WORK TOOLS
CONVEYOR GPSERVICE EQUIPMENT AND SUPPLIES
AIR COMPRESSOR & MOUNTING GPCHARTS & FILMS
TOOLS
WORK TOOLS
CONVEYOR GP
#SEBP51110400
233-5535: MOUNTING GP-CONVEYOR
233-5535 MOUNTING GP-CONVEYOR
S/N RSB1-UP
PART OF 325-1818 CONVERSION GP-MACHINE
AN ATTACHMENT
S/N RSB1-UP
PART OF 325-1818 CONVERSION GP-MACHINE
AN ATTACHMENT
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS#SEBP51110401
241-2500: AIR COMPRESSOR & MOUNTING GP
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9M-3835 | [1] | LATCH-RUBBER | |
| 2. | 237-3842 | [1] | AIR COMPRESSOR | |
| 3. | 2M-5795 | [1] | PIN-CLEVIS | |
| 4. | 241-2493 | [1] | COUPLER | |
| 5. | 241-2496 | [1] | BOX GP-CONTROL | |
| 6. | 241-2497 | [1] | DOOR AS | |
| 7. | 004-7617 | [2] | ELBOW-PIPE | |
| 8. | 245-6300 | [1] | CABLE AS-BATTERY | |
| 9. | 3B-4610 | [1] | PIN-COTTER | |
| 10. | 5P-8998 | [1] | FITTING | |
| 11. | 6V-7743 M | [4] | LOCKNUT (M6X1-THD) | |
| 12. | 6V-7744 M | [2] | LOCKNUT (M10X1.5-THD) | |
| 13. | 7X-7729 | [9] | WASHER (11X25X3-MM THK) | |
| 14. | 8T-4136 M | [5] | BOLT (M10X1.5X25-MM) | |
| 15. | 8T-4195 M | [2] | BOLT (M10X1.5X30-MM) | |
| 16. | 8T-4205 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 145-9123 F | [1] | FILM-WARNING (CABLE CONNECTION) | ||
| (INSIDE OF BATTERY BOX REAR WALL) | ||||
| F | NOT SHOWN | |||
| M | METRIC PART | |||
#SEBP51110402
325-1825: FILM GP-U.S.
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 159-3590 | [1] | FILM-IDENTIFICATION (WATER SEPARATOR) | ||
| (TO RIGHT OF FUEL WATER SEPERATOR BOWL ON REAR COOLING STRUCTURE) | ||||
| 146-6747 | [2] | FILM-INFORMATION (24-VOLT) | ||
| (ON INSIDE OF BATTERY BOX ON FRONT SIDE PLANT NEAR TOP) | ||||
| 224-9855 | [1] | FILM-INSTRUCTION (START AID, READ OMM) | ||
| (ON BRACKET ON RH 'B' POST INSIDE OF CAB) | ||||
| 276-2604 | [1] | FILM-INSTRUCTION (BELT ROUTING) | ||
| (60-MM INWARD FROM LEFT SIDE OF REAR STRUCTURE & 290-MM UP FROM NON-METALLIC MAT - PLACE ON SURFACE FACING REAR OF | ||||
| MACHINE WITHIN RADIATOR STRUCTURE TO LEFT OF LEFT SIDE REMOVABLE ACCESS PANEL & BELOW HOSE GROMMET) | ||||
| 219-0302 | [1] | FILM-WARNING (NO WELD, NO DRILL, READ OMM) | ||
| (ON LH 'B' POST INSIDE OF CAB - FLUSH WITH PARKING BRAKE CONSOLE) | ||||
| 224-7830 | [1] | FILM-WARNING (HIGH PRESSURE, READ OMM, U.S.) | ||
| (ON RH SIDE OF ENGINE END FRAME - ON CAB POST MOUNT - CENTERED BELOW WINDOW) | ||||
| 224-8945 | [2] | FILM-WARNING (DO NOT USE ETHER, U.S.) | ||
| (ONE FILM ON BRACKET ON RH 'B' POST INSIDE CAB) | ||||
| (ONE FILM ON RH SIDE OF ENGINE COMPARTMENT HOOD NEAR PRE-AIRCLEANER, ORIENTATE TO READ FROM RH SIDE PLATFORM) | ||||
| 225-0313 | [2] | FILM-WARNING (JUMP START, READ OMM, U.S.) | ||
| (ON INSIDE OF BATTERY BOX ON FRONT SIDE PLANT NEAR TOP) | ||||
| 225-4256 | [1] | FILM-WARNING (HOT FLUID UNDER PRESSURE, U.S.) | ||
| (ON UNDERSIDE OF SHUNT TANK ACCESS DOOR - ORIENT TO BE READ FROM RH SIDE OF MACHINE) | ||||
| 226-1242 | [2] | FILM-WARNING (CRUSH HAZARD, STAY BACK, U.S.) | ||
| (5-MM ABOVE BOTTOM EDGE OF BLACK PLATE OF CAB & CENTER BETWEEN FRONT CAB SKIRT MOUNTING BOLTS) | ||||
| 240-7956 | [1] | FILM-WARNING (DO NOT OPERATE, READ OMM) | ||
| (ON BRACKET ON RH 'B' POST INSIDE OF CAB) | ||||
| 243-1936 | [1] | FILM-WARNING (SEAT BELT) | ||
| (ON RH 'A' POST INSIDE OF CAB - FLUSH WITH TOP OF STEERING WHEEL FACING OPERATOR) | ||||
| [1] | FILM-WARNING (HIGH PRESSURE CYLINDER) | |||
| (ONE FILM VERTICALLY ON AIR CLEANER BRACKET BETWEEN HARDWARE ON RH SIDE OF MACHINE ADJACENT TO BRAKE ACCUMULATORS) | ||||
| 226-1275 | [1] | FILM-WARNING (CRUSH HAZARD, READ OMM, U.S.) | ||
| (30-MM UP FROM ARTICULATION LOCK PLATE & 150-MM FROM FRONT EDGE OF ENGINE END FRAME) | ||||
#SEBP51110403
445-9509: PARTS GP-MISCELLANEOUS
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 288-4641 | [1] | BELT-SERPENTINE | ||
| 256-7902 | [4] | FILTER ELEMENT AS-AIR (PRIMARY) | ||
| 256-7903 | [4] | FILTER ELEMENT AS-AIR (SECONDARY) | ||
| 111-8738 | [4] | FILTER ELEMENT-CAB AIR | ||
| 180-7487 | [4] | FILTER ELEMENT-CAB AIR (ACTIVATED CHARCOAL) | ||
| 299-8229 | [4] | FILTER ELEMENT-FUEL (ULTRA HIGH EFFICIENCY) | ||
| 423-8525 | [2] | FILTER GP-WATER SEP & FUEL | ||
| 462-1171 | [2] | FILTER-ENGINE OIL (LUBRICATION) | ||
| 1G-8878 | [2] | FILTER-OIL (ADVANCED EFFICIENCY) | ||
| 126-1818 | [1] | FILTER-OIL (ULTRA HIGH EFFICIENCY) |
#SEBP51110404
324-5203: PLATE & FILM GP
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 225-4150 | [1] | PLATE-SERVICE INFORMATION (MACHINE) | ||
| (ADHERE TO COMBO PIN PLATE) | ||||
| 239-6989 | [1] | PLATE-SERIAL NUMBER (MACHINE) | ||
| (ON LH SIDE OF NON-ENGINE END FRAME (OUTSIDE)175-MM FROM TOP OF BOTTOM HITCH PLATE & WITHIN 50-MM OF VERTICAL EDGE OF | ||||
| TOWER) | ||||
| 193-5913 B | [8] | PLUG | ||
| 193-5914 B | [39] | PLUG | ||
| 193-5918 B | [4] | PLUG | ||
| 7X-3229 | [4] | FILM-IDENTIFICATION (LIFT EYE, TIE-DOWN LOCATION) | ||
| (ABOVE EACH TIE DOWN EYE-CENTERED ON HOLE ON ENGINE END FRAME OR COUNTERWEIGHT (IF FITTED) & ADJACENT TO EACH EYE | ||||
| TOWARD INSIDE OF NON-ENGINE END FRAME) | ||||
| 134-7258 | [1] | FILM-INFORMATION (EXTENDED LIFE COOLANT) | ||
| (ON UNDERSIDE OF SHUNT TANK ACCESS DOOR, ORIENT TO BE READ FROM RH SIDE OF MACHINE) | ||||
| 220-5566 | [1] | FILM-IDENTIFICATION (GREASE POINT) | ||
| (ON GREASE BLOCK ON ENGINE END FRAME) | ||||
| 220-5567 | [1] | FILM-INFORMATION (GREASE POINT) | ||
| (ON GREASE BLOCK ON NON-ENGINE END FRAME) | ||||
| 220-5574 | [1] | FILM-INSTRUCTION (RADIATOR DOOR) | ||
| (ON FAN GUARD BELOW LATCH, POSITION SO THAT IT IS COVERED WHEN SERVICE DOOR IS CLOSED) | ||||
| 220-5738 | [1] | FILM-IDENTIFICATION (GREASE POINTS) | ||
| (ON LEFT FRONT CAB SKIRT AS CLOSE TO BEND AS POSSIBLE WITHOUT CROSSING BEND & CENTERED VERTICALLY) | ||||
| 297-5493 | [1] | FILM-ROPS (OPS, READ OMM) | ||
| (ON LH 'B' POST INSIDE OF CAB FLUSH WITH TOP OF CONSOLE) | ||||
| 300-9915 | [2] | FILM-IDENTIFICATION (HYDRAULIC OIL) | ||
| (ONE FILM ON TOP OF HYDRAULIC TANK, CENTERED ON SIGHT GAUGE. ORIENT TO BE READ FROM RH SIDE OF MACHINE) | ||||
| (ONE FILM ON RH SIDE OF CAB NEAR BOTTOM & BACK EDGE OF CAB) | ||||
| 309-6899 | [1] | FILM-INSTRUCTION (BATTERY) | ||
| (CENTER OF FRONT GLASS,VISIBLE FROM SEATED POSITION IN CAB. FOR OROPS CAB,PLACE ON LH 'B' POST AT EYE LEVEL OF OPERATOR | ||||
| FROM SEATED POSITION IN CAB) | ||||
| [1] | FILM-INSTRUCTION (DOOR, READ OMM) | |||
| (ON LEFT HAND SIDE OF ENGINE END FRAME (OUTSIDE) IN FRONT OF REAR TIRE) | ||||
| B | USE AS REQUIRED | |||
#SEBP51110405
342-9448: PLATE & FILM GP
342-9448 PLATE & FILM GP -25,370 LBS DRIVE ON WEIGHT
S/N RSB1-UP
TRANSPORT & TIE-DOWN LOCATION
PART OF 341-0128 CONVERSION GP-MACHINE
AN ATTACHMENT
S/N RSB1-UP
TRANSPORT & TIE-DOWN LOCATION
PART OF 341-0128 CONVERSION GP-MACHINE
AN ATTACHMENT
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| NO SERVICED PARTS | ||||
#SEBP51110406
342-9449: PLATE & FILM GP
342-9449 PLATE & FILM GP -25,060 LBS DRIVE ON WEIGHT
S/N RSB1-UP
TRANSPORT & TIE-DOWN LOCATION
PART OF 340-0472 CONVERSION GP-MACHINE
AN ATTACHMENT
S/N RSB1-UP
TRANSPORT & TIE-DOWN LOCATION
PART OF 340-0472 CONVERSION GP-MACHINE
AN ATTACHMENT
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| NO SERVICED PARTS | ||||
#SEBP51110407
233-5536: TOOL GP-HAND
233-5536 TOOL GP-HAND
S/N RSB1-UP
PART OF 325-1818, 340-0472, 341-0128 CONVERSION GP-MACHINE
AN ATTACHMENT
S/N RSB1-UP
PART OF 325-1818, 340-0472, 341-0128 CONVERSION GP-MACHINE
AN ATTACHMENT
For full view, you need register
Parts for your 928H WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 237-3827 | [1] | CONTROL GP-REMOTE (CAB REMOVAL) | ||
| 237-3840 | [1] | MOUNTING GP-STORAGE BOX | ||
| 8T-4121 | [4] | WASHER-HARD (11X21X2.5-MM THK) | ||
| 8T-4133 M | [2] | NUT (M10X1.5-THD) | ||
| 8T-4137 M | [2] | BOLT (M10X1.5X20-MM) | ||
| 240-0362 | [1] | STRAP-NYLON | ||
| 240-0366 | [1] | BRACKET | ||
| 170-2512 | [1] | SWITCH GP-TOGGLE (CAB REMOVAL) | ||
| 6T-3631 | [2] | NUT-HEX (15/32-32-THD) | ||
| 6T-3632 | [1] | LOCKWASHER | ||
| 6T-3633 | [1] | RING-LOCKING | ||
| 186-3735 | [6] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 102-8805 | [1] | KIT-RECEPTACLE (6-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 239-2296 | [1] | ADAPTER AS-TORQUE WRENCH | ||
| 262-2759 | [1] | WRENCH-TORQUE | ||
| 6V-4170 | [1] | ADAPTER | ||
| 6V-3146 | [1] | EXTENSION | ||
| 236-4810 | [1] | BLOCK AS | ||
| 8H-8548 | [1] | EXTENSION AS (3/4-IN DRIVE) | ||
| 325-5713 | [1] | HARNESS AS-LIGHTING (JUMPER) | ||
| 8T-8737 | [29] | PLUG-SEAL | ||
| 125-7875 E | TUBE-HEAT SHRINK (7.44-MM DIA)(10-CM) | |||
| 155-2274 | [1] | KIT-CONNECTING PLUG (6-PIN) | ||
| (INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 167-3692 | [1] | RECEPTACLE AS-CONNECTOR (31-PIN) | ||
| 180-9339 | [4] | PIN-CONNECTOR (14-GA TO 18-GA) | ||
| 180-9340 | [4] | SOCKET-CONNECTOR (14-GA TO 18-GA) | ||
| 167-3693 | [1] | PLUG AS-CONNECTOR (31-PIN) | ||
| 8T-7929 M | [4] | BOLT (M12X1.75X180-MM) | ||
| 4C-8359 M | [1] | EYEBOLT (M12X1.75X82-MM) | ||
| 155-2255 | [1] | KIT-CONNECTING PLUG (12-PIN) | ||
| 155-2270 | [1] | KIT-CONNECTING PLUG (2-PIN) | ||
| 155-2274 | [1] | KIT-CONNECTING PLUG (6-PIN) | ||
| (EACH PLUG KIT INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| 102-8805 | [1] | KIT-RECEPTACLE (6-PIN) | ||
| 102-8801 | [1] | KIT-RECEPTACLE (12-PIN) | ||
| (EACH RECEPTACLE KIT INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 237-4968 | [2] | PIN (GUIDE) | ||
| 8T-8737 | [71] | PLUG-SEAL | ||
| 1U-8238 | [1] | SLING-LIFTING | ||
| 9U-6533 | [1] | SOCKET | ||
| 9U-6539 | [1] | SOCKET | ||
| 240-0362 | [1] | STRAP-NYLON | ||
| 239-2297 | [1] | TOOL BOX | ||
| 8T-4223 | [4] | WASHER-HARD (13.5X25.5X3-MM THK) | ||
| 6V-9104 | [1] | WRENCH (30-MM) | ||
| 162-8718 J | [1] | WRENCH-TORQUE | ||
| AVAILABLE REPAIR KIT(S): | ||||
| 160-6390 J | [1] | KIT-REPAIR (TORQUE WRENCH) | ||
| (INCLUDES GEAR, PAWL, SEALS, WASHER, SPRING, SCREWS, INSTRUCTION MANUAL, REVERSE LEVER, 0-RING & BALL) | ||||
| E | ORDER BY THE CENTIMETER | |||
| J | KIT MARKED J SERVICES PART(S) MARKED J | |||
| M | METRIC PART | |||
