318-5148 GENERATOR AR 60-HERTZ. 480-VOLT AN ATTACHMENT 3508B MARINE AUXILIARY

Parts for your 3508B MARINE AUXILIARY:

Part No	Qty	Parts name
318-5147 Y	[1]	GENERATOR GP

171-6719	[1]	KIT-PARTS (GENERATOR)
		(INCLUDES END STOP, DIVIDERS, TERMINAL BLOCKS, JUMPERS, TOOL, FUSES & PLUGS)

1W-7848	[1]	PLATE-SERIAL NUMBER (ENGLISH)
		S/N 6SN1-UP
		CONTACT YOUR LOCAL DEALER.
		INSTALL ON RH SIDE OF GENERATOR BARREL AT FRONT USING 2K-3219 DRIVE SCREWS TO INSTALL.
2K-3219	[2]	SCREW-DRIVE (NO 6X0.25-IN)
		S/N 6SN1-UP
3N-8764	[1]	FILM-CONNECTION (SPACE HEATER)
		S/N 6SN1-UP
		INSTALL INSIDE OF GENERATOR HOUSING ON PANEL NEXT TO SPACE HEATER TERMINAL STRIP.
106-8061	[1]	PLATE-GENERATOR (GREASE BEARING)
		S/N 6SN1-UP
		INSTALL ON GENERATOR FRONT PANEL ASSEMBLY ON RH SIDE OF PACKAGE, NEXT TO GENERATOR INFORMATION PLATE.
		(GENERATOR)
		S/N 6SN1-UP
		INSTALL FILM ON THE RH SIDE OF THE GENERATOR BARREL, CENTERED FROM FRONT TO BACK, APPROX. 100MM DOWN FROM THE CENTER LINE AT THE TOP OF THE GENERATOR.
		INSTALL FILM ON THE BARREL COVER IF AVAILABLE.
		INSTALL CLEAR LAMINATE OVER FILM.
225-3224	[2]	FILM-WARNING (AUTOMATIC ENGINE START)
		S/N 6SN1-UP
		INSTALL ONE FILM ON THE RH AND LH SIDES OF THE GENERATOR TERMINAL BOX, CENTERED DIRECTLY BELOW THE SHOCK WARNING LABEL.
225-3227	[2]	FILM-WARNING (HOT SURFACE)
		S/N 6SN1-UP
		INSTALL ONE FILM ON EACH SIDE OF THE GENERATOR BARREL, DIRECTLY ON THE GENERATOR BARREL, NOT ON THE BARREL COVER.
		IF THERE IS NO BARREL COVER, CENTER FILMS ON EACH SIDE THE BARREL FROM FRONT TO REAR, AND ON THE RH SIDE, CENTER FILM BELOW THE 118-8452 GLPS GENERATOR INFO FILM.
228-4798	[2]	FILM-IDENTIFICATION (GROUND)
		S/N 6SN1-UP
		INSTALL NEAR GENERATOR GROUND BOLT OR GENERATOR GROUND CUSTOMER CONNECTION POINT.
229-5047	[2]	FILM-WARNING (SHOCK HAZARD, READ OMM)
		S/N 6SN1-UP
		INSTALL ONE FILM ON THE RH AND LH SIDES OF THE GENERATOR TERMINAL BOX, CENTERED DIRECTLY BELOW THE CAT POWER EDGE LABEL.
303-3428	[1]	FILM-IDENTIFICATION (CAT)
		S/N 6SN1-UP
		INSTALL FILM ON THE REAR PANEL OF THE GENERATOR TERMINAL BOX, CENTERED AT THE TOP OF THE REAR PANEL.
303-3440	[2]	FILM-IDENTIFICATION (CAT)
		S/N 6SN1-UP
		INSTALL ONE FILM ON THE RH & LH SIDE OF THE GENERATOR TERMINAL BOX, AT THE TOP LH CORNER OF THE TERMINAL BOX. ALIGN EACH FILM WITH THE EDGES OF THE TERMINAL BOX COVER.
3N-3790	[1]	PLATE-SERIAL NUMBER (ENGINE)
		S/N S2A1-UP; S2B1-UP
		CONTACT YOUR LOCAL DEALER.
		REFLATTEN AFTER STAMPING.
		INSTALL ON LH SIDE OF BLOCK NEAR REAR FACE ON CAMSHAFT COMPARTMENT USING 7B-3028 DRIVE SCREWS.
		STAMP SERIAL NUMBER IN BLOCK JUST BELOW PLATE IN FIGURES 6 HIGH.
7B-3028	[2]	SCREW-DRIVE (NO 4X 3/16-IN)
		S/N S2A1-UP; S2B1-UP
5P-1175	[1]	FILM-IDENTIFICATION (ENGINE OIL FILL)
		S/N S2A1-UP; S2B1-UP
		INSTALL FILM ON THE TOP OF THE OIL FILL CAP CENTERED BETWEEN THE HANDLE AND THE TOP EDGE OF THE OIL FILL CAP.
115-5852	[1]	PLATE & FILM GP (ENGINE INFORMATION)
		S/N S2A1-UP; S2B1-UP
		CONTACT YOUR LOCAL DEALER.
		INSTALL FILM ON THE LH, FRONT, LOWER HEAD FACE OF THE BLOCK BETWEEN CYL. #2 AND THE FRONT HOUSING, READABLE FROM THE REAR OF ENGINE.
		INSTALL CLEAR LAMINATE OVER FILM.
233-6084	[2]	FILM-WARNING (FIRE, STOP ENGINE, DO NOT OPEN)
		S/N S2A1-UP; S2B1-UP
		INSTALL ONE FILM ON THE RH & LH SIDES OF THE ENGINE ON THE FIRST VISIBLE CRANKCASE COVER NEAREST THE CENTERLINE OF THE ENGINE VISIBLE FROM THE SIDE OF THE ENGINE. DO NOT INSTALL ON THE EXPLOSION RELIEF VALVES.
250-3444	[1]	FILM-INFORMATION (STANDARD ROTATION)
		S/N S2A1-UP; S2B1-UP
		INSTALL FILM ON THE LH CAM GEAR COVER IN A VISIBLE LOCATION. IF THAT COVER IS NOT AVAILABLE MOVE TO THE RH CAM GEAR COVER.
298-5631	[2]	PLATE-IDENTIFICATION (CAT)
		S/N S2A1-UP; S2B1-UP
		INSTALL ONE PLATE ON THE RH REAR CAM COVER AND ONE ON THE LH FRONT CAM COVER VISIBLE FROM THE SIDE OF THE ENGINE.
		IF THESE LOCATIONS ARE NOT VISIBLE, MOVE PLATES TO THE FIRST AVAILABLE CAM COVER VISIBLE FROM THE SIDE OF THE ENGINE.
308-4479	[2]	FILM-WARNING (NO WELD, READ OMM)
		S/N S2A1-UP; S2B1-UP
		INSTALL ONE FILM ON EACH SIDE OF THE ENGINE, ONE FILM ON THE POWER DISTRIBUTION BOX VISIBLE FROM THE RIGHT SIDE OF THE ENGINE, AND ONE FILM ON THE OPPOSITE SIDE OF THE ENGINE, CENTERED ON THE FIRST VISIBLE SIDE COVER FORM THE REAR OF THE ENGINE.
		IF THERE IS NOT POWER DISTRIBUTION BOX, INSTALL BOTH FILMS ON THE FIRST VISIBLE SIDE COVER FROM THE REAR.
455-6769	[1]	FILM-IDENTIFICATION (ENGINE OIL FILL)
		S/N S2A1-UP; S2B1-UP
		INSTALL FILM AT THE BASE OF THE DIPSTICK ON THE FLANGE.
Y		SEPARATE ILLUSTRATION