POWER TRAIN
AXLE GPPOWER TRAIN
AXLE GP
#SEBP42230160
241-7444: AXLE & MTG AR-REAR
241-7444 AXLE & MTG AR-REAR -WIDE
S/N BDX2001-99999
PART OF 241-7442 AXLE AR-WIDE
AN ATTACHMENT
S/N BDX2001-99999
PART OF 241-7442 AXLE AR-WIDE
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 5W-0965 | [20] | RING | |
| 2. | 8T-4123 | [16] | WASHER (22X35X3.5-MM THK) | |
| 3. | 8U-5923 | [2] | FITTING AS | |
| 4. | 303-9446 | [20] | LOCKWASHER | |
| 5. | 5W-1386 M | [20] | NUT (M22X1.5-THD) | |
| 6. | 237-4535 Y | [1] | AXLE & TRANSMISSION AR | |
| 7. | 241-6199 | [1] | ELBOW AS | |
| 6V-8398 | [1] | SEAL-O-RING | ||
| 8T-6850 | [1] | SEAL-O-RING | ||
| 241-6192 | [1] | ELBOW | ||
| 8. | 4I-6766 M | [8] | BOLT (M20X2.5X230-MM) | |
| 9. | 6V-6560 | [2] | SEAL-O-RING | |
| 10. | 188-2720 M | [8] | LOCKNUT (M20X2.5-THD) | |
| 11. | 6V-8398 | [3] | SEAL-O-RING | |
| 12. | 8T-6850 | [1] | SEAL-O-RING | |
| 13. | 8T-7488 | [1] | CONNECTOR | |
| 14. | 244-3269 I | [1] | HOSE AS | |
| 15. | 1C-9934 I | [1] | HOSE AS | |
| I | REFER TO HYDRAULIC INFORMATION SYSTEM | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP42230161
175-6559: AXLE & TRANSMISSION AR
175-6559 AXLE & TRANSMISSION AR
S/N BDX2001-99999
PART OF 194-9207 AXLE AR-REAR
AN ATTACHMENT
S/N BDX2001-99999
PART OF 194-9207 AXLE AR-REAR
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS#SEBP42230162
175-6562: AXLE & TRANSMISSION AR
175-6562 AXLE & TRANSMISSION AR -WIDE AXLE
S/N BDX2001-99999
PART OF 188-4935 AXLE AR-REAR
AN ATTACHMENT
S/N BDX2001-99999
PART OF 188-4935 AXLE AR-REAR
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS#SEBP42230163
237-4525: AXLE & TRANSMISSION AR
237-4525 AXLE & TRANSMISSION AR
S/N BDX2001-99999
PART OF 241-7436 AXLE & MTG AR-REAR
S/N BDX2001-99999
PART OF 241-7436 AXLE & MTG AR-REAR
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 237-4526 Y | [1] | TRANSMISSION GP (DIRECT DRIVE) | |
| 2. | 233-8734 | [2] | HOUSING-AXLE | |
| 3. | 233-8737 | [2] | SHAFT-AXLE | |
| 4. | 233-8738 | [1] | HOUSING | |
| 5. | 054-6514 B | [2] | SHIM (0.1-MM THK) | |
| 121-7679 B | [2] | SHIM (0.15-MM THK) | ||
| 054-6513 B | [2] | SHIM (0.2-MM THK) | ||
| 121-7680 B | [2] | SHIM (0.25-MM THK) | ||
| 054-6512 B | [2] | SHIM (0.3-MM THK) | ||
| 128-7675 B | [2] | SHIM (0.35-MM THK) | ||
| 7T-0564 B | [2] | SHIM (0.4-MM THK) | ||
| 121-7677 B | [2] | SHIM (0.45-MM THK) | ||
| 7T-0563 B | [2] | SHIM (0.5-MM THK) | ||
| 121-7678 B | [2] | SHIM (0.55-MM THK) | ||
| 7T-0562 B | [2] | SHIM (0.6-MM THK) | ||
| 128-7676 B | [2] | SHIM (0.65-MM THK) | ||
| 128-7677 B | [2] | SHIM (0.7-MM THK) | ||
| 128-7680 B | [2] | SHIM (0.75-MM THK) | ||
| 7T-0561 B | [2] | SHIM (0.8-MM THK) | ||
| 128-7681 B | [2] | SHIM (0.85-MM THK) | ||
| 128-7683 B | [2] | SHIM (0.9-MM THK) | ||
| 128-7684 B | [2] | SHIM (0.95-MM THK) | ||
| 7T-0560 B | [2] | SHIM (1-MM THK) | ||
| 128-7685 B | [2] | SHIM (1.05-MM THK) | ||
| 128-7686 B | [2] | SHIM (1.1-MM THK) | ||
| 128-7687 B | [2] | SHIM (1.15-MM THK) | ||
| 128-7688 B | [2] | SHIM (1.25-MM THK) | ||
| 128-7689 B | [2] | SHIM (1.3-MM THK) | ||
| 128-7690 B | [2] | SHIM (1.35-MM THK) | ||
| 7T-0558 B | [2] | SHIM (1.4-MM THK) | ||
| 128-7691 B | [2] | SHIM (1.45-MM THK) | ||
| 128-7692 B | [2] | SHIM (1.5-MM THK) | ||
| 128-7693 B | [2] | SHIM (1.55-MM THK) | ||
| 128-7694 B | [2] | SHIM (1.6-MM THK) | ||
| 128-7695 B | [2] | SHIM (1.65-MM THK) | ||
| 7T-0552 B | [2] | SHIM (2-MM THK) | ||
| 202-8137 B | [2] | SHIM (1.47-MM THK) | ||
| 202-8138 B | [2] | SHIM (1.63-MM THK) | ||
| 202-8139 B | [2] | SHIM (1.75-MM THK) | ||
| 202-8140 B | [2] | SHIM (1.7-MM THK) | ||
| 202-8141 B | [2] | SHIM (1.8-MM THK) | ||
| 202-8142 B | [2] | SHIM (1.85-MM THK) | ||
| 202-8143 B | [2] | SHIM (1.9-MM THK) | ||
| 202-8144 B | [2] | SHIM (1.95-MM THK) | ||
| 45. | 9R-7003 | [1] | BEARING-TAPERED ROLLER | |
| 46. | 6Y-2942 | [1] | BEARING-TAPERED ROLLER | |
| 47. | 6Y-2943 | [1] | CUP-BEARING (TAPERED ROLLER) | |
| 48. | 8U-6079 | [2] | SEAL-O-RING | |
| 49. | 238-4666 M | [32] | BOLT (M18X2.5X65-MM) | |
| 50. | 5W-5531 | [32] | WASHER (19X30X3-MM THK) | |
| 51. | 263-3629 | [3] | PLUG AS | |
| 52. | 203-0215 | [4] | SEAL-O-RING | |
| 53. | 263-3630 | [1] | PLUG AS-MAGNET | |
| 54. | 8T-4183 M | [4] | BOLT (M12X1.75X40-MM) | |
| 55. | 9X-0690 | [10] | NUT | |
| 56. | 233-8728 | [1] | GEAR-CROWN | |
| 57. | 9R-6991 | [1] | CASE-DIFFERENTIAL | |
| 58. | 9R-6964 | [2] | GEAR-DIFFERENTIAL | |
| 59. | 6T-5749 | [2] | WASHER-THRUST | |
| 60. | 128-7855 | [4] | GEAR-PINION | |
| 61. | 9R-6994 | [4] | WASHER-THRUST | |
| 62. | 119-9288 | [2] | SHAFT | |
| 63. | 9R-6818 M | [12] | BOLT (M12X1.5X125-MM) | |
| 64. | 9R-6819 | [12] | WASHER (13X21.9X3-MM THK) | |
| 65. | 8T-2450 | [4] | PIN-SPRING | |
| 66. | 9R-6962 | [4] | PIN-CLAMPING | |
| 67. | 233-8739 | [2] | HUB GP-WHEEL | |
| (EACH INCLUDES) | ||||
| 243-0378 | [1] | NUT | ||
| 68. | 8T-0088 M | [28] | BOLT (M16X2X65-MM) | |
| 69. | 8D-5054 | [28] | WASHER-HARD (17X30X3-MM THK) | |
| 70. | 8U-5927 | [2] | SEAL-O-RING | |
| 71. | 233-8742 | [2] | GEAR-SUN | |
| 72. | 5W-5682 | [2] | VALVE AS-PURGE (AXLE) | |
| 74. | 263-4057 | [8] | DOWEL | |
| 75. | 203-5417 | [2] | SEAL-LIP TYPE | |
| 76. | 121-8167 | [4] | BEARING-ROLLER | |
| 77. | 238-3298 | [2] | SLEEVE-SPACER | |
| 78. | 263-3700 | [2] | HUB | |
| 79. | 110-4745 | [2] | SEAL-O-RING | |
| 80. | 263-3701 | [2] | GEAR-CARRIER | |
| 81. | 8U-2359 | [4] | SEAL-O-RING | |
| 82. | 8U-2058 | [2] | SEAL-O-RING | |
| 83. | 263-3702 | [2] | GEAR-INTERNAL | |
| 84. | 263-3703 | [2] | PISTON | |
| 85. | 8U-2373 | [2] | SEAL | |
| 86. | 238-3303 | [2] | RING (2-MM THK) | |
| 87. | 8U-0754 | [2] | SEAL | |
| 88. | 238-3304 | [2] | RING (2-MM THK) | |
| 89. | 8U-3592 | [16] | SPRING | |
| 90. | 238-3305 | [16] | SPRING | |
| 91. | 8T-0275 M | [16] | BOLT (M6X1X50-MM) | |
| 92. | 8U-3591 | [16] | SPACER (6.5X15X7-MM THK) | |
| 93. | 263-3704 | [12] | DISC-CLUTCH (4.5-MM THK) | |
| 94. | 238-3307 | [12] | DISC-CLUTCH (2-MM THK) | |
| 238-3308 B | [12] | DISC-CLUTCH (3-MM THK) | ||
| 238-3309 B | [12] | DISC-CLUTCH (2.5-MM THK) | ||
| 97. | 110-0165 B | [2] | WASHER-THRUST (1.5-MM THK) | |
| 110-0164 B | [2] | WASHER-THRUST (1.7-MM THK) | ||
| 110-0163 B | [2] | WASHER-THRUST (2-MM THK) | ||
| 110-0162 B | [2] | WASHER-THRUST (2.2-MM THK) | ||
| 110-0161 B | [2] | WASHER-THRUST (2.5-MM THK) | ||
| 110-0160 B | [2] | WASHER-THRUST (2.7-MM THK) | ||
| 110-0159 B | [2] | WASHER-THRUST (3-MM THK) | ||
| 104. | 238-3310 | [2] | HOUSING | |
| 105. | 238-3311 | [6] | GEAR-PLANETARY | |
| 106. | 213-9783 | [6] | BEARING-ROLLER | |
| 107. | 190-8590 | [12] | RING-SNAP | |
| 108. | 190-8591 | [12] | WASHER (64.5X72.1X2-MM THK) | |
| 109. | 110-4737 | [6] | RING-RETAINING | |
| 110. | 5W-2177 M | [4] | BOLT-SOCKET HEAD (M12X1.75X20-MM) | |
| 111. | 9R-3168 M | [2] | SCREW (M10X1.5X20-MM) | |
| 112. | 238-3312 | [20] | STUD-WHEEL | |
| B | USE AS REQUIRED | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP42230164
237-4535: AXLE & TRANSMISSION AR
237-4535 AXLE & TRANSMISSION AR
S/N BDX2001-99999
PART OF 241-7444 AXLE & MTG AR-REAR
AN ATTACHMENT
S/N BDX2001-99999
PART OF 241-7444 AXLE & MTG AR-REAR
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 237-4526 Y | [1] | TRANSMISSION GP (DIRECT DRIVE) | |
| 2. | 238-3313 | [2] | HOUSING-AXLE | |
| 3. | 238-3314 | [2] | SHAFT-AXLE | |
| 4. | 233-8738 | [1] | HOUSING | |
| 5. | 054-6514 B | [2] | SHIM (0.1-MM THK) | |
| 121-7679 B | [2] | SHIM (0.15-MM THK) | ||
| 054-6513 B | [2] | SHIM (0.2-MM THK) | ||
| 121-7680 B | [2] | SHIM (0.25-MM THK) | ||
| 054-6512 B | [2] | SHIM (0.3-MM THK) | ||
| 128-7675 B | [2] | SHIM (0.35-MM THK) | ||
| 7T-0564 B | [2] | SHIM (0.4-MM THK) | ||
| 121-7677 B | [2] | SHIM (0.45-MM THK) | ||
| 7T-0563 B | [2] | SHIM (0.5-MM THK) | ||
| 121-7678 B | [2] | SHIM (0.55-MM THK) | ||
| 7T-0562 B | [2] | SHIM (0.6-MM THK) | ||
| 128-7676 B | [2] | SHIM (0.65-MM THK) | ||
| 128-7677 B | [2] | SHIM (0.7-MM THK) | ||
| 128-7680 B | [2] | SHIM (0.75-MM THK) | ||
| 7T-0561 B | [2] | SHIM (0.8-MM THK) | ||
| 128-7681 B | [2] | SHIM (0.85-MM THK) | ||
| 128-7683 B | [2] | SHIM (0.9-MM THK) | ||
| 128-7684 B | [2] | SHIM (0.95-MM THK) | ||
| 7T-0560 B | [2] | SHIM (1-MM THK) | ||
| 128-7685 B | [2] | SHIM (1.05-MM THK) | ||
| 128-7686 B | [2] | SHIM (1.1-MM THK) | ||
| 128-7687 B | [2] | SHIM (1.15-MM THK) | ||
| 128-7688 B | [2] | SHIM (1.25-MM THK) | ||
| 128-7689 B | [2] | SHIM (1.3-MM THK) | ||
| 128-7690 B | [2] | SHIM (1.35-MM THK) | ||
| 7T-0558 B | [2] | SHIM (1.4-MM THK) | ||
| 128-7691 B | [2] | SHIM (1.45-MM THK) | ||
| 128-7692 B | [2] | SHIM (1.5-MM THK) | ||
| 128-7693 B | [2] | SHIM (1.55-MM THK) | ||
| 128-7694 B | [2] | SHIM (1.6-MM THK) | ||
| 128-7695 B | [2] | SHIM (1.65-MM THK) | ||
| 7T-0552 B | [2] | SHIM (2-MM THK) | ||
| 202-8137 B | [2] | SHIM (1.47-MM THK) | ||
| 202-8138 B | [2] | SHIM (1.63-MM THK) | ||
| 202-8139 B | [2] | SHIM (1.75-MM THK) | ||
| 202-8140 B | [2] | SHIM (1.7-MM THK) | ||
| 202-8141 B | [2] | SHIM (1.8-MM THK) | ||
| 202-8142 B | [2] | SHIM (1.85-MM THK) | ||
| 202-8143 B | [2] | SHIM (1.9-MM THK) | ||
| 202-8144 B | [2] | SHIM (1.95-MM THK) | ||
| 45. | 9R-7003 | [1] | BEARING-TAPERED ROLLER | |
| 46. | 6Y-2942 | [1] | BEARING-TAPERED ROLLER | |
| 47. | 6Y-2943 | [1] | CUP-BEARING (TAPERED ROLLER) | |
| 48. | 8U-6079 | [2] | SEAL-O-RING | |
| 49. | 238-4666 M | [32] | BOLT (M18X2.5X65-MM) | |
| 50. | 5W-5531 | [32] | WASHER (19X30X3-MM THK) | |
| 51. | 263-3629 | [3] | PLUG AS | |
| 52. | 203-0215 | [4] | SEAL-O-RING | |
| 53. | 263-3630 | [1] | PLUG AS-MAGNET | |
| 54. | 8T-4183 M | [4] | BOLT (M12X1.75X40-MM) | |
| 55. | 9X-0690 | [10] | NUT | |
| 56. | 233-8728 | [1] | GEAR-CROWN | |
| 57. | 9R-6991 | [1] | CASE-DIFFERENTIAL | |
| 58. | 9R-6964 | [2] | GEAR-DIFFERENTIAL | |
| 59. | 6T-5749 | [2] | WASHER-THRUST | |
| 60. | 128-7855 | [4] | GEAR-PINION | |
| 61. | 9R-6994 | [4] | WASHER-THRUST | |
| 62. | 119-9288 | [2] | SHAFT | |
| 63. | 9R-6818 M | [12] | BOLT (M12X1.5X125-MM) | |
| 64. | 9R-6819 | [12] | WASHER (13X21.9X3-MM THK) | |
| 65. | 8T-2450 | [4] | PIN-SPRING | |
| 66. | 9R-6962 | [4] | PIN-CLAMPING | |
| 67. | 233-8739 | [2] | HUB GP-WHEEL | |
| (EACH INCLUDES) | ||||
| 67A. | 243-0378 | [1] | NUT | |
| 68. | 8T-0088 M | [28] | BOLT (M16X2X65-MM) | |
| 69. | 8D-5054 | [28] | WASHER-HARD (17X30X3-MM THK) | |
| 70. | 8U-5927 | [2] | SEAL-O-RING | |
| 71. | 233-8742 | [2] | GEAR-SUN | |
| 72. | 5W-5682 | [2] | VALVE AS-PURGE (AXLE) | |
| 73. | 263-4057 | [8] | DOWEL | |
| 75. | 203-5417 | [2] | SEAL-LIP TYPE | |
| 76. | 121-8167 | [4] | BEARING-ROLLER | |
| 77. | 238-3298 | [2] | SLEEVE-SPACER | |
| 78. | 263-3700 | [2] | HUB | |
| 79. | 110-4745 | [2] | SEAL-O-RING | |
| 80. | 263-3701 | [2] | GEAR-CARRIER | |
| 81. | 8U-2359 | [4] | SEAL-O-RING | |
| 82. | 8U-2058 | [2] | SEAL-O-RING | |
| 83. | 263-3702 | [2] | GEAR-INTERNAL | |
| 84. | 263-3703 | [2] | PISTON | |
| 85. | 8U-2373 | [2] | SEAL | |
| 86. | 238-3303 | [2] | RING (2-MM THK) | |
| 87. | 8U-0754 | [2] | SEAL | |
| 88. | 238-3304 | [2] | RING (2-MM THK) | |
| 89. | 8U-3592 | [16] | SPRING | |
| 90. | 238-3305 | [16] | SPRING | |
| 91. | 8T-0275 M | [16] | BOLT (M6X1X50-MM) | |
| 92. | 8U-3591 | [16] | SPACER (6.5X15X7-MM THK) | |
| 93. | 263-3704 | [12] | DISC-CLUTCH (4.5-MM THK) | |
| 94. | 238-3307 B | [12] | DISC-CLUTCH (2-MM THK) | |
| 238-3308 B | [12] | DISC-CLUTCH (3-MM THK) | ||
| 238-3309 B | [12] | DISC-CLUTCH (2.5-MM THK) | ||
| 97. | 110-0165 B | [2] | WASHER-THRUST (1.5-MM THK) | |
| 110-0164 B | [2] | WASHER-THRUST (1.7-MM THK) | ||
| 110-0163 B | [2] | WASHER-THRUST (2-MM THK) | ||
| 110-0162 B | [2] | WASHER-THRUST (2.2-MM THK) | ||
| 110-0161 B | [2] | WASHER-THRUST (2.5-MM THK) | ||
| 110-0160 B | [2] | WASHER-THRUST (2.7-MM THK) | ||
| 110-0159 B | [2] | WASHER-THRUST (3-MM THK) | ||
| 104. | 238-3310 | [2] | HOUSING | |
| 105. | 238-3311 | [6] | GEAR-PLANETARY | |
| 106. | 213-9783 | [6] | BEARING-ROLLER | |
| 107. | 190-8590 | [12] | RING-SNAP | |
| 108. | 190-8591 | [12] | WASHER (64.5X72.1X2-MM THK) | |
| 109. | 110-4737 | [6] | RING-RETAINING | |
| 110. | 5W-2177 M | [4] | BOLT-SOCKET HEAD (M12X1.75X20-MM) | |
| 111. | 9R-3168 M | [2] | SCREW (M10X1.5X20-MM) | |
| 112. | 238-3312 | [20] | STUD-WHEEL | |
| B | USE AS REQUIRED | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP42230165
121-4435: AXLE AR-FRONT
121-4435 AXLE AR-FRONT
S/N BDX2001-99999
PART OF 118-1879 AXLE & MTG AR-FRONT
AN ATTACHMENT
S/N BDX2001-99999
PART OF 118-1879 AXLE & MTG AR-FRONT
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 121-7622 | [1] | GEAR AS-PINION | |
| 2. | 9R-6814 B | [1] | WASHER (88X104.6X1.5-MM THK) | |
| 9R-6805 B | [1] | WASHER (88X104.6X0.9-MM THK) | ||
| 9R-6806 B | [1] | WASHER (88X104.6X0.95-MM THK) | ||
| 9R-6807 B | [1] | WASHER (88X104.6X1-MM THK) | ||
| 9R-6808 B | [1] | WASHER (88X104.6X1.05-MM THK) | ||
| 9R-6809 B | [1] | WASHER (88X104.6X1.1-MM THK) | ||
| 9R-6810 B | [1] | WASHER (88X104.6X1.15-MM THK) | ||
| 9R-6811 B | [1] | WASHER (88X104.6X1.2-MM THK) | ||
| 9R-6812 B | [1] | WASHER (88X104.6X1.25-MM THK) | ||
| 9R-6813 B | [1] | WASHER (88X104.6X1.3-MM THK) | ||
| 9R-6801 B | [1] | WASHER (88X104.6X0.7-MM THK) | ||
| 9R-6802 B | [1] | WASHER (88X104.6X0.75-MM THK) | ||
| 9R-6803 B | [1] | WASHER (88X104.6X0.8-MM THK) | ||
| 9R-6804 B | [1] | WASHER (88X104.6X0.85-MM THK) | ||
| 3. | 203-0214 | [1] | SEAL-O-RING | |
| 4. | 220-2593 | [2] | BUSHING-SLEEVE | |
| 5. | 128-7901 | [1] | ELBOW AS | |
| 6. | 8U-2354 B | [2] | SHIM (6-MM THK) | |
| 5W-6405 B | [2] | SHIM (6.5-MM THK) | ||
| 5W-7644 B | [2] | SHIM (4-MM THK) | ||
| 5W-7642 B | [2] | SHIM (5-MM THK) | ||
| 5W-7641 B | [2] | SHIM (5.5-MM THK) | ||
| 5W-7643 B | [2] | SHIM (4.5-MM THK) | ||
| 128-1733 B | [2] | SHIM (2-MM THK) | ||
| 128-1734 B | [2] | SHIM (3-MM THK) | ||
| 5W-6408 B | [2] | WASHER (18.5X35X8-MM THK) | ||
| 202-8145 B | [2] | WASHER (18.5X35X9-MM THK) | ||
| 202-8146 B | [2] | WASHER (18.5X35X11-MM THK) | ||
| 202-8147 B | [2] | WASHER (18.5X35X12-MM THK) | ||
| 202-8148 B | [2] | WASHER (18.5X35X13-MM THK) | ||
| 202-8149 B | [2] | WASHER (18.5X35X14-MM THK) | ||
| 7. | 121-7686 | [2] | RING | |
| 8. | 121-7687 | [2] | SEAL-O-RING | |
| 9. | 8U-3473 | [1] | SEAL-O-RING | |
| 10. | 8U-5818 | [1] | FITTING | |
| 11. | 5W-5632 | [4] | BOLT (M14X2X100-MM) | |
| 12. | 5W-6442 | [1] | HOUSING | |
| 13. | 5W-5547 B | [1] | DISC (1-MM THK) | |
| 5W-5548 B | [1] | DISC (1.1-MM THK) | ||
| 5W-5549 B | [1] | DISC (1.2-MM THK) | ||
| 5W-5550 B | [1] | DISC (1.3-MM THK) | ||
| 5W-5551 B | [1] | DISC (1.4-MM THK) | ||
| 5W-5552 B | [1] | DISC (1.5-MM THK) | ||
| 5W-5553 B | [1] | DISC (1.6-MM THK) | ||
| 5W-5554 B | [1] | DISC (1.7-MM THK) | ||
| 5W-6400 B | [1] | DISC (1.8-MM THK) | ||
| 5W-5555 B | [1] | DISC (1.05-MM THK) | ||
| 5W-5556 B | [1] | DISC (1.15-MM THK) | ||
| 5W-5561 B | [1] | DISC (1.65-MM THK) | ||
| 8U-2752 B | [1] | DISC (0.7-MM THK) | ||
| 8U-2753 B | [1] | DISC (0.8-MM THK) | ||
| 8U-2754 B | [1] | DISC (0.9-MM THK) | ||
| 14. | 5W-6391 | [2] | SCRAPER | |
| 15. | 5W-5646 | [1] | SEAL | |
| 16. | 7T-9342 | [1] | CONE-BEARING | |
| 17. | 9R-6932 B | [1] | RING (11.3-MM THK) | |
| 9R-6933 B | [1] | RING (11.33-MM THK) | ||
| 9R-6934 B | [1] | RING (11.36-MM THK) | ||
| 9R-6935 B | [1] | RING (11.39-MM THK) | ||
| 9R-6936 B | [1] | RING (11.42-MM THK) | ||
| 9R-6937 B | [1] | RING (11.45-MM THK) | ||
| 9R-6938 B | [1] | RING (11.48-MM THK) | ||
| 9R-6939 B | [1] | RING (11.51-MM THK) | ||
| 9R-6940 B | [1] | RING (11.54-MM THK) | ||
| 9R-6941 B | [1] | RING (11.57-MM THK) | ||
| 9R-6942 B | [1] | RING (11.6-MM THK) | ||
| 9R-6943 B | [1] | RING (11.63-MM THK) | ||
| 9R-6944 B | [1] | RING (11.66-MM THK) | ||
| 9R-6945 B | [1] | RING (11.69-MM THK) | ||
| 9R-6836 B | [1] | RING (11.72-MM THK) | ||
| 9R-6837 B | [1] | RING (11.75-MM THK) | ||
| 9R-6838 B | [1] | RING (11.78-MM THK) | ||
| 9R-6839 B | [1] | RING (11.81-MM THK) | ||
| 9R-6840 B | [1] | RING (11.84-MM THK) | ||
| 9R-6841 B | [1] | RING (11.87-MM THK) | ||
| 9R-6842 B | [1] | RING (11.9-MM THK) | ||
| 9R-6843 B | [1] | RING (11.93-MM THK) | ||
| 9R-6844 B | [1] | RING (11.96-MM THK) | ||
| 9R-6845 B | [1] | RING (11.99-MM THK) | ||
| 9R-6846 B | [1] | RING (12.02-MM THK) | ||
| 9R-6847 B | [1] | RING (12.05-MM THK) | ||
| 9R-6848 B | [1] | RING (12.08-MM THK) | ||
| 9R-6849 B | [1] | RING (12.11-MM THK) | ||
| 9R-6850 B | [1] | RING (12.14-MM THK) | ||
| 9R-6924 B | [1] | RING (12.17-MM THK) | ||
| 9R-6925 B | [1] | RING (12.2-MM THK) | ||
| 9R-6926 B | [1] | RING (12.23-MM THK) | ||
| 9R-6927 B | [1] | RING (12.26-MM THK) | ||
| 9R-6928 B | [1] | RING (12.29-MM THK) | ||
| 9R-6929 B | [1] | RING (12.32-MM THK) | ||
| 9R-6930 B | [1] | RING (12.35-MM THK) | ||
| 9R-6931 B | [1] | RING (12.38-MM THK) | ||
| 8U-5669 B | [1] | SPACER (11.27-MM THK) | ||
| 8U-5670 B | [1] | SPACER (11.24-MM THK) | ||
| 8U-5671 B | [1] | SPACER (11.21-MM THK) | ||
| 8U-5672 B | [1] | SPACER (11.18-MM THK) | ||
| 8U-5673 B | [1] | SPACER (11.15-MM THK) | ||
| 128-7637 B | [1] | RING (11.12-MM THK) | ||
| 128-7638 B | [1] | RING (11.09-MM THK) | ||
| 128-7639 B | [1] | RING (11.06-MM THK) | ||
| 128-7640 B | [1] | RING (11.03-MM THK) | ||
| 128-7641 B | [1] | RING (11-MM THK) | ||
| 128-7642 B | [1] | RING (10.97-MM THK) | ||
| 128-7643 B | [1] | RING (10.94-MM THK) | ||
| 18. | 5W-6076 | [1] | BOLT | |
| 19. | 5W-5630 | [1] | PLUG | |
| 20. | 6V-5225 | [4] | SCREW-DRIVE | |
| 21. | 5W-5531 | [16] | WASHER (19X30X3-MM THK) | |
| 22. | 6Y-2942 | [1] | BEARING-TAPERED ROLLER | |
| 6Y-2943 | [1] | CUP-BEARING (TAPERED ROLLER) | ||
| 23. | 5W-5627 M | [16] | BOLT (M18X2.5X60-MM) | |
| 24. | 5W-5475 | [1] | SEAL-O-RING | |
| 25. | 5W-6392 | [2] | SEAL-O-RING | |
| 26. | 5W-5483 | [2] | RING | |
| 27. | 5W-5485 | [1] | SEAL-O-RING | |
| 28. | 5W-6643 | [1] | GUIDE | |
| 29. | 5W-4819 | [2] | SEAL-O-RING | |
| 30. | 5W-5696 | [1] | CYLINDER (STEERING) | |
| 31. | 6T-6408 | [2] | SEAL-O-RING | |
| 32. | 9W-4926 | [2] | PLUG | |
| 33. | 9X-0642 | [20] | NUT | |
| 34. | 5W-5694 | [20] | RING | |
| 35. | 9X-0641 | [20] | WASHER | |
| 36. | 054-7758 | [20] | STUD | |
| 37. | 5W-2177 M | [4] | BOLT-SOCKET HEAD (M12X1.75X20-MM) | |
| 38. | 121-7626 | [2] | PLUG | |
| 39. | 054-6552 B | [2] | SHIM (1.5-MM THK) | |
| 054-6553 B | [2] | SHIM (2-MM THK) | ||
| 054-6554 B | [2] | SHIM (2.5-MM THK) | ||
| 054-6555 B | [2] | SHIM (3-MM THK) | ||
| 054-6556 B | [2] | SHIM (1.7-MM THK) | ||
| 054-6557 B | [2] | SHIM (2.2-MM THK) | ||
| 8U-2751 B | [2] | WASHER-THRUST | ||
| 40. | 8T-2355 | [8] | RING-RETAINING | |
| 41. | 9R-6949 | [16] | RING | |
| 42. | 121-7627 | [8] | BEARING-ROLLER | |
| 43. | 9R-6950 | [8] | PINION-PLANETARY | |
| 44. | 121-7628 | [2] | HOUSING-DRIVE | |
| 45. | 5W-6370 | [2] | RING-RETAINING | |
| 46. | 9R-6958 | [2] | RING-RETAINING | |
| 47. | 219-4548 C | [2] | GEAR-CARRIER (35-TEETH) | |
| 48. | 219-4549 C | [2] | GEAR-SUN | |
| 49. | 8U-0746 | [2] | WASHER-THRUST | |
| 50. | 121-7631 | [2] | RING-RETAINING | |
| 51. | 5W-6404 | [2] | WASHER | |
| 52. | 121-7632 | [10] | DISC-FRICTION | |
| 53. | 121-7635 B | [12] | DISC-GEAR (2-MM THK) | |
| 121-7634 B | [12] | DISC-GEAR (2.5-MM THK) | ||
| 121-7633 B | [12] | DISC-GEAR (3-MM THK) | ||
| 54. | 8U-3591 | [12] | SPACER (6.5X15X7-MM THK) | |
| 55. | 121-7636 M | [12] | BOLT (M6X1X40-MM) | |
| 56. | 8U-3594 | [12] | NUT | |
| 57. | 8U-3592 | [12] | SPRING | |
| 58. | 8U-5698 | [2] | PLATE-WASHER | |
| 59. | 9R-7002 | [1] | BEARING-TAPERED ROLLER | |
| 60. | 9R-6997 | [1] | SEAL | |
| 61. | 5W-5666 | [1] | FLANGE | |
| 62. | 9R-6954 | [1] | PLATE-COVER | |
| 63. | 9R-6985 | [1] | WASHER (27.1X50X5-MM THK) | |
| 64. | 5W-5352 M | [1] | NUT (M27X1.5-THD) | |
| 65. | 5W-5398 | [1] | WASHER-RETAINING | |
| 66. | 121-7625 | [1] | CASE | |
| 67. | 9R-6964 | [2] | GEAR-DIFFERENTIAL | |
| 68. | 6T-5749 | [2] | WASHER-THRUST | |
| 69. | 128-7855 | [4] | GEAR-PINION | |
| 70. | 9R-6994 | [4] | WASHER-THRUST | |
| 71. | 9R-6993 | [1] | SPIDER | |
| 72. | 8T-2323 M | [12] | BOLT-SOCKET HEAD (M12X1.5X120-MM) | |
| 73. | 9R-6819 | [12] | WASHER (13X21.9X3-MM THK) | |
| 74. | 8T-2450 | [4] | PIN-SPRING | |
| 75. | 9R-6962 | [4] | PIN-CLAMPING | |
| 76. | 132-6519 | [1] | HOUSING-AXLE | |
| 77. | 132-6520 | [1] | HOUSING-AXLE | |
| 78. | 054-6514 B | [2] | SHIM (0.1-MM THK) | |
| 121-7679 B | [2] | SHIM (0.15-MM THK) | ||
| 054-6513 B | [2] | SHIM (0.2-MM THK) | ||
| 121-7680 B | [2] | SHIM (0.25-MM THK) | ||
| 054-6512 B | [2] | SHIM (0.3-MM THK) | ||
| 128-7675 B | [2] | SHIM (0.35-MM THK) | ||
| 7T-0564 B | [2] | SHIM (0.4-MM THK) | ||
| 121-7677 B | [2] | SHIM (0.45-MM THK) | ||
| 7T-0563 B | [2] | SHIM (0.5-MM THK) | ||
| 121-7678 B | [2] | SHIM (0.55-MM THK) | ||
| 7T-0562 B | [2] | SHIM (0.6-MM THK) | ||
| 128-7676 B | [2] | SHIM (0.65-MM THK) | ||
| 128-7677 B | [2] | SHIM (0.7-MM THK) | ||
| 128-7680 B | [2] | SHIM (0.75-MM THK) | ||
| 7T-0561 B | [2] | SHIM (0.8-MM THK) | ||
| 128-7681 B | [2] | SHIM (0.85-MM THK) | ||
| 128-7683 B | [2] | SHIM (0.9-MM THK) | ||
| 128-7684 B | [2] | SHIM (0.95-MM THK) | ||
| 7T-0560 B | [2] | SHIM (1-MM THK) | ||
| 128-7685 B | [2] | SHIM (1.05-MM THK) | ||
| 128-7686 B | [2] | SHIM (1.1-MM THK) | ||
| 128-7687 B | [2] | SHIM (1.15-MM THK) | ||
| 128-7688 B | [2] | SHIM (1.25-MM THK) | ||
| 128-7689 B | [2] | SHIM (1.3-MM THK) | ||
| 128-7690 B | [2] | SHIM (1.35-MM THK) | ||
| 7T-0558 B | [2] | SHIM (1.4-MM THK) | ||
| 128-7691 B | [2] | SHIM (1.45-MM THK) | ||
| 128-7692 B | [2] | SHIM (1.5-MM THK) | ||
| 128-7693 B | [2] | SHIM (1.55-MM THK) | ||
| 128-7694 B | [2] | SHIM (1.6-MM THK) | ||
| 128-7695 B | [2] | SHIM (1.65-MM THK) | ||
| 7T-0552 B | [2] | SHIM (2-MM THK) | ||
| 202-8137 B | [2] | SHIM (1.47-MM THK) | ||
| 202-8138 B | [2] | SHIM (1.63-MM THK) | ||
| 202-8139 B | [2] | SHIM (1.75-MM THK) | ||
| 202-8140 B | [2] | SHIM (1.7-MM THK) | ||
| 202-8141 B | [2] | SHIM (1.8-MM THK) | ||
| 202-8142 B | [2] | SHIM (1.85-MM THK) | ||
| 202-8143 B | [2] | SHIM (1.9-MM THK) | ||
| 202-8144 B | [2] | SHIM (1.95-MM THK) | ||
| 79. | 121-7637 | [2] | RING-BACKUP | |
| 80. | 121-7638 | [2] | RING | |
| 81. | 121-7639 | [4] | RING | |
| 82. | 121-7640 | [2] | PISTON-BRAKE | |
| 83. | 223-7967 | [2] | GEAR | |
| 84. | 5W-7320 | [2] | RING | |
| 85. | 178-8608 | [2] | CONE-TAPERED | |
| 86. | 5W-5480 | [4] | SEAL-O-RING | |
| 87. | 5W-6845 | [2] | SEAL-O-RING | |
| 88. | 8U-5722 | [2] | FLANGE | |
| 89. | 2S-0479 | [2] | CONE-BEARING (TAPERED ROLLER) | |
| 90. | 8U-0747 B | [2] | SPACER (109.7X120.3X15.2-MM THK) | |
| 8U-0748 B | [2] | SPACER (109.7X120.3X15-MM THK) | ||
| 8U-0749 B | [2] | SPACER (109.7X120.3X14.8-MM THK) | ||
| 8U-0750 B | [2] | SPACER (109.7X120.3X14.6-MM THK) | ||
| 8U-0751 B | [2] | SPACER (109.7X120.3X14.4-MM THK) | ||
| 8U-0752 B | [2] | SPACER (109.7X120.3X14.2-MM THK) | ||
| 8U-0753 B | [2] | SPACER (109.7X120.3X14-MM THK) | ||
| 121-7642 B | [2] | SPACER (109.7X120.3X14.42-MM THK) | ||
| 121-7643 B | [2] | SPACER (109.7X120.3X14.45-MM THK) | ||
| 121-7644 B | [2] | SPACER (109.7X120.3X14.48-MM THK) | ||
| 121-7645 B | [2] | SPACER (109.7X120.3X14.51-MM THK) | ||
| 121-7646 B | [2] | SPACER (109.7X120.3X14.54-MM THK) | ||
| 91. | 2S-0480 | [4] | CUP-TAPERED ROLLER | |
| 92. | 6R-5257 | [2] | SEAL AS | |
| 93. | 5W-7640 | [2] | SCREW | |
| 94. | 121-7656 | [2] | FITTING | |
| 95. | 7X-5804 | [2] | SEAL-O-RING | |
| 96. | 5W-5682 | [2] | VALVE AS-PURGE (AXLE) | |
| 97. | 121-7657 Y | [2] | UNIVERSAL JOINT GP | |
| 98. | 128-7867 | [4] | FITTING-HYDRAULIC | |
| 99. | 8T-4779 M | [16] | BOLT (M16X2X35-MM) | |
| 100. | 110-0860 | [4] | PIN-BEARING | |
| 101. | 121-7659 B | [2] | SHIM (0.6-MM THK) | |
| 121-7661 B | [2] | SHIM (0.8-MM THK) | ||
| 121-7662 B | [2] | SHIM (1-MM THK) | ||
| 121-7663 B | [2] | SHIM (1.2-MM THK) | ||
| 121-7665 B | [2] | SHIM (1.6-MM THK) | ||
| 121-7667 B | [2] | SHIM (2-MM THK) | ||
| 102. | 110-4743 | [4] | SEAL-O-RING | |
| 103. | 110-0858 | [4] | CAP-SEALING | |
| 104. | 4D-8648 | [4] | CUP-BEARING | |
| 6V-2652 | [4] | CONE-BEARING | ||
| 105. | 121-7670 | [1] | HOUSING GP-AXLE (RH) | |
| 121-7668 | [1] | NUT | ||
| 106. | 121-7669 | [1] | HOUSING GP-AXLE (LH) | |
| 121-7668 | [1] | NUT | ||
| 107. | 132-6522 | [1] | TIE ROD GP (RH) | |
| 5W-5374 | [1] | ROD AS | ||
| 132-6525 | [1] | TIE ROD AS | ||
| 8U-9402 | [1] | CLAMP | ||
| 8U-0728 | [1] | NUT | ||
| 5W-1471 | [1] | PIN-COTTER | ||
| 108. | 132-6521 | [1] | TIE ROD GP (LH) | |
| 5W-5374 | [1] | ROD AS | ||
| 132-6524 | [1] | TIE ROD AS | ||
| 8U-9402 | [1] | CLAMP | ||
| 8U-0728 | [1] | NUT | ||
| 5W-1471 | [1] | PIN-COTTER | ||
| 109. | 121-7675 | [4] | BUSHING | |
| 110. | 9R-6996 | [4] | SEAL | |
| 111. | 175-4073 | [2] | BUSHING-SLEEVE | |
| 112. | 9R-6948 | [4] | CLIP | |
| 113. | 204-7842 | [2] | SHAFT-AXLE | |
| 114. | 9R-7003 | [1] | BEARING-TAPERED ROLLER | |
| 115. | 216-0590 | [1] | ROD AS | |
| 116. | 203-0215 | [3] | SEAL-O-RING | |
| 117. | 7T-9343 | [1] | CUP-BEARING | |
| B | USE AS REQUIRED | |||
| C | CHANGE FROM PREVIOUS TYPE | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP42230166
112-5439: AXLE AR-REAR
112-5439 AXLE AR-REAR
S/N BDX2001-99999
PART OF 175-6559 AXLE & TRANSMISSION AR
AN ATTACHMENT
S/N BDX2001-99999
PART OF 175-6559 AXLE & TRANSMISSION AR
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8U-5919 | [1] | HOUSING-AXLE | |
| 2. | 109-4440 | [1] | PLUG | |
| 3. | 110-0847 | [1] | PLUG-SCREW | |
| 4. | 190-8676 | [2] | SEAL-O-RING | |
| 5. | 5W-8311 | [2] | ROD-AXLE | |
| 6. | 9R-3533 M | [14] | BOLT-SPECIAL | |
| 7. | 211-7102 | [2] | HUB GP-WHEEL | |
| (EACH INCLUDES) | ||||
| 7A. | 211-7104 | [1] | NUT (M95X1.5-THD) | |
| 8. | 8T-6429 M | [36] | BOLT-SOCKET HEAD (M16X2X55-MM) | |
| 9. | 5W-3061 | [2] | SEAL-O-RING | |
| 10. | 121-8133 | [2] | PLATE-BACKING | |
| 12. | 5W-5682 | [2] | VALVE AS-PURGE (AXLE) | |
| 13. | 8U-5923 | [2] | FITTING AS | |
| 14. | 8U-2233 | [2] | SEAL-O-RING | |
| 15. | 4K-2039 | [2] | SEAL-O-RING | |
| 16. | 121-8168 | [2] | SEAL-LIP TYPE | |
| 17. | 121-8167 | [2] | BEARING-ROLLER | |
| 18. | 121-8153 B | [2] | RING (3.4-MM THK) | |
| 121-8154 B | [2] | RING (3.6-MM THK) | ||
| 121-8155 B | [2] | RING (3.8-MM THK) | ||
| 121-8156 B | [2] | RING (4-MM THK) | ||
| 121-8157 B | [2] | RING (4.1-MM THK) | ||
| 121-8158 B | [2] | RING (4.2-MM THK) | ||
| 121-8159 B | [2] | RING (4.3-MM THK) | ||
| 121-8160 B | [2] | RING (4.4-MM THK) | ||
| 121-8161 B | [2] | RING (4.5-MM THK) | ||
| 121-8162 B | [2] | RING (4.6-MM THK) | ||
| 121-8163 B | [2] | RING (4.7-MM THK) | ||
| 121-8164 B | [2] | RING (4.8-MM THK) | ||
| 121-8165 B | [2] | RING (4.9-MM THK) | ||
| 121-8166 B | [2] | RING (5-MM THK) | ||
| 32. | 5W-6367 | [2] | BEARING | |
| 33. | 121-8152 | [2] | HUB-WHEEL | |
| 34. | 5W-6845 | [2] | SEAL-O-RING | |
| 36. | 5W-5480 | [4] | SEAL-O-RING | |
| 37. | 8U-3834 | [2] | SPACER (95.5X105.55X3.8-MM THK) | |
| 38. | 5W-7320 | [2] | RING | |
| 39. | 223-7967 | [2] | GEAR | |
| 40. | 121-7640 | [2] | PISTON-BRAKE | |
| 41. | 121-7639 | [4] | RING | |
| 42. | 121-7638 | [2] | RING | |
| 43. | 121-7637 | [2] | RING-BACKUP | |
| 44. | 8U-5698 | [2] | PLATE-WASHER | |
| 45. | 8U-3592 | [12] | SPRING | |
| 46. | 8U-3594 | [12] | NUT | |
| 47. | 121-7636 M | [12] | BOLT (M6X1X40-MM) | |
| 48. | 8U-3591 | [12] | SPACER (6.5X15X7-MM THK) | |
| 49. | 5W-7381 | [2] | SHAFT-SEAL | |
| 50. | 121-7635 B | [12] | DISC-GEAR (2-MM THK) | |
| 51. | 121-7634 B | [12] | DISC-GEAR (2.5-MM THK) | |
| 52. | 121-7633 B | [12] | DISC-GEAR (3-MM THK) | |
| 53. | 121-7632 | [10] | DISC-FRICTION | |
| 54. | 5W-6404 | [2] | WASHER | |
| 55. | 121-7631 | [2] | RING-RETAINING | |
| 56. | 8U-0746 | [2] | WASHER-THRUST | |
| 57. | 121-8141 | [2] | GEAR-SUN | |
| 58. | 121-8140 | [2] | SEAL-O-RING | |
| 59. | 121-8139 | [2] | CARRIER | |
| 60. | 5W-6370 | [2] | RING-RETAINING | |
| 61. | 121-7628 | [2] | HOUSING-DRIVE | |
| 62. | 9R-6950 | [8] | PINION-PLANETARY | |
| 63. | 121-7627 | [8] | BEARING-ROLLER | |
| 64. | 9R-6949 | [16] | RING | |
| 65. | 8T-2355 | [8] | RING-RETAINING | |
| 66. | 054-6552 B | [2] | SHIM (1.5-MM THK) | |
| 054-6553 B | [2] | SHIM (2-MM THK) | ||
| 054-6554 B | [2] | SHIM (2.5-MM THK) | ||
| 054-6555 B | [2] | SHIM (3-MM THK) | ||
| 054-6556 B | [2] | SHIM (1.7-MM THK) | ||
| 054-6557 B | [2] | SHIM (2.2-MM THK) | ||
| 8U-2751 B | [2] | WASHER-THRUST | ||
| 73. | 203-0215 | [2] | SEAL-O-RING | |
| 74. | 121-7626 | [2] | PLUG | |
| 75. | 5W-2177 M | [4] | BOLT-SOCKET HEAD (M12X1.75X20-MM) | |
| 76. | 054-7758 | [20] | STUD | |
| 77. | 9X-0641 | [20] | WASHER | |
| 78. | 5W-5694 | [20] | RING | |
| 79. | 9X-0642 | [20] | NUT | |
| 80. | 9W-4926 | [2] | PLUG | |
| 81. | 6T-6408 | [2] | SEAL-O-RING | |
| B | USE AS REQUIRED | |||
| M | METRIC PART | |||
#SEBP42230167
129-2672: AXLE AR-REAR
129-2672 AXLE AR-REAR
S/N BDX2001-99999
PART OF 175-6562 AXLE & TRANSMISSION AR
AN ATTACHMENT
S/N BDX2001-99999
PART OF 175-6562 AXLE & TRANSMISSION AR
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 129-3457 | [1] | HOUSING-AXLE | |
| 2. | 109-4440 | [1] | PLUG | |
| 3. | 110-0847 | [1] | PLUG-SCREW | |
| 4. | 190-8676 | [2] | SEAL-O-RING | |
| 5. | 129-3458 | [2] | SHAFT | |
| 6. | 9R-3533 M | [14] | BOLT-SPECIAL | |
| 7. | 129-2704 | [2] | SLEEVE | |
| 8. | 129-2705 | [2] | RING-RETAINING | |
| 9. | 246-6872 C | [2] | HUB GP-WHEEL | |
| (EACH INCLUDES) | ||||
| 10. | 246-6871 | [1] | NUT-SPECIAL | |
| 11. | 8T-2393 M | [6] | BOLT-SOCKET HEAD (M16X2X60-MM) | |
| 12. | 5W-3061 | [2] | SEAL-O-RING | |
| 13. | 121-8133 | [2] | PLATE-BACKING | |
| 14. | 121-8168 | [2] | SEAL-LIP TYPE | |
| 15. | 121-8167 | [2] | BEARING-ROLLER | |
| 16. | 121-8153 B | [2] | RING (3.4-MM THK) | |
| 121-8154 B | [2] | RING (3.6-MM THK) | ||
| 121-8155 B | [2] | RING (3.8-MM THK) | ||
| 121-8156 B | [2] | RING (4-MM THK) | ||
| 121-8157 B | [2] | RING (4.1-MM THK) | ||
| 121-8158 B | [2] | RING (4.2-MM THK) | ||
| 121-8159 B | [2] | RING (4.3-MM THK) | ||
| 121-8160 B | [2] | RING (4.4-MM THK) | ||
| 121-8161 B | [2] | RING (4.5-MM THK) | ||
| 121-8162 B | [2] | RING (4.6-MM THK) | ||
| 121-8163 B | [2] | RING (4.7-MM THK) | ||
| 121-8164 B | [2] | RING (4.8-MM THK) | ||
| 121-8165 B | [2] | RING (4.9-MM THK) | ||
| 121-8166 B | [2] | RING (5-MM THK) | ||
| 17. | 158-6333 Y | [2] | BRAKE GP-DRUM | |
| 18. | 129-2720 | [2] | DRUM-BRAKE | |
| 19. | 9X-0642 | [20] | NUT | |
| 20. | 5W-5694 | [20] | RING | |
| 21. | 9X-0641 | [20] | WASHER | |
| 22. | 129-2718 | [20] | STUD-WHEEL | |
| 23. | 5W-2177 M | [4] | BOLT-SOCKET HEAD (M12X1.75X20-MM) | |
| 24. | 3T-8699 | [2] | PLUG | |
| 25. | 6T-6403 | [2] | SEAL-O-RING | |
| 26. | 054-6552 B | [2] | SHIM (1.5-MM THK) | |
| 054-6553 B | [2] | SHIM (2-MM THK) | ||
| 054-6554 B | [2] | SHIM (2.5-MM THK) | ||
| 054-6555 B | [2] | SHIM (3-MM THK) | ||
| 129-2714 B | [2] | SHIM (3.5-MM THK) | ||
| 129-2715 B | [2] | SHIM (4-MM) | ||
| 129-2716 B | [2] | SHIM (4.5-MM THK) | ||
| 129-2717 B | [2] | SHIM (5-MM THK) | ||
| 27. | 8T-2355 | [8] | RING-RETAINING | |
| 28. | 9R-6949 | [16] | RING | |
| 29. | 121-7627 | [8] | BEARING-ROLLER | |
| 30. | 2S-0479 C | [2] | CONE-BEARING (TAPERED ROLLER) | |
| 31. | 129-2709 | [2] | HUB-WHEEL | |
| 32. | 110-4745 C | [2] | SEAL-O-RING | |
| 33. | 129-2710 | [2] | GEAR-INTERNAL | |
| 34. | 246-6870 C | [2] | PLATE-LOCK | |
| 35. | 096-4835 CM | [4] | BOLT-SOCKET HEAD (M10X1.5X16-MM) | |
| 36. | 129-2712 | [2] | GEAR-SUN | |
| 37. | 129-2713 | [2] | HOUSING-DRIVE | |
| 38. | 9R-6950 | [8] | PINION-PLANETARY | |
| 39. | 8T-1447 M | [30] | BOLT-SOCKET HEAD (M16X2X70-MM) | |
| 40. | 2R-0409 | [36] | WASHER (16.66X24.64X3-MM THK) | |
| 41. | 2S-0480 | [2] | CUP-TAPERED ROLLER | |
| B | USE AS REQUIRED | |||
| C | CHANGE FROM PREVIOUS TYPE | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP42230168
188-4933: AXLE AR-REAR
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS#SEBP42230169
188-4935: AXLE AR-REAR
188-4935 AXLE AR-REAR
S/N BDX2001-99999
PART OF 188-4933 AXLE AR-REAR, 250-2704 AXLE AR-WIDE
AN ATTACHMENT
S/N BDX2001-99999
PART OF 188-4933 AXLE AR-REAR, 250-2704 AXLE AR-WIDE
AN ATTACHMENT
For full view, you need register
Parts for your M316C WHEELED EXCAVATOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 6V-7688 M | [8] | LOCKNUT (M20X2.5-THD) | |
| 2. | 7Y-1858 | [16] | WASHER (21X37X3-MM THK) | |
| 3. | 123-8324 | [2] | CAP | |
| 4. | 124-5215 | [2] | FITTING AS (QUICK DISCONNECT) | |
| 5. | 132-4618 | [2] | ADAPTER AS | |
| 6. | 149-1249 I | [2] | HOSE AS | |
| 7. | 175-6562 Y | [1] | AXLE & TRANSMISSION AR (WIDE, DRUM BRAKE) | |
| 8. | 6V-6560 | [2] | SEAL-O-RING | |
| 9. | 8T-0656 M | [8] | BOLT (M20X2.5X150-MM) | |
| -OR- | ||||
| 8T-7505 M | [8] | BOLT (M20X2.5X220-MM) | ||
| 10. | 5W-5694 | [20] | RING | |
| 11. | 9X-0641 | [20] | WASHER | |
| 12. | 9X-0642 | [20] | NUT | |
| I | REFER TO HYDRAULIC INFORMATION SYSTEM | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
Information:
POWER TRAIN
AXLE GP
Operation and Maintenance Manual
Axle Bearings (Front) - Lubricate
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Axle Oscillation Bearings - Lubricate
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Oscillating Axle Control
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Oil Level (Front) - Check
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Axle Oil Level (Rear) - Check
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Axle Oil Sample - Obtain - Rear
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Axle Oil Sample - Obtain - Front
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Axle Oil Level (Front) - Check
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Oil Level (Rear) - Check
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Oil Sample - Obtain
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Oil Sample - Obtain - Front
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Bearings (Front) - Lubricate
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Oscillation Bearings - Lubricate - If Equipped
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Oil (Front) - Change
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Axle Oil (Rear) - Change
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Wheel Nut Torque - Check
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Special Instruction
Service Letter-NACD
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT AXLE PINION ON CERTAIN M300C SERIES WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT AXLE PINION ON CERTAIN M300C SERIES WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT AXLE PINION ON CERTAIN M300C SERIES WHEELED EXCAVATORS
Service Letter-Australia
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
Service Letter-CFEL
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
Service Letter-CSARL
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT AXLE PINION ON CERTAIN M300C SERIES WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT AXLE PINION ON CERTAIN M300C SERIES WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT AXLE PINION ON CERTAIN M300C SERIES WHEELED EXCAVATORS
Service Letter-Americas
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
Specifications
Service Letter-China
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
Service Letter-Asia
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
Systems Operation
Axle (Front and Rear)
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Excavators Hydraulic System
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Excavators Hydraulic System
Solenoid Valve (Oscillating Axle)
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Excavators Hydraulic System
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Excavators Hydraulic System
Oscillating Axle
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Excavators Hydraulic System
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Excavators Hydraulic System
Transmission
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
Oscillating Axle
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
Solenoid Valve (Oscillating Axle)
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
Axle (Front and Rear)
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
M313C, M315C, M316C, M318C, M322C, M318C MH and M322C MH Wheeled Excavators Hydraulic System
Reuse And Salvage Guidelines
Specifications for Inspection of Driveline Fasteners {3030, 3101, 3159, 3253, 3258, 3278, 4050}
Specifications for Inspection of Driveline Fasteners {3030, 3101, 3159, 3253, 3258, 3278, 4050}
Specifications for Inspection of Driveline Fasteners {3030, 3101, 3159, 3253, 3258, 3278, 4050}
Contamination Control Guidelines
Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}
Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}
Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}
Obtaining Oil Sample for Analysis {1302, 1348, 3030, 3080, 3278, 4011, 4070, 5050, 5056, 5095, 7542}
Obtaining Oil Sample for Analysis {1302, 1348, 3030, 3080, 3278, 4011, 4070, 5050, 5056, 5095, 7542}
Obtaining Oil Sample for Analysis {1302, 1348, 3030, 3080, 3278, 4011, 4070, 5050, 5056, 5095, 7542}
Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050}
Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050}
Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050}
Service Letter-APD
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING AXLE HOUSING ON CERTAIN M315C, M316C & M318C WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AXLE TRUNNION BOLTS ON CERTAIN M313C, M315C, M316C, M318C, AND M318D WHEELED EXCAVATORS
Testing and Adjusting
Axle (Steering Alignment) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System
Axle (Steering Positive Stop) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System
Brake Disc Wear - Measure
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System
Disassembly and Assembly
Final Drive Carriers, Hubs and Brakes - Disassemble - Front Axle
M316C Wheeled Excavator Power Train
M316C Wheeled Excavator Power Train
Final Drive Carriers, Hubs and Brakes - Disassemble - Front Axle
M316C Wheeled Excavator Power Train
M316C Wheeled Excavator Power Train
Service Magazine
Measuring Ring Helps the Technician Adjust the Pinion for the Proper Rolling Torque {0722, 0767}
2005/03/28
2005/03/28
Caterpillar Parts SIS Catalog M316C :
Truck sale:
63,000
