6J-9256 TRUNNION GP-BULLDOZER S/N A7H1-UP; A7X1-UP; A7Z1-UP PART OF 274-7283, 282-5957, 293-3119, 316-6844, 316-6845 BULLDOZER AR-ANGLING AN ATTACHMENT D7G

6J-9256 TRUNNION GP-BULLDOZER
S/N A7H1-UP; A7X1-UP; A7Z1-UP
PART OF 274-7283, 282-5957, 293-3119, 316-6844, 316-6845 BULLDOZER AR-ANGLING
AN ATTACHMENT

i03332857 SEBP5047

6J9256 TRUNNION GP-BULLDOZER Parts scheme

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7X-0402	[12]	BOLT (1-8X2-IN)
2.	3B-4516	[12]	LOCKWASHER
3.	6J-9258	[2]	TRUNNION AS
			(EACH INCLUDES)
3A.	5J-4321	[1]	TRUNNION

#SEBP50470251

6W-8505: ADJUSTER GP-SEAT

ADJUSTER GP-SEAT

6W-8505 ADJUSTER GP-SEAT
S/N 7MB5000-5235
PART OF 6W-8502 SUSPENSION GP-SEAT

i03451360 SEBP5047

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	8V-4881	[4]	ROLLER
2.	4V-7860	[1]	LEVER
3.	6W-8506	[1]	HOUSING AS (LOWER)
4.	4V-7850	[1]	PLATE-SLIDE TRACK
5.	4V-7855	[1]	LATCH AS
6.	4V-7881	[1]	ROD-LATCH
7.	4V-8256	[2]	SPRING
8.	013-8289	[1]	BOLT (1/2-13X0.75-IN)
9.	4V-7859	[1]	ROD-LATCH
10.	4V-7857	[1]	LATCH AS
11.	5V-1497	[7]	RETAINER
12.	1B-6182	[1]	SPACER (13.11X19.05X1.18-MM THK)
13.	4V-7865	[1]	CAP

#SEBP50470252

198-7281: BLOWER GP-CAB

BLOWER GP-CAB

198-7281 BLOWER GP-CAB
S/N 7MB5000-UP
PART OF 273-9227 DASH GP

i03298051 SEBP5047

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	1M-1230	[4]	NUT-LOCKING (10-32-THD)
2.	3S-2093	[1]	STRAP-CABLE
3.	6T-6708	[2]	WASHER (7X28.6X4.1-MM THK)
4.	7G-0942	[2]	PLATE-ORIFICE
5.	8C-3756	[1]	FILM-IDENTIFICATION (AIR CONDITIONER)(AIR CONDITIONER, HEATER)
6.	9G-1950	[1]	RESISTOR
7.	111-7198	[1]	HARNESS AS-MOTOR (BLOWER)
8.	174-1504	[1]	MOTOR AS-BLOWER (24-VOLT, A/C, HEATER)
	9W-0852	[2]	PIN-CONNECTOR (14-GA TO 16-GA)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
9.	174-1505	[1]	MOTOR AS-BLOWER (24-VOLT, A/C, HEATER)
	9W-0844	[2]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS, WEDGE, & INTERFACE SEAL)
10.	175-0070	[4]	BRACKET
11.	198-7282	[1]	PLATE AS
12.	198-7284	[1]	GASKET
13.	256-0622	[1]	WHEEL-BLOWER (CCW)
14.	256-0623	[1]	WHEEL-BLOWER (CW)
15.	2V-8260	[1]	GROMMET
16.	130-5300	[2]	CLIP
17.	3E-9865	[7]	LOCKNUT (1/4-20-THD)
18.	4B-4274	[4]	WASHER (5.5X13X1.2-MM THK)
19.	5P-4115	[6]	WASHER-HARD (7.2X19X2-MM THK)
20.	5P-8167	[1]	BOLT (3/8-16X0.625-IN)
21.	5P-9085	[1]	CLIP (LOOP)
22.	6V-1668	[2]	WASHER (6.5X29.1X3-MM THK)
23.	6V-3320	[1]	SCREW-MACHINE (1/4-20X7.5-IN)
24.	8T-4896	[1]	WASHER-HARD (10.2X18.5X2.5-MM THK)

#SEBP50470253

308-5367: CANOPY AR-NON-ROPS

CANOPY AR-NON-ROPS

308-5367 CANOPY AR-NON-ROPS -ROPS
S/N 7MB5000-UP
FORESTRY
AN ATTACHMENT

i03368955 SEBP5047

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Part No	Qty	Parts name
308-3643 Y	[1]	CANOPY GP-NON-ROPS
308-4669 Y	[1]	DASH GP
307-8824 Y	[1]	FLOORPLATE GP
308-3622 Y	[1]	GUARD GP-VANDALISM
308-5517 Y	[1]	INSTRUMENT GP
273-9221 Y	[1]	MOUNTING GP-NON-ROPS
312-3089 Y	[1]	WIRING GP-CHASSIS
310-9839 Y	[1]	WIRING GP-LIGHTING
Y		SEPARATE ILLUSTRATION

#SEBP50470254

308-3643: CANOPY GP-NON-ROPS

CANOPY GP-NON-ROPS

308-3643 CANOPY GP-NON-ROPS
S/N 7MB5000-UP
PART OF 308-5367 CANOPY AR-NON-ROPS
AN ATTACHMENT

i03343487 SEBP5047

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	6V-8928	[1]	HOOK-COAT
2.	9P-7853	[2]	HANDRAIL
3.	239-6709 Y	[1]	MIRROR GP-REAR VIEW (INTERIOR)
4.	308-3644	[1]	CANOPY AS
5.	8T-4179 M	[4]	BOLT (M12X1.75X20-MM)
6.	8T-4223	[4]	WASHER-HARD (13.5X25.5X3-MM THK)
7.	9X-2045 M	[1]	SCREW-TRUSS HEAD (M6X1X20-MM)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP50470255

274-1153: CONTROL GP-HYDRAULIC HAND

CONTROL GP-HYDRAULIC HAND

274-1153 CONTROL GP-HYDRAULIC HAND -BULLDOZER LIFT, TILT
S/N 7MB5000-UP
PART OF 268-0769 HYDRAULIC AR-2 VALVE

i03335096 SEBP5047

2741153 CONTROL GP-HYDRAULIC HAND Parts scheme

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3W-1482	[1]	SHAFT AS
2.	8E-6894	[1]	HANDLE (BULLDOZER CONTROL)
3.	8E-7364	[1]	BOOT
4.	8G-4657	[1]	YOKE
5.	8T-0798	[8]	BEARING-ROLLER
6.	091-1745 B	[3]	WASHER (16.6X24X1.2-MM THK)
7.	102-2913	[1]	FILM-INSTRUCTION (BULLDOZER CONTROL)
8.	271-0675	[1]	SUPPORT AS
9.	271-2532	[1]	SUPPORT AS
10.	271-2554	[1]	SHAFT AS
11.	271-2576	[2]	SHAFT AS
12.	271-2584	[2]	LINK
13.	271-2659	[1]	ROD AS
	271-2660	[1]	ROD
	6V-8186	[2]	NUT-FULL (5/16-24-THD)
	7H-3641	[2]	END-ROD (5/16-24-THD)
14.	271-2661	[1]	ROD AS
	271-2662	[1]	ROD
	1M-1341	[1]	END-YOKE ROD
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
	8X-6167	[1]	ROD END
15.	271-2665	[1]	ROD AS
	271-2666	[1]	ROD
	5J-5315	[2]	ROD END
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
16.	271-3353	[1]	SPACER (16X28X33-MM THK)
17.	272-2729	[1]	PLATE
18.	273-0405	[1]	LEVER AS
19.	273-0406	[1]	LEVER AS
20.	275-1866	[1]	ROD
21.	031-4155	[2]	LOCKNUT (5/16-18-THD)
22.	260-7268	[5]	SPACER (18X30X25-MM THK)
23.	1B-8704	[1]	KEY-WOODRUFF
24.	2L-6267	[2]	LOCKNUT (3/8-24-THD)
25.	3B-4615	[4]	PIN-COTTER
26.	3W-1492	[1]	LEVER
27.	4L-9337	[1]	BOLT (3/8-16X1.5-IN)
28.	5P-4116	[2]	WASHER-HARD (8.8X20.5X2-MM THK)
29.	5P-8167	[1]	BOLT (3/8-16X0.625-IN)
30.	6B-1225	[2]	PIN
31.	6V-8801	[1]	NUT (3/8-16-THD)
32.	6V-8918	[2]	BOLT (5/16-18X1.25-IN)
33.	7X-3374	[2]	NUT-FULL (1/2-20-THD)
34.	8B-1419	[2]	PIN-CLEVIS
35.	8T-0741	[8]	SEAL-LIP TYPE
36.	8T-4121	[14]	WASHER-HARD (11X21X2.5-MM THK)
37.	8T-4122	[5]	WASHER-HARD (17X32X3.5-MM THK)
38.	8T-4137 M	[2]	BOLT (M10X1.5X20-MM)
39.	8T-4191 M	[4]	BOLT (M10X1.5X16-MM)
40.	8T-4196 M	[10]	BOLT (M10X1.5X35-MM)
41.	8T-4223	[2]	WASHER-HARD (13.5X25.5X3-MM THK)
42.	8T-4224	[2]	WASHER-HARD (8.8X16X2-MM THK)
43.	8T-4896	[5]	WASHER-HARD (10.2X18.5X2.5-MM THK)
	B		USE AS REQUIRED
	M		METRIC PART

#SEBP50470256

274-1154: CONTROL GP-HYDRAULIC HAND

CONTROL GP-HYDRAULIC HAND

274-1154 CONTROL GP-HYDRAULIC HAND -BULLDOZER LIFT
S/N 7MB5000-UP
PART OF 268-0768 HYDRAULIC AR-1 VALVE
AN ATTACHMENT

i03330700 SEBP5047

2741154 CONTROL GP-HYDRAULIC HAND Parts scheme

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3W-1482	[1]	SHAFT AS
2.	8E-6894	[1]	HANDLE (BULLDOZER CONTROL)
3.	8E-7364	[1]	BOOT
4.	8G-4657	[1]	YOKE
5.	8T-0798	[4]	BEARING-ROLLER
6.	091-1745 B	[2]	WASHER (16.6X24X1.2-MM THK)
7.	133-8057	[1]	FILM-INSTRUCTION (BULLDOZER CONTROL)
8.	271-0675	[1]	SUPPORT AS
9.	271-2576	[1]	SHAFT AS
10.	271-2661	[1]	ROD AS
	271-2662	[1]	ROD
	1M-1341	[1]	END-YOKE ROD
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
	8X-6167	[1]	ROD END
11.	271-2665	[1]	ROD AS
	271-2666	[1]	ROD
	5J-5315	[2]	ROD END
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
12.	272-2729	[1]	PLATE
13.	273-0405	[1]	LEVER AS
14.	274-1772	[1]	SUPPORT AS
15.	275-1866	[1]	ROD
16.	260-7268	[4]	SPACER (18X30X25-MM THK)
17.	2L-6267	[2]	LOCKNUT (3/8-24-THD)
18.	3B-4615	[2]	PIN-COTTER
19.	5P-8167	[1]	BOLT (3/8-16X0.625-IN)
20.	6B-1225	[1]	PIN
21.	7X-3374	[2]	NUT-FULL (1/2-20-THD)
22.	8B-1419	[1]	PIN-CLEVIS
23.	8T-0741	[4]	SEAL-LIP TYPE
24.	8T-4121	[13]	WASHER-HARD (11X21X2.5-MM THK)
25.	8T-4122	[1]	WASHER-HARD (17X32X3.5-MM THK)
26.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
27.	8T-4191 M	[4]	BOLT (M10X1.5X16-MM)
28.	8T-4196 M	[10]	BOLT (M10X1.5X35-MM)
29.	8T-4896	[4]	WASHER-HARD (10.2X18.5X2.5-MM THK)
	B		USE AS REQUIRED
	M		METRIC PART

#SEBP50470257

274-1155: CONTROL GP-HYDRAULIC HAND

CONTROL GP-HYDRAULIC HAND

274-1155 CONTROL GP-HYDRAULIC HAND -BULLDOZER, RIPPER
S/N 7MB5000-UP
PART OF 268-0770 HYDRAULIC AR-2 VALVE
AN ATTACHMENT

i03332504 SEBP5047

2741155 CONTROL GP-HYDRAULIC HAND Parts scheme

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	260-7268	[2]	SPACER (18X30X25-MM THK)
2.	3W-1482	[2]	SHAFT AS
3.	8E-6894	[1]	HANDLE (BULLDOZER)
4.	8E-7364	[2]	BOOT
5.	8G-4657	[2]	YOKE
6.	8T-0798	[8]	BEARING-ROLLER
7.	091-1745 B	[2]	WASHER (16.6X24X1.2-MM THK)
8.	133-8056	[1]	FILM-INSTRUCTION (BULLDOZER, RIPPER)
9.	228-0952	[1]	PLATE AS
10.	271-0675	[1]	SUPPORT AS
11.	271-2576	[1]	SHAFT AS
12.	271-2661	[1]	ROD AS
	8X-6167	[1]	ROD END
	1M-1341	[1]	END-YOKE ROD
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
13.	271-2663	[1]	ROD AS
	271-2664	[1]	ROD
	8X-6167	[1]	ROD END
	2K-0400	[1]	END-YOKE ROD
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
14.	271-2665	[1]	ROD AS
	271-2662	[1]	ROD
	5J-5315	[2]	ROD END
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
15.	272-2729	[2]	PLATE
16.	273-0405	[1]	LEVER AS
17.	274-1772	[1]	SUPPORT AS
18.	275-1866	[1]	ROD
19.	275-1867	[1]	ROD
20.	293-9677	[1]	ROD AS
	271-2662	[1]	ROD
	4D-4064	[2]	ROD END (3/8-24-THD)
	6V-8183	[2]	NUT-FULL (3/8-24-THD)
21.	293-9678	[1]	LEVER AS
22.	2A-1736	[1]	HANDLE (RIPPER)
23.	2K-4973	[2]	LOCKNUT (3/8-16-THD)
24.	2L-6267	[2]	LOCKNUT (3/8-24-THD)
25.	3B-4615	[4]	PIN-COTTER
26.	5P-8167	[2]	BOLT (3/8-16X0.625-IN)
27.	5S-7382	[2]	BOLT (3/8-16X1.375-IN)
28.	6B-1225	[2]	PIN
29.	7X-3374	[3]	NUT-FULL (1/2-20-THD)
30.	8B-1419	[2]	PIN-CLEVIS
31.	8T-0741	[8]	SEAL-LIP TYPE
32.	8T-4121	[21]	WASHER-HARD (11X21X2.5-MM THK)
33.	8T-4122	[1]	WASHER-HARD (17X32X3.5-MM THK)
34.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
35.	8T-4191 M	[8]	BOLT (M10X1.5X16-MM)
36.	8T-4195 M	[4]	BOLT (M10X1.5X30-MM)
37.	8T-4196 M	[10]	BOLT (M10X1.5X35-MM)
38.	8T-4896	[7]	WASHER-HARD (10.2X18.5X2.5-MM THK)
	B		USE AS REQUIRED
	M		METRIC PART

#SEBP50470258

270-5420: CONTROL GP-TRANSMISSION

CONTROL GP-TRANSMISSION

270-5420 CONTROL GP-TRANSMISSION
S/N 7MB5000-UP
PART OF 273-3624 POWER TRAIN AR

i03352801 SEBP5047

2705420 CONTROL GP-TRANSMISSION Parts scheme

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	2M-7167	[1]	SPACER (0.502X0.9975X1.01-IN)
2.	2P-3980	[1]	LEVER
3.	3P-7649	[1]	LEVER
4.	4D-4064	[4]	ROD END (3/8-24-THD)
5.	4M-0496	[1]	BOLT (3/8-16X1.75-IN)
6.	4M-1743	[1]	LEVER-CONTROL
7.	4M-6013	[1]	WASHER (22.5X45X5-MM THK)
8.	5Y-1628	[1]	SLEEVE
9.	6V-8801	[6]	NUT (3/8-16-THD)
10.	7F-0192	[1]	BOLT (3/8-16X2-IN)
11.	7M-0706	[1]	KNOB (TRANSMISSION CONTROL)
12.	7P-4190	[2]	BEARING-ROLLER
13.	8B-4037	[1]	WASHER (0.766X1.75X0.083-IN THK)
14.	9S-9365	[1]	BRACKET
15.	270-5422	[1]	LEVER AS
	270-5423	[1]	LEVER AS
15A.	5H-3895	[1]	BUSHING-TERMINAL
16.	270-6143	[1]	ROD
17.	270-6144	[1]	ROD
18.	270-6146	[1]	SHAFT AS
19.	0S-1585	[3]	BOLT (1/2-13X1.5-IN)
20.	1A-1460	[1]	BOLT (1/2-13X2-IN)
21.	1B-8706	[3]	KEY-WOODRUFF
22.	1K-0485	[2]	WASHER (19.4X34.9X2.5-MM THK)
23.	1K-6872	[1]	LOCKNUT (1/2-13-THD)
24.	1L-9062	[1]	BOLT (3/8-24X1.5-IN)
25.	5P-8245	[3]	WASHER-HARD (13.5X25.5X3-MM THK)
26.	5S-7382	[3]	BOLT (3/8-16X1.375-IN)
27.	6V-8183	[1]	NUT-FULL (3/8-24-THD)
28.	7X-0288	[1]	BOLT (3/8-16X1.625-IN)
29.	8T-4896	[4]	WASHER-HARD (10.2X18.5X2.5-MM THK)
30.	9L-7712	[4]	NUT (3/8-24-THD)

#SEBP50470259

274-9754: COVER GP-ACCESS

COVER GP-ACCESS

274-9754 COVER GP-ACCESS -SEAT SUPPORT
S/N 7MB5000-UP
PART OF 273-9223 SUPPORT GP-SEAT

i03358922 SEBP5047

For full view, you need register

Parts for your D7G TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3P-9900	[2]	WASHER (10.5X30X3-MM THK)
2.	4B-4909	[2]	SPRING
3.	246-2641	[1]	PADLOCK GP
	5P-8500	[1]	KEY
4.	8T-9496	[4]	LOCKNUT (9/16-18-THD)
5.	8Y-4000	[2]	LATCH AS (T-BAR, COMPARTMENT)
6.	132-4354	[2]	SPACER (10.5X19X26.5-MM THK)
7.	178-2593	[2]	BUMPER
8.	274-9642	[1]	COVER AS (RH)
9.	274-9738	[1]	COVER AS (LH)
10.	287-8488	[2]	ROD AS
11.	2K-5986	[2]	PIN-SPRING
12.	3V-0613	[6]	BUMPER
13.	3W-9207	[2]	GUIDE
14.	3W-9208	[2]	PAWL
15.	5C-7261 M	[2]	NUT (M8X1.25-THD)
16.	5P-4116	[2]	WASHER-HARD (8.8X20.5X2-MM THK)
17.	6V-7744 M	[4]	LOCKNUT (M10X1.5-THD)
18.	7X-7729	[22]	WASHER (11X25X3-MM THK)
19.	8C-8585 M	[12]	SCREW-BUTTON HEAD (M10X1.5X20-MM)
20.	8E-4832	[2]	STRIKER
21.	8T-4133 M	[4]	NUT (M10X1.5-THD)
22.	8T-4136 M	[4]	BOLT (M10X1.5X25-MM)
23.	8T-4137 M	[10]	BOLT (M10X1.5X20-MM)
24.	8T-4182 M	[2]	BOLT (M10X1.5X45-MM)
25.	8T-4186 M	[4]	BOLT (M10X1.5X40-MM)
26.	8T-4994	[2]	WASHER-HARD (20X36.5X3.5-MM THK)
27.	9W-8940	[2]	PLATE
	M		METRIC PART