OPERATOR STATION
WASHER GP-WINDOWWIPER GP-WINDOW
SERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMSTOOLS
LUBRICANTS & FLUIDS
WORK TOOLS
BUCKET GPSERVICE EQUIPMENT AND SUPPLIES
PROTECTION GPCHARTS & FILMS
OPERATOR STATION
WASHER GP-WINDOW
#SEBP46080600
206-1728: WIPER & WASHER GP-WINDOW
206-1728 WIPER & WASHER GP-WINDOW
S/N BWC1-UP
PART OF 291-9192 CANOPY AR-OPEN ROPS
AN ATTACHMENT
S/N BWC1-UP
PART OF 291-9192 CANOPY AR-OPEN ROPS
AN ATTACHMENT
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 3S-2093 | [10] | STRAP-CABLE | |
| 2. | 276-8791 | [1] | CLIP | |
| 3. | 8T-1118 | [1] | NOZZLE AS-WASHER | |
| 4. | 9R-3469 | [1] | DIAPHRAGM | |
| 5. | 101-0745 | [1] | BLADE AS-WIPER (600-MM)(FRONT) | |
| 6. | 283-3451 | [1] | CONNECTOR AS | |
| 7. | 213-6051 | [1] | HARNESS AS-CAB (WIPER MOTOR) | |
| 9W-0852 | [1] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 9X-3401 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 155-2265 | [1] | KIT-CONNECTING PLUG (8-PIN) | ||
| 155-2271 | [2] | KIT-CONNECTING PLUG (4-PIN) | ||
| 155-2274 | [1] | KIT-CONNECTING PLUG (6-PIN) | ||
| (EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 8T-8737 | [3] | PLUG-SEAL | ||
| 102-8805 | [1] | KIT-RECEPTACLE (6-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 9W-0844 | [5] | SOCKET-CONNECTOR (14-GA TO 16-GA) | ||
| 180-9340 | [15] | SOCKET-CONNECTOR (14-GA TO 18-GA) | ||
| 8L-8413 | [15] | STRAP-CABLE (WHITE) | ||
| 9R-9442 | [2] | TERMINAL | ||
| 2L-8069 | [1] | TERMINAL-RING (2-GA TO 10-GA, 3/8-IN SCREW) | ||
| 5P-4571 | [2] | TERMINAL-BLADE (14-GA TO 16-GA) | ||
| 119-3662 E | TUBE-HEAT SHRINK (10.85-MM DIA)(7-CM) | |||
| 125-7874 E | TUBE-HEAT SHRINK (5.72-MM DIA)(5-CM) | |||
| 6V-2689 D | TUBE-HEAT SHRINK (6.35-MM DIA)(0.1-M) | |||
| 8. | 154-5410 | [1] | ARM-WINDOW WIPER | |
| 9. | 186-2589 Y | [1] | MOTOR GP-WINDOW WIPER (FRONT) | |
| 10. | 214-3763 | [1] | TANK GP-WINDOW WASHER | |
| 6T-1375 | [2] | PUMP AS-WASHER | ||
| 8E-8293 | [2] | GROMMET | ||
| 214-3742 | [1] | TANK-WASHER | ||
| 254-5683 | [1] | CAP | ||
| 11. | 6V-7357 M | [1] | BOLT (M6X1X25-MM) | |
| 12. | 8T-4205 | [1] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 13. | 144-0195 E | HOSE (217-CM) | ||
| 13A. | 144-0195 E | HOSE (79-CM) | ||
| 13B. | 144-0195 E | HOSE (297-CM) | ||
| 13C. | 144-0195 E | HOSE (15-CM EACH) | ||
| 14. | 156-0283 | [2] | WASHER-HARD (8.4X35X2.5-MM THK) | |
| 15. | 9X-8372 | [1] | FILM-INSTRUCTION (WASHER FILL) | |
| 16. | 8T-5093 M | [1] | BOLT-LOCKING (M8X1.25X25-MM) | |
| 17. | 6K-9632 | [1] | TEE | |
| D | ORDER BY THE METER | |||
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP46080601
206-1725: WIPER GP-WINDOW
206-1725 WIPER GP-WINDOW
S/N BWC1-UP
PART OF 291-9193, 291-9194, 291-9195 CAB AR-ENCLOSED ROPS
AN ATTACHMENT
S/N BWC1-UP
PART OF 291-9193, 291-9194, 291-9195 CAB AR-ENCLOSED ROPS
AN ATTACHMENT
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 5C-8811 | [1] | BLADE AS-WIPER (500-MM)(REAR) | |
| 2. | 101-0745 | [1] | BLADE AS-WIPER (600-MM)(FRONT) | |
| 3. | 154-5410 | [1] | ARM-WINDOW WIPER (FRONT) | |
| 4. | 160-2169 | [2] | SPACER (7X11X8.4-MM THK) | |
| 5. | 186-2589 Y | [1] | MOTOR GP-WINDOW WIPER (FRONT) | |
| 6. | 214-4709 | [1] | SWITCH AS-ROCKER (WIPER, WASHER, REAR) | |
| 111-7899 | [1] | GASKET | ||
| 7. | 220-2000 | [1] | MOTOR GP-WINDOW WIPER (REAR) | |
| 186-3735 | [5] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8. | 220-2001 | [1] | ARM AS-WIPER (REAR) | |
| 136-3194 | [1] | NOZZLE AS-WASHER | ||
| 194-5171 E | HOSE (35-CM) | |||
| 9. | 223-8263 | [1] | PLATE | |
| 10. | 229-0306 | [1] | PLATE | |
| 11. | 6V-7357 M | [1] | BOLT (M6X1X25-MM) | |
| 12. | 8T-4138 M | [2] | BOLT (M6X1X20-MM) | |
| 13. | 8T-4171 M | [4] | BOLT (M6X1X12-MM) | |
| 14. | 8T-4205 | [9] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 15. | 5C-2890 M | [1] | NUT (M6X1-THD) | |
| 16. | 8T-4971 M | [1] | BOLT (M6X1X30-MM) | |
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP46080602
306-7466: FILM GP
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | [1] | FILM-IDENTIFICATION (416E, RH) | ||
| 2. | [1] | FILM-IDENTIFICATION (BOOM, RH) | ||
| 3. | [1] | FILM-IDENTIFICATION (416E, LH) | ||
| 4. | [1] | FILM-IDENTIFICATION (BOOM, LH) | ||
#SEBP46080603
113-0018: INSTALLATION AR-WHEEL CHOCK
113-0018 INSTALLATION AR-WHEEL CHOCK
S/N BWC1-UP
FIELD INSTALLATION ONLY
AN ATTACHMENT
S/N BWC1-UP
FIELD INSTALLATION ONLY
AN ATTACHMENT
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS#SEBP46080604
447-2201: KIT-PREVENTIVE MAINTENANCE
447-2201 KIT-PREVENTIVE MAINTENANCE
S/N BWC1-UP
500-HOUR
FIELD INSTALLATION
S/N BWC1-UP
500-HOUR
FIELD INSTALLATION
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 361-9554 | [1] | ELEMENT-WATER SEPARATOR | ||
| 7W-2326 | [1] | FILTER AS-ENGINE OIL | ||
| 9R-9925 | [1] | BREATHER-HYDRAULIC (INLINE) | ||
| 156-1200 | [1] | FILTER ELEMENT-FUEL (WATER SEPARATOR) | ||
| 119-4740 | [1] | FILTER-OIL (STANDARD EFFICIENCY) | ||
| 126-1817 | [1] | FILTER-OIL (ULTRA HIGH EFFICIENCY) | ||
| 275-9883 | [1] | SEAL | ||
| 267-6532 | [1] | TOWEL |
#SEBP46080605
175-7877: LINK GP-SHIPPING
175-7877 LINK GP-SHIPPING
S/N BWC1-UP
REQUIRED WHEN NO BACKHOE BUCKET IS INSTALLED
AN ATTACHMENT
S/N BWC1-UP
REQUIRED WHEN NO BACKHOE BUCKET IS INSTALLED
AN ATTACHMENT
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 120-9286 | [1] | PLATE |
#SEBP46080606
216-0909: LOCK GP-VANDALISM
216-0909 LOCK GP-VANDALISM
S/N BWC1-UP
FOR USE WITH SINGLE TILT LOADER
AN ATTACHMENT
S/N BWC1-UP
FOR USE WITH SINGLE TILT LOADER
AN ATTACHMENT
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 246-2641 J | [1] | PADLOCK GP (VANDALISM GUARD) | ||
| J | REQUIRES 5P-8500 KEY | |||
#SEBP46080607
263-8591: PLATE & FILM GP
263-8591 PLATE & FILM GP
S/N BWC1-UP
PART OF 216-8801 BUCKET GP-MULTIPURPOSE
AN ATTACHMENT
S/N BWC1-UP
PART OF 216-8801 BUCKET GP-MULTIPURPOSE
AN ATTACHMENT
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 247-6118 | [2] | FILM-WARNING (CRUSH HAZARD, STAY BACK) |
#SEBP46080608
291-9200: PLATE & FILM GP
291-9200 PLATE & FILM GP -NACD
S/N BWC1-UP
PART OF 374-1864, 374-1865 DISTRIBUTION AR
AN ATTACHMENT
S/N BWC1-UP
PART OF 374-1864, 374-1865 DISTRIBUTION AR
AN ATTACHMENT
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 239-6989 | [1] | PLATE-SERIAL NUMBER (MACHINE) | ||
| (SEE CHART LOCATION) | ||||
| 225-4150 | [1] | PLATE-SERVICE INFORMATION (MACHINE) | ||
| (SEE CHART LOCATION) | ||||
| 193-5913 | [6] | PLUG | ||
| [1] | FILM-INSTRUCTION (BOOM LOCK) | |||
| (NEXT TO BOOM LOCK ON RH CONSOLE) | ||||
| [1] | FILM-INSTRUCTION (VARIABLE SPEED) | |||
| (RH CONSOLE NEXT TO GOV CONTROL HANDLE) | ||||
| 252-8435 | [1] | FILM-IDENTIFICATION (START SWITCH, READ OMM) | ||
| (RH CONSOLE AROUND KEYSWITCH) | ||||
| 258-9999 | [4] | FILM-IDENTIFICATION (LIFT EYE LOCATION) | ||
| (TOTAL OF 4 FILMS. 2 FILMS APPLIED TO THE FRONT SIDE OF THE FRONT AXLE BETWEEN THE CHASSIS & WHEEL ASSEMBLY ON THE LH | ||||
| & RH SIDE OF THE MACHINE. THE REMAINDER 2 FILMS TO BE APPLIED TO THE STAB PAD CENTERED UNDER THE LIFTING HOLE ORIENTED | ||||
| WITH THE ARROW POINTING UP WHEN THE STABILIZER IS IN THE UPPER WARD POSITION) | ||||
| 289-3412 | [1] | FILM-COVER (PROTECT) | ||
| (IN THE BATTERY BOX ON THE LH SIDE 150 +/-5MM UP FROM THE BOTTOM OF THE BOX & LEVEL WITH THE BOTTOM OF BOX | ||||
| CENTERED FROM SIDE TO SIDE) | ||||
| 159-3590 | [1] | FILM-IDENTIFICATION (WATER SEPARATOR) | ||
| (LEFT SIDE OF THE MAIN FRAME NEXT TO THE FUEL TANK. 20MM +/-10 FROM THE FUEL TANK | ||||
| BRACKET & UP FROM THE BOTTOM EDGE OF THE MAIN FRAME FROME 50MM +/-10 | ||||
| 159-8033 | [1] | FILM-IDENTIFICATION (12-VOLT) | ||
| (INSIDE BATTERY BOX DOOR CENTERED FROM SIDE TO SIDE ABOVE THE JUMP START WARNING FILM & | ||||
| CENTERED FROM TOP TO BOTTOM BETWEEN THE JUMP START FILM & THE BEND IN THE DOOR) | ||||
| [1] | FILM-IDENTIFICATION (FUSE PANEL) | |||
| (INSIDE RH CONSOLE ACCESS PANEL SUCH THAT IT CAN BE READ WHILE STANDING ON THE GROUND WITH THE ACCESS DOOR OPEN | ||||
| & VIEWING FILM) | ||||
| 134-7258 | [1] | FILM-INFORMATION (EXTENDED LIFE COOLANT) | ||
| (SHUNT TANK NEXT TO RADIATOR CAP SUCH THAT IT CAN BE READ FROM THE LEFT SIDE OF THE MACHINE) | ||||
| [1] | FILM-ROPS (OPS, READ OMM) | |||
| (LH A-POST 350 +/-5MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO DRILL & THE ROPS/FOPS FILM IN THE | ||||
| LOWER POSITION) | ||||
| 252-2157 | [4] | FILM-INFORMATION (TIE-DOWN) | ||
| APPLY 2 FILMS, ONE ON EACH SIDE OF MACHINE ON THE MAIN FRAME ABOVE THE FRONT AXLE, ABOVE TIE DOWN MOUNTING PLATE, | ||||
| CENTERED TOP TO BOTTOM & RIGHT TO LEFT.APPLY OTHER 2 FILMS IN THE REAR OF THE MACHINE ON THE MAIN FRAME NEXT TO THE | ||||
| TIE DOWN HOLES UNDER THE SWING CYLINDERS) | ||||
| 124-2456 | [1] | FILM-INSTRUCTION (NO STEP) | ||
| (INSIDE BATTERY BOX DOOR 75+/-5MM FROM THE RIGHT EDGE & THE TOP EDGE IS EVEN WITH 12V FILM) | ||||
| [1] | FILM-INSTRUCTION (LUBRICATION POINTS) | |||
| (UNDER HOOD ON PRE-CLEANER SUCH THAT IT CAN BE READ FROM THE LEFT SIDE OF MACHINE) | ||||
| 219-0302 | [1] | FILM-WARNING (NO WELD, NO DRILL, READ OMM) | ||
| (LH A-POST 350 +/-5MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO DRILL & THE ROPS/FOPS FILM IN THE | ||||
| LOWER POSITION) | ||||
| 224-8945 | [1] | FILM-WARNING (DO NOT USE ETHER, U.S.) | ||
| (UNDER HOOD ON THE PRE-CLEANER UNDER THE SERVICE FILM SUCH THAT IT CAN BE READ FROM THE LEFT SIDE OF THE MACHINE) | ||||
| 225-0313 | [1] | FILM-WARNING (JUMP START, READ OMM, U.S.) | ||
| (INSIDE OF BATTERY BOX DOOR CENTERED ABOVE DOOR LATCH & 75+/-5 UP FROM THE EDGE OF DOOR) | ||||
| 226-1242 | [2] | FILM-WARNING (CRUSH HAZARD, STAY BACK, U.S.) | ||
| (ON BOOM 700MM +/-5 UP FROM CENTER LINE OF SWING & BOOM LOWER FOOT PIN & 65MM +/-OVER FROM INSIDE OF THE REAR EDGE OF | ||||
| BOOM WRAPPER PLATE) | ||||
| 239-9429 | [1] | FILM-WARNING (ARM BRACE, READ OMM, U.S.) | ||
| LH SIDE OF MACHINE ON SAFETY BRACE CENTERED FROM TOP TO BOTTOM & FROM SIDE TO SIDE) | ||||
| 240-7094 | [2] | FILM-WARNING (NO ENTRANCE, EXIT, READ OMM) | ||
| (REAR OF CAB STRUCTURE AT BOTTOM 50 +/-5MM FROM THE RED REFLECTOR TOWARD CENTER OF MACHINE FOR BOTH FILMS. CENTERED FROM | ||||
| TOP TO BOTTOM) | ||||
| 255-0791 | [1] | FILM-WARNING (READ OMM) | ||
| (RH CONSOLE UNDER KEYSWITCH IN AREA PROVIDED. UNIVERSAL FILM IS LOCATED ON UPPER HALF & THE SEATBELT IS ON THE LOWER | ||||
| HALF) | ||||
| 255-0792 | [1] | FILM-WARNING (SEAT BELT) | ||
| (RH CONSOLE UNDER KEYSWITCH IN AREA PROVIDED. UNIVERSAL FILM IS LOCATED ON UPPER HALF & THE SEATBELT IS ON THE LOWER | ||||
| HALF) | ||||
| 259-4401 | [1] | FILM-WARNING (HOT FLUID UND PRESS, READ OMM) | ||
| (ON RADIATOR CAP SO THAT IT CAN BE READ FROM THE LH SIDE OF MACHINE) | ||||
#SEBP46080609
291-9201: PLATE & FILM GP
For full view, you need register
Parts for your 416E BACKHOE LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 193-5913 | [4] | PLUG | ||
| [1] | FILM-INSTRUCTION (BOOM LOCK) | |||
| (NEXT TO BOOM LOCK ON RH CONSOLE) | ||||
| [1] | FILM-INSTRUCTION (VARIABLE SPEED) | |||
| (ON RH CONSOLE NEXT TO GOV CONTROL HANDLE) | ||||
| 252-8435 | [1] | FILM-IDENTIFICATION (START SWITCH, READ OMM) | ||
| (ON RH CONSOLE AROUND KEYSWITCH) | ||||
| 258-9999 | [4] | FILM-IDENTIFICATION (LIFT EYE LOCATION) | ||
| (APPLY A TOTAL OF 4 FILMS. THE FIRST 2 FILMS ARE TO BE APPLIED TO THE FRONT SIDE OF THE FRONT AXLE BETWEEN THE CHASSIS | ||||
| & WHEEL ASSEMBLY ON THE LH & RH SIDE OF THE MACHINE. THE REMAINDER 2 FILMS ARE TO BE APPLIED TO THE STAB PAD CENTERED | ||||
| UNDER THE LIFTING HOLE ORIENTED WITH THE ARROW POINTING UP WHEN THE STABILIZER IS UN THE UPPER WARD POSITION) | ||||
| [1] | FILM-ROPS (OPS, READ OMM) | |||
| (ON LH A-POST 350 +/-5MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO DRILL & THE ROPS/FOPS FILM IN THE LOWER | ||||
| POSITION) | ||||
| 289-3412 | [1] | FILM-COVER (PROTECT) | ||
| (IN THE BATTERY BOX ON LH SIDE. FILM SHOULD BE 150 +/-5MM UP FROM THE BOTTOM OF THE BOX & LEVEL WITH THE BOTTOM OF BOX | ||||
| CENTERED FROM SIDE TO SIDE) | ||||
| 159-3590 | [1] | FILM-IDENTIFICATION (WATER SEPARATOR) | ||
| (ON LEFT SIDE OF THE MAIN FRAME NEXT TO THE FUEL TANK. 20MM +/-10 FROM THE FUEL TANK BRACKET & UP FROM THE BOTTOM EDGE | ||||
| OF THE MAIN FRAME 50MM +/-10) | ||||
| 159-8033 | [1] | FILM-IDENTIFICATION (12-VOLT) | ||
| (INSIDE BATTERY BOX DOOR CENTERED FROM SIDE TO SIDE ABOVE THE JUMP START WARNING FILM & CENTERED FROMTOP TO BOTTOM | ||||
| BETWEEN THE JUMP START FILM & THE BEND IN DOOR) | ||||
| [1] | FILM-IDENTIFICATION (FUSE PANEL) | |||
| (INSIDE RH CONSOLE ACCESS PANEL SO THAT IT CAN BE READ WHILE STANDING ON THE GROUND WITH THE ACCESS DOOR OPEN & VIEWING | ||||
| FILM) | ||||
| 134-7258 | [1] | FILM-INFORMATION (EXTENDED LIFE COOLANT) | ||
| (ON SHUNT TANK NEXT TO RADIATOR CAP SUCH THAT IT CAN BE READ FROM THE LH SIDE OF THE MACHINE) | ||||
| 252-2157 | [4] | FILM-INFORMATION (TIE-DOWN) | ||
| (APPLY 2 FILMS, ONE ON EACH SIDE OF THE MACHINE ON THE MAIN FRAME ABOVE THE FRONT AXLE, ABOVE THE TIE DOWN MONTING PLATE | ||||
| CENTERED TOP TO BOTTOM & LEFT TO RIGHT. APPLY THE OTHER 2 FILMS IN THE REAR OF THE MACHINE ON THE MAIN FRAME NEXT TO THE | ||||
| TIE DOWN HOLES UNDER THE SWING CYLINDERS) | ||||
| 124-2456 | [1] | FILM-INSTRUCTION (NO STEP) | ||
| (ON INSIDE BATTERY BOX DOOR 75 +/-5MM FROM THE RIGHT EDGE & THE TOP EDGE IS EVEN WITH THE 12V FILM) | ||||
| [1] | FILM-INSTRUCTION (LUBRICATION POINTS) | |||
| (UNDER THE HOOD ON PRE-CLEANER, REMOVE SUPPLIER FILM & ORIENT FILM SUCH THAT IT CAN BE READ FROM THE LEFT SIDE OF THE | ||||
| MACHINE) | ||||
| 219-0302 | [1] | FILM-WARNING (NO WELD, NO DRILL, READ OMM) | ||
| (ON LH A-POST 350 +/-5MM FROM THE FLOOR. THE UPPER FILM SHOULD BE THE NO WELD/NO DRILL & THE ROPS/FOPS FILM IN THE LOWER | ||||
| POSITION) | ||||
| 224-8946 | [1] | FILM-WARNING (NO ETHER SPRAY/AIR INTK, INTL) | ||
| (UNDER HOOD ON THE PRE-CLEANER UNDER THE SERVICE FILM SUCH THAT IT CAN BE READ FROM THE LEFT SIDE OF THE MACHINE) | ||||
| 225-0312 | [1] | FILM-WARNING (JUMP START, READ OMM, INTL) | ||
| (INSIDE OF BATTERY BOX DOOR CENTERED ABOVE DOOR LATCH & 75 +/-5 UP FROM THE EDGE OF DOOR) | ||||
| 226-1240 | [2] | FILM-WARNING (CRUSH HAZARD, STAY BACK, INTL) | ||
| (ON BOOM 700MM +/-5 UP FROM CENTER LINE OF SWING & BOOM LOWER FOOT PIN & 65MM +/- OVER FROM INSIDE OF THE REAR EDGE OF | ||||
| BOOM WRAPPER PLATE) | ||||
| 239-9430 | [1] | FILM-WARNING (ARM BRACE, READ OMM, INTL) | ||
| (ON LH SIDE OF THE MACHINE ON SAFETY BRACE CENTERED FROM TOP TO BOTTOM & FROM SIDE TO SIDE) | ||||
| 240-7095 | [2] | FILM-WARNING (NO ENTRANCE, EXIT, READ OMM) | ||
| (ON THE REAR OF THE CAB STRUCTURE AT THE BOTTOM 50 +/-5MM FROM THE RED REFLECTOR TOWARD THE CENTER OF THE MACHINE FOR | ||||
| BOTH FILMS, CENTERED FROM TOP TO BOTTOM) | ||||
| 255-0793 | [1] | FILM-WARNING (READ OMM) | ||
| (ON RH CONSOLE UNDER KEYSWITCH IN AREA PROVIDED. UNIVERSAL FILM IS ON THE UPPER HALF | ||||
| & THE SEATBELT IS ON THE LOWER HALF) | ||||
| 255-0794 | [1] | FILM-WARNING (SEAT BELT) | ||
| (ON RH CONSOLE UNDER KEYSWITCH IN AREA PROVIDED. UNIVERSAL FILM IS ON THE UPPER HALF & THE SEATBELT IS ON THE LOWER | ||||
| HALF) | ||||
| 259-4402 | [1] | FILM-WARNING (HOT FLUID UNDER PRESSURE) | ||
| (ON RADIATOR CAP ORIENTED SUCH THAT IT CAN BE READ FROM THE LH SIDE OF THE MACHINE) | ||||
Information:
OPERATOR STATION
WASHER GP-WINDOW
Operation and Maintenance Manual
