251-0432 WIRING GP-CAB S/N LAL364-UP PART OF 229-9072 OPERATOR AR 325D L EXCAVATOR

ELECTRICAL AND STARTING SYSTEM

WIRING GP

0. 251-0432 WIRING GP-
1. 251-0613 WIRING GP-
2. 259-5118 WIRING GP-
3. 267-7642 WIRING GP-
4. 291-7459 WIRING GP-
5. 267-7751 WIRING GP-
6. 267-7752 WIRING GP-
7. 267-7752 WIRING GP-
8. 231-1836 WIRING GP-
9. 251-0433 WIRING GP-
0. INFORMATION

EXCAVATOR 325D L EXCAVATOR LAL
325D L Excavator LAL00001-UP (MACHINE) POWERED BY C7 Engine SEBP5222 325D L LAL (2007)

ELECTRICAL AND STARTING SYSTEM

WIRING GP

251-0439 WIRING GP-BOOM FLOAT

251-0432 WIRING GP-CAB

251-0613 WIRING GP-CAB

259-5118 WIRING GP-CAB

267-7642 WIRING GP-CAB

#SEBP52220270

251-0432: WIRING GP-CAB

WIRING GP-CAB

251-0432 WIRING GP-CAB
S/N LAL364-UP
PART OF 229-9072 OPERATOR AR

i03112520 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[5]	STRAP-CABLE
2.	6C-9058 M	[1]	SCREW (M6X1X12-MM)
3.	6C-9081	[2]	LOCKWASHER
4.	6C-9121	[1]	BRACKET AS-LAMP
5.	6C-9122	[2]	LAMP (24-VOLT)(DOME LIGHT)
6.	7K-1181	[14]	STRAP-CABLE
7.	102-8016	[1]	RESISTOR AS (BACKUP)(BACKUP)
8.	113-8490	[21]	FUSE (10-AMPERE)
9.	113-8491	[6]	FUSE (15-AMPERE)
10.	113-8493	[3]	FUSE (25-AMPERE)
11.	120-4779	[8]	HOOK
12.	132-1829 Y	[1]	ALARM GP (24-VOLT)(FAULT)
13.	141-2759	[8]	FUSE (5-AMPERE)
14.	161-3128	[1]	RELAY (24-VOLT)(BOOM FLOODLIGHT)
14A.	161-3128	[1]	RELAY (24-VOLT)(CHASSIS LIGHT)
14B.	161-3128	[1]	RELAY (24-VOLT)(CAB FLOODLIGHT)
14C.	161-3128	[1]	RELAY (24-VOLT)(HORN)
14D.	161-3128	[1]	RELAY (24-VOLT)(NEUTRAL START)
14E.	161-3128	[1]	RELAY (24-VOLT)(TRAVEL ALARM)
14F.	161-3128	[1]	RELAY (24-VOLT)(ETHER)
15.	268-1964	[1]	KIT-SERVICE METER
			(INCLUDES METER & FILM)
16.	163-6758	[1]	WIRE AS
17.	167-3593	[1]	STRAP
18.	170-6888	[1]	PULLER-FUSE
19.	328-0651 C	[1]	CONTROL GP-WIPER
20.	213-0772	[1]	SWITCH AS-MAGNETIC (24-VOLT)(MAIN RELAY)
21.	220-6420	[8]	SCREW
22.	227-7575	[1]	PANEL-CONTROL (SWITCH)
23.	234-1097	[1]	BRACKET
24.	238-2212	[1]	SWITCH AS-ROCKER (FINE SWING)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[1]	TERMINAL (MALE)
25.	238-2318	[1]	LIGHTER AS-CIGAR (24-VOLT)
26.	238-2390	[1]	CABLE AS (RED)
	6V-2369 D		CABLE (4-GA, BLACK)(0.3-M)
	9G-4343	[2]	TERMINAL-RING (4-GA, 1/4-IN SCREW)
	125-7876 BE		TUBE-HEAT SHRINK (17.78-MM DIA)
27.	238-2391	[1]	CABLE AS (PURPLE)
	6V-2369 D		CABLE (4-GA, BLACK)(0.3-M)
	9G-4343	[2]	TERMINAL-RING (4-GA, 1/4-IN SCREW)
	125-7876 BE		TUBE-HEAT SHRINK (17.78-MM DIA)
28.	251-0637	[1]	INSULATION
29.	275-8651	[1]	HARNESS AS-CAB
	102-8803	[3]	KIT-RECEPTACLE (3-PIN)
			(EACH INCLUDES RECEPTACLE AS & WEDGE)
	186-3735	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
	8T-8730	[6]	SOCKET-CONNECTOR (16-GA TO 18-GA)
	3S-2093	[110]	STRAP-CABLE
	6T-6506	[2]	TERMINAL-BLADE (14-GA TO 18-GA)
	7Y-3951	[6]	TERMINAL-BLADE (14-GA)
	7Y-3952	[3]	PLUG-CONNECTOR (2-PIN)
	7Y-3962	[1]	TERMINAL-BULLET (MALE)
	7Y-3963	[1]	TERMINAL-BULLET (FEMALE)
	8C-6354	[1]	CAP-RECEPTACLE (ET CONNECTOR)
	8T-8737	[33]	PLUG-SEAL
	5P-6271	[1]	CONNECTOR AS
	9W-1951	[1]	RECEPTACLE-CONNECTOR (9-PIN)
	102-7964	[2]	PLUG-CONNECTOR (16-PIN)
	102-7965	[68]	TERMINAL (FEMALE)
	9W-0844	[3]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	116-0255	[1]	TERMINAL-BLADE (10-GA TO 20-GA)
	119-3662 BE		TUBE-HEAT SHRINK (10.85-MM DIA)
	121-1022	[2]	DIODE
	121-1168	[1]	CONNECTOR-RECEPTACLE
	121-1173	[13]	TERMINAL (MALE)
	125-4841	[2]	WEDGE-PLUG LOCK (21-PIN)
	125-7874 BE		TUBE-HEAT SHRINK (5.72-MM DIA)
	125-7875 BE		TUBE-HEAT SHRINK (7.44-MM DIA)
	9X-3402	[15]	SOCKET-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1768	[15]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	2L-8065	[3]	TERMINAL-RING (10-GA TO 12-GA, NO. 8 SCREW)
	2L-8066	[2]	TERMINAL-RING (10-GA TO 12-GA, NO. 10 SCREW)
	2L-8067	[6]	TERMINAL-RING (10-GA TO 12-GA, 1/4-IN SCREW)
	2L-8075	[2]	TERMINAL-RING (14-GA TO 16-GA, NO. 8 SCREW)
	128-8950	[1]	CONNECTOR-RECEPTACLE
	2L-8075	[5]	TERMINAL-RING (14-GA TO 16-GA, NO. 8 SCREW)
	176-9299	[2]	KIT-RECEPTACLE (3-PIN)
			(EACH INCLUDES RECEPTACLE AS & WEDGE)
	134-3296	[1]	HOUSING-PLUG
	134-3297	[1]	SEAL
	9X-3401	[12]	PIN-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1767	[12]	PIN-CONNECTOR (14-GA TO 16-GA)
	149-5069	[8]	TERMINAL-BLADE (14-GA TO 20-GA)
	149-5070	[16]	TERMINAL-BLADE (16-GA TO 20-GA)
	149-5071	[8]	TERMINAL-BLADE (12-GA TO 14-GA)
	153-2602	[5]	RECEPTACLE-CONNECTOR (1-PIN)
	153-2631	[5]	TERMINAL (FEMALE)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[2]	KIT-CONNECTING PLUG (2-PIN)
			(EACH PLUG KIT INCLUDES PLUG AS, WEDGE, & INTERFACE SEAL)
	163-6659	[1]	CONNECTOR-PLUG (12-PIN)
	163-6699	[1]	CONNECTOR-PLUG (18-PIN)
	163-6790	[23]	TERMINAL (FEMALE)
	163-6803	[6]	PLUG-CONNECTOR (5-PIN)
	167-3487	[6]	WEDGE-PLUG LOCK (5-PIN)
	170-6890	[5]	TERMINAL-BLADE (14-GA)
	170-6891	[22]	TERMINAL-BLADE (16-GA TO 18-GA)
	174-3016	[2]	PLUG AS-CONNECTOR (3-PIN)
	179-9046	[2]	TERMINAL (14-GA TO 20-GA)
	230-4009	[1]	PLUG AS-CONNECTOR (12-PIN)
	264-7034	[1]	SEAL-CONNECTOR
	230-4011	[1]	PLUG AS-CONNECTOR (2-PIN)
	264-7029	[1]	SEAL-CONNECTOR
	230-4013	[1]	PLUG AS-CONNECTOR (3-PIN)
	264-7030	[1]	SEAL-CONNECTOR
	238-2319	[1]	BASE AS (FUSE, RELAY PANEL)
	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
	095-0742 M	[2]	SCREW-MACHINE (M6X1X16-MM)
	170-9394	[40]	TERMINAL
	238-2363	[6]	TERMINAL (FEMALE)
	238-2366	[10]	TERMINAL (MALE)
	239-7356	[1]	PLUG AS-CONNECTOR (12-PIN)
	264-7034	[1]	SEAL-CONNECTOR
	243-4505	[2]	RECEPTACLE AS-CONNECTOR (2-PIN)
	243-4506	[1]	RECEPTACLE AS-CONNECTOR (3-PIN)
30.	096-5962	[3]	WASHER-HARD (3.4X7X0.8-MM THK)
31.	096-6166	[3]	WASHER-HARD (4.5X9X1-MM THK)
32.	124-3548	[2]	FUSE (30-AMPERE)
33.	132-5789	[7]	CLIP (LADDER)
34.	150-6256 M	[3]	BOLT-SOCKET HEAD (M3X0.5X12-MM)
35.	259-5022	[1]	ANTENNA AS
	259-5081	[1]	ROD
	259-5082	[1]	CABLE AS
36.	263-9441	[2]	SPEAKER AS
37.	4P-7581	[1]	CLIP (LADDER)
38.	6C-9198 M	[2]	BOLT (M5X0.8X15-MM)
39.	6V-9672 M	[2]	SCREW-MACHINE (M4X0.7X16-MM)
40.	6V-9673 M	[1]	SCREW-MACHINE (M5X0.8X12-MM)
41.	8T-0328	[3]	WASHER-HARD (5.5X10X1-MM THK)
42.	8T-0337 M	[1]	SCREW-MACHINE (M4X0.7X12-MM)
43.	8T-4127 M	[2]	SCREW-MACHINE (M5X0.8X20-MM)
44.	9D-6886	[8]	CLAMP
45.	9X-2042 M	[13]	SCREW-TRUSS HEAD (M6X1X12-MM)
46.	9X-2044 M	[5]	SCREW-TRUSS HEAD (M6X1X16-MM)
47.	9X-8256	[1]	WASHER (6.6X12X2-MM THK)
48.	101-2846 E	[3]	GUARD (9.5-CM EACH)
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP52220271

251-0613: WIRING GP-CAB

WIRING GP-CAB

251-0613 WIRING GP-CAB -BOOM FLOAT
S/N LAL1-UP
PART OF 247-7391 CONTROL AR-BOOM
AN ATTACHMENT

i02389061 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7K-1181	[14]	STRAP-CABLE
2.	149-5050	[1]	RELAY (24-VOLT)(BOOM FLOAT, DISABLE)
2A.	149-5050	[1]	RELAY (24-VOLT)(SMARTBOOM, DOWN)
2B.	149-5050	[1]	RELAY (24-VOLT)(SMARTBOOM, UP/DOWN)
3.	238-2214	[1]	SWITCH AS-ROCKER (BOOM FLOAT)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[5]	TERMINAL (MALE)
4.	238-2215	[1]	SWITCH AS-ROCKER (OVERLOAD WARNING)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
	167-3543	[4]	TERMINAL (MALE)
5.	251-0614	[1]	HARNESS AS-SENSOR (BOOM FLOAT)
	8T-8730	[7]	SOCKET-CONNECTOR (16-GA TO 18-GA)
	3S-2093	[27]	STRAP-CABLE
	7Y-3962	[1]	TERMINAL-BULLET (MALE)
	8T-8737	[1]	PLUG-SEAL
	125-7874 BE		TUBE-HEAT SHRINK (5.72-MM DIA)
	9X-3402	[3]	SOCKET-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1768	[3]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	9X-3401	[4]	PIN-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1767	[4]	PIN-CONNECTOR (14-GA TO 16-GA)
	149-5051	[3]	CONNECTOR-RECEPTACLE
	149-5069	[5]	TERMINAL-BLADE (14-GA TO 20-GA)
	149-5070	[8]	TERMINAL-BLADE (16-GA TO 20-GA)
	230-4013	[1]	PLUG AS-CONNECTOR (3-PIN)
	264-7030	[1]	SEAL-CONNECTOR
	230-5008	[2]	PLUG AS-CONNECTOR (4-PIN)
			(EACH INCLUDES)
	264-7031	[1]	SEAL-CONNECTOR
	243-4507	[1]	RECEPTACLE AS-CONNECTOR (4-PIN)
6.	5C-2890 M	[3]	NUT (M6X1-THD)
7.	9X-8256	[3]	WASHER (6.6X12X2-MM THK)
	B		USE AS REQUIRED
	E		ORDER BY THE CENTIMETER
	M		METRIC PART

#SEBP52220272

259-5118: WIRING GP-CAB

WIRING GP-CAB

259-5118 WIRING GP-CAB -PRIMING PUMP
S/N LAL1-UP
PART OF 247-7458 PUMP GP-FUEL PRIMING
AN ATTACHMENT

i02301750 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[5]	STRAP-CABLE
2.	7K-1181	[9]	STRAP-CABLE
3.	149-5050	[1]	RELAY (24-VOLT)(PRIMING PUMP)
4.	259-5119	[1]	HARNESS AS-CAB
	8T-8730	[1]	SOCKET-CONNECTOR (16-GA TO 18-GA)
	3S-2093	[2]	STRAP-CABLE
	8T-8737	[1]	PLUG-SEAL
	9W-0852	[1]	PIN-CONNECTOR (14-GA TO 16-GA)
	9W-0844	[3]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	149-5051	[1]	CONNECTOR-RECEPTACLE
	149-5069	[2]	TERMINAL-BLADE (14-GA TO 20-GA)
	149-5070	[2]	TERMINAL-BLADE (16-GA TO 20-GA)
	170-6891	[1]	TERMINAL-BLADE (16-GA TO 18-GA)
	230-5008	[1]	PLUG AS-CONNECTOR (4-PIN)
	264-7031	[1]	SEAL-CONNECTOR
	243-4505	[1]	RECEPTACLE AS-CONNECTOR (2-PIN)
5.	5C-2890 M	[1]	NUT (M6X1-THD)
6.	9X-8256	[1]	WASHER (6.6X12X2-MM THK)
	M		METRIC PART

#SEBP52220273

267-7642: WIRING GP-CAB

WIRING GP-CAB

267-7642 WIRING GP-CAB -COUPLER
S/N LAL1-UP
PART OF 262-3580 CONTROL AR-COUPLER
AN ATTACHMENT

i02390036 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7K-1181	[13]	STRAP-CABLE
2.	149-5050	[1]	RELAY (24-VOLT)(QUICK COUPLER LOCK PRIORITY)
2A.	149-5050	[1]	RELAY (24-VOLT)(QUICK COUPLER LOCK ON)
2B.	149-5050	[1]	RELAY (24-VOLT)(QUICK COUPLER LOCK)
2C.	149-5050	[1]	RELAY (24-VOLT)(QUICK COUPLER LOCK)
3.	259-4884	[1]	BRACKET AS
4.	259-7220	[1]	COVER
5.	267-7644	[1]	HARNESS AS-QUICK COUPLER
	102-7965	[3]	TERMINAL (FEMALE)
	125-7874 E		TUBE-HEAT SHRINK (5.72-MM DIA)(10-CM)
	125-7875 E		TUBE-HEAT SHRINK (7.44-MM DIA)(15-CM)
	149-5070	[9]	TERMINAL-BLADE (16-GA TO 20-GA)
	163-6803	[1]	PLUG-CONNECTOR (5-PIN)
	230-5008	[1]	PLUG AS-CONNECTOR (4-PIN)
	7Y-3950	[2]	TERMINAL-BLADE (14-GA TO 20-GA)
	7Y-3953	[1]	CONNECTOR-RECEPTACLE
	149-5069	[7]	TERMINAL-BLADE (14-GA TO 20-GA)
	3S-2093	[15]	STRAP-CABLE
	230-5008	[1]	PLUG AS-CONNECTOR (4-PIN)
6.	267-7671	[1]	SWITCH GP-TOGGLE (QUICK COUPLER)
	105-5175	[1]	SWITCH AS-TOGGLE (QUICK COUPLER)
	3L-8187	[6]	LOCKWASHER
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	6V-8374	[6]	SCREW-MACHINE (6-32X0.25-IN)
	267-7672	[1]	HARNESS AS-WIRING
	3S-2093	[1]	STRAP-CABLE
	121-1173	[3]	TERMINAL (MALE)
	167-3542	[1]	RECEPTACLE-CONNECTOR (5-PIN)
7.	267-7676	[1]	BRACKET AS
8.	9X-2042 M	[7]	SCREW-TRUSS HEAD (M6X1X12-MM)
	E		ORDER BY THE CENTIMETER
	M		METRIC PART

#SEBP52220274

291-7459: WIRING GP-CHASSIS

WIRING GP-CHASSIS

291-7459 WIRING GP-CHASSIS -FAN CLUTCH
S/N LAL1-UP
PART OF 251-0448 WIRING GP-FAN
AN ATTACHMENT

i02625584 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[7]	STRAP-CABLE
2.	7K-1181	[5]	STRAP-CABLE
3.	107-8618	[1]	SENSOR GP-TEMPERATURE (AMBIENT AIR, RAD FAN CLUTCH)
	112-4550 E		SLEEVE (31-CM)
	186-3735	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
4.	116-0118	[1]	CLIP
5.	267-8020	[1]	HARNESS AS-CONTROL (FAN CLUTCH)
	3S-2093	[1]	STRAP-CABLE
	8T-8737	[2]	PLUG-SEAL
	125-7874 BE		TUBE-HEAT SHRINK (5.72-MM DIA)
	9X-3402	[8]	SOCKET-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1767	[8]	PIN-CONNECTOR (14-GA TO 16-GA)
	9X-3401	[7]	PIN-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1767	[7]	PIN-CONNECTOR (14-GA TO 16-GA)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
			(INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
	230-5010	[1]	PLUG AS-CONNECTOR (6-PIN)
	264-7032	[1]	SEAL-CONNECTOR
	243-4509	[1]	RECEPTACLE AS-CONNECTOR (8-PIN)
6.	8T-4121	[1]	WASHER-HARD (11X21X2.5-MM THK)
7.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
	B		USE AS REQUIRED
	E		ORDER BY THE CENTIMETER
	M		METRIC PART

#SEBP52220275

267-7751: WIRING GP-COMMUNICATION

WIRING GP-COMMUNICATION

267-7751 WIRING GP-COMMUNICATION -PRODUCT LINK 321SR
S/N LAL1-UP
PART OF 264-8550, 314-3529 INSTALLATION AR-COMMUNICATION
AN ATTACHMENT

i02415015 SEBP5222

2677751 WIRING GP-COMMUNICATION Parts scheme

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[5]	STRAP-CABLE
2.	7K-1181	[3]	STRAP-CABLE
3.	9X-3495	[1]	CLIP AS
4.	111-4837	[1]	CLIP
5.	116-0118	[3]	CLIP
6.	259-4887	[1]	HARNESS AS-WIRING (PRODUCT LINK)
7.	259-4940	[1]	HARNESS AS-WIRING (SERVICE CONNECTOR)
8.	267-7790	[1]	HARNESS AS-CONTROL (PRODUCT LINK, ANTENNA)
9.	8T-5005 M	[1]	BOLT (M10X1.5X70-MM)
10.	132-5789	[1]	CLIP (LADDER)
11.	4I-7889	[1]	SPACER (11X25X45-MM THK)
12.	4P-7581	[2]	CLIP (LADDER)
13.	8T-4121	[4]	WASHER-HARD (11X21X2.5-MM THK)
14.	8T-4136 M	[2]	BOLT (M10X1.5X25-MM)
15.	8T-4137 M	[2]	BOLT (M10X1.5X20-MM)
16.	8T-4191 M	[1]	BOLT (M10X1.5X16-MM)
	M		METRIC PART

#SEBP52220276

267-7752: WIRING GP-COMMUNICATION

WIRING GP-COMMUNICATION

267-7752 WIRING GP-COMMUNICATION -PRODUCT LINK 121SR
S/N LAL1-UP
PART OF 264-8551 INSTALLATION AR-COMMUNICATION
Type 1
AN ATTACHMENT

i02415027 SEBP5222

2677752 WIRING GP-COMMUNICATION Parts scheme

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[5]	STRAP-CABLE
2.	7K-1181	[2]	STRAP-CABLE
3.	9X-3495	[1]	CLIP AS
4.	116-0118	[2]	CLIP
5.	259-4940	[1]	HARNESS AS-WIRING (SERVICE CONNECTOR)
	8T-8732	[1]	RECEPTACLE-CONNECTOR (3-PIN)
	243-4508	[1]	RECEPTACLE AS-CONNECTOR (6-PIN)
6.	267-7790	[1]	HARNESS AS-CONTROL (PRODUCT LINK, ANTENNA)
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	230-5010	[1]	PLUG AS-CONNECTOR (6-PIN)
	243-4508	[1]	RECEPTACLE AS-CONNECTOR (6-PIN)
7.	091-9035	[1]	SPACER (11X25X20-MM THK)
8.	4I-7889	[1]	SPACER (11X25X45-MM THK)
9.	4P-7581	[2]	CLIP (LADDER)
10.	8T-4121	[2]	WASHER-HARD (11X21X2.5-MM THK)
11.	8T-4137 M	[2]	BOLT (M10X1.5X20-MM)
12.	8T-4185 M	[1]	BOLT (M10X1.5X50-MM)
13.	8T-5005 M	[1]	BOLT (M10X1.5X70-MM)
	M		METRIC PART

#SEBP52220277

267-7752: WIRING GP-COMMUNICATION

WIRING GP-COMMUNICATION

267-7752 WIRING GP-COMMUNICATION -PRODUCT LINK 121SR
S/N LAL1-UP
PART OF 264-8551 INSTALLATION AR-COMMUNICATION
Type 2
AN ATTACHMENT

i02919891 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[5]	STRAP-CABLE
2.	7K-1181	[2]	STRAP-CABLE
3.	9X-3495	[1]	CLIP AS
4.	116-0118	[2]	CLIP
5.	259-4940	[1]	HARNESS AS-WIRING (SERVICE CONNECTOR)
6.	267-7790	[1]	HARNESS AS-CONTROL (PRODUCT LINK, ANTENNA)
7.	8T-5005 M	[1]	BOLT (M10X1.5X70-MM)
8.	4I-7889	[1]	SPACER (11X25X45-MM THK)
9.	4P-7581	[2]	CLIP (LADDER)
10.	8T-4121	[2]	WASHER-HARD (11X21X2.5-MM THK)
11.	8T-4137 M	[2]	BOLT (M10X1.5X20-MM)
12.	8T-4136 CM	[1]	BOLT (M10X1.5X25-MM)
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART

#SEBP52220278

231-1836: WIRING GP-CONSOLE

WIRING GP-CONSOLE

231-1836 WIRING GP-CONSOLE -LH
S/N LAL1-UP
PART OF 251-0433 WIRING GP-CONSOLE

i02171878 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[2]	STRAP-CABLE
2.	7K-1181	[1]	STRAP-CABLE
3.	163-6795	[2]	STRAP-CABLE
4.	251-0580	[1]	HARNESS AS-CONSOLE
	8T-8729	[4]	PIN-CONNECTOR (16-GA TO 18-GA)
	8T-8730	[3]	SOCKET-CONNECTOR (16-GA TO 18-GA)
	3S-2093	[9]	STRAP-CABLE
	5P-5995 D		TUBE (0.3-M)
	7Y-3963	[2]	TERMINAL-BULLET (FEMALE)
	7Y-3965	[2]	TUBE (RECEPTACLE TERMINAL)
	8T-8737	[9]	PLUG-SEAL
	9W-0852	[2]	PIN-CONNECTOR (14-GA TO 16-GA)
	9W-0844	[2]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	125-7874 E		TUBE-HEAT SHRINK (5.72-MM DIA)(5-CM)
	125-7875 E		TUBE-HEAT SHRINK (7.44-MM DIA)(5-CM)
	9X-3402	[11]	SOCKET-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1768	[11]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
			(INCLUDES PLUG AS, WEDGE & INTERFACE SEAL)
	230-4011	[1]	PLUG AS-CONNECTOR (2-PIN)
	264-7029	[1]	SEAL-CONNECTOR
	230-5010	[1]	PLUG AS-CONNECTOR (6-PIN)
	264-7032	[1]	SEAL-CONNECTOR
	239-7352	[1]	PLUG AS-CONNECTOR (6-PIN)
	264-7032	[1]	SEAL-CONNECTOR
	243-4505	[1]	RECEPTACLE AS-CONNECTOR (2-PIN)
	243-4508	[1]	RECEPTACLE AS-CONNECTOR (6-PIN)
	247-2693	[1]	RECEPTACLE AS-CONNECTOR (6-PIN)
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER

#SEBP52220279

251-0433: WIRING GP-CONSOLE

WIRING GP-CONSOLE

251-0433 WIRING GP-CONSOLE
S/N LAL1-UP
PART OF 229-9072 OPERATOR AR

i02296150 SEBP5222

For full view, you need register

Parts for your 325D L EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name
231-1836 Y	[1]	WIRING GP-CONSOLE (LH)
251-0435 Y	[1]	WIRING GP-CONSOLE (RH)
Y		SEPARATE ILLUSTRATION

Information:

ELECTRICAL AND STARTING SYSTEM

WIRING GP

Special Instruction

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Tool Operating Manual

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Troubleshooting

CID 0100 FMI 04 Engine Oil Pressure short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0110 FMI 04 Engine Coolant Temperature short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0164 FMI 03 Injector Actuation Pressure voltage high
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0091 FMI 02 Incorrect Throttle Switch inputs
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0617 FMI 05 Air Inlet Heater Relay open/current below normal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0164 FMI 04 Injector Actuation Pressure voltage low
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0100 FMI 10 Engine Oil Pressure Sensor abnormal rate of change
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 1785 FMI 03 Intake Manifold Pressure Sensor voltage high
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 1785 FMI 04 Intake Manifold Pressure Sensor voltage low
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0342 FMI 08 Secondary Engine Speed signal abnormal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0617 FMI 06 Air Inlet Heater Relay grounded/current above norm
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Air Inlet Heater Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0274 FMI 04 Atmospheric Pressure short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 1785 FMI 10 Intake Manifold Pressure Signal abnormal rate of change
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Electrical Connectors - Inspect
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0190 FMI 08 Engine Speed signal abnormal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Fuel Filter Differential Pressure Switch Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0091 FMI 08 Throttle Position signal abnormal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Sensors and Electrical Connectors
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Engine Pressure Sensor Open or Short Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Indicator Lamp Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0324 FMI 06 Warning Lamp short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 0324 FMI 05 Warning Lamp open/short to ground
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 1266 FMI 05 Diagnostic Lamp current below normal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

CID 1266 FMI 06 Diagnostic Lamp current above normal
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Digital Sensor Supply Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Coolant Level Sensor Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Engine Shutdown Switch Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Throttle Position Sensor Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Throttle Switch Circuit - Test
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer

Caterpillar Parts SIS Catalog 325D L :

251-0432 WIRING GP-CAB

251-0439 WIRING GP-BOOM FLOAT

251-0533 WIRING GP-AUXILIARY CONTROL

251-0437 WIRING GP-AUXILIARY CONTROL

251-0441 WIRING GP-AUX START RECEPTACLE

239-1134 VALVE GP-ETHER STARTING

165-5970 SWITCH GP-TOGGLE

251-0613 WIRING GP-CAB

259-5118 WIRING GP-CAB

267-7642 WIRING GP-CAB

291-7459 WIRING GP-CHASSIS

267-7751 WIRING GP-COMMUNICATION

267-7752 WIRING GP-COMMUNICATION

231-1836 WIRING GP-CONSOLE

Truck sale:

62,927

Caterpillar 325DL, Construction
- Crawler Excavators
TOROMONT CAT (QUÉBEC)
Canada

Caterpillar 325DL, Construction
- Crawler Excavators
MANTRAC NIGERIA LIMITED
Nigeria

55,681

Caterpillar 325DL, Construction
- Crawler Excavators
BERGERAT MONNOYEUR S.A.S.
France

129,000

Caterpillar 325DL, Construction
- Crawler Excavators
MICHIGAN CAT

91,600

Caterpillar 325DL, Construction
- Crawler Excavators
ZIEGLER CAT