ELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINEOPERATOR STATION
PANEL GPELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINE
#SEBP54011570
361-0864: CONTROL GP-GENERATOR SET
361-0864 CONTROL GP-GENERATOR SET -EMCP 4.2
S/N YAK1-UP
PART OF 421-8198, 421-8264 PANEL GP-CONTROL
AN ATTACHMENT
S/N YAK1-UP
PART OF 421-8198, 421-8264 PANEL GP-CONTROL
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS#SEBP54011571
503-4411: CONTROL GP-GENERATOR SET
503-4411 CONTROL GP-GENERATOR SET
S/N YAK1-UP
PART OF 351-2428 CONTROL GP-GENERATOR SET
AN ATTACHMENT
S/N YAK1-UP
PART OF 351-2428 CONTROL GP-GENERATOR SET
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 359-0948 | [1] | FILM-INFORMATION (EMCP 4.1/4.2) |
#SEBP54011572
252-7368: CONTROL GP-LOAD SHARE MODULE
252-7368 CONTROL GP-LOAD SHARE MODULE
S/N YAK1-UP
LOW VOLTAGE
Type 1
FOR USE WITH MUI
AN ATTACHMENT
S/N YAK1-UP
LOW VOLTAGE
Type 1
FOR USE WITH MUI
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8C-8514 | [2] | SCREW-MACHINE (8-32X0.375-IN) | |
| 2. | 8T-2882 | [1] | HANDLE-PULL | |
| 3. | 1H-4393 | [2] | LOCKWASHER | |
| 4. | 9X-6772 | [1] | STRAP-CABLE | |
| 5. | 131-5454 | [1] | CONTROL AS-ELECTRONIC GOVERNOR | |
| 6. | 135-6898 | [2] | LATCH AS | |
| 7. | 293-9452 | [1] | MOUNTING-CABLE TIE | |
| 8. | 169-4481 | [2] | HINGE AS | |
| 9. | 235-4451 M | [10] | BOLT-FLANGE HEAD (M6X1X16-MM) | |
| 10. | 242-8835 | [1] | DOOR AS | |
| 11. | 287-7137 | [1] | STRAP AS-GROUND | |
| 2L-8077 | [2] | TERMINAL-RING (14-GA TO 16-GA, 1/4-IN SCREW) | ||
| 12. | 244-9639 Y | [1] | BLOCK AS-TERMINAL | |
| 13. | 244-9642 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 7K-1181 | [1] | STRAP-CABLE | ||
| 109-3038 | [5] | END-WIRE (16-GA) | ||
| 162-4171 | [3] | TERMINAL AS (18-GA TO 20-GA) | ||
| 5P-1475 | [1] | TERMINAL-FORK (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7875 E | TUBE-HEAT SHRINK (7.44-MM DIA)(4-CM) | |||
| 14. | 244-9643 | [1] | HARNESS AS-WIRING (CURRENT TRANSFORMER) | |
| 155-2271 | [1] | KIT-CONNECTING PLUG (4-PIN) | ||
| (INCLUDES PLUG AS & WEDGE) | ||||
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8730 | [4] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 125-9993 | [6] | TERMINAL-FORK (14-GA TO 16-GA, NO. 6 SCREW) | ||
| 15. | 244-9646 | [1] | HARNESS AS-CONTROL (LOAD SHARE) | |
| 7K-1181 | [2] | STRAP-CABLE | ||
| 8T-8729 | [13] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8737 | [57] | PLUG-SEAL | ||
| 125-9997 | [12] | TERMINAL-FORK (16-GA TO 22-GA, NO. 6 SCREW) | ||
| 131-1502 | [1] | TERMINAL AS | ||
| 2L-8075 | [1] | TERMINAL-RING (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7874 E | TUBE-HEAT SHRINK (5.72-MM DIA)(3-CM) | |||
| 133-8753 | [1] | RECEPTACLE AS-CONNECTOR (70-PIN) | ||
| 16. | 245-0074 | [1] | BOX GP-EXTENSION TERMINAL | |
| 6V-9335 D | SEAL (2.1-M) | |||
| 244-9631 J | SEAL (23-DM) | |||
| 244-9669 | [1] | BOX AS | ||
| 17. | 252-7365 Y | [2] | TRANSFORMER GP-POTENTIAL | |
| 18. | 252-7425 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 2L-8081 | [3] | TERMINAL-RING (14-GA TO 16-GA, 1/2-IN SCREW) | ||
| 7K-1181 | [6] | STRAP-CABLE | ||
| 109-3038 | [3] | END-WIRE (16-GA) | ||
| 19. | 252-7519 | [2] | STRAP | |
| 20. | 7I-2273 M | [6] | BOLT (M5X0.8X16-MM) | |
| 21. | 1D-4533 | [2] | BOLT (1/4-20X2.25-IN) | |
| 22. | 3B-4504 | [8] | LOCKWASHER | |
| 23. | 170-5632 M | [4] | BOLT (M4X0.7X16-MM) | |
| 24. | 4D-3100 | [4] | GROMMET | |
| 25. | 5C-2890 M | [13] | NUT (M6X1-THD) | |
| 27. | 5C-9553 M | [2] | BOLT (M6X1X16-MM) | |
| 28. | 5P-0537 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 30. | 9S-8750 | [2] | NUT-FULL (1/4-20-THD) | |
| 31. | 9X-8256 | [6] | WASHER (6.6X12X2-MM THK) | |
| 32. | 4B-4274 | [12] | WASHER (5.5X13X1.2-MM THK) | |
| 33. | 5C-2874 M | [6] | NUT (M5X0.8-THD) | |
| 34. | 7X-0620 | [8] | WASHER-HARD (5.5X13X1.6-MM THK) | |
| 35. | 260-6675 | [4] | NUT-SELF LOCKING (M4X0.7-THD) | |
| 36. | 198-4775 | [2] | WASHER-HARD (6.6X15X6-MM THK) | |
| 37. | 8T-4971 M | [1] | BOLT (M6X1X30-MM) | |
| D | ORDER BY THE METER | |||
| E | ORDER BY THE CENTIMETER | |||
| J | ORDER BY THE DECIMETER | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP54011573
252-7368: CONTROL GP-LOAD SHARE MODULE
252-7368 CONTROL GP-LOAD SHARE MODULE
S/N YAK1-UP
LOW VOLTAGE
Type 2
FOR USE WITH MUI
AN ATTACHMENT
S/N YAK1-UP
LOW VOLTAGE
Type 2
FOR USE WITH MUI
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8C-8514 | [2] | SCREW-MACHINE (8-32X0.375-IN) | |
| 2. | 8T-2882 | [1] | HANDLE-PULL | |
| 3. | 1H-4393 | [2] | LOCKWASHER | |
| 4. | 9X-6772 | [1] | STRAP-CABLE | |
| 5. | 131-5454 | [1] | CONTROL AS-ELECTRONIC GOVERNOR | |
| 6. | 135-6898 | [2] | LATCH AS | |
| 7. | 293-9452 | [1] | MOUNTING-CABLE TIE | |
| 8. | 351-9804 C | [2] | HINGE | |
| 9. | 235-4451 M | [10] | BOLT-FLANGE HEAD (M6X1X16-MM) | |
| 10. | 351-9799 CY | [1] | DOOR AS | |
| 11. | 287-7137 | [1] | STRAP AS-GROUND | |
| 2L-8077 | [2] | TERMINAL-RING (14-GA TO 16-GA, 1/4-IN SCREW) | ||
| 12. | 244-9639 Y | [1] | BLOCK AS-TERMINAL | |
| 13. | 244-9642 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 7K-1181 | [1] | STRAP-CABLE | ||
| 109-3038 | [5] | END-WIRE (16-GA) | ||
| 162-4171 | [3] | TERMINAL AS (18-GA TO 20-GA) | ||
| 5P-1475 | [1] | TERMINAL-FORK (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7875 E | TUBE-HEAT SHRINK (7.44-MM DIA)(4-CM) | |||
| 14. | 244-9643 | [1] | HARNESS AS-WIRING (CURRENT TRANSFORMER) | |
| 155-2271 | [1] | KIT-CONNECTING PLUG (4-PIN) | ||
| (INCLUDES PLUG AS & WEDGE) | ||||
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8730 | [4] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 125-9993 | [6] | TERMINAL-FORK (14-GA TO 16-GA, NO. 6 SCREW) | ||
| 15. | 244-9646 | [1] | HARNESS AS-CONTROL (LOAD SHARE) | |
| 7K-1181 | [2] | STRAP-CABLE | ||
| 8T-8729 | [13] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8737 | [57] | PLUG-SEAL | ||
| 125-9997 | [12] | TERMINAL-FORK (16-GA TO 22-GA, NO. 6 SCREW) | ||
| 131-1502 | [1] | TERMINAL AS | ||
| 2L-8075 | [1] | TERMINAL-RING (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7874 E | TUBE-HEAT SHRINK (5.72-MM DIA)(3-CM) | |||
| 133-8753 | [1] | RECEPTACLE AS-CONNECTOR (70-PIN) | ||
| 16. | 373-3494 CY | [1] | BOX GP-EXTENSION TERMINAL | |
| 17. | 252-7365 Y | [2] | TRANSFORMER GP-POTENTIAL | |
| 18. | 252-7425 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 2L-8081 | [3] | TERMINAL-RING (14-GA TO 16-GA, 1/2-IN SCREW) | ||
| 7K-1181 | [6] | STRAP-CABLE | ||
| 109-3038 | [3] | END-WIRE (16-GA) | ||
| 19. | 252-7519 | [2] | STRAP | |
| 20. | 7I-2273 M | [6] | BOLT (M5X0.8X16-MM) | |
| 21. | 1D-4533 | [2] | BOLT (1/4-20X2.25-IN) | |
| 22. | 8T-8998 CM | [8] | SCREW-MACHINE (M6X1X20-MM) | |
| 23. | 170-5632 M | [4] | BOLT (M4X0.7X16-MM) | |
| 24. | 4D-3100 | [4] | GROMMET | |
| 25. | 5C-2890 CM | [5] | NUT (M6X1-THD) | |
| 27. | 5C-9553 M | [2] | BOLT (M6X1X16-MM) | |
| 28. | 5P-0537 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 30. | 9S-8750 | [2] | NUT-FULL (1/4-20-THD) | |
| 31. | 9X-8256 | [6] | WASHER (6.6X12X2-MM THK) | |
| 32. | 4B-4274 | [12] | WASHER (5.5X13X1.2-MM THK) | |
| 33. | 5C-2874 M | [6] | NUT (M5X0.8-THD) | |
| 34. | 7X-0620 | [8] | WASHER-HARD (5.5X13X1.6-MM THK) | |
| 35. | 178-9983 CM | [4] | LOCKNUT (M4X0.7-THD) | |
| 36. | 198-4775 | [2] | WASHER-HARD (6.6X15X6-MM THK) | |
| 37. | 8T-4971 M | [1] | BOLT (M6X1X30-MM) | |
| C | CHANGE FROM PREVIOUS TYPE | |||
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP54011574
252-7368: CONTROL GP-LOAD SHARE MODULE
252-7368 CONTROL GP-LOAD SHARE MODULE
S/N YAK1-UP
LOW VOLTAGE
Type 3
FOR USE WITH MUI
AN ATTACHMENT
S/N YAK1-UP
LOW VOLTAGE
Type 3
FOR USE WITH MUI
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 8C-8514 | [2] | SCREW-MACHINE (8-32X0.375-IN) | |
| 2. | 8T-2882 | [1] | HANDLE-PULL | |
| 3. | 1H-4393 | [2] | LOCKWASHER | |
| 4. | 9X-6772 | [1] | STRAP-CABLE | |
| 5. | 131-5454 | [1] | CONTROL AS-ELECTRONIC GOVERNOR | |
| 6. | 135-6898 | [2] | LATCH AS | |
| 7. | 293-9452 | [1] | MOUNTING-CABLE TIE | |
| 8. | 351-9804 | [2] | HINGE | |
| 9. | 235-4451 CM | [8] | BOLT-FLANGE HEAD (M6X1X16-MM) | |
| 10. | 351-9799 Y | [1] | DOOR AS | |
| 11. | 287-7137 | [1] | STRAP AS-GROUND | |
| 2L-8077 | [2] | TERMINAL-RING (14-GA TO 16-GA, 1/4-IN SCREW) | ||
| 12. | 244-9639 Y | [1] | BLOCK AS-TERMINAL | |
| 13. | 244-9642 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 7K-1181 | [1] | STRAP-CABLE | ||
| 109-3038 | [5] | END-WIRE (16-GA) | ||
| 162-4171 | [3] | TERMINAL AS (18-GA TO 20-GA) | ||
| 5P-1475 | [1] | TERMINAL-FORK (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7875 E | TUBE-HEAT SHRINK (7.44-MM DIA)(4-CM) | |||
| 14. | 244-9643 | [1] | HARNESS AS-WIRING (CURRENT TRANSFORMER) | |
| 155-2271 | [1] | KIT-CONNECTING PLUG (4-PIN) | ||
| (INCLUDES PLUG AS, WEDGE & INTERFACE SEAL) | ||||
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8730 | [4] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 125-9993 | [6] | TERMINAL-FORK (14-GA TO 16-GA, NO. 6 SCREW) | ||
| 15. | 244-9646 | [1] | HARNESS AS-CONTROL (LOAD SHARE) | |
| 7K-1181 | [2] | STRAP-CABLE | ||
| 8T-8729 | [13] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8737 | [57] | PLUG-SEAL | ||
| 125-9997 | [12] | TERMINAL-FORK (16-GA TO 22-GA, NO. 6 SCREW) | ||
| 131-1502 | [1] | TERMINAL AS | ||
| 2L-8075 | [1] | TERMINAL-RING (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7874 E | TUBE-HEAT SHRINK (5.72-MM DIA)(3-CM) | |||
| 133-8753 | [1] | RECEPTACLE AS-CONNECTOR (70-PIN) | ||
| 16. | 373-3494 Y | [1] | BOX GP-EXTENSION TERMINAL | |
| 17. | 252-7365 Y | [2] | TRANSFORMER GP-POTENTIAL | |
| 18. | 252-7425 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 2L-8081 | [3] | TERMINAL-RING (14-GA TO 16-GA, 1/2-IN SCREW) | ||
| 7K-1181 | [6] | STRAP-CABLE | ||
| 109-3038 | [3] | END-WIRE (16-GA) | ||
| 19. | 252-7519 | [2] | STRAP | |
| 20. | 7I-2273 M | [6] | BOLT (M5X0.8X16-MM) | |
| 21. | 1D-4533 | [2] | BOLT (1/4-20X2.25-IN) | |
| 22. | 8T-8998 M | [8] | SCREW-MACHINE (M6X1X20-MM) | |
| 23. | 170-5632 M | [4] | BOLT (M4X0.7X16-MM) | |
| 24. | 4D-3100 | [4] | GROMMET | |
| 25. | 5C-2890 M | [5] | NUT (M6X1-THD) | |
| 27. | 5C-9553 M | [2] | BOLT (M6X1X16-MM) | |
| 28. | 5P-0537 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 30. | 9S-8750 | [2] | NUT-FULL (1/4-20-THD) | |
| 31. | 9X-8256 | [6] | WASHER (6.6X12X2-MM THK) | |
| 32. | 4B-4274 | [12] | WASHER (5.5X13X1.2-MM THK) | |
| 33. | 5C-2874 M | [6] | NUT (M5X0.8-THD) | |
| 34. | 7X-0620 | [8] | WASHER-HARD (5.5X13X1.6-MM THK) | |
| 35. | 178-9983 M | [4] | LOCKNUT (M4X0.7-THD) | |
| 36. | 198-4775 | [2] | WASHER-HARD (6.6X15X6-MM THK) | |
| 37. | 8T-4971 M | [1] | BOLT (M6X1X30-MM) | |
| 38. | 243-5027 CM | [2] | NUT (M6X1-THD) | |
| C | CHANGE FROM PREVIOUS TYPE | |||
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP54011575
252-7369: CONTROL GP-LOAD SHARE MODULE
252-7369 CONTROL GP-LOAD SHARE MODULE
S/N YAK1-UP
Type 1
FOR USE WITH EUI, LOW VOLTAGE
AN ATTACHMENT
S/N YAK1-UP
Type 1
FOR USE WITH EUI, LOW VOLTAGE
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 4W-5972 | [1] | KNOB | |
| 2. | 5L-5180 | [1] | WASHER (0.49X0.875X0.05-IN THK) | |
| 3. | 7C-4550 | [1] | SEAL (ROTATING SHAFT) | |
| 4. | 8C-8514 | [2] | SCREW-MACHINE (8-32X0.375-IN) | |
| 5. | 8T-2882 | [1] | HANDLE-PULL | |
| 6. | 1H-4393 | [2] | LOCKWASHER | |
| 7. | 9X-6772 | [1] | STRAP-CABLE | |
| 8. | 127-9070 | [1] | POTENTIOMETER (10,000-OHM)(VOLTAGE ADJUSTMENT) | |
| 9. | 135-6898 | [2] | LATCH AS | |
| 10. | 293-9452 | [1] | MOUNTING-CABLE TIE | |
| 11. | 169-4481 | [2] | HINGE AS | |
| 12. | 235-4451 M | [10] | BOLT-FLANGE HEAD (M6X1X16-MM) | |
| 13. | 242-8835 | [1] | DOOR AS | |
| 14. | 244-9639 Y | [1] | BLOCK AS-TERMINAL | |
| 15. | 244-9642 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 7K-1181 | [1] | STRAP-CABLE | ||
| 109-3038 | [5] | END-WIRE (16-GA) | ||
| 162-4171 | [3] | TERMINAL AS (18-GA TO 20-GA) | ||
| 5P-1475 | [1] | TERMINAL-FORK (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7875 E | TUBE-HEAT SHRINK (7.44-MM DIA)(4-CM) | |||
| 16. | 244-9643 | [1] | HARNESS AS-WIRING (CURRENT TRANSFORMER) | |
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8730 | [4] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 125-9993 | [6] | TERMINAL-FORK (14-GA TO 16-GA, NO. 6 SCREW) | ||
| 155-2271 | [1] | KIT-CONNECTING PLUG (4-PIN) | ||
| (INCLUDES PLUG AS & WEDGE) | ||||
| 17. | 244-9644 | [1] | HARNESS AS-CONTROL (LOAD SHARE MODULE) | |
| 7K-1181 | [2] | STRAP-CABLE | ||
| 8T-8729 | [6] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8737 | [62] | PLUG-SEAL | ||
| 125-9997 | [7] | TERMINAL-FORK (16-GA TO 22-GA, NO. 6 SCREW) | ||
| 126-1767 | [2] | PIN-CONNECTOR (14-GA TO 16-GA) | ||
| 131-1502 | [1] | TERMINAL AS | ||
| 2L-8075 | [1] | TERMINAL-RING (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 125-7874 E | TUBE-HEAT SHRINK (5.72-MM DIA)(3-CM) | |||
| 133-8753 | [1] | RECEPTACLE AS-CONNECTOR (70-PIN) | ||
| 18. | 245-0074 | [1] | BOX GP-EXTENSION TERMINAL | |
| 18A. | 244-9669 | [1] | BOX AS | |
| 18B. | 244-9631 J | SEAL (4.3-DM EACH) | ||
| 18C. | 244-9631 J | SEAL (6.5-DM EACH) | ||
| 18D. | 6V-9335 D | SEAL (0.4-M EACH) | ||
| 18E. | 6V-9335 D | SEAL (0.6-M EACH) | ||
| 19. | 252-7365 Y | [2] | TRANSFORMER GP-POTENTIAL | |
| 20. | 252-7425 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 2L-8081 | [3] | TERMINAL-RING (14-GA TO 16-GA, 1/2-IN SCREW) | ||
| 7K-1181 | [6] | STRAP-CABLE | ||
| 109-3038 | [3] | END-WIRE (16-GA) | ||
| 21. | 252-7519 | [2] | STRAP | |
| 22. | 287-7137 | [1] | STRAP AS-GROUND | |
| 2L-8077 | [2] | TERMINAL-RING (14-GA TO 16-GA, 1/4-IN SCREW) | ||
| 23. | 309-1583 | [1] | CONTROL AS-GOVERNOR (LOAD SHARE) | |
| 24. | 1D-4533 | [2] | BOLT (1/4-20X2.25-IN) | |
| 25. | 3B-4504 | [8] | LOCKWASHER | |
| 26. | 7X-0620 | [16] | WASHER-HARD (5.5X13X1.6-MM THK) | |
| 27. | 4D-3100 | [4] | GROMMET | |
| 29. | 5C-2890 M | [13] | NUT (M6X1-THD) | |
| 30. | 5C-9553 M | [2] | BOLT (M6X1X16-MM) | |
| 31. | 5P-0537 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 33. | 260-6675 | [8] | NUT-SELF LOCKING (M4X0.7-THD) | |
| 34. | 9S-8750 | [2] | NUT-FULL (1/4-20-THD) | |
| 35. | 170-5632 M | [8] | BOLT (M4X0.7X16-MM) | |
| 36. | 9X-8256 | [6] | WASHER (6.6X12X2-MM THK) | |
| 37. | 198-4775 | [2] | WASHER-HARD (6.6X15X6-MM THK) | |
| 38. | 8T-4971 M | [1] | BOLT (M6X1X30-MM) | |
| D | ORDER BY THE METER | |||
| E | ORDER BY THE CENTIMETER | |||
| J | ORDER BY THE DECIMETER | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP54011576
252-7369: CONTROL GP-LOAD SHARE MODULE
252-7369 CONTROL GP-LOAD SHARE MODULE
S/N YAK1-UP
Type 2
FOR USE WITH EUI, LOW VOLTAGE
AN ATTACHMENT
S/N YAK1-UP
Type 2
FOR USE WITH EUI, LOW VOLTAGE
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 4W-5972 | [1] | KNOB | |
| 2. | 5L-5180 | [1] | WASHER (0.49X0.875X0.05-IN THK) | |
| 3. | 7C-4550 | [1] | SEAL (ROTATING SHAFT) | |
| 4. | 8C-8514 | [2] | SCREW-MACHINE (8-32X0.375-IN) | |
| 5. | 8T-2882 | [1] | HANDLE-PULL | |
| 6. | 1H-4393 | [2] | LOCKWASHER | |
| 7. | 9X-6772 | [1] | STRAP-CABLE | |
| 8. | 127-9070 | [1] | POTENTIOMETER (10,000-OHM)(VOLTAGE ADJUSTMENT) | |
| 9. | 135-6898 | [2] | LATCH AS | |
| 10. | 293-9452 | [1] | MOUNTING-CABLE TIE | |
| 11. | 351-9804 C | [2] | HINGE | |
| 12. | 235-4451 M | [8] | BOLT-FLANGE HEAD (M6X1X16-MM) | |
| 13. | 351-9799 C | [1] | DOOR AS | |
| 6V-9632 M | [4] | NUT-WELD (M6X1-THD) | ||
| 14. | 244-9639 Y | [1] | BLOCK AS-TERMINAL | |
| 15. | 244-9642 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 7K-1181 | [1] | STRAP-CABLE | ||
| 109-3038 | [5] | END-WIRE (16-GA) | ||
| 162-4171 | [3] | TERMINAL AS (18-GA TO 20-GA) | ||
| (EACH INCLUDES) | ||||
| 5P-1475 | [1] | TERMINAL-FORK (14-GA TO 16-GA, NO. 8 SCREW) | ||
| 16. | 244-9643 | [1] | HARNESS AS-WIRING (CURRENT TRANSFORMER) | |
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 8T-8729 | [4] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 8T-8730 | [4] | SOCKET-CONNECTOR (16-GA TO 18-GA) | ||
| 125-9993 | [6] | TERMINAL-FORK (14-GA TO 16-GA, NO. 6 SCREW) | ||
| 155-2271 | [1] | KIT-CONNECTING PLUG (4-PIN) | ||
| (INCLUDES PLUG AS, WEDGE, & INTERFACE SEAL) | ||||
| 17. | 244-9644 Y | [1] | HARNESS AS-CONTROL (LOAD SHARE MODULE) | |
| 18. | 373-3494 CY | [1] | BOX GP-EXTENSION TERMINAL | |
| 19. | 252-7365 Y | [2] | TRANSFORMER GP-POTENTIAL | |
| 20. | 252-7425 | [1] | HARNESS AS-WIRING (VOLTAGE SENSING) | |
| 2L-8081 | [3] | TERMINAL-RING (14-GA TO 16-GA, 1/2-IN SCREW) | ||
| 7K-1181 | [6] | STRAP-CABLE | ||
| 109-3038 | [3] | END-WIRE (16-GA) | ||
| 21. | 252-7519 | [2] | STRAP | |
| 22. | 287-7137 | [1] | STRAP AS-GROUND | |
| 2L-8077 | [2] | TERMINAL-RING (14-GA TO 16-GA, 1/4-IN SCREW) | ||
| 23. | 309-1583 | [1] | CONTROL AS-GOVERNOR (LOAD SHARE) | |
| 24. | 1D-4533 | [2] | BOLT (1/4-20X2.25-IN) | |
| 25. | 8T-8998 CM | [8] | SCREW-MACHINE (M6X1X20-MM) | |
| 26. | 7X-0620 | [16] | WASHER-HARD (5.5X13X1.6-MM THK) | |
| 27. | 4D-3100 | [4] | GROMMET | |
| 29. | 5C-2890 CM | [5] | NUT (M6X1-THD) | |
| 30. | 5C-9553 M | [2] | BOLT (M6X1X16-MM) | |
| 31. | 5P-0537 | [4] | WASHER-HARD (7.2X14.5X2-MM THK) | |
| 33. | 178-9983 CM | [8] | LOCKNUT (M4X0.7-THD) | |
| 34. | 9S-8750 | [2] | NUT-FULL (1/4-20-THD) | |
| 35. | 170-5632 M | [8] | BOLT (M4X0.7X16-MM) | |
| 36. | 9X-8256 | [6] | WASHER (6.6X12X2-MM THK) | |
| 37. | 198-4775 | [2] | WASHER-HARD (6.6X15X6-MM THK) | |
| 38. | 8T-4971 M | [1] | BOLT (M6X1X30-MM) | |
| 39. | 243-5027 M | [2] | NUT (M6X1-THD) | |
| C | CHANGE FROM PREVIOUS TYPE | |||
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP54011577
252-7416: CONTROL GP-LOAD SHARE MODULE
252-7416 CONTROL GP-LOAD SHARE MODULE
S/N YAK1-UP
FOR USE WITH MUI LOW, MEDIUM VOLT
AN ATTACHMENT
S/N YAK1-UP
FOR USE WITH MUI LOW, MEDIUM VOLT
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9X-6772 | [3] | STRAP-CABLE | |
| 2. | 131-5454 | [1] | CONTROL AS-ELECTRONIC GOVERNOR | |
| 3. | 156-6175 | [3] | CLIP (LADDER) | |
| 4. | 244-9643 | [1] | HARNESS AS-WIRING (CURRENT TRANSFORMER) | |
| 102-8804 | [1] | KIT-RECEPTACLE (4-PIN) | ||
| (INCLUDES RECEPTACLE AS. & WEDGE) | ||||
| 155-2272 | [1] | PLUG AS-CONNECTOR (4-PIN) | ||
| (INCLUDES RECEPTACLE & WEDGE) | ||||
| 162-4171 | [6] | TERMINAL AS (18-GA TO 20-GA) | ||
| 5. | 252-7358 | [1] | HARNESS AS-WIRING (TERMINAL STRIP) | |
| 7K-1181 | [4] | STRAP-CABLE | ||
| 109-3038 | [5] | END-WIRE (16-GA) | ||
| 162-4171 | [3] | TERMINAL AS (18-GA TO 20-GA) | ||
| 6. | 252-7434 | [1] | HARNESS AS-CONTROL (LOAD SHARE MODULE) | |
| 133-8753 | [1] | RECEPTACLE AS-CONNECTOR (70-PIN) | ||
| 134-6258 E | CABLE-ELECTRICAL (16-GA)(508-CM) | |||
| 162-4171 | [13] | TERMINAL AS (18-GA TO 20-GA) | ||
| 7. | 112-8372 M | [6] | BOLT (M4X0.7X16-MM) | |
| 8. | 5C-2890 M | [3] | NUT (M6X1-THD) | |
| 9. | 5C-8312 M | [6] | NUT (M4X0.7-THD) | |
| 10. | 5C-9553 M | [3] | BOLT (M6X1X16-MM) | |
| 11. | 8T-0328 | [12] | WASHER-HARD (5.5X10X1-MM THK) | |
| 12. | 9X-8256 | [6] | WASHER (6.6X12X2-MM THK) | |
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
#SEBP54011578
252-7417: CONTROL GP-LOAD SHARE MODULE
252-7417 CONTROL GP-LOAD SHARE MODULE
S/N YAK1-UP
FOR USE WITH EUI, MEDIUM VOLT
AN ATTACHMENT
S/N YAK1-UP
FOR USE WITH EUI, MEDIUM VOLT
AN ATTACHMENT
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9X-6772 | [3] | STRAP-CABLE | |
| 2. | 127-9070 | [1] | POTENTIOMETER (10,000-OHM)(VOLTAGE ADJUSTMENT) | |
| 3. | 156-6175 | [3] | CLIP (LADDER) | |
| 4. | 309-1583 | [1] | CONTROL AS-GOVERNOR (LOAD SHARE) | |
| 5. | 244-9643 | [1] | HARNESS AS-WIRING (CURRENT TRANSFORMER) | |
| 6. | 252-7358 | [1] | HARNESS AS-WIRING (TERMINAL STRIP) | |
| 7. | 252-7435 | [1] | HARNESS AS-CONTROL (LOAD SHARE) | |
| 8. | 112-8372 M | [4] | BOLT (M4X0.7X16-MM) | |
| 9. | 5C-2890 M | [3] | NUT (M6X1-THD) | |
| 10. | 5C-8312 M | [4] | NUT (M4X0.7-THD) | |
| 11. | 5C-9553 M | [3] | BOLT (M6X1X16-MM) | |
| 12. | 8T-0328 | [8] | WASHER-HARD (5.5X10X1-MM THK) | |
| 13. | 9X-8256 | [6] | WASHER (6.6X12X2-MM THK) | |
| 14. | 4W-5972 | [1] | KNOB | |
| 15. | 5L-5180 | [1] | WASHER (0.49X0.875X0.05-IN THK) | |
| 16. | 7C-4550 | [1] | SEAL (ROTATING SHAFT) | |
| M | METRIC PART | |||
#SEBP54011579
252-7556: COVER GP-CONTROL PANEL
For full view, you need register
Parts for your 3512 GENERATOR SET:
CATERPILLAR SISInformation:
ELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINE
Operation and Maintenance Manual
Special Instruction
Diagnostic Code Information for Caterpillar <SUP>®</SUP> Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Diagnostic Code Information for Caterpillar ® Electronic Control {1901, 1927, 1948, 3168, 4348, 4802, 4808, 4810, 5511, 5701, 7490, 7494, 7601, 7602, 7610, 7610, 7610}
Systems Operation
Testing and Adjusting
Service Magazine
Caterpillar Parts SIS Catalog 3512 :
Truck sale:
230,416
230,416
238,453
178,974
178,974