pressure short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0110 FMI 04 Engine Coolant Temperature short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0164 FMI 03 Injector Actuation Pressure voltage high
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0091 FMI 02 Incorrect Throttle Switch inputs
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0617 FMI 05 Air Inlet Heater Relay open/current below normal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0164 FMI 04 Injector Actuation Pressure voltage low
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0100 FMI 10 Engine Oil Pressure Sensor abnormal rate of change
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 1785 FMI 03 Intake Manifold Pressure Sensor voltage high
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 1785 FMI 04 Intake Manifold Pressure Sensor voltage low
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0342 FMI 08 Secondary Engine Speed signal abnormal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0617 FMI 06 Air Inlet Heater Relay grounded/current above norm
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0274 FMI 04 Atmospheric Pressure short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 1785 FMI 10 Intake Manifold Pressure Signal abnormal rate of change
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0190 FMI 08 Engine Speed signal abnormal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
Fuel Filter Differential Pressure Switch Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0091 FMI 08 Throttle Position signal abnormal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
Engine Pressure Sensor Open or Short Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0324 FMI 06 Warning Lamp short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 0324 FMI 05 Warning Lamp open/short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 1266 FMI 05 Diagnostic Lamp current below normal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
CID 1266 FMI 06 Diagnostic Lamp current above normal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
Digital Sensor Supply Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
Coolant Level Sensor Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
Engine Shutdown Switch Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
Throttle Position Sensor Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer


